initial commit

COMPILED_FIRMWARE/README.md

@@ -0,0 +1,12 @@
+This is the complete firmware file. 
+
+You can write it to STM32F103 bluepill board with 
+
+- SWD upload using JLink2 and ST JLink Utility
+
+or
+
+- Serial upload using UART adapter and ST FlashLoader Demonstrator
+  This is the same procedure as uploading a USB bootloader:
+    https://www.electronicshub.org/how-to-upload-stm32f103c8t6-usb-bootloader
+    just select the "freedmo.bin" in "Download from file" (2)

Drivers/CMSIS/Device/ST/STM32F1xx/Include/stm32f1xx.h

@@ -0,0 +1,275 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx.h
+  * @author  MCD Application Team
+  * @brief   CMSIS STM32F1xx Device Peripheral Access Layer Header File. 
+  *
+  *          The file is the unique include file that the application programmer
+  *          is using in the C source code, usually in main.c. This file contains:
+  *            - Configuration section that allows to select:
+  *              - The STM32F1xx device used in the target application
+  *              - To use or not the peripheral<61>s drivers in application code(i.e. 
+  *                code will be based on direct access to peripheral<61>s registers 
+  *                rather than drivers API), this option is controlled by 
+  *                "#define USE_HAL_DRIVER"
+  *  
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2017 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/** @addtogroup CMSIS
+  * @{
+  */
+
+/** @addtogroup stm32f1xx
+  * @{
+  */
+    
+#ifndef __STM32F1XX_H
+#define __STM32F1XX_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif /* __cplusplus */
+  
+/** @addtogroup Library_configuration_section
+  * @{
+  */
+
+/**
+  * @brief STM32 Family
+  */
+#if !defined (STM32F1)
+#define STM32F1
+#endif /* STM32F1 */
+
+/* Uncomment the line below according to the target STM32L device used in your 
+   application 
+  */
+
+#if !defined (STM32F100xB) && !defined (STM32F100xE) && !defined (STM32F101x6) && \
+    !defined (STM32F101xB) && !defined (STM32F101xE) && !defined (STM32F101xG) && !defined (STM32F102x6) && !defined (STM32F102xB) && !defined (STM32F103x6) && \
+    !defined (STM32F103xB) && !defined (STM32F103xE) && !defined (STM32F103xG) && !defined (STM32F105xC) && !defined (STM32F107xC)
+  /* #define STM32F100xB  */   /*!< STM32F100C4, STM32F100R4, STM32F100C6, STM32F100R6, STM32F100C8, STM32F100R8, STM32F100V8, STM32F100CB, STM32F100RB and STM32F100VB */
+  /* #define STM32F100xE */    /*!< STM32F100RC, STM32F100VC, STM32F100ZC, STM32F100RD, STM32F100VD, STM32F100ZD, STM32F100RE, STM32F100VE and STM32F100ZE */
+  /* #define STM32F101x6  */   /*!< STM32F101C4, STM32F101R4, STM32F101T4, STM32F101C6, STM32F101R6 and STM32F101T6 Devices */
+  /* #define STM32F101xB  */   /*!< STM32F101C8, STM32F101R8, STM32F101T8, STM32F101V8, STM32F101CB, STM32F101RB, STM32F101TB and STM32F101VB */
+  /* #define STM32F101xE */    /*!< STM32F101RC, STM32F101VC, STM32F101ZC, STM32F101RD, STM32F101VD, STM32F101ZD, STM32F101RE, STM32F101VE and STM32F101ZE */ 
+  /* #define STM32F101xG  */   /*!< STM32F101RF, STM32F101VF, STM32F101ZF, STM32F101RG, STM32F101VG and STM32F101ZG */
+  /* #define STM32F102x6 */    /*!< STM32F102C4, STM32F102R4, STM32F102C6 and STM32F102R6 */
+  /* #define STM32F102xB  */   /*!< STM32F102C8, STM32F102R8, STM32F102CB and STM32F102RB */
+  /* #define STM32F103x6  */   /*!< STM32F103C4, STM32F103R4, STM32F103T4, STM32F103C6, STM32F103R6 and STM32F103T6 */
+  /* #define STM32F103xB  */   /*!< STM32F103C8, STM32F103R8, STM32F103T8, STM32F103V8, STM32F103CB, STM32F103RB, STM32F103TB and STM32F103VB */
+  /* #define STM32F103xE */    /*!< STM32F103RC, STM32F103VC, STM32F103ZC, STM32F103RD, STM32F103VD, STM32F103ZD, STM32F103RE, STM32F103VE and STM32F103ZE */
+  /* #define STM32F103xG  */   /*!< STM32F103RF, STM32F103VF, STM32F103ZF, STM32F103RG, STM32F103VG and STM32F103ZG */
+  /* #define STM32F105xC */    /*!< STM32F105R8, STM32F105V8, STM32F105RB, STM32F105VB, STM32F105RC and STM32F105VC */
+  /* #define STM32F107xC  */   /*!< STM32F107RB, STM32F107VB, STM32F107RC and STM32F107VC */  
+#endif
+
+/*  Tip: To avoid modifying this file each time you need to switch between these
+        devices, you can define the device in your toolchain compiler preprocessor.
+  */
+  
+#if !defined  (USE_HAL_DRIVER)
+/**
+ * @brief Comment the line below if you will not use the peripherals drivers.
+   In this case, these drivers will not be included and the application code will 
+   be based on direct access to peripherals registers 
+   */
+  /*#define USE_HAL_DRIVER */
+#endif /* USE_HAL_DRIVER */
+
+/**
+  * @brief CMSIS Device version number V4.3.3
+  */
+#define __STM32F1_CMSIS_VERSION_MAIN   (0x04) /*!< [31:24] main version */
+#define __STM32F1_CMSIS_VERSION_SUB1   (0x03) /*!< [23:16] sub1 version */
+#define __STM32F1_CMSIS_VERSION_SUB2   (0x03) /*!< [15:8]  sub2 version */
+#define __STM32F1_CMSIS_VERSION_RC     (0x00) /*!< [7:0]  release candidate */ 
+#define __STM32F1_CMSIS_VERSION        ((__STM32F1_CMSIS_VERSION_MAIN << 24)\
+                                       |(__STM32F1_CMSIS_VERSION_SUB1 << 16)\
+                                       |(__STM32F1_CMSIS_VERSION_SUB2 << 8 )\
+                                       |(__STM32F1_CMSIS_VERSION_RC))
+
+/**
+  * @}
+  */
+
+/** @addtogroup Device_Included
+  * @{
+  */
+
+#if defined(STM32F100xB)
+  #include "stm32f100xb.h"
+#elif defined(STM32F100xE)
+  #include "stm32f100xe.h"
+#elif defined(STM32F101x6)
+  #include "stm32f101x6.h"
+#elif defined(STM32F101xB)
+  #include "stm32f101xb.h"
+#elif defined(STM32F101xE)
+  #include "stm32f101xe.h"
+#elif defined(STM32F101xG)
+  #include "stm32f101xg.h"
+#elif defined(STM32F102x6)
+  #include "stm32f102x6.h"
+#elif defined(STM32F102xB)
+  #include "stm32f102xb.h"
+#elif defined(STM32F103x6)
+  #include "stm32f103x6.h"
+#elif defined(STM32F103xB)
+  #include "stm32f103xb.h"
+#elif defined(STM32F103xE)
+  #include "stm32f103xe.h"
+#elif defined(STM32F103xG)
+  #include "stm32f103xg.h"
+#elif defined(STM32F105xC)
+  #include "stm32f105xc.h"
+#elif defined(STM32F107xC)
+  #include "stm32f107xc.h"
+#else
+ #error "Please select first the target STM32F1xx device used in your application (in stm32f1xx.h file)"
+#endif
+
+/**
+  * @}
+  */
+
+/** @addtogroup Exported_types
+  * @{
+  */  
+typedef enum 
+{
+  RESET = 0, 
+  SET = !RESET
+} FlagStatus, ITStatus;
+
+typedef enum 
+{
+  DISABLE = 0, 
+  ENABLE = !DISABLE
+} FunctionalState;
+#define IS_FUNCTIONAL_STATE(STATE) (((STATE) == DISABLE) || ((STATE) == ENABLE))
+
+typedef enum
+{
+  SUCCESS = 0U,
+  ERROR = !SUCCESS
+} ErrorStatus;
+
+/**
+  * @}
+  */
+
+
+/** @addtogroup Exported_macros
+  * @{
+  */
+#define SET_BIT(REG, BIT)     ((REG) |= (BIT))
+
+#define CLEAR_BIT(REG, BIT)   ((REG) &= ~(BIT))
+
+#define READ_BIT(REG, BIT)    ((REG) & (BIT))
+
+#define CLEAR_REG(REG)        ((REG) = (0x0))
+
+#define WRITE_REG(REG, VAL)   ((REG) = (VAL))
+
+#define READ_REG(REG)         ((REG))
+
+#define MODIFY_REG(REG, CLEARMASK, SETMASK)  WRITE_REG((REG), (((READ_REG(REG)) & (~(CLEARMASK))) | (SETMASK)))
+
+#define POSITION_VAL(VAL)     (__CLZ(__RBIT(VAL))) 
+
+/* Use of CMSIS compiler intrinsics for register exclusive access */
+/* Atomic 32-bit register access macro to set one or several bits */
+#define ATOMIC_SET_BIT(REG, BIT)                             \
+  do {                                                       \
+    uint32_t val;                                            \
+    do {                                                     \
+      val = __LDREXW((__IO uint32_t *)&(REG)) | (BIT);       \
+    } while ((__STREXW(val,(__IO uint32_t *)&(REG))) != 0U); \
+  } while(0)
+
+/* Atomic 32-bit register access macro to clear one or several bits */
+#define ATOMIC_CLEAR_BIT(REG, BIT)                           \
+  do {                                                       \
+    uint32_t val;                                            \
+    do {                                                     \
+      val = __LDREXW((__IO uint32_t *)&(REG)) & ~(BIT);      \
+    } while ((__STREXW(val,(__IO uint32_t *)&(REG))) != 0U); \
+  } while(0)
+
+/* Atomic 32-bit register access macro to clear and set one or several bits */
+#define ATOMIC_MODIFY_REG(REG, CLEARMSK, SETMASK)                          \
+  do {                                                                     \
+    uint32_t val;                                                          \
+    do {                                                                   \
+      val = (__LDREXW((__IO uint32_t *)&(REG)) & ~(CLEARMSK)) | (SETMASK); \
+    } while ((__STREXW(val,(__IO uint32_t *)&(REG))) != 0U);               \
+  } while(0)
+
+/* Atomic 16-bit register access macro to set one or several bits */
+#define ATOMIC_SETH_BIT(REG, BIT)                            \
+  do {                                                       \
+    uint16_t val;                                            \
+    do {                                                     \
+      val = __LDREXH((__IO uint16_t *)&(REG)) | (BIT);       \
+    } while ((__STREXH(val,(__IO uint16_t *)&(REG))) != 0U); \
+  } while(0)
+
+/* Atomic 16-bit register access macro to clear one or several bits */
+#define ATOMIC_CLEARH_BIT(REG, BIT)                          \
+  do {                                                       \
+    uint16_t val;                                            \
+    do {                                                     \
+      val = __LDREXH((__IO uint16_t *)&(REG)) & ~(BIT);      \
+    } while ((__STREXH(val,(__IO uint16_t *)&(REG))) != 0U); \
+  } while(0)
+
+/* Atomic 16-bit register access macro to clear and set one or several bits */
+#define ATOMIC_MODIFYH_REG(REG, CLEARMSK, SETMASK)                         \
+  do {                                                                     \
+    uint16_t val;                                                          \
+    do {                                                                   \
+      val = (__LDREXH((__IO uint16_t *)&(REG)) & ~(CLEARMSK)) | (SETMASK); \
+    } while ((__STREXH(val,(__IO uint16_t *)&(REG))) != 0U);               \
+  } while(0)
+
+
+/**
+  * @}
+  */
+
+#if defined (USE_HAL_DRIVER)
+ #include "stm32f1xx_hal.h"
+#endif /* USE_HAL_DRIVER */
+
+
+#ifdef __cplusplus
+}
+#endif /* __cplusplus */
+
+#endif /* __STM32F1xx_H */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+  
+
+
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/CMSIS/Device/ST/STM32F1xx/Include/system_stm32f1xx.h

@@ -0,0 +1,98 @@
+/**
+  ******************************************************************************
+  * @file    system_stm32f10x.h
+  * @author  MCD Application Team
+  * @brief   CMSIS Cortex-M3 Device Peripheral Access Layer System Header File.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2017 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/** @addtogroup CMSIS
+  * @{
+  */
+
+/** @addtogroup stm32f10x_system
+  * @{
+  */  
+  
+/**
+  * @brief Define to prevent recursive inclusion
+  */
+#ifndef __SYSTEM_STM32F10X_H
+#define __SYSTEM_STM32F10X_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif 
+
+/** @addtogroup STM32F10x_System_Includes
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+
+/** @addtogroup STM32F10x_System_Exported_types
+  * @{
+  */
+
+extern uint32_t SystemCoreClock;          /*!< System Clock Frequency (Core Clock) */
+extern const uint8_t  AHBPrescTable[16U];  /*!< AHB prescalers table values */
+extern const uint8_t  APBPrescTable[8U];   /*!< APB prescalers table values */
+
+/**
+  * @}
+  */
+
+/** @addtogroup STM32F10x_System_Exported_Constants
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @addtogroup STM32F10x_System_Exported_Macros
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @addtogroup STM32F10x_System_Exported_Functions
+  * @{
+  */
+  
+extern void SystemInit(void);
+extern void SystemCoreClockUpdate(void);
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /*__SYSTEM_STM32F10X_H */
+
+/**
+  * @}
+  */
+  
+/**
+  * @}
+  */  
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/CMSIS/Device/ST/STM32F1xx/License.md

@@ -0,0 +1,83 @@
+Apache License
+ Version 2.0, January 2004
+ http://www.apache.org/licenses/
+
+TERMS AND CONDITIONS FOR USE, REPRODUCTION, AND DISTRIBUTION
+
+1. Definitions.
+
+"License" shall mean the terms and conditions for use, reproduction, and distribution as defined by Sections 1 through 9 of this document.
+
+"Licensor" shall mean the copyright owner or entity authorized by the copyright owner that is granting the License.
+
+"Legal Entity" shall mean the union of the acting entity and all other entities that control, are controlled by, or are under common control with that entity. For the purposes of this definition, "control" means (i) the power, direct or indirect, to cause the direction or management of such entity, whether by contract or otherwise, or (ii) ownership of fifty percent (50%) or more of the outstanding shares, or (iii) beneficial ownership of such entity.
+
+"You" (or "Your") shall mean an individual or Legal Entity exercising permissions granted by this License.
+
+"Source" form shall mean the preferred form for making modifications, including but not limited to software source code, documentation source, and configuration files.
+
+"Object" form shall mean any form resulting from mechanical transformation or translation of a Source form, including but not limited to compiled object code, generated documentation, and conversions to other media types.
+
+"Work" shall mean the work of authorship, whether in Source or Object form, made available under the License, as indicated by a copyright notice that is included in or attached to the work (an example is provided in the Appendix below).
+
+"Derivative Works" shall mean any work, whether in Source or Object form, that is based on (or derived from) the Work and for which the editorial revisions, annotations, elaborations, or other modifications represent, as a whole, an original work of authorship. For the purposes of this License, Derivative Works shall not include works that remain separable from, or merely link (or bind by name) to the interfaces of, the Work and Derivative Works thereof.
+
+"Contribution" shall mean any work of authorship, including the original version of the Work and any modifications or additions to that Work or Derivative Works thereof, that is intentionally submitted to Licensor for inclusion in the Work by the copyright owner or by an individual or Legal Entity authorized to submit on behalf of the copyright owner. For the purposes of this definition, "submitted" means any form of electronic, verbal, or written communication sent to the Licensor or its representatives, including but not limited to communication on electronic mailing lists, source code control systems, and issue tracking systems that are managed by, or on behalf of, the Licensor for the purpose of discussing and improving the Work, but excluding communication that is conspicuously marked or otherwise designated in writing by the copyright owner as "Not a Contribution."
+
+"Contributor" shall mean Licensor and any individual or Legal Entity on behalf of whom a Contribution has been received by Licensor and subsequently incorporated within the Work.
+
+2. Grant of Copyright License.
+
+Subject to the terms and conditions of this License, each Contributor hereby grants to You a perpetual, worldwide, non-exclusive, no-charge, royalty-free, irrevocable copyright license to reproduce, prepare Derivative Works of, publicly display, publicly perform, sublicense, and distribute the Work and such Derivative Works in Source or Object form.
+
+3. Grant of Patent License.
+
+Subject to the terms and conditions of this License, each Contributor hereby grants to You a perpetual, worldwide, non-exclusive, no-charge, royalty-free, irrevocable (except as stated in this section) patent license to make, have made, use, offer to sell, sell, import, and otherwise transfer the Work, where such license applies only to those patent claims licensable by such Contributor that are necessarily infringed by their Contribution(s) alone or by combination of their Contribution(s) with the Work to which such Contribution(s) was submitted. If You institute patent litigation against any entity (including a cross-claim or counterclaim in a lawsuit) alleging that the Work or a Contribution incorporated within the Work constitutes direct or contributory patent infringement, then any patent licenses granted to You under this License for that Work shall terminate as of the date such litigation is filed.
+
+4. Redistribution.
+
+You may reproduce and distribute copies of the Work or Derivative Works thereof in any medium, with or without modifications, and in Source or Object form, provided that You meet the following conditions:
+1.You must give any other recipients of the Work or Derivative Works a copy of this License; and
+2.You must cause any modified files to carry prominent notices stating that You changed the files; and
+3.You must retain, in the Source form of any Derivative Works that You distribute, all copyright, patent, trademark, and attribution notices from the Source form of the Work, excluding those notices that do not pertain to any part of the Derivative Works; and
+4.If the Work includes a "NOTICE" text file as part of its distribution, then any Derivative Works that You distribute must include a readable copy of the attribution notices contained within such NOTICE file, excluding those notices that do not pertain to any part of the Derivative Works, in at least one of the following places: within a NOTICE text file distributed as part of the Derivative Works; within the Source form or documentation, if provided along with the Derivative Works; or, within a display generated by the Derivative Works, if and wherever such third-party notices normally appear. The contents of the NOTICE file are for informational purposes only and do not modify the License. You may add Your own attribution notices within Derivative Works that You distribute, alongside or as an addendum to the NOTICE text from the Work, provided that such additional attribution notices cannot be construed as modifying the License.
+
+You may add Your own copyright statement to Your modifications and may provide additional or different license terms and conditions for use, reproduction, or distribution of Your modifications, or for any such Derivative Works as a whole, provided Your use, reproduction, and distribution of the Work otherwise complies with the conditions stated in this License.
+
+5. Submission of Contributions.
+
+Unless You explicitly state otherwise, any Contribution intentionally submitted for inclusion in the Work by You to the Licensor shall be under the terms and conditions of this License, without any additional terms or conditions. Notwithstanding the above, nothing herein shall supersede or modify the terms of any separate license agreement you may have executed with Licensor regarding such Contributions.
+
+6. Trademarks.
+
+This License does not grant permission to use the trade names, trademarks, service marks, or product names of the Licensor, except as required for reasonable and customary use in describing the origin of the Work and reproducing the content of the NOTICE file.
+
+7. Disclaimer of Warranty.
+
+Unless required by applicable law or agreed to in writing, Licensor provides the Work (and each Contributor provides its Contributions) on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied, including, without limitation, any warranties or conditions of TITLE, NON-INFRINGEMENT, MERCHANTABILITY, or FITNESS FOR A PARTICULAR PURPOSE. You are solely responsible for determining the appropriateness of using or redistributing the Work and assume any risks associated with Your exercise of permissions under this License.
+
+8. Limitation of Liability.
+
+In no event and under no legal theory, whether in tort (including negligence), contract, or otherwise, unless required by applicable law (such as deliberate and grossly negligent acts) or agreed to in writing, shall any Contributor be liable to You for damages, including any direct, indirect, special, incidental, or consequential damages of any character arising as a result of this License or out of the use or inability to use the Work (including but not limited to damages for loss of goodwill, work stoppage, computer failure or malfunction, or any and all other commercial damages or losses), even if such Contributor has been advised of the possibility of such damages.
+
+9. Accepting Warranty or Additional Liability.
+
+While redistributing the Work or Derivative Works thereof, You may choose to offer, and charge a fee for, acceptance of support, warranty, indemnity, or other liability obligations and/or rights consistent with this License. However, in accepting such obligations, You may act only on Your own behalf and on Your sole responsibility, not on behalf of any other Contributor, and only if You agree to indemnify, defend, and hold each Contributor harmless for any liability incurred by, or claims asserted against, such Contributor by reason of your accepting any such warranty or additional liability.
+
+END OF TERMS AND CONDITIONS
+
+APPENDIX:
+
+   Copyright [2019] [STMicroelectronics]
+
+   Licensed under the Apache License, Version 2.0 (the "License");
+   you may not use this file except in compliance with the License.
+   You may obtain a copy of the License at
+
+     http://www.apache.org/licenses/LICENSE-2.0
+
+   Unless required by applicable law or agreed to in writing, software
+   distributed under the License is distributed on an "AS IS" BASIS,
+   WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+   See the License for the specific language governing permissions and
+   limitations under the License.

Drivers/CMSIS/Include/cmsis_armcc.h

@@ -0,0 +1,865 @@
+/**************************************************************************//**
+ * @file     cmsis_armcc.h
+ * @brief    CMSIS compiler ARMCC (Arm Compiler 5) header file
+ * @version  V5.0.4
+ * @date     10. January 2018
+ ******************************************************************************/
+/*
+ * Copyright (c) 2009-2018 Arm Limited. All rights reserved.
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the License); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an AS IS BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#ifndef __CMSIS_ARMCC_H
+#define __CMSIS_ARMCC_H
+
+
+#if defined(__ARMCC_VERSION) && (__ARMCC_VERSION < 400677)
+  #error "Please use Arm Compiler Toolchain V4.0.677 or later!"
+#endif
+
+/* CMSIS compiler control architecture macros */
+#if ((defined (__TARGET_ARCH_6_M  ) && (__TARGET_ARCH_6_M   == 1)) || \
+     (defined (__TARGET_ARCH_6S_M ) && (__TARGET_ARCH_6S_M  == 1))   )
+  #define __ARM_ARCH_6M__           1
+#endif
+
+#if (defined (__TARGET_ARCH_7_M ) && (__TARGET_ARCH_7_M  == 1))
+  #define __ARM_ARCH_7M__           1
+#endif
+
+#if (defined (__TARGET_ARCH_7E_M) && (__TARGET_ARCH_7E_M == 1))
+  #define __ARM_ARCH_7EM__          1
+#endif
+
+  /* __ARM_ARCH_8M_BASE__  not applicable */
+  /* __ARM_ARCH_8M_MAIN__  not applicable */
+
+
+/* CMSIS compiler specific defines */
+#ifndef   __ASM
+  #define __ASM                                  __asm
+#endif
+#ifndef   __INLINE
+  #define __INLINE                               __inline
+#endif
+#ifndef   __STATIC_INLINE
+  #define __STATIC_INLINE                        static __inline
+#endif
+#ifndef   __STATIC_FORCEINLINE                 
+  #define __STATIC_FORCEINLINE                   static __forceinline
+#endif           
+#ifndef   __NO_RETURN
+  #define __NO_RETURN                            __declspec(noreturn)
+#endif
+#ifndef   __USED
+  #define __USED                                 __attribute__((used))
+#endif
+#ifndef   __WEAK
+  #define __WEAK                                 __attribute__((weak))
+#endif
+#ifndef   __PACKED
+  #define __PACKED                               __attribute__((packed))
+#endif
+#ifndef   __PACKED_STRUCT
+  #define __PACKED_STRUCT                        __packed struct
+#endif
+#ifndef   __PACKED_UNION
+  #define __PACKED_UNION                         __packed union
+#endif
+#ifndef   __UNALIGNED_UINT32        /* deprecated */
+  #define __UNALIGNED_UINT32(x)                  (*((__packed uint32_t *)(x)))
+#endif
+#ifndef   __UNALIGNED_UINT16_WRITE
+  #define __UNALIGNED_UINT16_WRITE(addr, val)    ((*((__packed uint16_t *)(addr))) = (val))
+#endif
+#ifndef   __UNALIGNED_UINT16_READ
+  #define __UNALIGNED_UINT16_READ(addr)          (*((const __packed uint16_t *)(addr)))
+#endif
+#ifndef   __UNALIGNED_UINT32_WRITE
+  #define __UNALIGNED_UINT32_WRITE(addr, val)    ((*((__packed uint32_t *)(addr))) = (val))
+#endif
+#ifndef   __UNALIGNED_UINT32_READ
+  #define __UNALIGNED_UINT32_READ(addr)          (*((const __packed uint32_t *)(addr)))
+#endif
+#ifndef   __ALIGNED
+  #define __ALIGNED(x)                           __attribute__((aligned(x)))
+#endif
+#ifndef   __RESTRICT
+  #define __RESTRICT                             __restrict
+#endif
+
+/* ###########################  Core Function Access  ########################### */
+/** \ingroup  CMSIS_Core_FunctionInterface
+    \defgroup CMSIS_Core_RegAccFunctions CMSIS Core Register Access Functions
+  @{
+ */
+
+/**
+  \brief   Enable IRQ Interrupts
+  \details Enables IRQ interrupts by clearing the I-bit in the CPSR.
+           Can only be executed in Privileged modes.
+ */
+/* intrinsic void __enable_irq();     */
+
+
+/**
+  \brief   Disable IRQ Interrupts
+  \details Disables IRQ interrupts by setting the I-bit in the CPSR.
+           Can only be executed in Privileged modes.
+ */
+/* intrinsic void __disable_irq();    */
+
+/**
+  \brief   Get Control Register
+  \details Returns the content of the Control Register.
+  \return               Control Register value
+ */
+__STATIC_INLINE uint32_t __get_CONTROL(void)
+{
+  register uint32_t __regControl         __ASM("control");
+  return(__regControl);
+}
+
+
+/**
+  \brief   Set Control Register
+  \details Writes the given value to the Control Register.
+  \param [in]    control  Control Register value to set
+ */
+__STATIC_INLINE void __set_CONTROL(uint32_t control)
+{
+  register uint32_t __regControl         __ASM("control");
+  __regControl = control;
+}
+
+
+/**
+  \brief   Get IPSR Register
+  \details Returns the content of the IPSR Register.
+  \return               IPSR Register value
+ */
+__STATIC_INLINE uint32_t __get_IPSR(void)
+{
+  register uint32_t __regIPSR          __ASM("ipsr");
+  return(__regIPSR);
+}
+
+
+/**
+  \brief   Get APSR Register
+  \details Returns the content of the APSR Register.
+  \return               APSR Register value
+ */
+__STATIC_INLINE uint32_t __get_APSR(void)
+{
+  register uint32_t __regAPSR          __ASM("apsr");
+  return(__regAPSR);
+}
+
+
+/**
+  \brief   Get xPSR Register
+  \details Returns the content of the xPSR Register.
+  \return               xPSR Register value
+ */
+__STATIC_INLINE uint32_t __get_xPSR(void)
+{
+  register uint32_t __regXPSR          __ASM("xpsr");
+  return(__regXPSR);
+}
+
+
+/**
+  \brief   Get Process Stack Pointer
+  \details Returns the current value of the Process Stack Pointer (PSP).
+  \return               PSP Register value
+ */
+__STATIC_INLINE uint32_t __get_PSP(void)
+{
+  register uint32_t __regProcessStackPointer  __ASM("psp");
+  return(__regProcessStackPointer);
+}
+
+
+/**
+  \brief   Set Process Stack Pointer
+  \details Assigns the given value to the Process Stack Pointer (PSP).
+  \param [in]    topOfProcStack  Process Stack Pointer value to set
+ */
+__STATIC_INLINE void __set_PSP(uint32_t topOfProcStack)
+{
+  register uint32_t __regProcessStackPointer  __ASM("psp");
+  __regProcessStackPointer = topOfProcStack;
+}
+
+
+/**
+  \brief   Get Main Stack Pointer
+  \details Returns the current value of the Main Stack Pointer (MSP).
+  \return               MSP Register value
+ */
+__STATIC_INLINE uint32_t __get_MSP(void)
+{
+  register uint32_t __regMainStackPointer     __ASM("msp");
+  return(__regMainStackPointer);
+}
+
+
+/**
+  \brief   Set Main Stack Pointer
+  \details Assigns the given value to the Main Stack Pointer (MSP).
+  \param [in]    topOfMainStack  Main Stack Pointer value to set
+ */
+__STATIC_INLINE void __set_MSP(uint32_t topOfMainStack)
+{
+  register uint32_t __regMainStackPointer     __ASM("msp");
+  __regMainStackPointer = topOfMainStack;
+}
+
+
+/**
+  \brief   Get Priority Mask
+  \details Returns the current state of the priority mask bit from the Priority Mask Register.
+  \return               Priority Mask value
+ */
+__STATIC_INLINE uint32_t __get_PRIMASK(void)
+{
+  register uint32_t __regPriMask         __ASM("primask");
+  return(__regPriMask);
+}
+
+
+/**
+  \brief   Set Priority Mask
+  \details Assigns the given value to the Priority Mask Register.
+  \param [in]    priMask  Priority Mask
+ */
+__STATIC_INLINE void __set_PRIMASK(uint32_t priMask)
+{
+  register uint32_t __regPriMask         __ASM("primask");
+  __regPriMask = (priMask);
+}
+
+
+#if ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__  == 1)) || \
+     (defined (__ARM_ARCH_7EM__) && (__ARM_ARCH_7EM__ == 1))     )
+
+/**
+  \brief   Enable FIQ
+  \details Enables FIQ interrupts by clearing the F-bit in the CPSR.
+           Can only be executed in Privileged modes.
+ */
+#define __enable_fault_irq                __enable_fiq
+
+
+/**
+  \brief   Disable FIQ
+  \details Disables FIQ interrupts by setting the F-bit in the CPSR.
+           Can only be executed in Privileged modes.
+ */
+#define __disable_fault_irq               __disable_fiq
+
+
+/**
+  \brief   Get Base Priority
+  \details Returns the current value of the Base Priority register.
+  \return               Base Priority register value
+ */
+__STATIC_INLINE uint32_t  __get_BASEPRI(void)
+{
+  register uint32_t __regBasePri         __ASM("basepri");
+  return(__regBasePri);
+}
+
+
+/**
+  \brief   Set Base Priority
+  \details Assigns the given value to the Base Priority register.
+  \param [in]    basePri  Base Priority value to set
+ */
+__STATIC_INLINE void __set_BASEPRI(uint32_t basePri)
+{
+  register uint32_t __regBasePri         __ASM("basepri");
+  __regBasePri = (basePri & 0xFFU);
+}
+
+
+/**
+  \brief   Set Base Priority with condition
+  \details Assigns the given value to the Base Priority register only if BASEPRI masking is disabled,
+           or the new value increases the BASEPRI priority level.
+  \param [in]    basePri  Base Priority value to set
+ */
+__STATIC_INLINE void __set_BASEPRI_MAX(uint32_t basePri)
+{
+  register uint32_t __regBasePriMax      __ASM("basepri_max");
+  __regBasePriMax = (basePri & 0xFFU);
+}
+
+
+/**
+  \brief   Get Fault Mask
+  \details Returns the current value of the Fault Mask register.
+  \return               Fault Mask register value
+ */
+__STATIC_INLINE uint32_t __get_FAULTMASK(void)
+{
+  register uint32_t __regFaultMask       __ASM("faultmask");
+  return(__regFaultMask);
+}
+
+
+/**
+  \brief   Set Fault Mask
+  \details Assigns the given value to the Fault Mask register.
+  \param [in]    faultMask  Fault Mask value to set
+ */
+__STATIC_INLINE void __set_FAULTMASK(uint32_t faultMask)
+{
+  register uint32_t __regFaultMask       __ASM("faultmask");
+  __regFaultMask = (faultMask & (uint32_t)1U);
+}
+
+#endif /* ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__  == 1)) || \
+           (defined (__ARM_ARCH_7EM__) && (__ARM_ARCH_7EM__ == 1))     ) */
+
+
+/**
+  \brief   Get FPSCR
+  \details Returns the current value of the Floating Point Status/Control register.
+  \return               Floating Point Status/Control register value
+ */
+__STATIC_INLINE uint32_t __get_FPSCR(void)
+{
+#if ((defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U)) && \
+     (defined (__FPU_USED   ) && (__FPU_USED    == 1U))     )
+  register uint32_t __regfpscr         __ASM("fpscr");
+  return(__regfpscr);
+#else
+   return(0U);
+#endif
+}
+
+
+/**
+  \brief   Set FPSCR
+  \details Assigns the given value to the Floating Point Status/Control register.
+  \param [in]    fpscr  Floating Point Status/Control value to set
+ */
+__STATIC_INLINE void __set_FPSCR(uint32_t fpscr)
+{
+#if ((defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U)) && \
+     (defined (__FPU_USED   ) && (__FPU_USED    == 1U))     )
+  register uint32_t __regfpscr         __ASM("fpscr");
+  __regfpscr = (fpscr);
+#else
+  (void)fpscr;
+#endif
+}
+
+
+/*@} end of CMSIS_Core_RegAccFunctions */
+
+
+/* ##########################  Core Instruction Access  ######################### */
+/** \defgroup CMSIS_Core_InstructionInterface CMSIS Core Instruction Interface
+  Access to dedicated instructions
+  @{
+*/
+
+/**
+  \brief   No Operation
+  \details No Operation does nothing. This instruction can be used for code alignment purposes.
+ */
+#define __NOP                             __nop
+
+
+/**
+  \brief   Wait For Interrupt
+  \details Wait For Interrupt is a hint instruction that suspends execution until one of a number of events occurs.
+ */
+#define __WFI                             __wfi
+
+
+/**
+  \brief   Wait For Event
+  \details Wait For Event is a hint instruction that permits the processor to enter
+           a low-power state until one of a number of events occurs.
+ */
+#define __WFE                             __wfe
+
+
+/**
+  \brief   Send Event
+  \details Send Event is a hint instruction. It causes an event to be signaled to the CPU.
+ */
+#define __SEV                             __sev
+
+
+/**
+  \brief   Instruction Synchronization Barrier
+  \details Instruction Synchronization Barrier flushes the pipeline in the processor,
+           so that all instructions following the ISB are fetched from cache or memory,
+           after the instruction has been completed.
+ */
+#define __ISB() do {\
+                   __schedule_barrier();\
+                   __isb(0xF);\
+                   __schedule_barrier();\
+                } while (0U)
+
+/**
+  \brief   Data Synchronization Barrier
+  \details Acts as a special kind of Data Memory Barrier.
+           It completes when all explicit memory accesses before this instruction complete.
+ */
+#define __DSB() do {\
+                   __schedule_barrier();\
+                   __dsb(0xF);\
+                   __schedule_barrier();\
+                } while (0U)
+
+/**
+  \brief   Data Memory Barrier
+  \details Ensures the apparent order of the explicit memory operations before
+           and after the instruction, without ensuring their completion.
+ */
+#define __DMB() do {\
+                   __schedule_barrier();\
+                   __dmb(0xF);\
+                   __schedule_barrier();\
+                } while (0U)
+
+                  
+/**
+  \brief   Reverse byte order (32 bit)
+  \details Reverses the byte order in unsigned integer value. For example, 0x12345678 becomes 0x78563412.
+  \param [in]    value  Value to reverse
+  \return               Reversed value
+ */
+#define __REV                             __rev
+
+
+/**
+  \brief   Reverse byte order (16 bit)
+  \details Reverses the byte order within each halfword of a word. For example, 0x12345678 becomes 0x34127856.
+  \param [in]    value  Value to reverse
+  \return               Reversed value
+ */
+#ifndef __NO_EMBEDDED_ASM
+__attribute__((section(".rev16_text"))) __STATIC_INLINE __ASM uint32_t __REV16(uint32_t value)
+{
+  rev16 r0, r0
+  bx lr
+}
+#endif
+
+
+/**
+  \brief   Reverse byte order (16 bit)
+  \details Reverses the byte order in a 16-bit value and returns the signed 16-bit result. For example, 0x0080 becomes 0x8000.
+  \param [in]    value  Value to reverse
+  \return               Reversed value
+ */
+#ifndef __NO_EMBEDDED_ASM
+__attribute__((section(".revsh_text"))) __STATIC_INLINE __ASM int16_t __REVSH(int16_t value)
+{
+  revsh r0, r0
+  bx lr
+}
+#endif
+
+
+/**
+  \brief   Rotate Right in unsigned value (32 bit)
+  \details Rotate Right (immediate) provides the value of the contents of a register rotated by a variable number of bits.
+  \param [in]    op1  Value to rotate
+  \param [in]    op2  Number of Bits to rotate
+  \return               Rotated value
+ */
+#define __ROR                             __ror
+
+
+/**
+  \brief   Breakpoint
+  \details Causes the processor to enter Debug state.
+           Debug tools can use this to investigate system state when the instruction at a particular address is reached.
+  \param [in]    value  is ignored by the processor.
+                 If required, a debugger can use it to store additional information about the breakpoint.
+ */
+#define __BKPT(value)                       __breakpoint(value)
+
+
+/**
+  \brief   Reverse bit order of value
+  \details Reverses the bit order of the given value.
+  \param [in]    value  Value to reverse
+  \return               Reversed value
+ */
+#if ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__  == 1)) || \
+     (defined (__ARM_ARCH_7EM__) && (__ARM_ARCH_7EM__ == 1))     )
+  #define __RBIT                          __rbit
+#else
+__attribute__((always_inline)) __STATIC_INLINE uint32_t __RBIT(uint32_t value)
+{
+  uint32_t result;
+  uint32_t s = (4U /*sizeof(v)*/ * 8U) - 1U; /* extra shift needed at end */
+
+  result = value;                      /* r will be reversed bits of v; first get LSB of v */
+  for (value >>= 1U; value != 0U; value >>= 1U)
+  {
+    result <<= 1U;
+    result |= value & 1U;
+    s--;
+  }
+  result <<= s;                        /* shift when v's highest bits are zero */
+  return result;
+}
+#endif
+
+
+/**
+  \brief   Count leading zeros
+  \details Counts the number of leading zeros of a data value.
+  \param [in]  value  Value to count the leading zeros
+  \return             number of leading zeros in value
+ */
+#define __CLZ                             __clz
+
+
+#if ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__  == 1)) || \
+     (defined (__ARM_ARCH_7EM__) && (__ARM_ARCH_7EM__ == 1))     )
+
+/**
+  \brief   LDR Exclusive (8 bit)
+  \details Executes a exclusive LDR instruction for 8 bit value.
+  \param [in]    ptr  Pointer to data
+  \return             value of type uint8_t at (*ptr)
+ */
+#if defined(__ARMCC_VERSION) && (__ARMCC_VERSION < 5060020)
+  #define __LDREXB(ptr)                                                        ((uint8_t ) __ldrex(ptr))
+#else
+  #define __LDREXB(ptr)          _Pragma("push") _Pragma("diag_suppress 3731") ((uint8_t ) __ldrex(ptr))  _Pragma("pop")
+#endif
+
+
+/**
+  \brief   LDR Exclusive (16 bit)
+  \details Executes a exclusive LDR instruction for 16 bit values.
+  \param [in]    ptr  Pointer to data
+  \return        value of type uint16_t at (*ptr)
+ */
+#if defined(__ARMCC_VERSION) && (__ARMCC_VERSION < 5060020)
+  #define __LDREXH(ptr)                                                        ((uint16_t) __ldrex(ptr))
+#else
+  #define __LDREXH(ptr)          _Pragma("push") _Pragma("diag_suppress 3731") ((uint16_t) __ldrex(ptr))  _Pragma("pop")
+#endif
+
+
+/**
+  \brief   LDR Exclusive (32 bit)
+  \details Executes a exclusive LDR instruction for 32 bit values.
+  \param [in]    ptr  Pointer to data
+  \return        value of type uint32_t at (*ptr)
+ */
+#if defined(__ARMCC_VERSION) && (__ARMCC_VERSION < 5060020)
+  #define __LDREXW(ptr)                                                        ((uint32_t ) __ldrex(ptr))
+#else
+  #define __LDREXW(ptr)          _Pragma("push") _Pragma("diag_suppress 3731") ((uint32_t ) __ldrex(ptr))  _Pragma("pop")
+#endif
+
+
+/**
+  \brief   STR Exclusive (8 bit)
+  \details Executes a exclusive STR instruction for 8 bit values.
+  \param [in]  value  Value to store
+  \param [in]    ptr  Pointer to location
+  \return          0  Function succeeded
+  \return          1  Function failed
+ */
+#if defined(__ARMCC_VERSION) && (__ARMCC_VERSION < 5060020)
+  #define __STREXB(value, ptr)                                                 __strex(value, ptr)
+#else
+  #define __STREXB(value, ptr)   _Pragma("push") _Pragma("diag_suppress 3731") __strex(value, ptr)        _Pragma("pop")
+#endif
+
+
+/**
+  \brief   STR Exclusive (16 bit)
+  \details Executes a exclusive STR instruction for 16 bit values.
+  \param [in]  value  Value to store
+  \param [in]    ptr  Pointer to location
+  \return          0  Function succeeded
+  \return          1  Function failed
+ */
+#if defined(__ARMCC_VERSION) && (__ARMCC_VERSION < 5060020)
+  #define __STREXH(value, ptr)                                                 __strex(value, ptr)
+#else
+  #define __STREXH(value, ptr)   _Pragma("push") _Pragma("diag_suppress 3731") __strex(value, ptr)        _Pragma("pop")
+#endif
+
+
+/**
+  \brief   STR Exclusive (32 bit)
+  \details Executes a exclusive STR instruction for 32 bit values.
+  \param [in]  value  Value to store
+  \param [in]    ptr  Pointer to location
+  \return          0  Function succeeded
+  \return          1  Function failed
+ */
+#if defined(__ARMCC_VERSION) && (__ARMCC_VERSION < 5060020)
+  #define __STREXW(value, ptr)                                                 __strex(value, ptr)
+#else
+  #define __STREXW(value, ptr)   _Pragma("push") _Pragma("diag_suppress 3731") __strex(value, ptr)        _Pragma("pop")
+#endif
+
+
+/**
+  \brief   Remove the exclusive lock
+  \details Removes the exclusive lock which is created by LDREX.
+ */
+#define __CLREX                           __clrex
+
+
+/**
+  \brief   Signed Saturate
+  \details Saturates a signed value.
+  \param [in]  value  Value to be saturated
+  \param [in]    sat  Bit position to saturate to (1..32)
+  \return             Saturated value
+ */
+#define __SSAT                            __ssat
+
+
+/**
+  \brief   Unsigned Saturate
+  \details Saturates an unsigned value.
+  \param [in]  value  Value to be saturated
+  \param [in]    sat  Bit position to saturate to (0..31)
+  \return             Saturated value
+ */
+#define __USAT                            __usat
+
+
+/**
+  \brief   Rotate Right with Extend (32 bit)
+  \details Moves each bit of a bitstring right by one bit.
+           The carry input is shifted in at the left end of the bitstring.
+  \param [in]    value  Value to rotate
+  \return               Rotated value
+ */
+#ifndef __NO_EMBEDDED_ASM
+__attribute__((section(".rrx_text"))) __STATIC_INLINE __ASM uint32_t __RRX(uint32_t value)
+{
+  rrx r0, r0
+  bx lr
+}
+#endif
+
+
+/**
+  \brief   LDRT Unprivileged (8 bit)
+  \details Executes a Unprivileged LDRT instruction for 8 bit value.
+  \param [in]    ptr  Pointer to data
+  \return             value of type uint8_t at (*ptr)
+ */
+#define __LDRBT(ptr)                      ((uint8_t )  __ldrt(ptr))
+
+
+/**
+  \brief   LDRT Unprivileged (16 bit)
+  \details Executes a Unprivileged LDRT instruction for 16 bit values.
+  \param [in]    ptr  Pointer to data
+  \return        value of type uint16_t at (*ptr)
+ */
+#define __LDRHT(ptr)                      ((uint16_t)  __ldrt(ptr))
+
+
+/**
+  \brief   LDRT Unprivileged (32 bit)
+  \details Executes a Unprivileged LDRT instruction for 32 bit values.
+  \param [in]    ptr  Pointer to data
+  \return        value of type uint32_t at (*ptr)
+ */
+#define __LDRT(ptr)                       ((uint32_t ) __ldrt(ptr))
+
+
+/**
+  \brief   STRT Unprivileged (8 bit)
+  \details Executes a Unprivileged STRT instruction for 8 bit values.
+  \param [in]  value  Value to store
+  \param [in]    ptr  Pointer to location
+ */
+#define __STRBT(value, ptr)               __strt(value, ptr)
+
+
+/**
+  \brief   STRT Unprivileged (16 bit)
+  \details Executes a Unprivileged STRT instruction for 16 bit values.
+  \param [in]  value  Value to store
+  \param [in]    ptr  Pointer to location
+ */
+#define __STRHT(value, ptr)               __strt(value, ptr)
+
+
+/**
+  \brief   STRT Unprivileged (32 bit)
+  \details Executes a Unprivileged STRT instruction for 32 bit values.
+  \param [in]  value  Value to store
+  \param [in]    ptr  Pointer to location
+ */
+#define __STRT(value, ptr)                __strt(value, ptr)
+
+#else  /* ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__  == 1)) || \
+           (defined (__ARM_ARCH_7EM__) && (__ARM_ARCH_7EM__ == 1))     ) */
+
+/**
+  \brief   Signed Saturate
+  \details Saturates a signed value.
+  \param [in]  value  Value to be saturated
+  \param [in]    sat  Bit position to saturate to (1..32)
+  \return             Saturated value
+ */
+__attribute__((always_inline)) __STATIC_INLINE int32_t __SSAT(int32_t val, uint32_t sat)
+{
+  if ((sat >= 1U) && (sat <= 32U))
+  {
+    const int32_t max = (int32_t)((1U << (sat - 1U)) - 1U);
+    const int32_t min = -1 - max ;
+    if (val > max)
+    {
+      return max;
+    }
+    else if (val < min)
+    {
+      return min;
+    }
+  }
+  return val;
+}
+
+/**
+  \brief   Unsigned Saturate
+  \details Saturates an unsigned value.
+  \param [in]  value  Value to be saturated
+  \param [in]    sat  Bit position to saturate to (0..31)
+  \return             Saturated value
+ */
+__attribute__((always_inline)) __STATIC_INLINE uint32_t __USAT(int32_t val, uint32_t sat)
+{
+  if (sat <= 31U)
+  {
+    const uint32_t max = ((1U << sat) - 1U);
+    if (val > (int32_t)max)
+    {
+      return max;
+    }
+    else if (val < 0)
+    {
+      return 0U;
+    }
+  }
+  return (uint32_t)val;
+}
+
+#endif /* ((defined (__ARM_ARCH_7M__ ) && (__ARM_ARCH_7M__  == 1)) || \
+           (defined (__ARM_ARCH_7EM__) && (__ARM_ARCH_7EM__ == 1))     ) */
+
+/*@}*/ /* end of group CMSIS_Core_InstructionInterface */
+
+
+/* ###################  Compiler specific Intrinsics  ########################### */
+/** \defgroup CMSIS_SIMD_intrinsics CMSIS SIMD Intrinsics
+  Access to dedicated SIMD instructions
+  @{
+*/
+
+#if ((defined (__ARM_ARCH_7EM__) && (__ARM_ARCH_7EM__ == 1))     )
+
+#define __SADD8                           __sadd8
+#define __QADD8                           __qadd8
+#define __SHADD8                          __shadd8
+#define __UADD8                           __uadd8
+#define __UQADD8                          __uqadd8
+#define __UHADD8                          __uhadd8
+#define __SSUB8                           __ssub8
+#define __QSUB8                           __qsub8
+#define __SHSUB8                          __shsub8
+#define __USUB8                           __usub8
+#define __UQSUB8                          __uqsub8
+#define __UHSUB8                          __uhsub8
+#define __SADD16                          __sadd16
+#define __QADD16                          __qadd16
+#define __SHADD16                         __shadd16
+#define __UADD16                          __uadd16
+#define __UQADD16                         __uqadd16
+#define __UHADD16                         __uhadd16
+#define __SSUB16                          __ssub16
+#define __QSUB16                          __qsub16
+#define __SHSUB16                         __shsub16
+#define __USUB16                          __usub16
+#define __UQSUB16                         __uqsub16
+#define __UHSUB16                         __uhsub16
+#define __SASX                            __sasx
+#define __QASX                            __qasx
+#define __SHASX                           __shasx
+#define __UASX                            __uasx
+#define __UQASX                           __uqasx
+#define __UHASX                           __uhasx
+#define __SSAX                            __ssax
+#define __QSAX                            __qsax
+#define __SHSAX                           __shsax
+#define __USAX                            __usax
+#define __UQSAX                           __uqsax
+#define __UHSAX                           __uhsax
+#define __USAD8                           __usad8
+#define __USADA8                          __usada8
+#define __SSAT16                          __ssat16
+#define __USAT16                          __usat16
+#define __UXTB16                          __uxtb16
+#define __UXTAB16                         __uxtab16
+#define __SXTB16                          __sxtb16
+#define __SXTAB16                         __sxtab16
+#define __SMUAD                           __smuad
+#define __SMUADX                          __smuadx
+#define __SMLAD                           __smlad
+#define __SMLADX                          __smladx
+#define __SMLALD                          __smlald
+#define __SMLALDX                         __smlaldx
+#define __SMUSD                           __smusd
+#define __SMUSDX                          __smusdx
+#define __SMLSD                           __smlsd
+#define __SMLSDX                          __smlsdx
+#define __SMLSLD                          __smlsld
+#define __SMLSLDX                         __smlsldx
+#define __SEL                             __sel
+#define __QADD                            __qadd
+#define __QSUB                            __qsub
+
+#define __PKHBT(ARG1,ARG2,ARG3)          ( ((((uint32_t)(ARG1))          ) & 0x0000FFFFUL) |  \
+                                           ((((uint32_t)(ARG2)) << (ARG3)) & 0xFFFF0000UL)  )
+
+#define __PKHTB(ARG1,ARG2,ARG3)          ( ((((uint32_t)(ARG1))          ) & 0xFFFF0000UL) |  \
+                                           ((((uint32_t)(ARG2)) >> (ARG3)) & 0x0000FFFFUL)  )
+
+#define __SMMLA(ARG1,ARG2,ARG3)          ( (int32_t)((((int64_t)(ARG1) * (ARG2)) + \
+                                                      ((int64_t)(ARG3) << 32U)     ) >> 32U))
+
+#endif /* ((defined (__ARM_ARCH_7EM__) && (__ARM_ARCH_7EM__ == 1))     ) */
+/*@} end of group CMSIS_SIMD_intrinsics */
+
+
+#endif /* __CMSIS_ARMCC_H */

Drivers/CMSIS/Include/cmsis_compiler.h

@@ -0,0 +1,266 @@
+/**************************************************************************//**
+ * @file     cmsis_compiler.h
+ * @brief    CMSIS compiler generic header file
+ * @version  V5.0.4
+ * @date     10. January 2018
+ ******************************************************************************/
+/*
+ * Copyright (c) 2009-2018 Arm Limited. All rights reserved.
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the License); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an AS IS BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#ifndef __CMSIS_COMPILER_H
+#define __CMSIS_COMPILER_H
+
+#include <stdint.h>
+
+/*
+ * Arm Compiler 4/5
+ */
+#if   defined ( __CC_ARM )
+  #include "cmsis_armcc.h"
+
+
+/*
+ * Arm Compiler 6 (armclang)
+ */
+#elif defined (__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050)
+  #include "cmsis_armclang.h"
+
+
+/*
+ * GNU Compiler
+ */
+#elif defined ( __GNUC__ )
+  #include "cmsis_gcc.h"
+
+
+/*
+ * IAR Compiler
+ */
+#elif defined ( __ICCARM__ )
+  #include <cmsis_iccarm.h>
+
+
+/*
+ * TI Arm Compiler
+ */
+#elif defined ( __TI_ARM__ )
+  #include <cmsis_ccs.h>
+
+  #ifndef   __ASM
+    #define __ASM                                  __asm
+  #endif
+  #ifndef   __INLINE
+    #define __INLINE                               inline
+  #endif
+  #ifndef   __STATIC_INLINE
+    #define __STATIC_INLINE                        static inline
+  #endif
+  #ifndef   __STATIC_FORCEINLINE
+    #define __STATIC_FORCEINLINE                   __STATIC_INLINE
+  #endif
+  #ifndef   __NO_RETURN
+    #define __NO_RETURN                            __attribute__((noreturn))
+  #endif
+  #ifndef   __USED
+    #define __USED                                 __attribute__((used))
+  #endif
+  #ifndef   __WEAK
+    #define __WEAK                                 __attribute__((weak))
+  #endif
+  #ifndef   __PACKED
+    #define __PACKED                               __attribute__((packed))
+  #endif
+  #ifndef   __PACKED_STRUCT
+    #define __PACKED_STRUCT                        struct __attribute__((packed))
+  #endif
+  #ifndef   __PACKED_UNION
+    #define __PACKED_UNION                         union __attribute__((packed))
+  #endif
+  #ifndef   __UNALIGNED_UINT32        /* deprecated */
+    struct __attribute__((packed)) T_UINT32 { uint32_t v; };
+    #define __UNALIGNED_UINT32(x)                  (((struct T_UINT32 *)(x))->v)
+  #endif
+  #ifndef   __UNALIGNED_UINT16_WRITE
+    __PACKED_STRUCT T_UINT16_WRITE { uint16_t v; };
+    #define __UNALIGNED_UINT16_WRITE(addr, val)    (void)((((struct T_UINT16_WRITE *)(void*)(addr))->v) = (val))
+  #endif
+  #ifndef   __UNALIGNED_UINT16_READ
+    __PACKED_STRUCT T_UINT16_READ { uint16_t v; };
+    #define __UNALIGNED_UINT16_READ(addr)          (((const struct T_UINT16_READ *)(const void *)(addr))->v)
+  #endif
+  #ifndef   __UNALIGNED_UINT32_WRITE
+    __PACKED_STRUCT T_UINT32_WRITE { uint32_t v; };
+    #define __UNALIGNED_UINT32_WRITE(addr, val)    (void)((((struct T_UINT32_WRITE *)(void *)(addr))->v) = (val))
+  #endif
+  #ifndef   __UNALIGNED_UINT32_READ
+    __PACKED_STRUCT T_UINT32_READ { uint32_t v; };
+    #define __UNALIGNED_UINT32_READ(addr)          (((const struct T_UINT32_READ *)(const void *)(addr))->v)
+  #endif
+  #ifndef   __ALIGNED
+    #define __ALIGNED(x)                           __attribute__((aligned(x)))
+  #endif
+  #ifndef   __RESTRICT
+    #warning No compiler specific solution for __RESTRICT. __RESTRICT is ignored.
+    #define __RESTRICT
+  #endif
+
+
+/*
+ * TASKING Compiler
+ */
+#elif defined ( __TASKING__ )
+  /*
+   * The CMSIS functions have been implemented as intrinsics in the compiler.
+   * Please use "carm -?i" to get an up to date list of all intrinsics,
+   * Including the CMSIS ones.
+   */
+
+  #ifndef   __ASM
+    #define __ASM                                  __asm
+  #endif
+  #ifndef   __INLINE
+    #define __INLINE                               inline
+  #endif
+  #ifndef   __STATIC_INLINE
+    #define __STATIC_INLINE                        static inline
+  #endif
+  #ifndef   __STATIC_FORCEINLINE
+    #define __STATIC_FORCEINLINE                   __STATIC_INLINE
+  #endif
+  #ifndef   __NO_RETURN
+    #define __NO_RETURN                            __attribute__((noreturn))
+  #endif
+  #ifndef   __USED
+    #define __USED                                 __attribute__((used))
+  #endif
+  #ifndef   __WEAK
+    #define __WEAK                                 __attribute__((weak))
+  #endif
+  #ifndef   __PACKED
+    #define __PACKED                               __packed__
+  #endif
+  #ifndef   __PACKED_STRUCT
+    #define __PACKED_STRUCT                        struct __packed__
+  #endif
+  #ifndef   __PACKED_UNION
+    #define __PACKED_UNION                         union __packed__
+  #endif
+  #ifndef   __UNALIGNED_UINT32        /* deprecated */
+    struct __packed__ T_UINT32 { uint32_t v; };
+    #define __UNALIGNED_UINT32(x)                  (((struct T_UINT32 *)(x))->v)
+  #endif
+  #ifndef   __UNALIGNED_UINT16_WRITE
+    __PACKED_STRUCT T_UINT16_WRITE { uint16_t v; };
+    #define __UNALIGNED_UINT16_WRITE(addr, val)    (void)((((struct T_UINT16_WRITE *)(void *)(addr))->v) = (val))
+  #endif
+  #ifndef   __UNALIGNED_UINT16_READ
+    __PACKED_STRUCT T_UINT16_READ { uint16_t v; };
+    #define __UNALIGNED_UINT16_READ(addr)          (((const struct T_UINT16_READ *)(const void *)(addr))->v)
+  #endif
+  #ifndef   __UNALIGNED_UINT32_WRITE
+    __PACKED_STRUCT T_UINT32_WRITE { uint32_t v; };
+    #define __UNALIGNED_UINT32_WRITE(addr, val)    (void)((((struct T_UINT32_WRITE *)(void *)(addr))->v) = (val))
+  #endif
+  #ifndef   __UNALIGNED_UINT32_READ
+    __PACKED_STRUCT T_UINT32_READ { uint32_t v; };
+    #define __UNALIGNED_UINT32_READ(addr)          (((const struct T_UINT32_READ *)(const void *)(addr))->v)
+  #endif
+  #ifndef   __ALIGNED
+    #define __ALIGNED(x)              __align(x)
+  #endif
+  #ifndef   __RESTRICT
+    #warning No compiler specific solution for __RESTRICT. __RESTRICT is ignored.
+    #define __RESTRICT
+  #endif
+
+
+/*
+ * COSMIC Compiler
+ */
+#elif defined ( __CSMC__ )
+   #include <cmsis_csm.h>
+
+ #ifndef   __ASM
+    #define __ASM                                  _asm
+  #endif
+  #ifndef   __INLINE
+    #define __INLINE                               inline
+  #endif
+  #ifndef   __STATIC_INLINE
+    #define __STATIC_INLINE                        static inline
+  #endif
+  #ifndef   __STATIC_FORCEINLINE
+    #define __STATIC_FORCEINLINE                   __STATIC_INLINE
+  #endif
+  #ifndef   __NO_RETURN
+    // NO RETURN is automatically detected hence no warning here
+    #define __NO_RETURN
+  #endif
+  #ifndef   __USED
+    #warning No compiler specific solution for __USED. __USED is ignored.
+    #define __USED
+  #endif
+  #ifndef   __WEAK
+    #define __WEAK                                 __weak
+  #endif
+  #ifndef   __PACKED
+    #define __PACKED                               @packed
+  #endif
+  #ifndef   __PACKED_STRUCT
+    #define __PACKED_STRUCT                        @packed struct
+  #endif
+  #ifndef   __PACKED_UNION
+    #define __PACKED_UNION                         @packed union
+  #endif
+  #ifndef   __UNALIGNED_UINT32        /* deprecated */
+    @packed struct T_UINT32 { uint32_t v; };
+    #define __UNALIGNED_UINT32(x)                  (((struct T_UINT32 *)(x))->v)
+  #endif
+  #ifndef   __UNALIGNED_UINT16_WRITE
+    __PACKED_STRUCT T_UINT16_WRITE { uint16_t v; };
+    #define __UNALIGNED_UINT16_WRITE(addr, val)    (void)((((struct T_UINT16_WRITE *)(void *)(addr))->v) = (val))
+  #endif
+  #ifndef   __UNALIGNED_UINT16_READ
+    __PACKED_STRUCT T_UINT16_READ { uint16_t v; };
+    #define __UNALIGNED_UINT16_READ(addr)          (((const struct T_UINT16_READ *)(const void *)(addr))->v)
+  #endif
+  #ifndef   __UNALIGNED_UINT32_WRITE
+    __PACKED_STRUCT T_UINT32_WRITE { uint32_t v; };
+    #define __UNALIGNED_UINT32_WRITE(addr, val)    (void)((((struct T_UINT32_WRITE *)(void *)(addr))->v) = (val))
+  #endif
+  #ifndef   __UNALIGNED_UINT32_READ
+    __PACKED_STRUCT T_UINT32_READ { uint32_t v; };
+    #define __UNALIGNED_UINT32_READ(addr)          (((const struct T_UINT32_READ *)(const void *)(addr))->v)
+  #endif
+  #ifndef   __ALIGNED
+    #warning No compiler specific solution for __ALIGNED. __ALIGNED is ignored.
+    #define __ALIGNED(x)
+  #endif
+  #ifndef   __RESTRICT
+    #warning No compiler specific solution for __RESTRICT. __RESTRICT is ignored.
+    #define __RESTRICT
+  #endif
+
+
+#else
+  #error Unknown compiler.
+#endif
+
+
+#endif /* __CMSIS_COMPILER_H */
+

Drivers/CMSIS/Include/cmsis_iccarm.h

@@ -0,0 +1,935 @@
+/**************************************************************************//**
+ * @file     cmsis_iccarm.h
+ * @brief    CMSIS compiler ICCARM (IAR Compiler for Arm) header file
+ * @version  V5.0.7
+ * @date     19. June 2018
+ ******************************************************************************/
+
+//------------------------------------------------------------------------------
+//
+// Copyright (c) 2017-2018 IAR Systems
+//
+// Licensed under the Apache License, Version 2.0 (the "License")
+// you may not use this file except in compliance with the License.
+// You may obtain a copy of the License at
+//     http://www.apache.org/licenses/LICENSE-2.0
+//
+// Unless required by applicable law or agreed to in writing, software
+// distributed under the License is distributed on an "AS IS" BASIS,
+// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+// See the License for the specific language governing permissions and
+// limitations under the License.
+//
+//------------------------------------------------------------------------------
+
+
+#ifndef __CMSIS_ICCARM_H__
+#define __CMSIS_ICCARM_H__
+
+#ifndef __ICCARM__
+  #error This file should only be compiled by ICCARM
+#endif
+
+#pragma system_include
+
+#define __IAR_FT _Pragma("inline=forced") __intrinsic
+
+#if (__VER__ >= 8000000)
+  #define __ICCARM_V8 1
+#else
+  #define __ICCARM_V8 0
+#endif
+
+#ifndef __ALIGNED
+  #if __ICCARM_V8
+    #define __ALIGNED(x) __attribute__((aligned(x)))
+  #elif (__VER__ >= 7080000)
+    /* Needs IAR language extensions */
+    #define __ALIGNED(x) __attribute__((aligned(x)))
+  #else
+    #warning No compiler specific solution for __ALIGNED.__ALIGNED is ignored.
+    #define __ALIGNED(x)
+  #endif
+#endif
+
+
+/* Define compiler macros for CPU architecture, used in CMSIS 5.
+ */
+#if __ARM_ARCH_6M__ || __ARM_ARCH_7M__ || __ARM_ARCH_7EM__ || __ARM_ARCH_8M_BASE__ || __ARM_ARCH_8M_MAIN__
+/* Macros already defined */
+#else
+  #if defined(__ARM8M_MAINLINE__) || defined(__ARM8EM_MAINLINE__)
+    #define __ARM_ARCH_8M_MAIN__ 1
+  #elif defined(__ARM8M_BASELINE__)
+    #define __ARM_ARCH_8M_BASE__ 1
+  #elif defined(__ARM_ARCH_PROFILE) && __ARM_ARCH_PROFILE == 'M'
+    #if __ARM_ARCH == 6
+      #define __ARM_ARCH_6M__ 1
+    #elif __ARM_ARCH == 7
+      #if __ARM_FEATURE_DSP
+        #define __ARM_ARCH_7EM__ 1
+      #else
+        #define __ARM_ARCH_7M__ 1
+      #endif
+    #endif /* __ARM_ARCH */
+  #endif /* __ARM_ARCH_PROFILE == 'M' */
+#endif
+
+/* Alternativ core deduction for older ICCARM's */
+#if !defined(__ARM_ARCH_6M__) && !defined(__ARM_ARCH_7M__) && !defined(__ARM_ARCH_7EM__) && \
+    !defined(__ARM_ARCH_8M_BASE__) && !defined(__ARM_ARCH_8M_MAIN__)
+  #if defined(__ARM6M__) && (__CORE__ == __ARM6M__)
+    #define __ARM_ARCH_6M__ 1
+  #elif defined(__ARM7M__) && (__CORE__ == __ARM7M__)
+    #define __ARM_ARCH_7M__ 1
+  #elif defined(__ARM7EM__) && (__CORE__ == __ARM7EM__)
+    #define __ARM_ARCH_7EM__  1
+  #elif defined(__ARM8M_BASELINE__) && (__CORE == __ARM8M_BASELINE__)
+    #define __ARM_ARCH_8M_BASE__ 1
+  #elif defined(__ARM8M_MAINLINE__) && (__CORE == __ARM8M_MAINLINE__)
+    #define __ARM_ARCH_8M_MAIN__ 1
+  #elif defined(__ARM8EM_MAINLINE__) && (__CORE == __ARM8EM_MAINLINE__)
+    #define __ARM_ARCH_8M_MAIN__ 1
+  #else
+    #error "Unknown target."
+  #endif
+#endif
+
+
+
+#if defined(__ARM_ARCH_6M__) && __ARM_ARCH_6M__==1
+  #define __IAR_M0_FAMILY  1
+#elif defined(__ARM_ARCH_8M_BASE__) && __ARM_ARCH_8M_BASE__==1
+  #define __IAR_M0_FAMILY  1
+#else
+  #define __IAR_M0_FAMILY  0
+#endif
+
+
+#ifndef __ASM
+  #define __ASM __asm
+#endif
+
+#ifndef __INLINE
+  #define __INLINE inline
+#endif
+
+#ifndef   __NO_RETURN
+  #if __ICCARM_V8
+    #define __NO_RETURN __attribute__((__noreturn__))
+  #else
+    #define __NO_RETURN _Pragma("object_attribute=__noreturn")
+  #endif
+#endif
+
+#ifndef   __PACKED
+  #if __ICCARM_V8
+    #define __PACKED __attribute__((packed, aligned(1)))
+  #else
+    /* Needs IAR language extensions */
+    #define __PACKED __packed
+  #endif
+#endif
+
+#ifndef   __PACKED_STRUCT
+  #if __ICCARM_V8
+    #define __PACKED_STRUCT struct __attribute__((packed, aligned(1)))
+  #else
+    /* Needs IAR language extensions */
+    #define __PACKED_STRUCT __packed struct
+  #endif
+#endif
+
+#ifndef   __PACKED_UNION
+  #if __ICCARM_V8
+    #define __PACKED_UNION union __attribute__((packed, aligned(1)))
+  #else
+    /* Needs IAR language extensions */
+    #define __PACKED_UNION __packed union
+  #endif
+#endif
+
+#ifndef   __RESTRICT
+  #define __RESTRICT            __restrict
+#endif
+
+#ifndef   __STATIC_INLINE
+  #define __STATIC_INLINE       static inline
+#endif
+
+#ifndef   __FORCEINLINE
+  #define __FORCEINLINE         _Pragma("inline=forced")
+#endif
+
+#ifndef   __STATIC_FORCEINLINE
+  #define __STATIC_FORCEINLINE  __FORCEINLINE __STATIC_INLINE
+#endif
+
+#ifndef __UNALIGNED_UINT16_READ
+#pragma language=save
+#pragma language=extended
+__IAR_FT uint16_t __iar_uint16_read(void const *ptr)
+{
+  return *(__packed uint16_t*)(ptr);
+}
+#pragma language=restore
+#define __UNALIGNED_UINT16_READ(PTR) __iar_uint16_read(PTR)
+#endif
+
+
+#ifndef __UNALIGNED_UINT16_WRITE
+#pragma language=save
+#pragma language=extended
+__IAR_FT void __iar_uint16_write(void const *ptr, uint16_t val)
+{
+  *(__packed uint16_t*)(ptr) = val;;
+}
+#pragma language=restore
+#define __UNALIGNED_UINT16_WRITE(PTR,VAL) __iar_uint16_write(PTR,VAL)
+#endif
+
+#ifndef __UNALIGNED_UINT32_READ
+#pragma language=save
+#pragma language=extended
+__IAR_FT uint32_t __iar_uint32_read(void const *ptr)
+{
+  return *(__packed uint32_t*)(ptr);
+}
+#pragma language=restore
+#define __UNALIGNED_UINT32_READ(PTR) __iar_uint32_read(PTR)
+#endif
+
+#ifndef __UNALIGNED_UINT32_WRITE
+#pragma language=save
+#pragma language=extended
+__IAR_FT void __iar_uint32_write(void const *ptr, uint32_t val)
+{
+  *(__packed uint32_t*)(ptr) = val;;
+}
+#pragma language=restore
+#define __UNALIGNED_UINT32_WRITE(PTR,VAL) __iar_uint32_write(PTR,VAL)
+#endif
+
+#ifndef __UNALIGNED_UINT32   /* deprecated */
+#pragma language=save
+#pragma language=extended
+__packed struct  __iar_u32 { uint32_t v; };
+#pragma language=restore
+#define __UNALIGNED_UINT32(PTR) (((struct __iar_u32 *)(PTR))->v)
+#endif
+
+#ifndef   __USED
+  #if __ICCARM_V8
+    #define __USED __attribute__((used))
+  #else
+    #define __USED _Pragma("__root")
+  #endif
+#endif
+
+#ifndef   __WEAK
+  #if __ICCARM_V8
+    #define __WEAK __attribute__((weak))
+  #else
+    #define __WEAK _Pragma("__weak")
+  #endif
+#endif
+
+
+#ifndef __ICCARM_INTRINSICS_VERSION__
+  #define __ICCARM_INTRINSICS_VERSION__  0
+#endif
+
+#if __ICCARM_INTRINSICS_VERSION__ == 2
+
+  #if defined(__CLZ)
+    #undef __CLZ
+  #endif
+  #if defined(__REVSH)
+    #undef __REVSH
+  #endif
+  #if defined(__RBIT)
+    #undef __RBIT
+  #endif
+  #if defined(__SSAT)
+    #undef __SSAT
+  #endif
+  #if defined(__USAT)
+    #undef __USAT
+  #endif
+
+  #include "iccarm_builtin.h"
+
+  #define __disable_fault_irq __iar_builtin_disable_fiq
+  #define __disable_irq       __iar_builtin_disable_interrupt
+  #define __enable_fault_irq  __iar_builtin_enable_fiq
+  #define __enable_irq        __iar_builtin_enable_interrupt
+  #define __arm_rsr           __iar_builtin_rsr
+  #define __arm_wsr           __iar_builtin_wsr
+
+
+  #define __get_APSR()                (__arm_rsr("APSR"))
+  #define __get_BASEPRI()             (__arm_rsr("BASEPRI"))
+  #define __get_CONTROL()             (__arm_rsr("CONTROL"))
+  #define __get_FAULTMASK()           (__arm_rsr("FAULTMASK"))
+
+  #if ((defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U)) && \
+       (defined (__FPU_USED   ) && (__FPU_USED    == 1U))     )
+    #define __get_FPSCR()             (__arm_rsr("FPSCR"))
+    #define __set_FPSCR(VALUE)        (__arm_wsr("FPSCR", (VALUE)))
+  #else
+    #define __get_FPSCR()             ( 0 )
+    #define __set_FPSCR(VALUE)        ((void)VALUE)
+  #endif
+
+  #define __get_IPSR()                (__arm_rsr("IPSR"))
+  #define __get_MSP()                 (__arm_rsr("MSP"))
+  #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+       (!defined (__ARM_FEATURE_CMSE) || (__ARM_FEATURE_CMSE < 3)))
+    // without main extensions, the non-secure MSPLIM is RAZ/WI
+    #define __get_MSPLIM()            (0U)
+  #else
+    #define __get_MSPLIM()            (__arm_rsr("MSPLIM"))
+  #endif
+  #define __get_PRIMASK()             (__arm_rsr("PRIMASK"))
+  #define __get_PSP()                 (__arm_rsr("PSP"))
+
+  #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+       (!defined (__ARM_FEATURE_CMSE) || (__ARM_FEATURE_CMSE < 3)))
+    // without main extensions, the non-secure PSPLIM is RAZ/WI
+    #define __get_PSPLIM()            (0U)
+  #else
+    #define __get_PSPLIM()            (__arm_rsr("PSPLIM"))
+  #endif
+
+  #define __get_xPSR()                (__arm_rsr("xPSR"))
+
+  #define __set_BASEPRI(VALUE)        (__arm_wsr("BASEPRI", (VALUE)))
+  #define __set_BASEPRI_MAX(VALUE)    (__arm_wsr("BASEPRI_MAX", (VALUE)))
+  #define __set_CONTROL(VALUE)        (__arm_wsr("CONTROL", (VALUE)))
+  #define __set_FAULTMASK(VALUE)      (__arm_wsr("FAULTMASK", (VALUE)))
+  #define __set_MSP(VALUE)            (__arm_wsr("MSP", (VALUE)))
+
+  #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+       (!defined (__ARM_FEATURE_CMSE) || (__ARM_FEATURE_CMSE < 3)))
+    // without main extensions, the non-secure MSPLIM is RAZ/WI
+    #define __set_MSPLIM(VALUE)       ((void)(VALUE))
+  #else
+    #define __set_MSPLIM(VALUE)       (__arm_wsr("MSPLIM", (VALUE)))
+  #endif
+  #define __set_PRIMASK(VALUE)        (__arm_wsr("PRIMASK", (VALUE)))
+  #define __set_PSP(VALUE)            (__arm_wsr("PSP", (VALUE)))
+  #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+       (!defined (__ARM_FEATURE_CMSE) || (__ARM_FEATURE_CMSE < 3)))
+    // without main extensions, the non-secure PSPLIM is RAZ/WI
+    #define __set_PSPLIM(VALUE)       ((void)(VALUE))
+  #else
+    #define __set_PSPLIM(VALUE)       (__arm_wsr("PSPLIM", (VALUE)))
+  #endif
+
+  #define __TZ_get_CONTROL_NS()       (__arm_rsr("CONTROL_NS"))
+  #define __TZ_set_CONTROL_NS(VALUE)  (__arm_wsr("CONTROL_NS", (VALUE)))
+  #define __TZ_get_PSP_NS()           (__arm_rsr("PSP_NS"))
+  #define __TZ_set_PSP_NS(VALUE)      (__arm_wsr("PSP_NS", (VALUE)))
+  #define __TZ_get_MSP_NS()           (__arm_rsr("MSP_NS"))
+  #define __TZ_set_MSP_NS(VALUE)      (__arm_wsr("MSP_NS", (VALUE)))
+  #define __TZ_get_SP_NS()            (__arm_rsr("SP_NS"))
+  #define __TZ_set_SP_NS(VALUE)       (__arm_wsr("SP_NS", (VALUE)))
+  #define __TZ_get_PRIMASK_NS()       (__arm_rsr("PRIMASK_NS"))
+  #define __TZ_set_PRIMASK_NS(VALUE)  (__arm_wsr("PRIMASK_NS", (VALUE)))
+  #define __TZ_get_BASEPRI_NS()       (__arm_rsr("BASEPRI_NS"))
+  #define __TZ_set_BASEPRI_NS(VALUE)  (__arm_wsr("BASEPRI_NS", (VALUE)))
+  #define __TZ_get_FAULTMASK_NS()     (__arm_rsr("FAULTMASK_NS"))
+  #define __TZ_set_FAULTMASK_NS(VALUE)(__arm_wsr("FAULTMASK_NS", (VALUE)))
+
+  #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+       (!defined (__ARM_FEATURE_CMSE) || (__ARM_FEATURE_CMSE < 3)))
+    // without main extensions, the non-secure PSPLIM is RAZ/WI
+    #define __TZ_get_PSPLIM_NS()      (0U)
+    #define __TZ_set_PSPLIM_NS(VALUE) ((void)(VALUE))
+  #else
+    #define __TZ_get_PSPLIM_NS()      (__arm_rsr("PSPLIM_NS"))
+    #define __TZ_set_PSPLIM_NS(VALUE) (__arm_wsr("PSPLIM_NS", (VALUE)))
+  #endif
+
+  #define __TZ_get_MSPLIM_NS()        (__arm_rsr("MSPLIM_NS"))
+  #define __TZ_set_MSPLIM_NS(VALUE)   (__arm_wsr("MSPLIM_NS", (VALUE)))
+
+  #define __NOP     __iar_builtin_no_operation
+
+  #define __CLZ     __iar_builtin_CLZ
+  #define __CLREX   __iar_builtin_CLREX
+
+  #define __DMB     __iar_builtin_DMB
+  #define __DSB     __iar_builtin_DSB
+  #define __ISB     __iar_builtin_ISB
+
+  #define __LDREXB  __iar_builtin_LDREXB
+  #define __LDREXH  __iar_builtin_LDREXH
+  #define __LDREXW  __iar_builtin_LDREX
+
+  #define __RBIT    __iar_builtin_RBIT
+  #define __REV     __iar_builtin_REV
+  #define __REV16   __iar_builtin_REV16
+
+  __IAR_FT int16_t __REVSH(int16_t val)
+  {
+    return (int16_t) __iar_builtin_REVSH(val);
+  }
+
+  #define __ROR     __iar_builtin_ROR
+  #define __RRX     __iar_builtin_RRX
+
+  #define __SEV     __iar_builtin_SEV
+
+  #if !__IAR_M0_FAMILY
+    #define __SSAT    __iar_builtin_SSAT
+  #endif
+
+  #define __STREXB  __iar_builtin_STREXB
+  #define __STREXH  __iar_builtin_STREXH
+  #define __STREXW  __iar_builtin_STREX
+
+  #if !__IAR_M0_FAMILY
+    #define __USAT    __iar_builtin_USAT
+  #endif
+
+  #define __WFE     __iar_builtin_WFE
+  #define __WFI     __iar_builtin_WFI
+
+  #if __ARM_MEDIA__
+    #define __SADD8   __iar_builtin_SADD8
+    #define __QADD8   __iar_builtin_QADD8
+    #define __SHADD8  __iar_builtin_SHADD8
+    #define __UADD8   __iar_builtin_UADD8
+    #define __UQADD8  __iar_builtin_UQADD8
+    #define __UHADD8  __iar_builtin_UHADD8
+    #define __SSUB8   __iar_builtin_SSUB8
+    #define __QSUB8   __iar_builtin_QSUB8
+    #define __SHSUB8  __iar_builtin_SHSUB8
+    #define __USUB8   __iar_builtin_USUB8
+    #define __UQSUB8  __iar_builtin_UQSUB8
+    #define __UHSUB8  __iar_builtin_UHSUB8
+    #define __SADD16  __iar_builtin_SADD16
+    #define __QADD16  __iar_builtin_QADD16
+    #define __SHADD16 __iar_builtin_SHADD16
+    #define __UADD16  __iar_builtin_UADD16
+    #define __UQADD16 __iar_builtin_UQADD16
+    #define __UHADD16 __iar_builtin_UHADD16
+    #define __SSUB16  __iar_builtin_SSUB16
+    #define __QSUB16  __iar_builtin_QSUB16
+    #define __SHSUB16 __iar_builtin_SHSUB16
+    #define __USUB16  __iar_builtin_USUB16
+    #define __UQSUB16 __iar_builtin_UQSUB16
+    #define __UHSUB16 __iar_builtin_UHSUB16
+    #define __SASX    __iar_builtin_SASX
+    #define __QASX    __iar_builtin_QASX
+    #define __SHASX   __iar_builtin_SHASX
+    #define __UASX    __iar_builtin_UASX
+    #define __UQASX   __iar_builtin_UQASX
+    #define __UHASX   __iar_builtin_UHASX
+    #define __SSAX    __iar_builtin_SSAX
+    #define __QSAX    __iar_builtin_QSAX
+    #define __SHSAX   __iar_builtin_SHSAX
+    #define __USAX    __iar_builtin_USAX
+    #define __UQSAX   __iar_builtin_UQSAX
+    #define __UHSAX   __iar_builtin_UHSAX
+    #define __USAD8   __iar_builtin_USAD8
+    #define __USADA8  __iar_builtin_USADA8
+    #define __SSAT16  __iar_builtin_SSAT16
+    #define __USAT16  __iar_builtin_USAT16
+    #define __UXTB16  __iar_builtin_UXTB16
+    #define __UXTAB16 __iar_builtin_UXTAB16
+    #define __SXTB16  __iar_builtin_SXTB16
+    #define __SXTAB16 __iar_builtin_SXTAB16
+    #define __SMUAD   __iar_builtin_SMUAD
+    #define __SMUADX  __iar_builtin_SMUADX
+    #define __SMMLA   __iar_builtin_SMMLA
+    #define __SMLAD   __iar_builtin_SMLAD
+    #define __SMLADX  __iar_builtin_SMLADX
+    #define __SMLALD  __iar_builtin_SMLALD
+    #define __SMLALDX __iar_builtin_SMLALDX
+    #define __SMUSD   __iar_builtin_SMUSD
+    #define __SMUSDX  __iar_builtin_SMUSDX
+    #define __SMLSD   __iar_builtin_SMLSD
+    #define __SMLSDX  __iar_builtin_SMLSDX
+    #define __SMLSLD  __iar_builtin_SMLSLD
+    #define __SMLSLDX __iar_builtin_SMLSLDX
+    #define __SEL     __iar_builtin_SEL
+    #define __QADD    __iar_builtin_QADD
+    #define __QSUB    __iar_builtin_QSUB
+    #define __PKHBT   __iar_builtin_PKHBT
+    #define __PKHTB   __iar_builtin_PKHTB
+  #endif
+
+#else /* __ICCARM_INTRINSICS_VERSION__ == 2 */
+
+  #if __IAR_M0_FAMILY
+   /* Avoid clash between intrinsics.h and arm_math.h when compiling for Cortex-M0. */
+    #define __CLZ  __cmsis_iar_clz_not_active
+    #define __SSAT __cmsis_iar_ssat_not_active
+    #define __USAT __cmsis_iar_usat_not_active
+    #define __RBIT __cmsis_iar_rbit_not_active
+    #define __get_APSR  __cmsis_iar_get_APSR_not_active
+  #endif
+
+
+  #if (!((defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U)) && \
+         (defined (__FPU_USED   ) && (__FPU_USED    == 1U))     ))
+    #define __get_FPSCR __cmsis_iar_get_FPSR_not_active
+    #define __set_FPSCR __cmsis_iar_set_FPSR_not_active
+  #endif
+
+  #ifdef __INTRINSICS_INCLUDED
+  #error intrinsics.h is already included previously!
+  #endif
+
+  #include <intrinsics.h>
+
+  #if __IAR_M0_FAMILY
+   /* Avoid clash between intrinsics.h and arm_math.h when compiling for Cortex-M0. */
+    #undef __CLZ
+    #undef __SSAT
+    #undef __USAT
+    #undef __RBIT
+    #undef __get_APSR
+
+    __STATIC_INLINE uint8_t __CLZ(uint32_t data)
+    {
+      if (data == 0U) { return 32U; }
+
+      uint32_t count = 0U;
+      uint32_t mask = 0x80000000U;
+
+      while ((data & mask) == 0U)
+      {
+        count += 1U;
+        mask = mask >> 1U;
+      }
+      return count;
+    }
+
+    __STATIC_INLINE uint32_t __RBIT(uint32_t v)
+    {
+      uint8_t sc = 31U;
+      uint32_t r = v;
+      for (v >>= 1U; v; v >>= 1U)
+      {
+        r <<= 1U;
+        r |= v & 1U;
+        sc--;
+      }
+      return (r << sc);
+    }
+
+    __STATIC_INLINE  uint32_t __get_APSR(void)
+    {
+      uint32_t res;
+      __asm("MRS      %0,APSR" : "=r" (res));
+      return res;
+    }
+
+  #endif
+
+  #if (!((defined (__FPU_PRESENT) && (__FPU_PRESENT == 1U)) && \
+         (defined (__FPU_USED   ) && (__FPU_USED    == 1U))     ))
+    #undef __get_FPSCR
+    #undef __set_FPSCR
+    #define __get_FPSCR()       (0)
+    #define __set_FPSCR(VALUE)  ((void)VALUE)
+  #endif
+
+  #pragma diag_suppress=Pe940
+  #pragma diag_suppress=Pe177
+
+  #define __enable_irq    __enable_interrupt
+  #define __disable_irq   __disable_interrupt
+  #define __NOP           __no_operation
+
+  #define __get_xPSR      __get_PSR
+
+  #if (!defined(__ARM_ARCH_6M__) || __ARM_ARCH_6M__==0)
+
+    __IAR_FT uint32_t __LDREXW(uint32_t volatile *ptr)
+    {
+      return __LDREX((unsigned long *)ptr);
+    }
+
+    __IAR_FT uint32_t __STREXW(uint32_t value, uint32_t volatile *ptr)
+    {
+      return __STREX(value, (unsigned long *)ptr);
+    }
+  #endif
+
+
+  /* __CORTEX_M is defined in core_cm0.h, core_cm3.h and core_cm4.h. */
+  #if (__CORTEX_M >= 0x03)
+
+    __IAR_FT uint32_t __RRX(uint32_t value)
+    {
+      uint32_t result;
+      __ASM("RRX      %0, %1" : "=r"(result) : "r" (value) : "cc");
+      return(result);
+    }
+
+    __IAR_FT void __set_BASEPRI_MAX(uint32_t value)
+    {
+      __asm volatile("MSR      BASEPRI_MAX,%0"::"r" (value));
+    }
+
+
+    #define __enable_fault_irq  __enable_fiq
+    #define __disable_fault_irq __disable_fiq
+
+
+  #endif /* (__CORTEX_M >= 0x03) */
+
+  __IAR_FT uint32_t __ROR(uint32_t op1, uint32_t op2)
+  {
+    return (op1 >> op2) | (op1 << ((sizeof(op1)*8)-op2));
+  }
+
+  #if ((defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) || \
+       (defined (__ARM_ARCH_8M_BASE__ ) && (__ARM_ARCH_8M_BASE__ == 1))    )
+
+   __IAR_FT uint32_t __get_MSPLIM(void)
+    {
+      uint32_t res;
+    #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+         (!defined (__ARM_FEATURE_CMSE  ) || (__ARM_FEATURE_CMSE   < 3)))
+      // without main extensions, the non-secure MSPLIM is RAZ/WI
+      res = 0U;
+    #else
+      __asm volatile("MRS      %0,MSPLIM" : "=r" (res));
+    #endif
+      return res;
+    }
+
+    __IAR_FT void   __set_MSPLIM(uint32_t value)
+    {
+    #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+         (!defined (__ARM_FEATURE_CMSE  ) || (__ARM_FEATURE_CMSE   < 3)))
+      // without main extensions, the non-secure MSPLIM is RAZ/WI
+      (void)value;
+    #else
+      __asm volatile("MSR      MSPLIM,%0" :: "r" (value));
+    #endif
+    }
+
+    __IAR_FT uint32_t __get_PSPLIM(void)
+    {
+      uint32_t res;
+    #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+         (!defined (__ARM_FEATURE_CMSE  ) || (__ARM_FEATURE_CMSE   < 3)))
+      // without main extensions, the non-secure PSPLIM is RAZ/WI
+      res = 0U;
+    #else
+      __asm volatile("MRS      %0,PSPLIM" : "=r" (res));
+    #endif
+      return res;
+    }
+
+    __IAR_FT void   __set_PSPLIM(uint32_t value)
+    {
+    #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+         (!defined (__ARM_FEATURE_CMSE  ) || (__ARM_FEATURE_CMSE   < 3)))
+      // without main extensions, the non-secure PSPLIM is RAZ/WI
+      (void)value;
+    #else
+      __asm volatile("MSR      PSPLIM,%0" :: "r" (value));
+    #endif
+    }
+
+    __IAR_FT uint32_t __TZ_get_CONTROL_NS(void)
+    {
+      uint32_t res;
+      __asm volatile("MRS      %0,CONTROL_NS" : "=r" (res));
+      return res;
+    }
+
+    __IAR_FT void   __TZ_set_CONTROL_NS(uint32_t value)
+    {
+      __asm volatile("MSR      CONTROL_NS,%0" :: "r" (value));
+    }
+
+    __IAR_FT uint32_t   __TZ_get_PSP_NS(void)
+    {
+      uint32_t res;
+      __asm volatile("MRS      %0,PSP_NS" : "=r" (res));
+      return res;
+    }
+
+    __IAR_FT void   __TZ_set_PSP_NS(uint32_t value)
+    {
+      __asm volatile("MSR      PSP_NS,%0" :: "r" (value));
+    }
+
+    __IAR_FT uint32_t   __TZ_get_MSP_NS(void)
+    {
+      uint32_t res;
+      __asm volatile("MRS      %0,MSP_NS" : "=r" (res));
+      return res;
+    }
+
+    __IAR_FT void   __TZ_set_MSP_NS(uint32_t value)
+    {
+      __asm volatile("MSR      MSP_NS,%0" :: "r" (value));
+    }
+
+    __IAR_FT uint32_t   __TZ_get_SP_NS(void)
+    {
+      uint32_t res;
+      __asm volatile("MRS      %0,SP_NS" : "=r" (res));
+      return res;
+    }
+    __IAR_FT void   __TZ_set_SP_NS(uint32_t value)
+    {
+      __asm volatile("MSR      SP_NS,%0" :: "r" (value));
+    }
+
+    __IAR_FT uint32_t   __TZ_get_PRIMASK_NS(void)
+    {
+      uint32_t res;
+      __asm volatile("MRS      %0,PRIMASK_NS" : "=r" (res));
+      return res;
+    }
+
+    __IAR_FT void   __TZ_set_PRIMASK_NS(uint32_t value)
+    {
+      __asm volatile("MSR      PRIMASK_NS,%0" :: "r" (value));
+    }
+
+    __IAR_FT uint32_t   __TZ_get_BASEPRI_NS(void)
+    {
+      uint32_t res;
+      __asm volatile("MRS      %0,BASEPRI_NS" : "=r" (res));
+      return res;
+    }
+
+    __IAR_FT void   __TZ_set_BASEPRI_NS(uint32_t value)
+    {
+      __asm volatile("MSR      BASEPRI_NS,%0" :: "r" (value));
+    }
+
+    __IAR_FT uint32_t   __TZ_get_FAULTMASK_NS(void)
+    {
+      uint32_t res;
+      __asm volatile("MRS      %0,FAULTMASK_NS" : "=r" (res));
+      return res;
+    }
+
+    __IAR_FT void   __TZ_set_FAULTMASK_NS(uint32_t value)
+    {
+      __asm volatile("MSR      FAULTMASK_NS,%0" :: "r" (value));
+    }
+
+    __IAR_FT uint32_t   __TZ_get_PSPLIM_NS(void)
+    {
+      uint32_t res;
+    #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+         (!defined (__ARM_FEATURE_CMSE  ) || (__ARM_FEATURE_CMSE   < 3)))
+      // without main extensions, the non-secure PSPLIM is RAZ/WI
+      res = 0U;
+    #else
+      __asm volatile("MRS      %0,PSPLIM_NS" : "=r" (res));
+    #endif
+      return res;
+    }
+
+    __IAR_FT void   __TZ_set_PSPLIM_NS(uint32_t value)
+    {
+    #if (!(defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) && \
+         (!defined (__ARM_FEATURE_CMSE  ) || (__ARM_FEATURE_CMSE   < 3)))
+      // without main extensions, the non-secure PSPLIM is RAZ/WI
+      (void)value;
+    #else
+      __asm volatile("MSR      PSPLIM_NS,%0" :: "r" (value));
+    #endif
+    }
+
+    __IAR_FT uint32_t   __TZ_get_MSPLIM_NS(void)
+    {
+      uint32_t res;
+      __asm volatile("MRS      %0,MSPLIM_NS" : "=r" (res));
+      return res;
+    }
+
+    __IAR_FT void   __TZ_set_MSPLIM_NS(uint32_t value)
+    {
+      __asm volatile("MSR      MSPLIM_NS,%0" :: "r" (value));
+    }
+
+  #endif /* __ARM_ARCH_8M_MAIN__ or __ARM_ARCH_8M_BASE__ */
+
+#endif   /* __ICCARM_INTRINSICS_VERSION__ == 2 */
+
+#define __BKPT(value)    __asm volatile ("BKPT     %0" : : "i"(value))
+
+#if __IAR_M0_FAMILY
+  __STATIC_INLINE int32_t __SSAT(int32_t val, uint32_t sat)
+  {
+    if ((sat >= 1U) && (sat <= 32U))
+    {
+      const int32_t max = (int32_t)((1U << (sat - 1U)) - 1U);
+      const int32_t min = -1 - max ;
+      if (val > max)
+      {
+        return max;
+      }
+      else if (val < min)
+      {
+        return min;
+      }
+    }
+    return val;
+  }
+
+  __STATIC_INLINE uint32_t __USAT(int32_t val, uint32_t sat)
+  {
+    if (sat <= 31U)
+    {
+      const uint32_t max = ((1U << sat) - 1U);
+      if (val > (int32_t)max)
+      {
+        return max;
+      }
+      else if (val < 0)
+      {
+        return 0U;
+      }
+    }
+    return (uint32_t)val;
+  }
+#endif
+
+#if (__CORTEX_M >= 0x03)   /* __CORTEX_M is defined in core_cm0.h, core_cm3.h and core_cm4.h. */
+
+  __IAR_FT uint8_t __LDRBT(volatile uint8_t *addr)
+  {
+    uint32_t res;
+    __ASM("LDRBT %0, [%1]" : "=r" (res) : "r" (addr) : "memory");
+    return ((uint8_t)res);
+  }
+
+  __IAR_FT uint16_t __LDRHT(volatile uint16_t *addr)
+  {
+    uint32_t res;
+    __ASM("LDRHT %0, [%1]" : "=r" (res) : "r" (addr) : "memory");
+    return ((uint16_t)res);
+  }
+
+  __IAR_FT uint32_t __LDRT(volatile uint32_t *addr)
+  {
+    uint32_t res;
+    __ASM("LDRT %0, [%1]" : "=r" (res) : "r" (addr) : "memory");
+    return res;
+  }
+
+  __IAR_FT void __STRBT(uint8_t value, volatile uint8_t *addr)
+  {
+    __ASM("STRBT %1, [%0]" : : "r" (addr), "r" ((uint32_t)value) : "memory");
+  }
+
+  __IAR_FT void __STRHT(uint16_t value, volatile uint16_t *addr)
+  {
+    __ASM("STRHT %1, [%0]" : : "r" (addr), "r" ((uint32_t)value) : "memory");
+  }
+
+  __IAR_FT void __STRT(uint32_t value, volatile uint32_t *addr)
+  {
+    __ASM("STRT %1, [%0]" : : "r" (addr), "r" (value) : "memory");
+  }
+
+#endif /* (__CORTEX_M >= 0x03) */
+
+#if ((defined (__ARM_ARCH_8M_MAIN__ ) && (__ARM_ARCH_8M_MAIN__ == 1)) || \
+     (defined (__ARM_ARCH_8M_BASE__ ) && (__ARM_ARCH_8M_BASE__ == 1))    )
+
+
+  __IAR_FT uint8_t __LDAB(volatile uint8_t *ptr)
+  {
+    uint32_t res;
+    __ASM volatile ("LDAB %0, [%1]" : "=r" (res) : "r" (ptr) : "memory");
+    return ((uint8_t)res);
+  }
+
+  __IAR_FT uint16_t __LDAH(volatile uint16_t *ptr)
+  {
+    uint32_t res;
+    __ASM volatile ("LDAH %0, [%1]" : "=r" (res) : "r" (ptr) : "memory");
+    return ((uint16_t)res);
+  }
+
+  __IAR_FT uint32_t __LDA(volatile uint32_t *ptr)
+  {
+    uint32_t res;
+    __ASM volatile ("LDA %0, [%1]" : "=r" (res) : "r" (ptr) : "memory");
+    return res;
+  }
+
+  __IAR_FT void __STLB(uint8_t value, volatile uint8_t *ptr)
+  {
+    __ASM volatile ("STLB %1, [%0]" :: "r" (ptr), "r" (value) : "memory");
+  }
+
+  __IAR_FT void __STLH(uint16_t value, volatile uint16_t *ptr)
+  {
+    __ASM volatile ("STLH %1, [%0]" :: "r" (ptr), "r" (value) : "memory");
+  }
+
+  __IAR_FT void __STL(uint32_t value, volatile uint32_t *ptr)
+  {
+    __ASM volatile ("STL %1, [%0]" :: "r" (ptr), "r" (value) : "memory");
+  }
+
+  __IAR_FT uint8_t __LDAEXB(volatile uint8_t *ptr)
+  {
+    uint32_t res;
+    __ASM volatile ("LDAEXB %0, [%1]" : "=r" (res) : "r" (ptr) : "memory");
+    return ((uint8_t)res);
+  }
+
+  __IAR_FT uint16_t __LDAEXH(volatile uint16_t *ptr)
+  {
+    uint32_t res;
+    __ASM volatile ("LDAEXH %0, [%1]" : "=r" (res) : "r" (ptr) : "memory");
+    return ((uint16_t)res);
+  }
+
+  __IAR_FT uint32_t __LDAEX(volatile uint32_t *ptr)
+  {
+    uint32_t res;
+    __ASM volatile ("LDAEX %0, [%1]" : "=r" (res) : "r" (ptr) : "memory");
+    return res;
+  }
+
+  __IAR_FT uint32_t __STLEXB(uint8_t value, volatile uint8_t *ptr)
+  {
+    uint32_t res;
+    __ASM volatile ("STLEXB %0, %2, [%1]" : "=r" (res) : "r" (ptr), "r" (value) : "memory");
+    return res;
+  }
+
+  __IAR_FT uint32_t __STLEXH(uint16_t value, volatile uint16_t *ptr)
+  {
+    uint32_t res;
+    __ASM volatile ("STLEXH %0, %2, [%1]" : "=r" (res) : "r" (ptr), "r" (value) : "memory");
+    return res;
+  }
+
+  __IAR_FT uint32_t __STLEX(uint32_t value, volatile uint32_t *ptr)
+  {
+    uint32_t res;
+    __ASM volatile ("STLEX %0, %2, [%1]" : "=r" (res) : "r" (ptr), "r" (value) : "memory");
+    return res;
+  }
+
+#endif /* __ARM_ARCH_8M_MAIN__ or __ARM_ARCH_8M_BASE__ */
+
+#undef __IAR_FT
+#undef __IAR_M0_FAMILY
+#undef __ICCARM_V8
+
+#pragma diag_default=Pe940
+#pragma diag_default=Pe177
+
+#endif /* __CMSIS_ICCARM_H__ */

Drivers/CMSIS/Include/cmsis_version.h

@@ -0,0 +1,39 @@
+/**************************************************************************//**
+ * @file     cmsis_version.h
+ * @brief    CMSIS Core(M) Version definitions
+ * @version  V5.0.2
+ * @date     19. April 2017
+ ******************************************************************************/
+/*
+ * Copyright (c) 2009-2017 ARM Limited. All rights reserved.
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the License); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an AS IS BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#if   defined ( __ICCARM__ )
+  #pragma system_include         /* treat file as system include file for MISRA check */
+#elif defined (__clang__)
+  #pragma clang system_header   /* treat file as system include file */
+#endif
+
+#ifndef __CMSIS_VERSION_H
+#define __CMSIS_VERSION_H
+
+/*  CMSIS Version definitions */
+#define __CM_CMSIS_VERSION_MAIN  ( 5U)                                      /*!< [31:16] CMSIS Core(M) main version */
+#define __CM_CMSIS_VERSION_SUB   ( 1U)                                      /*!< [15:0]  CMSIS Core(M) sub version */
+#define __CM_CMSIS_VERSION       ((__CM_CMSIS_VERSION_MAIN << 16U) | \
+                                   __CM_CMSIS_VERSION_SUB           )       /*!< CMSIS Core(M) version number */
+#endif

Drivers/CMSIS/Include/core_cm0.h

@@ -0,0 +1,949 @@
+/**************************************************************************//**
+ * @file     core_cm0.h
+ * @brief    CMSIS Cortex-M0 Core Peripheral Access Layer Header File
+ * @version  V5.0.5
+ * @date     28. May 2018
+ ******************************************************************************/
+/*
+ * Copyright (c) 2009-2018 Arm Limited. All rights reserved.
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the License); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an AS IS BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#if   defined ( __ICCARM__ )
+  #pragma system_include         /* treat file as system include file for MISRA check */
+#elif defined (__clang__)
+  #pragma clang system_header   /* treat file as system include file */
+#endif
+
+#ifndef __CORE_CM0_H_GENERIC
+#define __CORE_CM0_H_GENERIC
+
+#include <stdint.h>
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/**
+  \page CMSIS_MISRA_Exceptions  MISRA-C:2004 Compliance Exceptions
+  CMSIS violates the following MISRA-C:2004 rules:
+
+   \li Required Rule 8.5, object/function definition in header file.<br>
+     Function definitions in header files are used to allow 'inlining'.
+
+   \li Required Rule 18.4, declaration of union type or object of union type: '{...}'.<br>
+     Unions are used for effective representation of core registers.
+
+   \li Advisory Rule 19.7, Function-like macro defined.<br>
+     Function-like macros are used to allow more efficient code.
+ */
+
+
+/*******************************************************************************
+ *                 CMSIS definitions
+ ******************************************************************************/
+/**
+  \ingroup Cortex_M0
+  @{
+ */
+
+#include "cmsis_version.h"
+ 
+/*  CMSIS CM0 definitions */
+#define __CM0_CMSIS_VERSION_MAIN  (__CM_CMSIS_VERSION_MAIN)              /*!< \deprecated [31:16] CMSIS HAL main version */
+#define __CM0_CMSIS_VERSION_SUB   (__CM_CMSIS_VERSION_SUB)               /*!< \deprecated [15:0]  CMSIS HAL sub version */
+#define __CM0_CMSIS_VERSION       ((__CM0_CMSIS_VERSION_MAIN << 16U) | \
+                                    __CM0_CMSIS_VERSION_SUB           )  /*!< \deprecated CMSIS HAL version number */
+
+#define __CORTEX_M                (0U)                                   /*!< Cortex-M Core */
+
+/** __FPU_USED indicates whether an FPU is used or not.
+    This core does not support an FPU at all
+*/
+#define __FPU_USED       0U
+
+#if defined ( __CC_ARM )
+  #if defined __TARGET_FPU_VFP
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined (__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050)
+  #if defined __ARM_PCS_VFP
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined ( __GNUC__ )
+  #if defined (__VFP_FP__) && !defined(__SOFTFP__)
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined ( __ICCARM__ )
+  #if defined __ARMVFP__
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined ( __TI_ARM__ )
+  #if defined __TI_VFP_SUPPORT__
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined ( __TASKING__ )
+  #if defined __FPU_VFP__
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined ( __CSMC__ )
+  #if ( __CSMC__ & 0x400U)
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#endif
+
+#include "cmsis_compiler.h"               /* CMSIS compiler specific defines */
+
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __CORE_CM0_H_GENERIC */
+
+#ifndef __CMSIS_GENERIC
+
+#ifndef __CORE_CM0_H_DEPENDANT
+#define __CORE_CM0_H_DEPENDANT
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* check device defines and use defaults */
+#if defined __CHECK_DEVICE_DEFINES
+  #ifndef __CM0_REV
+    #define __CM0_REV               0x0000U
+    #warning "__CM0_REV not defined in device header file; using default!"
+  #endif
+
+  #ifndef __NVIC_PRIO_BITS
+    #define __NVIC_PRIO_BITS          2U
+    #warning "__NVIC_PRIO_BITS not defined in device header file; using default!"
+  #endif
+
+  #ifndef __Vendor_SysTickConfig
+    #define __Vendor_SysTickConfig    0U
+    #warning "__Vendor_SysTickConfig not defined in device header file; using default!"
+  #endif
+#endif
+
+/* IO definitions (access restrictions to peripheral registers) */
+/**
+    \defgroup CMSIS_glob_defs CMSIS Global Defines
+
+    <strong>IO Type Qualifiers</strong> are used
+    \li to specify the access to peripheral variables.
+    \li for automatic generation of peripheral register debug information.
+*/
+#ifdef __cplusplus
+  #define   __I     volatile             /*!< Defines 'read only' permissions */
+#else
+  #define   __I     volatile const       /*!< Defines 'read only' permissions */
+#endif
+#define     __O     volatile             /*!< Defines 'write only' permissions */
+#define     __IO    volatile             /*!< Defines 'read / write' permissions */
+
+/* following defines should be used for structure members */
+#define     __IM     volatile const      /*! Defines 'read only' structure member permissions */
+#define     __OM     volatile            /*! Defines 'write only' structure member permissions */
+#define     __IOM    volatile            /*! Defines 'read / write' structure member permissions */
+
+/*@} end of group Cortex_M0 */
+
+
+
+/*******************************************************************************
+ *                 Register Abstraction
+  Core Register contain:
+  - Core Register
+  - Core NVIC Register
+  - Core SCB Register
+  - Core SysTick Register
+ ******************************************************************************/
+/**
+  \defgroup CMSIS_core_register Defines and Type Definitions
+  \brief Type definitions and defines for Cortex-M processor based devices.
+*/
+
+/**
+  \ingroup    CMSIS_core_register
+  \defgroup   CMSIS_CORE  Status and Control Registers
+  \brief      Core Register type definitions.
+  @{
+ */
+
+/**
+  \brief  Union type to access the Application Program Status Register (APSR).
+ */
+typedef union
+{
+  struct
+  {
+    uint32_t _reserved0:28;              /*!< bit:  0..27  Reserved */
+    uint32_t V:1;                        /*!< bit:     28  Overflow condition code flag */
+    uint32_t C:1;                        /*!< bit:     29  Carry condition code flag */
+    uint32_t Z:1;                        /*!< bit:     30  Zero condition code flag */
+    uint32_t N:1;                        /*!< bit:     31  Negative condition code flag */
+  } b;                                   /*!< Structure used for bit  access */
+  uint32_t w;                            /*!< Type      used for word access */
+} APSR_Type;
+
+/* APSR Register Definitions */
+#define APSR_N_Pos                         31U                                            /*!< APSR: N Position */
+#define APSR_N_Msk                         (1UL << APSR_N_Pos)                            /*!< APSR: N Mask */
+
+#define APSR_Z_Pos                         30U                                            /*!< APSR: Z Position */
+#define APSR_Z_Msk                         (1UL << APSR_Z_Pos)                            /*!< APSR: Z Mask */
+
+#define APSR_C_Pos                         29U                                            /*!< APSR: C Position */
+#define APSR_C_Msk                         (1UL << APSR_C_Pos)                            /*!< APSR: C Mask */
+
+#define APSR_V_Pos                         28U                                            /*!< APSR: V Position */
+#define APSR_V_Msk                         (1UL << APSR_V_Pos)                            /*!< APSR: V Mask */
+
+
+/**
+  \brief  Union type to access the Interrupt Program Status Register (IPSR).
+ */
+typedef union
+{
+  struct
+  {
+    uint32_t ISR:9;                      /*!< bit:  0.. 8  Exception number */
+    uint32_t _reserved0:23;              /*!< bit:  9..31  Reserved */
+  } b;                                   /*!< Structure used for bit  access */
+  uint32_t w;                            /*!< Type      used for word access */
+} IPSR_Type;
+
+/* IPSR Register Definitions */
+#define IPSR_ISR_Pos                        0U                                            /*!< IPSR: ISR Position */
+#define IPSR_ISR_Msk                       (0x1FFUL /*<< IPSR_ISR_Pos*/)                  /*!< IPSR: ISR Mask */
+
+
+/**
+  \brief  Union type to access the Special-Purpose Program Status Registers (xPSR).
+ */
+typedef union
+{
+  struct
+  {
+    uint32_t ISR:9;                      /*!< bit:  0.. 8  Exception number */
+    uint32_t _reserved0:15;              /*!< bit:  9..23  Reserved */
+    uint32_t T:1;                        /*!< bit:     24  Thumb bit        (read 0) */
+    uint32_t _reserved1:3;               /*!< bit: 25..27  Reserved */
+    uint32_t V:1;                        /*!< bit:     28  Overflow condition code flag */
+    uint32_t C:1;                        /*!< bit:     29  Carry condition code flag */
+    uint32_t Z:1;                        /*!< bit:     30  Zero condition code flag */
+    uint32_t N:1;                        /*!< bit:     31  Negative condition code flag */
+  } b;                                   /*!< Structure used for bit  access */
+  uint32_t w;                            /*!< Type      used for word access */
+} xPSR_Type;
+
+/* xPSR Register Definitions */
+#define xPSR_N_Pos                         31U                                            /*!< xPSR: N Position */
+#define xPSR_N_Msk                         (1UL << xPSR_N_Pos)                            /*!< xPSR: N Mask */
+
+#define xPSR_Z_Pos                         30U                                            /*!< xPSR: Z Position */
+#define xPSR_Z_Msk                         (1UL << xPSR_Z_Pos)                            /*!< xPSR: Z Mask */
+
+#define xPSR_C_Pos                         29U                                            /*!< xPSR: C Position */
+#define xPSR_C_Msk                         (1UL << xPSR_C_Pos)                            /*!< xPSR: C Mask */
+
+#define xPSR_V_Pos                         28U                                            /*!< xPSR: V Position */
+#define xPSR_V_Msk                         (1UL << xPSR_V_Pos)                            /*!< xPSR: V Mask */
+
+#define xPSR_T_Pos                         24U                                            /*!< xPSR: T Position */
+#define xPSR_T_Msk                         (1UL << xPSR_T_Pos)                            /*!< xPSR: T Mask */
+
+#define xPSR_ISR_Pos                        0U                                            /*!< xPSR: ISR Position */
+#define xPSR_ISR_Msk                       (0x1FFUL /*<< xPSR_ISR_Pos*/)                  /*!< xPSR: ISR Mask */
+
+
+/**
+  \brief  Union type to access the Control Registers (CONTROL).
+ */
+typedef union
+{
+  struct
+  {
+    uint32_t _reserved0:1;               /*!< bit:      0  Reserved */
+    uint32_t SPSEL:1;                    /*!< bit:      1  Stack to be used */
+    uint32_t _reserved1:30;              /*!< bit:  2..31  Reserved */
+  } b;                                   /*!< Structure used for bit  access */
+  uint32_t w;                            /*!< Type      used for word access */
+} CONTROL_Type;
+
+/* CONTROL Register Definitions */
+#define CONTROL_SPSEL_Pos                   1U                                            /*!< CONTROL: SPSEL Position */
+#define CONTROL_SPSEL_Msk                  (1UL << CONTROL_SPSEL_Pos)                     /*!< CONTROL: SPSEL Mask */
+
+/*@} end of group CMSIS_CORE */
+
+
+/**
+  \ingroup    CMSIS_core_register
+  \defgroup   CMSIS_NVIC  Nested Vectored Interrupt Controller (NVIC)
+  \brief      Type definitions for the NVIC Registers
+  @{
+ */
+
+/**
+  \brief  Structure type to access the Nested Vectored Interrupt Controller (NVIC).
+ */
+typedef struct
+{
+  __IOM uint32_t ISER[1U];               /*!< Offset: 0x000 (R/W)  Interrupt Set Enable Register */
+        uint32_t RESERVED0[31U];
+  __IOM uint32_t ICER[1U];               /*!< Offset: 0x080 (R/W)  Interrupt Clear Enable Register */
+        uint32_t RSERVED1[31U];
+  __IOM uint32_t ISPR[1U];               /*!< Offset: 0x100 (R/W)  Interrupt Set Pending Register */
+        uint32_t RESERVED2[31U];
+  __IOM uint32_t ICPR[1U];               /*!< Offset: 0x180 (R/W)  Interrupt Clear Pending Register */
+        uint32_t RESERVED3[31U];
+        uint32_t RESERVED4[64U];
+  __IOM uint32_t IP[8U];                 /*!< Offset: 0x300 (R/W)  Interrupt Priority Register */
+}  NVIC_Type;
+
+/*@} end of group CMSIS_NVIC */
+
+
+/**
+  \ingroup  CMSIS_core_register
+  \defgroup CMSIS_SCB     System Control Block (SCB)
+  \brief    Type definitions for the System Control Block Registers
+  @{
+ */
+
+/**
+  \brief  Structure type to access the System Control Block (SCB).
+ */
+typedef struct
+{
+  __IM  uint32_t CPUID;                  /*!< Offset: 0x000 (R/ )  CPUID Base Register */
+  __IOM uint32_t ICSR;                   /*!< Offset: 0x004 (R/W)  Interrupt Control and State Register */
+        uint32_t RESERVED0;
+  __IOM uint32_t AIRCR;                  /*!< Offset: 0x00C (R/W)  Application Interrupt and Reset Control Register */
+  __IOM uint32_t SCR;                    /*!< Offset: 0x010 (R/W)  System Control Register */
+  __IOM uint32_t CCR;                    /*!< Offset: 0x014 (R/W)  Configuration Control Register */
+        uint32_t RESERVED1;
+  __IOM uint32_t SHP[2U];                /*!< Offset: 0x01C (R/W)  System Handlers Priority Registers. [0] is RESERVED */
+  __IOM uint32_t SHCSR;                  /*!< Offset: 0x024 (R/W)  System Handler Control and State Register */
+} SCB_Type;
+
+/* SCB CPUID Register Definitions */
+#define SCB_CPUID_IMPLEMENTER_Pos          24U                                            /*!< SCB CPUID: IMPLEMENTER Position */
+#define SCB_CPUID_IMPLEMENTER_Msk          (0xFFUL << SCB_CPUID_IMPLEMENTER_Pos)          /*!< SCB CPUID: IMPLEMENTER Mask */
+
+#define SCB_CPUID_VARIANT_Pos              20U                                            /*!< SCB CPUID: VARIANT Position */
+#define SCB_CPUID_VARIANT_Msk              (0xFUL << SCB_CPUID_VARIANT_Pos)               /*!< SCB CPUID: VARIANT Mask */
+
+#define SCB_CPUID_ARCHITECTURE_Pos         16U                                            /*!< SCB CPUID: ARCHITECTURE Position */
+#define SCB_CPUID_ARCHITECTURE_Msk         (0xFUL << SCB_CPUID_ARCHITECTURE_Pos)          /*!< SCB CPUID: ARCHITECTURE Mask */
+
+#define SCB_CPUID_PARTNO_Pos                4U                                            /*!< SCB CPUID: PARTNO Position */
+#define SCB_CPUID_PARTNO_Msk               (0xFFFUL << SCB_CPUID_PARTNO_Pos)              /*!< SCB CPUID: PARTNO Mask */
+
+#define SCB_CPUID_REVISION_Pos              0U                                            /*!< SCB CPUID: REVISION Position */
+#define SCB_CPUID_REVISION_Msk             (0xFUL /*<< SCB_CPUID_REVISION_Pos*/)          /*!< SCB CPUID: REVISION Mask */
+
+/* SCB Interrupt Control State Register Definitions */
+#define SCB_ICSR_NMIPENDSET_Pos            31U                                            /*!< SCB ICSR: NMIPENDSET Position */
+#define SCB_ICSR_NMIPENDSET_Msk            (1UL << SCB_ICSR_NMIPENDSET_Pos)               /*!< SCB ICSR: NMIPENDSET Mask */
+
+#define SCB_ICSR_PENDSVSET_Pos             28U                                            /*!< SCB ICSR: PENDSVSET Position */
+#define SCB_ICSR_PENDSVSET_Msk             (1UL << SCB_ICSR_PENDSVSET_Pos)                /*!< SCB ICSR: PENDSVSET Mask */
+
+#define SCB_ICSR_PENDSVCLR_Pos             27U                                            /*!< SCB ICSR: PENDSVCLR Position */
+#define SCB_ICSR_PENDSVCLR_Msk             (1UL << SCB_ICSR_PENDSVCLR_Pos)                /*!< SCB ICSR: PENDSVCLR Mask */
+
+#define SCB_ICSR_PENDSTSET_Pos             26U                                            /*!< SCB ICSR: PENDSTSET Position */
+#define SCB_ICSR_PENDSTSET_Msk             (1UL << SCB_ICSR_PENDSTSET_Pos)                /*!< SCB ICSR: PENDSTSET Mask */
+
+#define SCB_ICSR_PENDSTCLR_Pos             25U                                            /*!< SCB ICSR: PENDSTCLR Position */
+#define SCB_ICSR_PENDSTCLR_Msk             (1UL << SCB_ICSR_PENDSTCLR_Pos)                /*!< SCB ICSR: PENDSTCLR Mask */
+
+#define SCB_ICSR_ISRPREEMPT_Pos            23U                                            /*!< SCB ICSR: ISRPREEMPT Position */
+#define SCB_ICSR_ISRPREEMPT_Msk            (1UL << SCB_ICSR_ISRPREEMPT_Pos)               /*!< SCB ICSR: ISRPREEMPT Mask */
+
+#define SCB_ICSR_ISRPENDING_Pos            22U                                            /*!< SCB ICSR: ISRPENDING Position */
+#define SCB_ICSR_ISRPENDING_Msk            (1UL << SCB_ICSR_ISRPENDING_Pos)               /*!< SCB ICSR: ISRPENDING Mask */
+
+#define SCB_ICSR_VECTPENDING_Pos           12U                                            /*!< SCB ICSR: VECTPENDING Position */
+#define SCB_ICSR_VECTPENDING_Msk           (0x1FFUL << SCB_ICSR_VECTPENDING_Pos)          /*!< SCB ICSR: VECTPENDING Mask */
+
+#define SCB_ICSR_VECTACTIVE_Pos             0U                                            /*!< SCB ICSR: VECTACTIVE Position */
+#define SCB_ICSR_VECTACTIVE_Msk            (0x1FFUL /*<< SCB_ICSR_VECTACTIVE_Pos*/)       /*!< SCB ICSR: VECTACTIVE Mask */
+
+/* SCB Application Interrupt and Reset Control Register Definitions */
+#define SCB_AIRCR_VECTKEY_Pos              16U                                            /*!< SCB AIRCR: VECTKEY Position */
+#define SCB_AIRCR_VECTKEY_Msk              (0xFFFFUL << SCB_AIRCR_VECTKEY_Pos)            /*!< SCB AIRCR: VECTKEY Mask */
+
+#define SCB_AIRCR_VECTKEYSTAT_Pos          16U                                            /*!< SCB AIRCR: VECTKEYSTAT Position */
+#define SCB_AIRCR_VECTKEYSTAT_Msk          (0xFFFFUL << SCB_AIRCR_VECTKEYSTAT_Pos)        /*!< SCB AIRCR: VECTKEYSTAT Mask */
+
+#define SCB_AIRCR_ENDIANESS_Pos            15U                                            /*!< SCB AIRCR: ENDIANESS Position */
+#define SCB_AIRCR_ENDIANESS_Msk            (1UL << SCB_AIRCR_ENDIANESS_Pos)               /*!< SCB AIRCR: ENDIANESS Mask */
+
+#define SCB_AIRCR_SYSRESETREQ_Pos           2U                                            /*!< SCB AIRCR: SYSRESETREQ Position */
+#define SCB_AIRCR_SYSRESETREQ_Msk          (1UL << SCB_AIRCR_SYSRESETREQ_Pos)             /*!< SCB AIRCR: SYSRESETREQ Mask */
+
+#define SCB_AIRCR_VECTCLRACTIVE_Pos         1U                                            /*!< SCB AIRCR: VECTCLRACTIVE Position */
+#define SCB_AIRCR_VECTCLRACTIVE_Msk        (1UL << SCB_AIRCR_VECTCLRACTIVE_Pos)           /*!< SCB AIRCR: VECTCLRACTIVE Mask */
+
+/* SCB System Control Register Definitions */
+#define SCB_SCR_SEVONPEND_Pos               4U                                            /*!< SCB SCR: SEVONPEND Position */
+#define SCB_SCR_SEVONPEND_Msk              (1UL << SCB_SCR_SEVONPEND_Pos)                 /*!< SCB SCR: SEVONPEND Mask */
+
+#define SCB_SCR_SLEEPDEEP_Pos               2U                                            /*!< SCB SCR: SLEEPDEEP Position */
+#define SCB_SCR_SLEEPDEEP_Msk              (1UL << SCB_SCR_SLEEPDEEP_Pos)                 /*!< SCB SCR: SLEEPDEEP Mask */
+
+#define SCB_SCR_SLEEPONEXIT_Pos             1U                                            /*!< SCB SCR: SLEEPONEXIT Position */
+#define SCB_SCR_SLEEPONEXIT_Msk            (1UL << SCB_SCR_SLEEPONEXIT_Pos)               /*!< SCB SCR: SLEEPONEXIT Mask */
+
+/* SCB Configuration Control Register Definitions */
+#define SCB_CCR_STKALIGN_Pos                9U                                            /*!< SCB CCR: STKALIGN Position */
+#define SCB_CCR_STKALIGN_Msk               (1UL << SCB_CCR_STKALIGN_Pos)                  /*!< SCB CCR: STKALIGN Mask */
+
+#define SCB_CCR_UNALIGN_TRP_Pos             3U                                            /*!< SCB CCR: UNALIGN_TRP Position */
+#define SCB_CCR_UNALIGN_TRP_Msk            (1UL << SCB_CCR_UNALIGN_TRP_Pos)               /*!< SCB CCR: UNALIGN_TRP Mask */
+
+/* SCB System Handler Control and State Register Definitions */
+#define SCB_SHCSR_SVCALLPENDED_Pos         15U                                            /*!< SCB SHCSR: SVCALLPENDED Position */
+#define SCB_SHCSR_SVCALLPENDED_Msk         (1UL << SCB_SHCSR_SVCALLPENDED_Pos)            /*!< SCB SHCSR: SVCALLPENDED Mask */
+
+/*@} end of group CMSIS_SCB */
+
+
+/**
+  \ingroup  CMSIS_core_register
+  \defgroup CMSIS_SysTick     System Tick Timer (SysTick)
+  \brief    Type definitions for the System Timer Registers.
+  @{
+ */
+
+/**
+  \brief  Structure type to access the System Timer (SysTick).
+ */
+typedef struct
+{
+  __IOM uint32_t CTRL;                   /*!< Offset: 0x000 (R/W)  SysTick Control and Status Register */
+  __IOM uint32_t LOAD;                   /*!< Offset: 0x004 (R/W)  SysTick Reload Value Register */
+  __IOM uint32_t VAL;                    /*!< Offset: 0x008 (R/W)  SysTick Current Value Register */
+  __IM  uint32_t CALIB;                  /*!< Offset: 0x00C (R/ )  SysTick Calibration Register */
+} SysTick_Type;
+
+/* SysTick Control / Status Register Definitions */
+#define SysTick_CTRL_COUNTFLAG_Pos         16U                                            /*!< SysTick CTRL: COUNTFLAG Position */
+#define SysTick_CTRL_COUNTFLAG_Msk         (1UL << SysTick_CTRL_COUNTFLAG_Pos)            /*!< SysTick CTRL: COUNTFLAG Mask */
+
+#define SysTick_CTRL_CLKSOURCE_Pos          2U                                            /*!< SysTick CTRL: CLKSOURCE Position */
+#define SysTick_CTRL_CLKSOURCE_Msk         (1UL << SysTick_CTRL_CLKSOURCE_Pos)            /*!< SysTick CTRL: CLKSOURCE Mask */
+
+#define SysTick_CTRL_TICKINT_Pos            1U                                            /*!< SysTick CTRL: TICKINT Position */
+#define SysTick_CTRL_TICKINT_Msk           (1UL << SysTick_CTRL_TICKINT_Pos)              /*!< SysTick CTRL: TICKINT Mask */
+
+#define SysTick_CTRL_ENABLE_Pos             0U                                            /*!< SysTick CTRL: ENABLE Position */
+#define SysTick_CTRL_ENABLE_Msk            (1UL /*<< SysTick_CTRL_ENABLE_Pos*/)           /*!< SysTick CTRL: ENABLE Mask */
+
+/* SysTick Reload Register Definitions */
+#define SysTick_LOAD_RELOAD_Pos             0U                                            /*!< SysTick LOAD: RELOAD Position */
+#define SysTick_LOAD_RELOAD_Msk            (0xFFFFFFUL /*<< SysTick_LOAD_RELOAD_Pos*/)    /*!< SysTick LOAD: RELOAD Mask */
+
+/* SysTick Current Register Definitions */
+#define SysTick_VAL_CURRENT_Pos             0U                                            /*!< SysTick VAL: CURRENT Position */
+#define SysTick_VAL_CURRENT_Msk            (0xFFFFFFUL /*<< SysTick_VAL_CURRENT_Pos*/)    /*!< SysTick VAL: CURRENT Mask */
+
+/* SysTick Calibration Register Definitions */
+#define SysTick_CALIB_NOREF_Pos            31U                                            /*!< SysTick CALIB: NOREF Position */
+#define SysTick_CALIB_NOREF_Msk            (1UL << SysTick_CALIB_NOREF_Pos)               /*!< SysTick CALIB: NOREF Mask */
+
+#define SysTick_CALIB_SKEW_Pos             30U                                            /*!< SysTick CALIB: SKEW Position */
+#define SysTick_CALIB_SKEW_Msk             (1UL << SysTick_CALIB_SKEW_Pos)                /*!< SysTick CALIB: SKEW Mask */
+
+#define SysTick_CALIB_TENMS_Pos             0U                                            /*!< SysTick CALIB: TENMS Position */
+#define SysTick_CALIB_TENMS_Msk            (0xFFFFFFUL /*<< SysTick_CALIB_TENMS_Pos*/)    /*!< SysTick CALIB: TENMS Mask */
+
+/*@} end of group CMSIS_SysTick */
+
+
+/**
+  \ingroup  CMSIS_core_register
+  \defgroup CMSIS_CoreDebug       Core Debug Registers (CoreDebug)
+  \brief    Cortex-M0 Core Debug Registers (DCB registers, SHCSR, and DFSR) are only accessible over DAP and not via processor.
+            Therefore they are not covered by the Cortex-M0 header file.
+  @{
+ */
+/*@} end of group CMSIS_CoreDebug */
+
+
+/**
+  \ingroup    CMSIS_core_register
+  \defgroup   CMSIS_core_bitfield     Core register bit field macros
+  \brief      Macros for use with bit field definitions (xxx_Pos, xxx_Msk).
+  @{
+ */
+
+/**
+  \brief   Mask and shift a bit field value for use in a register bit range.
+  \param[in] field  Name of the register bit field.
+  \param[in] value  Value of the bit field. This parameter is interpreted as an uint32_t type.
+  \return           Masked and shifted value.
+*/
+#define _VAL2FLD(field, value)    (((uint32_t)(value) << field ## _Pos) & field ## _Msk)
+
+/**
+  \brief     Mask and shift a register value to extract a bit filed value.
+  \param[in] field  Name of the register bit field.
+  \param[in] value  Value of register. This parameter is interpreted as an uint32_t type.
+  \return           Masked and shifted bit field value.
+*/
+#define _FLD2VAL(field, value)    (((uint32_t)(value) & field ## _Msk) >> field ## _Pos)
+
+/*@} end of group CMSIS_core_bitfield */
+
+
+/**
+  \ingroup    CMSIS_core_register
+  \defgroup   CMSIS_core_base     Core Definitions
+  \brief      Definitions for base addresses, unions, and structures.
+  @{
+ */
+
+/* Memory mapping of Core Hardware */
+#define SCS_BASE            (0xE000E000UL)                            /*!< System Control Space Base Address */
+#define SysTick_BASE        (SCS_BASE +  0x0010UL)                    /*!< SysTick Base Address */
+#define NVIC_BASE           (SCS_BASE +  0x0100UL)                    /*!< NVIC Base Address */
+#define SCB_BASE            (SCS_BASE +  0x0D00UL)                    /*!< System Control Block Base Address */
+
+#define SCB                 ((SCB_Type       *)     SCB_BASE      )   /*!< SCB configuration struct */
+#define SysTick             ((SysTick_Type   *)     SysTick_BASE  )   /*!< SysTick configuration struct */
+#define NVIC                ((NVIC_Type      *)     NVIC_BASE     )   /*!< NVIC configuration struct */
+
+
+/*@} */
+
+
+
+/*******************************************************************************
+ *                Hardware Abstraction Layer
+  Core Function Interface contains:
+  - Core NVIC Functions
+  - Core SysTick Functions
+  - Core Register Access Functions
+ ******************************************************************************/
+/**
+  \defgroup CMSIS_Core_FunctionInterface Functions and Instructions Reference
+*/
+
+
+
+/* ##########################   NVIC functions  #################################### */
+/**
+  \ingroup  CMSIS_Core_FunctionInterface
+  \defgroup CMSIS_Core_NVICFunctions NVIC Functions
+  \brief    Functions that manage interrupts and exceptions via the NVIC.
+  @{
+ */
+
+#ifdef CMSIS_NVIC_VIRTUAL
+  #ifndef CMSIS_NVIC_VIRTUAL_HEADER_FILE
+    #define CMSIS_NVIC_VIRTUAL_HEADER_FILE "cmsis_nvic_virtual.h"
+  #endif
+  #include CMSIS_NVIC_VIRTUAL_HEADER_FILE
+#else
+  #define NVIC_SetPriorityGrouping    __NVIC_SetPriorityGrouping
+  #define NVIC_GetPriorityGrouping    __NVIC_GetPriorityGrouping
+  #define NVIC_EnableIRQ              __NVIC_EnableIRQ
+  #define NVIC_GetEnableIRQ           __NVIC_GetEnableIRQ
+  #define NVIC_DisableIRQ             __NVIC_DisableIRQ
+  #define NVIC_GetPendingIRQ          __NVIC_GetPendingIRQ
+  #define NVIC_SetPendingIRQ          __NVIC_SetPendingIRQ
+  #define NVIC_ClearPendingIRQ        __NVIC_ClearPendingIRQ
+/*#define NVIC_GetActive              __NVIC_GetActive             not available for Cortex-M0 */
+  #define NVIC_SetPriority            __NVIC_SetPriority
+  #define NVIC_GetPriority            __NVIC_GetPriority
+  #define NVIC_SystemReset            __NVIC_SystemReset
+#endif /* CMSIS_NVIC_VIRTUAL */
+
+#ifdef CMSIS_VECTAB_VIRTUAL
+  #ifndef CMSIS_VECTAB_VIRTUAL_HEADER_FILE
+    #define CMSIS_VECTAB_VIRTUAL_HEADER_FILE "cmsis_vectab_virtual.h"
+  #endif
+  #include CMSIS_VECTAB_VIRTUAL_HEADER_FILE
+#else
+  #define NVIC_SetVector              __NVIC_SetVector
+  #define NVIC_GetVector              __NVIC_GetVector
+#endif  /* (CMSIS_VECTAB_VIRTUAL) */
+
+#define NVIC_USER_IRQ_OFFSET          16
+
+
+/* The following EXC_RETURN values are saved the LR on exception entry */
+#define EXC_RETURN_HANDLER         (0xFFFFFFF1UL)     /* return to Handler mode, uses MSP after return                               */
+#define EXC_RETURN_THREAD_MSP      (0xFFFFFFF9UL)     /* return to Thread mode, uses MSP after return                                */
+#define EXC_RETURN_THREAD_PSP      (0xFFFFFFFDUL)     /* return to Thread mode, uses PSP after return                                */
+
+
+/* Interrupt Priorities are WORD accessible only under Armv6-M                  */
+/* The following MACROS handle generation of the register offset and byte masks */
+#define _BIT_SHIFT(IRQn)         (  ((((uint32_t)(int32_t)(IRQn))         )      &  0x03UL) * 8UL)
+#define _SHP_IDX(IRQn)           ( (((((uint32_t)(int32_t)(IRQn)) & 0x0FUL)-8UL) >>    2UL)      )
+#define _IP_IDX(IRQn)            (   (((uint32_t)(int32_t)(IRQn))                >>    2UL)      )
+
+#define __NVIC_SetPriorityGrouping(X) (void)(X)
+#define __NVIC_GetPriorityGrouping()  (0U)
+
+/**
+  \brief   Enable Interrupt
+  \details Enables a device specific interrupt in the NVIC interrupt controller.
+  \param [in]      IRQn  Device specific interrupt number.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE void __NVIC_EnableIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    NVIC->ISER[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL));
+  }
+}
+
+
+/**
+  \brief   Get Interrupt Enable status
+  \details Returns a device specific interrupt enable status from the NVIC interrupt controller.
+  \param [in]      IRQn  Device specific interrupt number.
+  \return             0  Interrupt is not enabled.
+  \return             1  Interrupt is enabled.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE uint32_t __NVIC_GetEnableIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    return((uint32_t)(((NVIC->ISER[0U] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL));
+  }
+  else
+  {
+    return(0U);
+  }
+}
+
+
+/**
+  \brief   Disable Interrupt
+  \details Disables a device specific interrupt in the NVIC interrupt controller.
+  \param [in]      IRQn  Device specific interrupt number.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE void __NVIC_DisableIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    NVIC->ICER[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL));
+    __DSB();
+    __ISB();
+  }
+}
+
+
+/**
+  \brief   Get Pending Interrupt
+  \details Reads the NVIC pending register and returns the pending bit for the specified device specific interrupt.
+  \param [in]      IRQn  Device specific interrupt number.
+  \return             0  Interrupt status is not pending.
+  \return             1  Interrupt status is pending.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE uint32_t __NVIC_GetPendingIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    return((uint32_t)(((NVIC->ISPR[0U] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL));
+  }
+  else
+  {
+    return(0U);
+  }
+}
+
+
+/**
+  \brief   Set Pending Interrupt
+  \details Sets the pending bit of a device specific interrupt in the NVIC pending register.
+  \param [in]      IRQn  Device specific interrupt number.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE void __NVIC_SetPendingIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    NVIC->ISPR[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL));
+  }
+}
+
+
+/**
+  \brief   Clear Pending Interrupt
+  \details Clears the pending bit of a device specific interrupt in the NVIC pending register.
+  \param [in]      IRQn  Device specific interrupt number.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE void __NVIC_ClearPendingIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    NVIC->ICPR[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL));
+  }
+}
+
+
+/**
+  \brief   Set Interrupt Priority
+  \details Sets the priority of a device specific interrupt or a processor exception.
+           The interrupt number can be positive to specify a device specific interrupt,
+           or negative to specify a processor exception.
+  \param [in]      IRQn  Interrupt number.
+  \param [in]  priority  Priority to set.
+  \note    The priority cannot be set for every processor exception.
+ */
+__STATIC_INLINE void __NVIC_SetPriority(IRQn_Type IRQn, uint32_t priority)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    NVIC->IP[_IP_IDX(IRQn)]  = ((uint32_t)(NVIC->IP[_IP_IDX(IRQn)]  & ~(0xFFUL << _BIT_SHIFT(IRQn))) |
+       (((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL) << _BIT_SHIFT(IRQn)));
+  }
+  else
+  {
+    SCB->SHP[_SHP_IDX(IRQn)] = ((uint32_t)(SCB->SHP[_SHP_IDX(IRQn)] & ~(0xFFUL << _BIT_SHIFT(IRQn))) |
+       (((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL) << _BIT_SHIFT(IRQn)));
+  }
+}
+
+
+/**
+  \brief   Get Interrupt Priority
+  \details Reads the priority of a device specific interrupt or a processor exception.
+           The interrupt number can be positive to specify a device specific interrupt,
+           or negative to specify a processor exception.
+  \param [in]   IRQn  Interrupt number.
+  \return             Interrupt Priority.
+                      Value is aligned automatically to the implemented priority bits of the microcontroller.
+ */
+__STATIC_INLINE uint32_t __NVIC_GetPriority(IRQn_Type IRQn)
+{
+
+  if ((int32_t)(IRQn) >= 0)
+  {
+    return((uint32_t)(((NVIC->IP[ _IP_IDX(IRQn)] >> _BIT_SHIFT(IRQn) ) & (uint32_t)0xFFUL) >> (8U - __NVIC_PRIO_BITS)));
+  }
+  else
+  {
+    return((uint32_t)(((SCB->SHP[_SHP_IDX(IRQn)] >> _BIT_SHIFT(IRQn) ) & (uint32_t)0xFFUL) >> (8U - __NVIC_PRIO_BITS)));
+  }
+}
+
+
+/**
+  \brief   Encode Priority
+  \details Encodes the priority for an interrupt with the given priority group,
+           preemptive priority value, and subpriority value.
+           In case of a conflict between priority grouping and available
+           priority bits (__NVIC_PRIO_BITS), the smallest possible priority group is set.
+  \param [in]     PriorityGroup  Used priority group.
+  \param [in]   PreemptPriority  Preemptive priority value (starting from 0).
+  \param [in]       SubPriority  Subpriority value (starting from 0).
+  \return                        Encoded priority. Value can be used in the function \ref NVIC_SetPriority().
+ */
+__STATIC_INLINE uint32_t NVIC_EncodePriority (uint32_t PriorityGroup, uint32_t PreemptPriority, uint32_t SubPriority)
+{
+  uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL);   /* only values 0..7 are used          */
+  uint32_t PreemptPriorityBits;
+  uint32_t SubPriorityBits;
+
+  PreemptPriorityBits = ((7UL - PriorityGroupTmp) > (uint32_t)(__NVIC_PRIO_BITS)) ? (uint32_t)(__NVIC_PRIO_BITS) : (uint32_t)(7UL - PriorityGroupTmp);
+  SubPriorityBits     = ((PriorityGroupTmp + (uint32_t)(__NVIC_PRIO_BITS)) < (uint32_t)7UL) ? (uint32_t)0UL : (uint32_t)((PriorityGroupTmp - 7UL) + (uint32_t)(__NVIC_PRIO_BITS));
+
+  return (
+           ((PreemptPriority & (uint32_t)((1UL << (PreemptPriorityBits)) - 1UL)) << SubPriorityBits) |
+           ((SubPriority     & (uint32_t)((1UL << (SubPriorityBits    )) - 1UL)))
+         );
+}
+
+
+/**
+  \brief   Decode Priority
+  \details Decodes an interrupt priority value with a given priority group to
+           preemptive priority value and subpriority value.
+           In case of a conflict between priority grouping and available
+           priority bits (__NVIC_PRIO_BITS) the smallest possible priority group is set.
+  \param [in]         Priority   Priority value, which can be retrieved with the function \ref NVIC_GetPriority().
+  \param [in]     PriorityGroup  Used priority group.
+  \param [out] pPreemptPriority  Preemptive priority value (starting from 0).
+  \param [out]     pSubPriority  Subpriority value (starting from 0).
+ */
+__STATIC_INLINE void NVIC_DecodePriority (uint32_t Priority, uint32_t PriorityGroup, uint32_t* const pPreemptPriority, uint32_t* const pSubPriority)
+{
+  uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL);   /* only values 0..7 are used          */
+  uint32_t PreemptPriorityBits;
+  uint32_t SubPriorityBits;
+
+  PreemptPriorityBits = ((7UL - PriorityGroupTmp) > (uint32_t)(__NVIC_PRIO_BITS)) ? (uint32_t)(__NVIC_PRIO_BITS) : (uint32_t)(7UL - PriorityGroupTmp);
+  SubPriorityBits     = ((PriorityGroupTmp + (uint32_t)(__NVIC_PRIO_BITS)) < (uint32_t)7UL) ? (uint32_t)0UL : (uint32_t)((PriorityGroupTmp - 7UL) + (uint32_t)(__NVIC_PRIO_BITS));
+
+  *pPreemptPriority = (Priority >> SubPriorityBits) & (uint32_t)((1UL << (PreemptPriorityBits)) - 1UL);
+  *pSubPriority     = (Priority                   ) & (uint32_t)((1UL << (SubPriorityBits    )) - 1UL);
+}
+
+
+
+/**
+  \brief   Set Interrupt Vector
+  \details Sets an interrupt vector in SRAM based interrupt vector table.
+           The interrupt number can be positive to specify a device specific interrupt,
+           or negative to specify a processor exception.
+           Address 0 must be mapped to SRAM.
+  \param [in]   IRQn      Interrupt number
+  \param [in]   vector    Address of interrupt handler function
+ */
+__STATIC_INLINE void __NVIC_SetVector(IRQn_Type IRQn, uint32_t vector)
+{
+  uint32_t *vectors = (uint32_t *)0x0U;
+  vectors[(int32_t)IRQn + NVIC_USER_IRQ_OFFSET] = vector;
+}
+
+
+/**
+  \brief   Get Interrupt Vector
+  \details Reads an interrupt vector from interrupt vector table.
+           The interrupt number can be positive to specify a device specific interrupt,
+           or negative to specify a processor exception.
+  \param [in]   IRQn      Interrupt number.
+  \return                 Address of interrupt handler function
+ */
+__STATIC_INLINE uint32_t __NVIC_GetVector(IRQn_Type IRQn)
+{
+  uint32_t *vectors = (uint32_t *)0x0U;
+  return vectors[(int32_t)IRQn + NVIC_USER_IRQ_OFFSET];
+}
+
+
+/**
+  \brief   System Reset
+  \details Initiates a system reset request to reset the MCU.
+ */
+__NO_RETURN __STATIC_INLINE void __NVIC_SystemReset(void)
+{
+  __DSB();                                                          /* Ensure all outstanding memory accesses included
+                                                                       buffered write are completed before reset */
+  SCB->AIRCR  = ((0x5FAUL << SCB_AIRCR_VECTKEY_Pos) |
+                 SCB_AIRCR_SYSRESETREQ_Msk);
+  __DSB();                                                          /* Ensure completion of memory access */
+
+  for(;;)                                                           /* wait until reset */
+  {
+    __NOP();
+  }
+}
+
+/*@} end of CMSIS_Core_NVICFunctions */
+
+
+/* ##########################  FPU functions  #################################### */
+/**
+  \ingroup  CMSIS_Core_FunctionInterface
+  \defgroup CMSIS_Core_FpuFunctions FPU Functions
+  \brief    Function that provides FPU type.
+  @{
+ */
+
+/**
+  \brief   get FPU type
+  \details returns the FPU type
+  \returns
+   - \b  0: No FPU
+   - \b  1: Single precision FPU
+   - \b  2: Double + Single precision FPU
+ */
+__STATIC_INLINE uint32_t SCB_GetFPUType(void)
+{
+    return 0U;           /* No FPU */
+}
+
+
+/*@} end of CMSIS_Core_FpuFunctions */
+
+
+
+/* ##################################    SysTick function  ############################################ */
+/**
+  \ingroup  CMSIS_Core_FunctionInterface
+  \defgroup CMSIS_Core_SysTickFunctions SysTick Functions
+  \brief    Functions that configure the System.
+  @{
+ */
+
+#if defined (__Vendor_SysTickConfig) && (__Vendor_SysTickConfig == 0U)
+
+/**
+  \brief   System Tick Configuration
+  \details Initializes the System Timer and its interrupt, and starts the System Tick Timer.
+           Counter is in free running mode to generate periodic interrupts.
+  \param [in]  ticks  Number of ticks between two interrupts.
+  \return          0  Function succeeded.
+  \return          1  Function failed.
+  \note    When the variable <b>__Vendor_SysTickConfig</b> is set to 1, then the
+           function <b>SysTick_Config</b> is not included. In this case, the file <b><i>device</i>.h</b>
+           must contain a vendor-specific implementation of this function.
+ */
+__STATIC_INLINE uint32_t SysTick_Config(uint32_t ticks)
+{
+  if ((ticks - 1UL) > SysTick_LOAD_RELOAD_Msk)
+  {
+    return (1UL);                                                   /* Reload value impossible */
+  }
+
+  SysTick->LOAD  = (uint32_t)(ticks - 1UL);                         /* set reload register */
+  NVIC_SetPriority (SysTick_IRQn, (1UL << __NVIC_PRIO_BITS) - 1UL); /* set Priority for Systick Interrupt */
+  SysTick->VAL   = 0UL;                                             /* Load the SysTick Counter Value */
+  SysTick->CTRL  = SysTick_CTRL_CLKSOURCE_Msk |
+                   SysTick_CTRL_TICKINT_Msk   |
+                   SysTick_CTRL_ENABLE_Msk;                         /* Enable SysTick IRQ and SysTick Timer */
+  return (0UL);                                                     /* Function successful */
+}
+
+#endif
+
+/*@} end of CMSIS_Core_SysTickFunctions */
+
+
+
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __CORE_CM0_H_DEPENDANT */
+
+#endif /* __CMSIS_GENERIC */

Drivers/CMSIS/Include/core_cm1.h

@@ -0,0 +1,976 @@
+/**************************************************************************//**
+ * @file     core_cm1.h
+ * @brief    CMSIS Cortex-M1 Core Peripheral Access Layer Header File
+ * @version  V1.0.0
+ * @date     23. July 2018
+ ******************************************************************************/
+/*
+ * Copyright (c) 2009-2018 Arm Limited. All rights reserved.
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the License); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an AS IS BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#if   defined ( __ICCARM__ )
+  #pragma system_include         /* treat file as system include file for MISRA check */
+#elif defined (__clang__)
+  #pragma clang system_header   /* treat file as system include file */
+#endif
+
+#ifndef __CORE_CM1_H_GENERIC
+#define __CORE_CM1_H_GENERIC
+
+#include <stdint.h>
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/**
+  \page CMSIS_MISRA_Exceptions  MISRA-C:2004 Compliance Exceptions
+  CMSIS violates the following MISRA-C:2004 rules:
+
+   \li Required Rule 8.5, object/function definition in header file.<br>
+     Function definitions in header files are used to allow 'inlining'.
+
+   \li Required Rule 18.4, declaration of union type or object of union type: '{...}'.<br>
+     Unions are used for effective representation of core registers.
+
+   \li Advisory Rule 19.7, Function-like macro defined.<br>
+     Function-like macros are used to allow more efficient code.
+ */
+
+
+/*******************************************************************************
+ *                 CMSIS definitions
+ ******************************************************************************/
+/**
+  \ingroup Cortex_M1
+  @{
+ */
+
+#include "cmsis_version.h"
+ 
+/*  CMSIS CM1 definitions */
+#define __CM1_CMSIS_VERSION_MAIN  (__CM_CMSIS_VERSION_MAIN)              /*!< \deprecated [31:16] CMSIS HAL main version */
+#define __CM1_CMSIS_VERSION_SUB   (__CM_CMSIS_VERSION_SUB)               /*!< \deprecated [15:0]  CMSIS HAL sub version */
+#define __CM1_CMSIS_VERSION       ((__CM1_CMSIS_VERSION_MAIN << 16U) | \
+                                    __CM1_CMSIS_VERSION_SUB           )  /*!< \deprecated CMSIS HAL version number */
+
+#define __CORTEX_M                (1U)                                   /*!< Cortex-M Core */
+
+/** __FPU_USED indicates whether an FPU is used or not.
+    This core does not support an FPU at all
+*/
+#define __FPU_USED       0U
+
+#if defined ( __CC_ARM )
+  #if defined __TARGET_FPU_VFP
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined (__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050)
+  #if defined __ARM_PCS_VFP
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined ( __GNUC__ )
+  #if defined (__VFP_FP__) && !defined(__SOFTFP__)
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined ( __ICCARM__ )
+  #if defined __ARMVFP__
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined ( __TI_ARM__ )
+  #if defined __TI_VFP_SUPPORT__
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined ( __TASKING__ )
+  #if defined __FPU_VFP__
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#elif defined ( __CSMC__ )
+  #if ( __CSMC__ & 0x400U)
+    #error "Compiler generates FPU instructions for a device without an FPU (check __FPU_PRESENT)"
+  #endif
+
+#endif
+
+#include "cmsis_compiler.h"               /* CMSIS compiler specific defines */
+
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __CORE_CM1_H_GENERIC */
+
+#ifndef __CMSIS_GENERIC
+
+#ifndef __CORE_CM1_H_DEPENDANT
+#define __CORE_CM1_H_DEPENDANT
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* check device defines and use defaults */
+#if defined __CHECK_DEVICE_DEFINES
+  #ifndef __CM1_REV
+    #define __CM1_REV               0x0100U
+    #warning "__CM1_REV not defined in device header file; using default!"
+  #endif
+
+  #ifndef __NVIC_PRIO_BITS
+    #define __NVIC_PRIO_BITS          2U
+    #warning "__NVIC_PRIO_BITS not defined in device header file; using default!"
+  #endif
+
+  #ifndef __Vendor_SysTickConfig
+    #define __Vendor_SysTickConfig    0U
+    #warning "__Vendor_SysTickConfig not defined in device header file; using default!"
+  #endif
+#endif
+
+/* IO definitions (access restrictions to peripheral registers) */
+/**
+    \defgroup CMSIS_glob_defs CMSIS Global Defines
+
+    <strong>IO Type Qualifiers</strong> are used
+    \li to specify the access to peripheral variables.
+    \li for automatic generation of peripheral register debug information.
+*/
+#ifdef __cplusplus
+  #define   __I     volatile             /*!< Defines 'read only' permissions */
+#else
+  #define   __I     volatile const       /*!< Defines 'read only' permissions */
+#endif
+#define     __O     volatile             /*!< Defines 'write only' permissions */
+#define     __IO    volatile             /*!< Defines 'read / write' permissions */
+
+/* following defines should be used for structure members */
+#define     __IM     volatile const      /*! Defines 'read only' structure member permissions */
+#define     __OM     volatile            /*! Defines 'write only' structure member permissions */
+#define     __IOM    volatile            /*! Defines 'read / write' structure member permissions */
+
+/*@} end of group Cortex_M1 */
+
+
+
+/*******************************************************************************
+ *                 Register Abstraction
+  Core Register contain:
+  - Core Register
+  - Core NVIC Register
+  - Core SCB Register
+  - Core SysTick Register
+ ******************************************************************************/
+/**
+  \defgroup CMSIS_core_register Defines and Type Definitions
+  \brief Type definitions and defines for Cortex-M processor based devices.
+*/
+
+/**
+  \ingroup    CMSIS_core_register
+  \defgroup   CMSIS_CORE  Status and Control Registers
+  \brief      Core Register type definitions.
+  @{
+ */
+
+/**
+  \brief  Union type to access the Application Program Status Register (APSR).
+ */
+typedef union
+{
+  struct
+  {
+    uint32_t _reserved0:28;              /*!< bit:  0..27  Reserved */
+    uint32_t V:1;                        /*!< bit:     28  Overflow condition code flag */
+    uint32_t C:1;                        /*!< bit:     29  Carry condition code flag */
+    uint32_t Z:1;                        /*!< bit:     30  Zero condition code flag */
+    uint32_t N:1;                        /*!< bit:     31  Negative condition code flag */
+  } b;                                   /*!< Structure used for bit  access */
+  uint32_t w;                            /*!< Type      used for word access */
+} APSR_Type;
+
+/* APSR Register Definitions */
+#define APSR_N_Pos                         31U                                            /*!< APSR: N Position */
+#define APSR_N_Msk                         (1UL << APSR_N_Pos)                            /*!< APSR: N Mask */
+
+#define APSR_Z_Pos                         30U                                            /*!< APSR: Z Position */
+#define APSR_Z_Msk                         (1UL << APSR_Z_Pos)                            /*!< APSR: Z Mask */
+
+#define APSR_C_Pos                         29U                                            /*!< APSR: C Position */
+#define APSR_C_Msk                         (1UL << APSR_C_Pos)                            /*!< APSR: C Mask */
+
+#define APSR_V_Pos                         28U                                            /*!< APSR: V Position */
+#define APSR_V_Msk                         (1UL << APSR_V_Pos)                            /*!< APSR: V Mask */
+
+
+/**
+  \brief  Union type to access the Interrupt Program Status Register (IPSR).
+ */
+typedef union
+{
+  struct
+  {
+    uint32_t ISR:9;                      /*!< bit:  0.. 8  Exception number */
+    uint32_t _reserved0:23;              /*!< bit:  9..31  Reserved */
+  } b;                                   /*!< Structure used for bit  access */
+  uint32_t w;                            /*!< Type      used for word access */
+} IPSR_Type;
+
+/* IPSR Register Definitions */
+#define IPSR_ISR_Pos                        0U                                            /*!< IPSR: ISR Position */
+#define IPSR_ISR_Msk                       (0x1FFUL /*<< IPSR_ISR_Pos*/)                  /*!< IPSR: ISR Mask */
+
+
+/**
+  \brief  Union type to access the Special-Purpose Program Status Registers (xPSR).
+ */
+typedef union
+{
+  struct
+  {
+    uint32_t ISR:9;                      /*!< bit:  0.. 8  Exception number */
+    uint32_t _reserved0:15;              /*!< bit:  9..23  Reserved */
+    uint32_t T:1;                        /*!< bit:     24  Thumb bit        (read 0) */
+    uint32_t _reserved1:3;               /*!< bit: 25..27  Reserved */
+    uint32_t V:1;                        /*!< bit:     28  Overflow condition code flag */
+    uint32_t C:1;                        /*!< bit:     29  Carry condition code flag */
+    uint32_t Z:1;                        /*!< bit:     30  Zero condition code flag */
+    uint32_t N:1;                        /*!< bit:     31  Negative condition code flag */
+  } b;                                   /*!< Structure used for bit  access */
+  uint32_t w;                            /*!< Type      used for word access */
+} xPSR_Type;
+
+/* xPSR Register Definitions */
+#define xPSR_N_Pos                         31U                                            /*!< xPSR: N Position */
+#define xPSR_N_Msk                         (1UL << xPSR_N_Pos)                            /*!< xPSR: N Mask */
+
+#define xPSR_Z_Pos                         30U                                            /*!< xPSR: Z Position */
+#define xPSR_Z_Msk                         (1UL << xPSR_Z_Pos)                            /*!< xPSR: Z Mask */
+
+#define xPSR_C_Pos                         29U                                            /*!< xPSR: C Position */
+#define xPSR_C_Msk                         (1UL << xPSR_C_Pos)                            /*!< xPSR: C Mask */
+
+#define xPSR_V_Pos                         28U                                            /*!< xPSR: V Position */
+#define xPSR_V_Msk                         (1UL << xPSR_V_Pos)                            /*!< xPSR: V Mask */
+
+#define xPSR_T_Pos                         24U                                            /*!< xPSR: T Position */
+#define xPSR_T_Msk                         (1UL << xPSR_T_Pos)                            /*!< xPSR: T Mask */
+
+#define xPSR_ISR_Pos                        0U                                            /*!< xPSR: ISR Position */
+#define xPSR_ISR_Msk                       (0x1FFUL /*<< xPSR_ISR_Pos*/)                  /*!< xPSR: ISR Mask */
+
+
+/**
+  \brief  Union type to access the Control Registers (CONTROL).
+ */
+typedef union
+{
+  struct
+  {
+    uint32_t _reserved0:1;               /*!< bit:      0  Reserved */
+    uint32_t SPSEL:1;                    /*!< bit:      1  Stack to be used */
+    uint32_t _reserved1:30;              /*!< bit:  2..31  Reserved */
+  } b;                                   /*!< Structure used for bit  access */
+  uint32_t w;                            /*!< Type      used for word access */
+} CONTROL_Type;
+
+/* CONTROL Register Definitions */
+#define CONTROL_SPSEL_Pos                   1U                                            /*!< CONTROL: SPSEL Position */
+#define CONTROL_SPSEL_Msk                  (1UL << CONTROL_SPSEL_Pos)                     /*!< CONTROL: SPSEL Mask */
+
+/*@} end of group CMSIS_CORE */
+
+
+/**
+  \ingroup    CMSIS_core_register
+  \defgroup   CMSIS_NVIC  Nested Vectored Interrupt Controller (NVIC)
+  \brief      Type definitions for the NVIC Registers
+  @{
+ */
+
+/**
+  \brief  Structure type to access the Nested Vectored Interrupt Controller (NVIC).
+ */
+typedef struct
+{
+  __IOM uint32_t ISER[1U];               /*!< Offset: 0x000 (R/W)  Interrupt Set Enable Register */
+        uint32_t RESERVED0[31U];
+  __IOM uint32_t ICER[1U];               /*!< Offset: 0x080 (R/W)  Interrupt Clear Enable Register */
+        uint32_t RSERVED1[31U];
+  __IOM uint32_t ISPR[1U];               /*!< Offset: 0x100 (R/W)  Interrupt Set Pending Register */
+        uint32_t RESERVED2[31U];
+  __IOM uint32_t ICPR[1U];               /*!< Offset: 0x180 (R/W)  Interrupt Clear Pending Register */
+        uint32_t RESERVED3[31U];
+        uint32_t RESERVED4[64U];
+  __IOM uint32_t IP[8U];                 /*!< Offset: 0x300 (R/W)  Interrupt Priority Register */
+}  NVIC_Type;
+
+/*@} end of group CMSIS_NVIC */
+
+
+/**
+  \ingroup  CMSIS_core_register
+  \defgroup CMSIS_SCB     System Control Block (SCB)
+  \brief    Type definitions for the System Control Block Registers
+  @{
+ */
+
+/**
+  \brief  Structure type to access the System Control Block (SCB).
+ */
+typedef struct
+{
+  __IM  uint32_t CPUID;                  /*!< Offset: 0x000 (R/ )  CPUID Base Register */
+  __IOM uint32_t ICSR;                   /*!< Offset: 0x004 (R/W)  Interrupt Control and State Register */
+        uint32_t RESERVED0;
+  __IOM uint32_t AIRCR;                  /*!< Offset: 0x00C (R/W)  Application Interrupt and Reset Control Register */
+  __IOM uint32_t SCR;                    /*!< Offset: 0x010 (R/W)  System Control Register */
+  __IOM uint32_t CCR;                    /*!< Offset: 0x014 (R/W)  Configuration Control Register */
+        uint32_t RESERVED1;
+  __IOM uint32_t SHP[2U];                /*!< Offset: 0x01C (R/W)  System Handlers Priority Registers. [0] is RESERVED */
+  __IOM uint32_t SHCSR;                  /*!< Offset: 0x024 (R/W)  System Handler Control and State Register */
+} SCB_Type;
+
+/* SCB CPUID Register Definitions */
+#define SCB_CPUID_IMPLEMENTER_Pos          24U                                            /*!< SCB CPUID: IMPLEMENTER Position */
+#define SCB_CPUID_IMPLEMENTER_Msk          (0xFFUL << SCB_CPUID_IMPLEMENTER_Pos)          /*!< SCB CPUID: IMPLEMENTER Mask */
+
+#define SCB_CPUID_VARIANT_Pos              20U                                            /*!< SCB CPUID: VARIANT Position */
+#define SCB_CPUID_VARIANT_Msk              (0xFUL << SCB_CPUID_VARIANT_Pos)               /*!< SCB CPUID: VARIANT Mask */
+
+#define SCB_CPUID_ARCHITECTURE_Pos         16U                                            /*!< SCB CPUID: ARCHITECTURE Position */
+#define SCB_CPUID_ARCHITECTURE_Msk         (0xFUL << SCB_CPUID_ARCHITECTURE_Pos)          /*!< SCB CPUID: ARCHITECTURE Mask */
+
+#define SCB_CPUID_PARTNO_Pos                4U                                            /*!< SCB CPUID: PARTNO Position */
+#define SCB_CPUID_PARTNO_Msk               (0xFFFUL << SCB_CPUID_PARTNO_Pos)              /*!< SCB CPUID: PARTNO Mask */
+
+#define SCB_CPUID_REVISION_Pos              0U                                            /*!< SCB CPUID: REVISION Position */
+#define SCB_CPUID_REVISION_Msk             (0xFUL /*<< SCB_CPUID_REVISION_Pos*/)          /*!< SCB CPUID: REVISION Mask */
+
+/* SCB Interrupt Control State Register Definitions */
+#define SCB_ICSR_NMIPENDSET_Pos            31U                                            /*!< SCB ICSR: NMIPENDSET Position */
+#define SCB_ICSR_NMIPENDSET_Msk            (1UL << SCB_ICSR_NMIPENDSET_Pos)               /*!< SCB ICSR: NMIPENDSET Mask */
+
+#define SCB_ICSR_PENDSVSET_Pos             28U                                            /*!< SCB ICSR: PENDSVSET Position */
+#define SCB_ICSR_PENDSVSET_Msk             (1UL << SCB_ICSR_PENDSVSET_Pos)                /*!< SCB ICSR: PENDSVSET Mask */
+
+#define SCB_ICSR_PENDSVCLR_Pos             27U                                            /*!< SCB ICSR: PENDSVCLR Position */
+#define SCB_ICSR_PENDSVCLR_Msk             (1UL << SCB_ICSR_PENDSVCLR_Pos)                /*!< SCB ICSR: PENDSVCLR Mask */
+
+#define SCB_ICSR_PENDSTSET_Pos             26U                                            /*!< SCB ICSR: PENDSTSET Position */
+#define SCB_ICSR_PENDSTSET_Msk             (1UL << SCB_ICSR_PENDSTSET_Pos)                /*!< SCB ICSR: PENDSTSET Mask */
+
+#define SCB_ICSR_PENDSTCLR_Pos             25U                                            /*!< SCB ICSR: PENDSTCLR Position */
+#define SCB_ICSR_PENDSTCLR_Msk             (1UL << SCB_ICSR_PENDSTCLR_Pos)                /*!< SCB ICSR: PENDSTCLR Mask */
+
+#define SCB_ICSR_ISRPREEMPT_Pos            23U                                            /*!< SCB ICSR: ISRPREEMPT Position */
+#define SCB_ICSR_ISRPREEMPT_Msk            (1UL << SCB_ICSR_ISRPREEMPT_Pos)               /*!< SCB ICSR: ISRPREEMPT Mask */
+
+#define SCB_ICSR_ISRPENDING_Pos            22U                                            /*!< SCB ICSR: ISRPENDING Position */
+#define SCB_ICSR_ISRPENDING_Msk            (1UL << SCB_ICSR_ISRPENDING_Pos)               /*!< SCB ICSR: ISRPENDING Mask */
+
+#define SCB_ICSR_VECTPENDING_Pos           12U                                            /*!< SCB ICSR: VECTPENDING Position */
+#define SCB_ICSR_VECTPENDING_Msk           (0x1FFUL << SCB_ICSR_VECTPENDING_Pos)          /*!< SCB ICSR: VECTPENDING Mask */
+
+#define SCB_ICSR_VECTACTIVE_Pos             0U                                            /*!< SCB ICSR: VECTACTIVE Position */
+#define SCB_ICSR_VECTACTIVE_Msk            (0x1FFUL /*<< SCB_ICSR_VECTACTIVE_Pos*/)       /*!< SCB ICSR: VECTACTIVE Mask */
+
+/* SCB Application Interrupt and Reset Control Register Definitions */
+#define SCB_AIRCR_VECTKEY_Pos              16U                                            /*!< SCB AIRCR: VECTKEY Position */
+#define SCB_AIRCR_VECTKEY_Msk              (0xFFFFUL << SCB_AIRCR_VECTKEY_Pos)            /*!< SCB AIRCR: VECTKEY Mask */
+
+#define SCB_AIRCR_VECTKEYSTAT_Pos          16U                                            /*!< SCB AIRCR: VECTKEYSTAT Position */
+#define SCB_AIRCR_VECTKEYSTAT_Msk          (0xFFFFUL << SCB_AIRCR_VECTKEYSTAT_Pos)        /*!< SCB AIRCR: VECTKEYSTAT Mask */
+
+#define SCB_AIRCR_ENDIANESS_Pos            15U                                            /*!< SCB AIRCR: ENDIANESS Position */
+#define SCB_AIRCR_ENDIANESS_Msk            (1UL << SCB_AIRCR_ENDIANESS_Pos)               /*!< SCB AIRCR: ENDIANESS Mask */
+
+#define SCB_AIRCR_SYSRESETREQ_Pos           2U                                            /*!< SCB AIRCR: SYSRESETREQ Position */
+#define SCB_AIRCR_SYSRESETREQ_Msk          (1UL << SCB_AIRCR_SYSRESETREQ_Pos)             /*!< SCB AIRCR: SYSRESETREQ Mask */
+
+#define SCB_AIRCR_VECTCLRACTIVE_Pos         1U                                            /*!< SCB AIRCR: VECTCLRACTIVE Position */
+#define SCB_AIRCR_VECTCLRACTIVE_Msk        (1UL << SCB_AIRCR_VECTCLRACTIVE_Pos)           /*!< SCB AIRCR: VECTCLRACTIVE Mask */
+
+/* SCB System Control Register Definitions */
+#define SCB_SCR_SEVONPEND_Pos               4U                                            /*!< SCB SCR: SEVONPEND Position */
+#define SCB_SCR_SEVONPEND_Msk              (1UL << SCB_SCR_SEVONPEND_Pos)                 /*!< SCB SCR: SEVONPEND Mask */
+
+#define SCB_SCR_SLEEPDEEP_Pos               2U                                            /*!< SCB SCR: SLEEPDEEP Position */
+#define SCB_SCR_SLEEPDEEP_Msk              (1UL << SCB_SCR_SLEEPDEEP_Pos)                 /*!< SCB SCR: SLEEPDEEP Mask */
+
+#define SCB_SCR_SLEEPONEXIT_Pos             1U                                            /*!< SCB SCR: SLEEPONEXIT Position */
+#define SCB_SCR_SLEEPONEXIT_Msk            (1UL << SCB_SCR_SLEEPONEXIT_Pos)               /*!< SCB SCR: SLEEPONEXIT Mask */
+
+/* SCB Configuration Control Register Definitions */
+#define SCB_CCR_STKALIGN_Pos                9U                                            /*!< SCB CCR: STKALIGN Position */
+#define SCB_CCR_STKALIGN_Msk               (1UL << SCB_CCR_STKALIGN_Pos)                  /*!< SCB CCR: STKALIGN Mask */
+
+#define SCB_CCR_UNALIGN_TRP_Pos             3U                                            /*!< SCB CCR: UNALIGN_TRP Position */
+#define SCB_CCR_UNALIGN_TRP_Msk            (1UL << SCB_CCR_UNALIGN_TRP_Pos)               /*!< SCB CCR: UNALIGN_TRP Mask */
+
+/* SCB System Handler Control and State Register Definitions */
+#define SCB_SHCSR_SVCALLPENDED_Pos         15U                                            /*!< SCB SHCSR: SVCALLPENDED Position */
+#define SCB_SHCSR_SVCALLPENDED_Msk         (1UL << SCB_SHCSR_SVCALLPENDED_Pos)            /*!< SCB SHCSR: SVCALLPENDED Mask */
+
+/*@} end of group CMSIS_SCB */
+
+
+/**
+  \ingroup  CMSIS_core_register
+  \defgroup CMSIS_SCnSCB System Controls not in SCB (SCnSCB)
+  \brief    Type definitions for the System Control and ID Register not in the SCB
+  @{
+ */
+
+/**
+  \brief  Structure type to access the System Control and ID Register not in the SCB.
+ */
+typedef struct
+{
+        uint32_t RESERVED0[2U];
+  __IOM uint32_t ACTLR;                  /*!< Offset: 0x008 (R/W)  Auxiliary Control Register */
+} SCnSCB_Type;
+
+/* Auxiliary Control Register Definitions */
+#define SCnSCB_ACTLR_ITCMUAEN_Pos            4U                                        /*!< ACTLR: Instruction TCM Upper Alias Enable Position */
+#define SCnSCB_ACTLR_ITCMUAEN_Msk           (1UL << SCnSCB_ACTLR_ITCMUAEN_Pos)         /*!< ACTLR: Instruction TCM Upper Alias Enable Mask */
+
+#define SCnSCB_ACTLR_ITCMLAEN_Pos            3U                                        /*!< ACTLR: Instruction TCM Lower Alias Enable Position */
+#define SCnSCB_ACTLR_ITCMLAEN_Msk           (1UL << SCnSCB_ACTLR_ITCMLAEN_Pos)         /*!< ACTLR: Instruction TCM Lower Alias Enable Mask */
+
+/*@} end of group CMSIS_SCnotSCB */
+
+
+/**
+  \ingroup  CMSIS_core_register
+  \defgroup CMSIS_SysTick     System Tick Timer (SysTick)
+  \brief    Type definitions for the System Timer Registers.
+  @{
+ */
+
+/**
+  \brief  Structure type to access the System Timer (SysTick).
+ */
+typedef struct
+{
+  __IOM uint32_t CTRL;                   /*!< Offset: 0x000 (R/W)  SysTick Control and Status Register */
+  __IOM uint32_t LOAD;                   /*!< Offset: 0x004 (R/W)  SysTick Reload Value Register */
+  __IOM uint32_t VAL;                    /*!< Offset: 0x008 (R/W)  SysTick Current Value Register */
+  __IM  uint32_t CALIB;                  /*!< Offset: 0x00C (R/ )  SysTick Calibration Register */
+} SysTick_Type;
+
+/* SysTick Control / Status Register Definitions */
+#define SysTick_CTRL_COUNTFLAG_Pos         16U                                            /*!< SysTick CTRL: COUNTFLAG Position */
+#define SysTick_CTRL_COUNTFLAG_Msk         (1UL << SysTick_CTRL_COUNTFLAG_Pos)            /*!< SysTick CTRL: COUNTFLAG Mask */
+
+#define SysTick_CTRL_CLKSOURCE_Pos          2U                                            /*!< SysTick CTRL: CLKSOURCE Position */
+#define SysTick_CTRL_CLKSOURCE_Msk         (1UL << SysTick_CTRL_CLKSOURCE_Pos)            /*!< SysTick CTRL: CLKSOURCE Mask */
+
+#define SysTick_CTRL_TICKINT_Pos            1U                                            /*!< SysTick CTRL: TICKINT Position */
+#define SysTick_CTRL_TICKINT_Msk           (1UL << SysTick_CTRL_TICKINT_Pos)              /*!< SysTick CTRL: TICKINT Mask */
+
+#define SysTick_CTRL_ENABLE_Pos             0U                                            /*!< SysTick CTRL: ENABLE Position */
+#define SysTick_CTRL_ENABLE_Msk            (1UL /*<< SysTick_CTRL_ENABLE_Pos*/)           /*!< SysTick CTRL: ENABLE Mask */
+
+/* SysTick Reload Register Definitions */
+#define SysTick_LOAD_RELOAD_Pos             0U                                            /*!< SysTick LOAD: RELOAD Position */
+#define SysTick_LOAD_RELOAD_Msk            (0xFFFFFFUL /*<< SysTick_LOAD_RELOAD_Pos*/)    /*!< SysTick LOAD: RELOAD Mask */
+
+/* SysTick Current Register Definitions */
+#define SysTick_VAL_CURRENT_Pos             0U                                            /*!< SysTick VAL: CURRENT Position */
+#define SysTick_VAL_CURRENT_Msk            (0xFFFFFFUL /*<< SysTick_VAL_CURRENT_Pos*/)    /*!< SysTick VAL: CURRENT Mask */
+
+/* SysTick Calibration Register Definitions */
+#define SysTick_CALIB_NOREF_Pos            31U                                            /*!< SysTick CALIB: NOREF Position */
+#define SysTick_CALIB_NOREF_Msk            (1UL << SysTick_CALIB_NOREF_Pos)               /*!< SysTick CALIB: NOREF Mask */
+
+#define SysTick_CALIB_SKEW_Pos             30U                                            /*!< SysTick CALIB: SKEW Position */
+#define SysTick_CALIB_SKEW_Msk             (1UL << SysTick_CALIB_SKEW_Pos)                /*!< SysTick CALIB: SKEW Mask */
+
+#define SysTick_CALIB_TENMS_Pos             0U                                            /*!< SysTick CALIB: TENMS Position */
+#define SysTick_CALIB_TENMS_Msk            (0xFFFFFFUL /*<< SysTick_CALIB_TENMS_Pos*/)    /*!< SysTick CALIB: TENMS Mask */
+
+/*@} end of group CMSIS_SysTick */
+
+
+/**
+  \ingroup  CMSIS_core_register
+  \defgroup CMSIS_CoreDebug       Core Debug Registers (CoreDebug)
+  \brief    Cortex-M1 Core Debug Registers (DCB registers, SHCSR, and DFSR) are only accessible over DAP and not via processor.
+            Therefore they are not covered by the Cortex-M1 header file.
+  @{
+ */
+/*@} end of group CMSIS_CoreDebug */
+
+
+/**
+  \ingroup    CMSIS_core_register
+  \defgroup   CMSIS_core_bitfield     Core register bit field macros
+  \brief      Macros for use with bit field definitions (xxx_Pos, xxx_Msk).
+  @{
+ */
+
+/**
+  \brief   Mask and shift a bit field value for use in a register bit range.
+  \param[in] field  Name of the register bit field.
+  \param[in] value  Value of the bit field. This parameter is interpreted as an uint32_t type.
+  \return           Masked and shifted value.
+*/
+#define _VAL2FLD(field, value)    (((uint32_t)(value) << field ## _Pos) & field ## _Msk)
+
+/**
+  \brief     Mask and shift a register value to extract a bit filed value.
+  \param[in] field  Name of the register bit field.
+  \param[in] value  Value of register. This parameter is interpreted as an uint32_t type.
+  \return           Masked and shifted bit field value.
+*/
+#define _FLD2VAL(field, value)    (((uint32_t)(value) & field ## _Msk) >> field ## _Pos)
+
+/*@} end of group CMSIS_core_bitfield */
+
+
+/**
+  \ingroup    CMSIS_core_register
+  \defgroup   CMSIS_core_base     Core Definitions
+  \brief      Definitions for base addresses, unions, and structures.
+  @{
+ */
+
+/* Memory mapping of Core Hardware */
+#define SCS_BASE            (0xE000E000UL)                            /*!< System Control Space Base Address */
+#define SysTick_BASE        (SCS_BASE +  0x0010UL)                    /*!< SysTick Base Address */
+#define NVIC_BASE           (SCS_BASE +  0x0100UL)                    /*!< NVIC Base Address */
+#define SCB_BASE            (SCS_BASE +  0x0D00UL)                    /*!< System Control Block Base Address */
+
+#define SCnSCB              ((SCnSCB_Type    *)     SCS_BASE      )   /*!< System control Register not in SCB */
+#define SCB                 ((SCB_Type       *)     SCB_BASE      )   /*!< SCB configuration struct */
+#define SysTick             ((SysTick_Type   *)     SysTick_BASE  )   /*!< SysTick configuration struct */
+#define NVIC                ((NVIC_Type      *)     NVIC_BASE     )   /*!< NVIC configuration struct */
+
+
+/*@} */
+
+
+
+/*******************************************************************************
+ *                Hardware Abstraction Layer
+  Core Function Interface contains:
+  - Core NVIC Functions
+  - Core SysTick Functions
+  - Core Register Access Functions
+ ******************************************************************************/
+/**
+  \defgroup CMSIS_Core_FunctionInterface Functions and Instructions Reference
+*/
+
+
+
+/* ##########################   NVIC functions  #################################### */
+/**
+  \ingroup  CMSIS_Core_FunctionInterface
+  \defgroup CMSIS_Core_NVICFunctions NVIC Functions
+  \brief    Functions that manage interrupts and exceptions via the NVIC.
+  @{
+ */
+
+#ifdef CMSIS_NVIC_VIRTUAL
+  #ifndef CMSIS_NVIC_VIRTUAL_HEADER_FILE
+    #define CMSIS_NVIC_VIRTUAL_HEADER_FILE "cmsis_nvic_virtual.h"
+  #endif
+  #include CMSIS_NVIC_VIRTUAL_HEADER_FILE
+#else
+  #define NVIC_SetPriorityGrouping    __NVIC_SetPriorityGrouping
+  #define NVIC_GetPriorityGrouping    __NVIC_GetPriorityGrouping
+  #define NVIC_EnableIRQ              __NVIC_EnableIRQ
+  #define NVIC_GetEnableIRQ           __NVIC_GetEnableIRQ
+  #define NVIC_DisableIRQ             __NVIC_DisableIRQ
+  #define NVIC_GetPendingIRQ          __NVIC_GetPendingIRQ
+  #define NVIC_SetPendingIRQ          __NVIC_SetPendingIRQ
+  #define NVIC_ClearPendingIRQ        __NVIC_ClearPendingIRQ
+/*#define NVIC_GetActive              __NVIC_GetActive             not available for Cortex-M1 */
+  #define NVIC_SetPriority            __NVIC_SetPriority
+  #define NVIC_GetPriority            __NVIC_GetPriority
+  #define NVIC_SystemReset            __NVIC_SystemReset
+#endif /* CMSIS_NVIC_VIRTUAL */
+
+#ifdef CMSIS_VECTAB_VIRTUAL
+  #ifndef CMSIS_VECTAB_VIRTUAL_HEADER_FILE
+    #define CMSIS_VECTAB_VIRTUAL_HEADER_FILE "cmsis_vectab_virtual.h"
+  #endif
+  #include CMSIS_VECTAB_VIRTUAL_HEADER_FILE
+#else
+  #define NVIC_SetVector              __NVIC_SetVector
+  #define NVIC_GetVector              __NVIC_GetVector
+#endif  /* (CMSIS_VECTAB_VIRTUAL) */
+
+#define NVIC_USER_IRQ_OFFSET          16
+
+
+/* The following EXC_RETURN values are saved the LR on exception entry */
+#define EXC_RETURN_HANDLER         (0xFFFFFFF1UL)     /* return to Handler mode, uses MSP after return                               */
+#define EXC_RETURN_THREAD_MSP      (0xFFFFFFF9UL)     /* return to Thread mode, uses MSP after return                                */
+#define EXC_RETURN_THREAD_PSP      (0xFFFFFFFDUL)     /* return to Thread mode, uses PSP after return                                */
+
+
+/* Interrupt Priorities are WORD accessible only under Armv6-M                  */
+/* The following MACROS handle generation of the register offset and byte masks */
+#define _BIT_SHIFT(IRQn)         (  ((((uint32_t)(int32_t)(IRQn))         )      &  0x03UL) * 8UL)
+#define _SHP_IDX(IRQn)           ( (((((uint32_t)(int32_t)(IRQn)) & 0x0FUL)-8UL) >>    2UL)      )
+#define _IP_IDX(IRQn)            (   (((uint32_t)(int32_t)(IRQn))                >>    2UL)      )
+
+#define __NVIC_SetPriorityGrouping(X) (void)(X)
+#define __NVIC_GetPriorityGrouping()  (0U)
+
+/**
+  \brief   Enable Interrupt
+  \details Enables a device specific interrupt in the NVIC interrupt controller.
+  \param [in]      IRQn  Device specific interrupt number.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE void __NVIC_EnableIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    NVIC->ISER[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL));
+  }
+}
+
+
+/**
+  \brief   Get Interrupt Enable status
+  \details Returns a device specific interrupt enable status from the NVIC interrupt controller.
+  \param [in]      IRQn  Device specific interrupt number.
+  \return             0  Interrupt is not enabled.
+  \return             1  Interrupt is enabled.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE uint32_t __NVIC_GetEnableIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    return((uint32_t)(((NVIC->ISER[0U] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL));
+  }
+  else
+  {
+    return(0U);
+  }
+}
+
+
+/**
+  \brief   Disable Interrupt
+  \details Disables a device specific interrupt in the NVIC interrupt controller.
+  \param [in]      IRQn  Device specific interrupt number.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE void __NVIC_DisableIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    NVIC->ICER[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL));
+    __DSB();
+    __ISB();
+  }
+}
+
+
+/**
+  \brief   Get Pending Interrupt
+  \details Reads the NVIC pending register and returns the pending bit for the specified device specific interrupt.
+  \param [in]      IRQn  Device specific interrupt number.
+  \return             0  Interrupt status is not pending.
+  \return             1  Interrupt status is pending.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE uint32_t __NVIC_GetPendingIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    return((uint32_t)(((NVIC->ISPR[0U] & (1UL << (((uint32_t)IRQn) & 0x1FUL))) != 0UL) ? 1UL : 0UL));
+  }
+  else
+  {
+    return(0U);
+  }
+}
+
+
+/**
+  \brief   Set Pending Interrupt
+  \details Sets the pending bit of a device specific interrupt in the NVIC pending register.
+  \param [in]      IRQn  Device specific interrupt number.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE void __NVIC_SetPendingIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    NVIC->ISPR[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL));
+  }
+}
+
+
+/**
+  \brief   Clear Pending Interrupt
+  \details Clears the pending bit of a device specific interrupt in the NVIC pending register.
+  \param [in]      IRQn  Device specific interrupt number.
+  \note    IRQn must not be negative.
+ */
+__STATIC_INLINE void __NVIC_ClearPendingIRQ(IRQn_Type IRQn)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    NVIC->ICPR[0U] = (uint32_t)(1UL << (((uint32_t)IRQn) & 0x1FUL));
+  }
+}
+
+
+/**
+  \brief   Set Interrupt Priority
+  \details Sets the priority of a device specific interrupt or a processor exception.
+           The interrupt number can be positive to specify a device specific interrupt,
+           or negative to specify a processor exception.
+  \param [in]      IRQn  Interrupt number.
+  \param [in]  priority  Priority to set.
+  \note    The priority cannot be set for every processor exception.
+ */
+__STATIC_INLINE void __NVIC_SetPriority(IRQn_Type IRQn, uint32_t priority)
+{
+  if ((int32_t)(IRQn) >= 0)
+  {
+    NVIC->IP[_IP_IDX(IRQn)]  = ((uint32_t)(NVIC->IP[_IP_IDX(IRQn)]  & ~(0xFFUL << _BIT_SHIFT(IRQn))) |
+       (((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL) << _BIT_SHIFT(IRQn)));
+  }
+  else
+  {
+    SCB->SHP[_SHP_IDX(IRQn)] = ((uint32_t)(SCB->SHP[_SHP_IDX(IRQn)] & ~(0xFFUL << _BIT_SHIFT(IRQn))) |
+       (((priority << (8U - __NVIC_PRIO_BITS)) & (uint32_t)0xFFUL) << _BIT_SHIFT(IRQn)));
+  }
+}
+
+
+/**
+  \brief   Get Interrupt Priority
+  \details Reads the priority of a device specific interrupt or a processor exception.
+           The interrupt number can be positive to specify a device specific interrupt,
+           or negative to specify a processor exception.
+  \param [in]   IRQn  Interrupt number.
+  \return             Interrupt Priority.
+                      Value is aligned automatically to the implemented priority bits of the microcontroller.
+ */
+__STATIC_INLINE uint32_t __NVIC_GetPriority(IRQn_Type IRQn)
+{
+
+  if ((int32_t)(IRQn) >= 0)
+  {
+    return((uint32_t)(((NVIC->IP[ _IP_IDX(IRQn)] >> _BIT_SHIFT(IRQn) ) & (uint32_t)0xFFUL) >> (8U - __NVIC_PRIO_BITS)));
+  }
+  else
+  {
+    return((uint32_t)(((SCB->SHP[_SHP_IDX(IRQn)] >> _BIT_SHIFT(IRQn) ) & (uint32_t)0xFFUL) >> (8U - __NVIC_PRIO_BITS)));
+  }
+}
+
+
+/**
+  \brief   Encode Priority
+  \details Encodes the priority for an interrupt with the given priority group,
+           preemptive priority value, and subpriority value.
+           In case of a conflict between priority grouping and available
+           priority bits (__NVIC_PRIO_BITS), the smallest possible priority group is set.
+  \param [in]     PriorityGroup  Used priority group.
+  \param [in]   PreemptPriority  Preemptive priority value (starting from 0).
+  \param [in]       SubPriority  Subpriority value (starting from 0).
+  \return                        Encoded priority. Value can be used in the function \ref NVIC_SetPriority().
+ */
+__STATIC_INLINE uint32_t NVIC_EncodePriority (uint32_t PriorityGroup, uint32_t PreemptPriority, uint32_t SubPriority)
+{
+  uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL);   /* only values 0..7 are used          */
+  uint32_t PreemptPriorityBits;
+  uint32_t SubPriorityBits;
+
+  PreemptPriorityBits = ((7UL - PriorityGroupTmp) > (uint32_t)(__NVIC_PRIO_BITS)) ? (uint32_t)(__NVIC_PRIO_BITS) : (uint32_t)(7UL - PriorityGroupTmp);
+  SubPriorityBits     = ((PriorityGroupTmp + (uint32_t)(__NVIC_PRIO_BITS)) < (uint32_t)7UL) ? (uint32_t)0UL : (uint32_t)((PriorityGroupTmp - 7UL) + (uint32_t)(__NVIC_PRIO_BITS));
+
+  return (
+           ((PreemptPriority & (uint32_t)((1UL << (PreemptPriorityBits)) - 1UL)) << SubPriorityBits) |
+           ((SubPriority     & (uint32_t)((1UL << (SubPriorityBits    )) - 1UL)))
+         );
+}
+
+
+/**
+  \brief   Decode Priority
+  \details Decodes an interrupt priority value with a given priority group to
+           preemptive priority value and subpriority value.
+           In case of a conflict between priority grouping and available
+           priority bits (__NVIC_PRIO_BITS) the smallest possible priority group is set.
+  \param [in]         Priority   Priority value, which can be retrieved with the function \ref NVIC_GetPriority().
+  \param [in]     PriorityGroup  Used priority group.
+  \param [out] pPreemptPriority  Preemptive priority value (starting from 0).
+  \param [out]     pSubPriority  Subpriority value (starting from 0).
+ */
+__STATIC_INLINE void NVIC_DecodePriority (uint32_t Priority, uint32_t PriorityGroup, uint32_t* const pPreemptPriority, uint32_t* const pSubPriority)
+{
+  uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07UL);   /* only values 0..7 are used          */
+  uint32_t PreemptPriorityBits;
+  uint32_t SubPriorityBits;
+
+  PreemptPriorityBits = ((7UL - PriorityGroupTmp) > (uint32_t)(__NVIC_PRIO_BITS)) ? (uint32_t)(__NVIC_PRIO_BITS) : (uint32_t)(7UL - PriorityGroupTmp);
+  SubPriorityBits     = ((PriorityGroupTmp + (uint32_t)(__NVIC_PRIO_BITS)) < (uint32_t)7UL) ? (uint32_t)0UL : (uint32_t)((PriorityGroupTmp - 7UL) + (uint32_t)(__NVIC_PRIO_BITS));
+
+  *pPreemptPriority = (Priority >> SubPriorityBits) & (uint32_t)((1UL << (PreemptPriorityBits)) - 1UL);
+  *pSubPriority     = (Priority                   ) & (uint32_t)((1UL << (SubPriorityBits    )) - 1UL);
+}
+
+
+
+/**
+  \brief   Set Interrupt Vector
+  \details Sets an interrupt vector in SRAM based interrupt vector table.
+           The interrupt number can be positive to specify a device specific interrupt,
+           or negative to specify a processor exception.
+           Address 0 must be mapped to SRAM.
+  \param [in]   IRQn      Interrupt number
+  \param [in]   vector    Address of interrupt handler function
+ */
+__STATIC_INLINE void __NVIC_SetVector(IRQn_Type IRQn, uint32_t vector)
+{
+  uint32_t *vectors = (uint32_t *)0x0U;
+  vectors[(int32_t)IRQn + NVIC_USER_IRQ_OFFSET] = vector;
+}
+
+
+/**
+  \brief   Get Interrupt Vector
+  \details Reads an interrupt vector from interrupt vector table.
+           The interrupt number can be positive to specify a device specific interrupt,
+           or negative to specify a processor exception.
+  \param [in]   IRQn      Interrupt number.
+  \return                 Address of interrupt handler function
+ */
+__STATIC_INLINE uint32_t __NVIC_GetVector(IRQn_Type IRQn)
+{
+  uint32_t *vectors = (uint32_t *)0x0U;
+  return vectors[(int32_t)IRQn + NVIC_USER_IRQ_OFFSET];
+}
+
+
+/**
+  \brief   System Reset
+  \details Initiates a system reset request to reset the MCU.
+ */
+__NO_RETURN __STATIC_INLINE void __NVIC_SystemReset(void)
+{
+  __DSB();                                                          /* Ensure all outstanding memory accesses included
+                                                                       buffered write are completed before reset */
+  SCB->AIRCR  = ((0x5FAUL << SCB_AIRCR_VECTKEY_Pos) |
+                 SCB_AIRCR_SYSRESETREQ_Msk);
+  __DSB();                                                          /* Ensure completion of memory access */
+
+  for(;;)                                                           /* wait until reset */
+  {
+    __NOP();
+  }
+}
+
+/*@} end of CMSIS_Core_NVICFunctions */
+
+
+/* ##########################  FPU functions  #################################### */
+/**
+  \ingroup  CMSIS_Core_FunctionInterface
+  \defgroup CMSIS_Core_FpuFunctions FPU Functions
+  \brief    Function that provides FPU type.
+  @{
+ */
+
+/**
+  \brief   get FPU type
+  \details returns the FPU type
+  \returns
+   - \b  0: No FPU
+   - \b  1: Single precision FPU
+   - \b  2: Double + Single precision FPU
+ */
+__STATIC_INLINE uint32_t SCB_GetFPUType(void)
+{
+    return 0U;           /* No FPU */
+}
+
+
+/*@} end of CMSIS_Core_FpuFunctions */
+
+
+
+/* ##################################    SysTick function  ############################################ */
+/**
+  \ingroup  CMSIS_Core_FunctionInterface
+  \defgroup CMSIS_Core_SysTickFunctions SysTick Functions
+  \brief    Functions that configure the System.
+  @{
+ */
+
+#if defined (__Vendor_SysTickConfig) && (__Vendor_SysTickConfig == 0U)
+
+/**
+  \brief   System Tick Configuration
+  \details Initializes the System Timer and its interrupt, and starts the System Tick Timer.
+           Counter is in free running mode to generate periodic interrupts.
+  \param [in]  ticks  Number of ticks between two interrupts.
+  \return          0  Function succeeded.
+  \return          1  Function failed.
+  \note    When the variable <b>__Vendor_SysTickConfig</b> is set to 1, then the
+           function <b>SysTick_Config</b> is not included. In this case, the file <b><i>device</i>.h</b>
+           must contain a vendor-specific implementation of this function.
+ */
+__STATIC_INLINE uint32_t SysTick_Config(uint32_t ticks)
+{
+  if ((ticks - 1UL) > SysTick_LOAD_RELOAD_Msk)
+  {
+    return (1UL);                                                   /* Reload value impossible */
+  }
+
+  SysTick->LOAD  = (uint32_t)(ticks - 1UL);                         /* set reload register */
+  NVIC_SetPriority (SysTick_IRQn, (1UL << __NVIC_PRIO_BITS) - 1UL); /* set Priority for Systick Interrupt */
+  SysTick->VAL   = 0UL;                                             /* Load the SysTick Counter Value */
+  SysTick->CTRL  = SysTick_CTRL_CLKSOURCE_Msk |
+                   SysTick_CTRL_TICKINT_Msk   |
+                   SysTick_CTRL_ENABLE_Msk;                         /* Enable SysTick IRQ and SysTick Timer */
+  return (0UL);                                                     /* Function successful */
+}
+
+#endif
+
+/*@} end of CMSIS_Core_SysTickFunctions */
+
+
+
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __CORE_CM1_H_DEPENDANT */
+
+#endif /* __CMSIS_GENERIC */

Drivers/CMSIS/Include/mpu_armv7.h

@@ -0,0 +1,270 @@
+/******************************************************************************
+ * @file     mpu_armv7.h
+ * @brief    CMSIS MPU API for Armv7-M MPU
+ * @version  V5.0.4
+ * @date     10. January 2018
+ ******************************************************************************/
+/*
+ * Copyright (c) 2017-2018 Arm Limited. All rights reserved.
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the License); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an AS IS BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+ 
+#if   defined ( __ICCARM__ )
+  #pragma system_include         /* treat file as system include file for MISRA check */
+#elif defined (__clang__)
+  #pragma clang system_header    /* treat file as system include file */
+#endif
+ 
+#ifndef ARM_MPU_ARMV7_H
+#define ARM_MPU_ARMV7_H
+
+#define ARM_MPU_REGION_SIZE_32B      ((uint8_t)0x04U) ///!< MPU Region Size 32 Bytes
+#define ARM_MPU_REGION_SIZE_64B      ((uint8_t)0x05U) ///!< MPU Region Size 64 Bytes
+#define ARM_MPU_REGION_SIZE_128B     ((uint8_t)0x06U) ///!< MPU Region Size 128 Bytes
+#define ARM_MPU_REGION_SIZE_256B     ((uint8_t)0x07U) ///!< MPU Region Size 256 Bytes
+#define ARM_MPU_REGION_SIZE_512B     ((uint8_t)0x08U) ///!< MPU Region Size 512 Bytes
+#define ARM_MPU_REGION_SIZE_1KB      ((uint8_t)0x09U) ///!< MPU Region Size 1 KByte
+#define ARM_MPU_REGION_SIZE_2KB      ((uint8_t)0x0AU) ///!< MPU Region Size 2 KBytes
+#define ARM_MPU_REGION_SIZE_4KB      ((uint8_t)0x0BU) ///!< MPU Region Size 4 KBytes
+#define ARM_MPU_REGION_SIZE_8KB      ((uint8_t)0x0CU) ///!< MPU Region Size 8 KBytes
+#define ARM_MPU_REGION_SIZE_16KB     ((uint8_t)0x0DU) ///!< MPU Region Size 16 KBytes
+#define ARM_MPU_REGION_SIZE_32KB     ((uint8_t)0x0EU) ///!< MPU Region Size 32 KBytes
+#define ARM_MPU_REGION_SIZE_64KB     ((uint8_t)0x0FU) ///!< MPU Region Size 64 KBytes
+#define ARM_MPU_REGION_SIZE_128KB    ((uint8_t)0x10U) ///!< MPU Region Size 128 KBytes
+#define ARM_MPU_REGION_SIZE_256KB    ((uint8_t)0x11U) ///!< MPU Region Size 256 KBytes
+#define ARM_MPU_REGION_SIZE_512KB    ((uint8_t)0x12U) ///!< MPU Region Size 512 KBytes
+#define ARM_MPU_REGION_SIZE_1MB      ((uint8_t)0x13U) ///!< MPU Region Size 1 MByte
+#define ARM_MPU_REGION_SIZE_2MB      ((uint8_t)0x14U) ///!< MPU Region Size 2 MBytes
+#define ARM_MPU_REGION_SIZE_4MB      ((uint8_t)0x15U) ///!< MPU Region Size 4 MBytes
+#define ARM_MPU_REGION_SIZE_8MB      ((uint8_t)0x16U) ///!< MPU Region Size 8 MBytes
+#define ARM_MPU_REGION_SIZE_16MB     ((uint8_t)0x17U) ///!< MPU Region Size 16 MBytes
+#define ARM_MPU_REGION_SIZE_32MB     ((uint8_t)0x18U) ///!< MPU Region Size 32 MBytes
+#define ARM_MPU_REGION_SIZE_64MB     ((uint8_t)0x19U) ///!< MPU Region Size 64 MBytes
+#define ARM_MPU_REGION_SIZE_128MB    ((uint8_t)0x1AU) ///!< MPU Region Size 128 MBytes
+#define ARM_MPU_REGION_SIZE_256MB    ((uint8_t)0x1BU) ///!< MPU Region Size 256 MBytes
+#define ARM_MPU_REGION_SIZE_512MB    ((uint8_t)0x1CU) ///!< MPU Region Size 512 MBytes
+#define ARM_MPU_REGION_SIZE_1GB      ((uint8_t)0x1DU) ///!< MPU Region Size 1 GByte
+#define ARM_MPU_REGION_SIZE_2GB      ((uint8_t)0x1EU) ///!< MPU Region Size 2 GBytes
+#define ARM_MPU_REGION_SIZE_4GB      ((uint8_t)0x1FU) ///!< MPU Region Size 4 GBytes
+
+#define ARM_MPU_AP_NONE 0U ///!< MPU Access Permission no access
+#define ARM_MPU_AP_PRIV 1U ///!< MPU Access Permission privileged access only
+#define ARM_MPU_AP_URO  2U ///!< MPU Access Permission unprivileged access read-only
+#define ARM_MPU_AP_FULL 3U ///!< MPU Access Permission full access
+#define ARM_MPU_AP_PRO  5U ///!< MPU Access Permission privileged access read-only
+#define ARM_MPU_AP_RO   6U ///!< MPU Access Permission read-only access
+
+/** MPU Region Base Address Register Value
+*
+* \param Region The region to be configured, number 0 to 15.
+* \param BaseAddress The base address for the region.
+*/
+#define ARM_MPU_RBAR(Region, BaseAddress) \
+  (((BaseAddress) & MPU_RBAR_ADDR_Msk) |  \
+   ((Region) & MPU_RBAR_REGION_Msk)    |  \
+   (MPU_RBAR_VALID_Msk))
+
+/**
+* MPU Memory Access Attributes
+* 
+* \param TypeExtField      Type extension field, allows you to configure memory access type, for example strongly ordered, peripheral.
+* \param IsShareable       Region is shareable between multiple bus masters.
+* \param IsCacheable       Region is cacheable, i.e. its value may be kept in cache.
+* \param IsBufferable      Region is bufferable, i.e. using write-back caching. Cacheable but non-bufferable regions use write-through policy.
+*/  
+#define ARM_MPU_ACCESS_(TypeExtField, IsShareable, IsCacheable, IsBufferable)   \
+  ((((TypeExtField ) << MPU_RASR_TEX_Pos) & MPU_RASR_TEX_Msk)                 | \
+   (((IsShareable ) << MPU_RASR_S_Pos) & MPU_RASR_S_Msk)                      | \
+   (((IsCacheable ) << MPU_RASR_C_Pos) & MPU_RASR_C_Msk)                      | \
+   (((IsBufferable ) << MPU_RASR_B_Pos) & MPU_RASR_B_Msk))
+
+/**
+* MPU Region Attribute and Size Register Value
+* 
+* \param DisableExec       Instruction access disable bit, 1= disable instruction fetches.
+* \param AccessPermission  Data access permissions, allows you to configure read/write access for User and Privileged mode.
+* \param AccessAttributes  Memory access attribution, see \ref ARM_MPU_ACCESS_.
+* \param SubRegionDisable  Sub-region disable field.
+* \param Size              Region size of the region to be configured, for example 4K, 8K.
+*/
+#define ARM_MPU_RASR_EX(DisableExec, AccessPermission, AccessAttributes, SubRegionDisable, Size)      \
+  ((((DisableExec ) << MPU_RASR_XN_Pos) & MPU_RASR_XN_Msk)                                          | \
+   (((AccessPermission) << MPU_RASR_AP_Pos) & MPU_RASR_AP_Msk)                                      | \
+   (((AccessAttributes) ) & (MPU_RASR_TEX_Msk | MPU_RASR_S_Msk | MPU_RASR_C_Msk | MPU_RASR_B_Msk)))
+  
+/**
+* MPU Region Attribute and Size Register Value
+* 
+* \param DisableExec       Instruction access disable bit, 1= disable instruction fetches.
+* \param AccessPermission  Data access permissions, allows you to configure read/write access for User and Privileged mode.
+* \param TypeExtField      Type extension field, allows you to configure memory access type, for example strongly ordered, peripheral.
+* \param IsShareable       Region is shareable between multiple bus masters.
+* \param IsCacheable       Region is cacheable, i.e. its value may be kept in cache.
+* \param IsBufferable      Region is bufferable, i.e. using write-back caching. Cacheable but non-bufferable regions use write-through policy.
+* \param SubRegionDisable  Sub-region disable field.
+* \param Size              Region size of the region to be configured, for example 4K, 8K.
+*/                         
+#define ARM_MPU_RASR(DisableExec, AccessPermission, TypeExtField, IsShareable, IsCacheable, IsBufferable, SubRegionDisable, Size) \
+  ARM_MPU_RASR_EX(DisableExec, AccessPermission, ARM_MPU_ACCESS_(TypeExtField, IsShareable, IsCacheable, IsBufferable), SubRegionDisable, Size)
+
+/**
+* MPU Memory Access Attribute for strongly ordered memory.
+*  - TEX: 000b
+*  - Shareable
+*  - Non-cacheable
+*  - Non-bufferable
+*/ 
+#define ARM_MPU_ACCESS_ORDERED ARM_MPU_ACCESS_(0U, 1U, 0U, 0U)
+
+/**
+* MPU Memory Access Attribute for device memory.
+*  - TEX: 000b (if non-shareable) or 010b (if shareable)
+*  - Shareable or non-shareable
+*  - Non-cacheable
+*  - Bufferable (if shareable) or non-bufferable (if non-shareable)
+*
+* \param IsShareable Configures the device memory as shareable or non-shareable.
+*/ 
+#define ARM_MPU_ACCESS_DEVICE(IsShareable) ((IsShareable) ? ARM_MPU_ACCESS_(0U, 1U, 0U, 1U) : ARM_MPU_ACCESS_(2U, 0U, 0U, 0U))
+
+/**
+* MPU Memory Access Attribute for normal memory.
+*  - TEX: 1BBb (reflecting outer cacheability rules)
+*  - Shareable or non-shareable
+*  - Cacheable or non-cacheable (reflecting inner cacheability rules)
+*  - Bufferable or non-bufferable (reflecting inner cacheability rules)
+*
+* \param OuterCp Configures the outer cache policy.
+* \param InnerCp Configures the inner cache policy.
+* \param IsShareable Configures the memory as shareable or non-shareable.
+*/ 
+#define ARM_MPU_ACCESS_NORMAL(OuterCp, InnerCp, IsShareable) ARM_MPU_ACCESS_((4U | (OuterCp)), IsShareable, ((InnerCp) & 2U), ((InnerCp) & 1U))
+
+/**
+* MPU Memory Access Attribute non-cacheable policy.
+*/
+#define ARM_MPU_CACHEP_NOCACHE 0U
+
+/**
+* MPU Memory Access Attribute write-back, write and read allocate policy.
+*/
+#define ARM_MPU_CACHEP_WB_WRA 1U
+
+/**
+* MPU Memory Access Attribute write-through, no write allocate policy.
+*/
+#define ARM_MPU_CACHEP_WT_NWA 2U
+
+/**
+* MPU Memory Access Attribute write-back, no write allocate policy.
+*/
+#define ARM_MPU_CACHEP_WB_NWA 3U
+
+
+/**
+* Struct for a single MPU Region
+*/
+typedef struct {
+  uint32_t RBAR; //!< The region base address register value (RBAR)
+  uint32_t RASR; //!< The region attribute and size register value (RASR) \ref MPU_RASR
+} ARM_MPU_Region_t;
+    
+/** Enable the MPU.
+* \param MPU_Control Default access permissions for unconfigured regions.
+*/
+__STATIC_INLINE void ARM_MPU_Enable(uint32_t MPU_Control)
+{
+  __DSB();
+  __ISB();
+  MPU->CTRL = MPU_Control | MPU_CTRL_ENABLE_Msk;
+#ifdef SCB_SHCSR_MEMFAULTENA_Msk
+  SCB->SHCSR |= SCB_SHCSR_MEMFAULTENA_Msk;
+#endif
+}
+
+/** Disable the MPU.
+*/
+__STATIC_INLINE void ARM_MPU_Disable(void)
+{
+  __DSB();
+  __ISB();
+#ifdef SCB_SHCSR_MEMFAULTENA_Msk
+  SCB->SHCSR &= ~SCB_SHCSR_MEMFAULTENA_Msk;
+#endif
+  MPU->CTRL  &= ~MPU_CTRL_ENABLE_Msk;
+}
+
+/** Clear and disable the given MPU region.
+* \param rnr Region number to be cleared.
+*/
+__STATIC_INLINE void ARM_MPU_ClrRegion(uint32_t rnr)
+{
+  MPU->RNR = rnr;
+  MPU->RASR = 0U;
+}
+
+/** Configure an MPU region.
+* \param rbar Value for RBAR register.
+* \param rsar Value for RSAR register.
+*/   
+__STATIC_INLINE void ARM_MPU_SetRegion(uint32_t rbar, uint32_t rasr)
+{
+  MPU->RBAR = rbar;
+  MPU->RASR = rasr;
+}
+
+/** Configure the given MPU region.
+* \param rnr Region number to be configured.
+* \param rbar Value for RBAR register.
+* \param rsar Value for RSAR register.
+*/   
+__STATIC_INLINE void ARM_MPU_SetRegionEx(uint32_t rnr, uint32_t rbar, uint32_t rasr)
+{
+  MPU->RNR = rnr;
+  MPU->RBAR = rbar;
+  MPU->RASR = rasr;
+}
+
+/** Memcopy with strictly ordered memory access, e.g. for register targets.
+* \param dst Destination data is copied to.
+* \param src Source data is copied from.
+* \param len Amount of data words to be copied.
+*/
+__STATIC_INLINE void orderedCpy(volatile uint32_t* dst, const uint32_t* __RESTRICT src, uint32_t len)
+{
+  uint32_t i;
+  for (i = 0U; i < len; ++i) 
+  {
+    dst[i] = src[i];
+  }
+}
+
+/** Load the given number of MPU regions from a table.
+* \param table Pointer to the MPU configuration table.
+* \param cnt Amount of regions to be configured.
+*/
+__STATIC_INLINE void ARM_MPU_Load(ARM_MPU_Region_t const* table, uint32_t cnt) 
+{
+  const uint32_t rowWordSize = sizeof(ARM_MPU_Region_t)/4U;
+  while (cnt > MPU_TYPE_RALIASES) {
+    orderedCpy(&(MPU->RBAR), &(table->RBAR), MPU_TYPE_RALIASES*rowWordSize);
+    table += MPU_TYPE_RALIASES;
+    cnt -= MPU_TYPE_RALIASES;
+  }
+  orderedCpy(&(MPU->RBAR), &(table->RBAR), cnt*rowWordSize);
+}
+
+#endif

Drivers/CMSIS/Include/mpu_armv8.h

@@ -0,0 +1,333 @@
+/******************************************************************************
+ * @file     mpu_armv8.h
+ * @brief    CMSIS MPU API for Armv8-M MPU
+ * @version  V5.0.4
+ * @date     10. January 2018
+ ******************************************************************************/
+/*
+ * Copyright (c) 2017-2018 Arm Limited. All rights reserved.
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the License); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an AS IS BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#if   defined ( __ICCARM__ )
+  #pragma system_include         /* treat file as system include file for MISRA check */
+#elif defined (__clang__)
+  #pragma clang system_header    /* treat file as system include file */
+#endif
+
+#ifndef ARM_MPU_ARMV8_H
+#define ARM_MPU_ARMV8_H
+
+/** \brief Attribute for device memory (outer only) */
+#define ARM_MPU_ATTR_DEVICE                           ( 0U )
+
+/** \brief Attribute for non-cacheable, normal memory */
+#define ARM_MPU_ATTR_NON_CACHEABLE                    ( 4U )
+
+/** \brief Attribute for normal memory (outer and inner)
+* \param NT Non-Transient: Set to 1 for non-transient data.
+* \param WB Write-Back: Set to 1 to use write-back update policy.
+* \param RA Read Allocation: Set to 1 to use cache allocation on read miss.
+* \param WA Write Allocation: Set to 1 to use cache allocation on write miss.
+*/
+#define ARM_MPU_ATTR_MEMORY_(NT, WB, RA, WA) \
+  (((NT & 1U) << 3U) | ((WB & 1U) << 2U) | ((RA & 1U) << 1U) | (WA & 1U))
+
+/** \brief Device memory type non Gathering, non Re-ordering, non Early Write Acknowledgement */
+#define ARM_MPU_ATTR_DEVICE_nGnRnE (0U)
+
+/** \brief Device memory type non Gathering, non Re-ordering, Early Write Acknowledgement */
+#define ARM_MPU_ATTR_DEVICE_nGnRE  (1U)
+
+/** \brief Device memory type non Gathering, Re-ordering, Early Write Acknowledgement */
+#define ARM_MPU_ATTR_DEVICE_nGRE   (2U)
+
+/** \brief Device memory type Gathering, Re-ordering, Early Write Acknowledgement */
+#define ARM_MPU_ATTR_DEVICE_GRE    (3U)
+
+/** \brief Memory Attribute
+* \param O Outer memory attributes
+* \param I O == ARM_MPU_ATTR_DEVICE: Device memory attributes, else: Inner memory attributes
+*/
+#define ARM_MPU_ATTR(O, I) (((O & 0xFU) << 4U) | (((O & 0xFU) != 0U) ? (I & 0xFU) : ((I & 0x3U) << 2U)))
+
+/** \brief Normal memory non-shareable  */
+#define ARM_MPU_SH_NON   (0U)
+
+/** \brief Normal memory outer shareable  */
+#define ARM_MPU_SH_OUTER (2U)
+
+/** \brief Normal memory inner shareable  */
+#define ARM_MPU_SH_INNER (3U)
+
+/** \brief Memory access permissions
+* \param RO Read-Only: Set to 1 for read-only memory.
+* \param NP Non-Privileged: Set to 1 for non-privileged memory.
+*/
+#define ARM_MPU_AP_(RO, NP) (((RO & 1U) << 1U) | (NP & 1U))
+
+/** \brief Region Base Address Register value
+* \param BASE The base address bits [31:5] of a memory region. The value is zero extended. Effective address gets 32 byte aligned.
+* \param SH Defines the Shareability domain for this memory region.
+* \param RO Read-Only: Set to 1 for a read-only memory region.
+* \param NP Non-Privileged: Set to 1 for a non-privileged memory region.
+* \oaram XN eXecute Never: Set to 1 for a non-executable memory region.
+*/
+#define ARM_MPU_RBAR(BASE, SH, RO, NP, XN) \
+  ((BASE & MPU_RBAR_BASE_Msk) | \
+  ((SH << MPU_RBAR_SH_Pos) & MPU_RBAR_SH_Msk) | \
+  ((ARM_MPU_AP_(RO, NP) << MPU_RBAR_AP_Pos) & MPU_RBAR_AP_Msk) | \
+  ((XN << MPU_RBAR_XN_Pos) & MPU_RBAR_XN_Msk))
+
+/** \brief Region Limit Address Register value
+* \param LIMIT The limit address bits [31:5] for this memory region. The value is one extended.
+* \param IDX The attribute index to be associated with this memory region.
+*/
+#define ARM_MPU_RLAR(LIMIT, IDX) \
+  ((LIMIT & MPU_RLAR_LIMIT_Msk) | \
+  ((IDX << MPU_RLAR_AttrIndx_Pos) & MPU_RLAR_AttrIndx_Msk) | \
+  (MPU_RLAR_EN_Msk))
+
+/**
+* Struct for a single MPU Region
+*/
+typedef struct {
+  uint32_t RBAR;                   /*!< Region Base Address Register value */
+  uint32_t RLAR;                   /*!< Region Limit Address Register value */
+} ARM_MPU_Region_t;
+    
+/** Enable the MPU.
+* \param MPU_Control Default access permissions for unconfigured regions.
+*/
+__STATIC_INLINE void ARM_MPU_Enable(uint32_t MPU_Control)
+{
+  __DSB();
+  __ISB();
+  MPU->CTRL = MPU_Control | MPU_CTRL_ENABLE_Msk;
+#ifdef SCB_SHCSR_MEMFAULTENA_Msk
+  SCB->SHCSR |= SCB_SHCSR_MEMFAULTENA_Msk;
+#endif
+}
+
+/** Disable the MPU.
+*/
+__STATIC_INLINE void ARM_MPU_Disable(void)
+{
+  __DSB();
+  __ISB();
+#ifdef SCB_SHCSR_MEMFAULTENA_Msk
+  SCB->SHCSR &= ~SCB_SHCSR_MEMFAULTENA_Msk;
+#endif
+  MPU->CTRL  &= ~MPU_CTRL_ENABLE_Msk;
+}
+
+#ifdef MPU_NS
+/** Enable the Non-secure MPU.
+* \param MPU_Control Default access permissions for unconfigured regions.
+*/
+__STATIC_INLINE void ARM_MPU_Enable_NS(uint32_t MPU_Control)
+{
+  __DSB();
+  __ISB();
+  MPU_NS->CTRL = MPU_Control | MPU_CTRL_ENABLE_Msk;
+#ifdef SCB_SHCSR_MEMFAULTENA_Msk
+  SCB_NS->SHCSR |= SCB_SHCSR_MEMFAULTENA_Msk;
+#endif
+}
+
+/** Disable the Non-secure MPU.
+*/
+__STATIC_INLINE void ARM_MPU_Disable_NS(void)
+{
+  __DSB();
+  __ISB();
+#ifdef SCB_SHCSR_MEMFAULTENA_Msk
+  SCB_NS->SHCSR &= ~SCB_SHCSR_MEMFAULTENA_Msk;
+#endif
+  MPU_NS->CTRL  &= ~MPU_CTRL_ENABLE_Msk;
+}
+#endif
+
+/** Set the memory attribute encoding to the given MPU.
+* \param mpu Pointer to the MPU to be configured.
+* \param idx The attribute index to be set [0-7]
+* \param attr The attribute value to be set.
+*/
+__STATIC_INLINE void ARM_MPU_SetMemAttrEx(MPU_Type* mpu, uint8_t idx, uint8_t attr)
+{
+  const uint8_t reg = idx / 4U;
+  const uint32_t pos = ((idx % 4U) * 8U);
+  const uint32_t mask = 0xFFU << pos;
+  
+  if (reg >= (sizeof(mpu->MAIR) / sizeof(mpu->MAIR[0]))) {
+    return; // invalid index
+  }
+  
+  mpu->MAIR[reg] = ((mpu->MAIR[reg] & ~mask) | ((attr << pos) & mask));
+}
+
+/** Set the memory attribute encoding.
+* \param idx The attribute index to be set [0-7]
+* \param attr The attribute value to be set.
+*/
+__STATIC_INLINE void ARM_MPU_SetMemAttr(uint8_t idx, uint8_t attr)
+{
+  ARM_MPU_SetMemAttrEx(MPU, idx, attr);
+}
+
+#ifdef MPU_NS
+/** Set the memory attribute encoding to the Non-secure MPU.
+* \param idx The attribute index to be set [0-7]
+* \param attr The attribute value to be set.
+*/
+__STATIC_INLINE void ARM_MPU_SetMemAttr_NS(uint8_t idx, uint8_t attr)
+{
+  ARM_MPU_SetMemAttrEx(MPU_NS, idx, attr);
+}
+#endif
+
+/** Clear and disable the given MPU region of the given MPU.
+* \param mpu Pointer to MPU to be used.
+* \param rnr Region number to be cleared.
+*/
+__STATIC_INLINE void ARM_MPU_ClrRegionEx(MPU_Type* mpu, uint32_t rnr)
+{
+  mpu->RNR = rnr;
+  mpu->RLAR = 0U;
+}
+
+/** Clear and disable the given MPU region.
+* \param rnr Region number to be cleared.
+*/
+__STATIC_INLINE void ARM_MPU_ClrRegion(uint32_t rnr)
+{
+  ARM_MPU_ClrRegionEx(MPU, rnr);
+}
+
+#ifdef MPU_NS
+/** Clear and disable the given Non-secure MPU region.
+* \param rnr Region number to be cleared.
+*/
+__STATIC_INLINE void ARM_MPU_ClrRegion_NS(uint32_t rnr)
+{  
+  ARM_MPU_ClrRegionEx(MPU_NS, rnr);
+}
+#endif
+
+/** Configure the given MPU region of the given MPU.
+* \param mpu Pointer to MPU to be used.
+* \param rnr Region number to be configured.
+* \param rbar Value for RBAR register.
+* \param rlar Value for RLAR register.
+*/   
+__STATIC_INLINE void ARM_MPU_SetRegionEx(MPU_Type* mpu, uint32_t rnr, uint32_t rbar, uint32_t rlar)
+{
+  mpu->RNR = rnr;
+  mpu->RBAR = rbar;
+  mpu->RLAR = rlar;
+}
+
+/** Configure the given MPU region.
+* \param rnr Region number to be configured.
+* \param rbar Value for RBAR register.
+* \param rlar Value for RLAR register.
+*/   
+__STATIC_INLINE void ARM_MPU_SetRegion(uint32_t rnr, uint32_t rbar, uint32_t rlar)
+{
+  ARM_MPU_SetRegionEx(MPU, rnr, rbar, rlar);
+}
+
+#ifdef MPU_NS
+/** Configure the given Non-secure MPU region.
+* \param rnr Region number to be configured.
+* \param rbar Value for RBAR register.
+* \param rlar Value for RLAR register.
+*/   
+__STATIC_INLINE void ARM_MPU_SetRegion_NS(uint32_t rnr, uint32_t rbar, uint32_t rlar)
+{
+  ARM_MPU_SetRegionEx(MPU_NS, rnr, rbar, rlar);  
+}
+#endif
+
+/** Memcopy with strictly ordered memory access, e.g. for register targets.
+* \param dst Destination data is copied to.
+* \param src Source data is copied from.
+* \param len Amount of data words to be copied.
+*/
+__STATIC_INLINE void orderedCpy(volatile uint32_t* dst, const uint32_t* __RESTRICT src, uint32_t len)
+{
+  uint32_t i;
+  for (i = 0U; i < len; ++i) 
+  {
+    dst[i] = src[i];
+  }
+}
+
+/** Load the given number of MPU regions from a table to the given MPU.
+* \param mpu Pointer to the MPU registers to be used.
+* \param rnr First region number to be configured.
+* \param table Pointer to the MPU configuration table.
+* \param cnt Amount of regions to be configured.
+*/
+__STATIC_INLINE void ARM_MPU_LoadEx(MPU_Type* mpu, uint32_t rnr, ARM_MPU_Region_t const* table, uint32_t cnt) 
+{
+  const uint32_t rowWordSize = sizeof(ARM_MPU_Region_t)/4U;
+  if (cnt == 1U) {
+    mpu->RNR = rnr;
+    orderedCpy(&(mpu->RBAR), &(table->RBAR), rowWordSize);
+  } else {
+    uint32_t rnrBase   = rnr & ~(MPU_TYPE_RALIASES-1U);
+    uint32_t rnrOffset = rnr % MPU_TYPE_RALIASES;
+    
+    mpu->RNR = rnrBase;
+    while ((rnrOffset + cnt) > MPU_TYPE_RALIASES) {
+      uint32_t c = MPU_TYPE_RALIASES - rnrOffset;
+      orderedCpy(&(mpu->RBAR)+(rnrOffset*2U), &(table->RBAR), c*rowWordSize);
+      table += c;
+      cnt -= c;
+      rnrOffset = 0U;
+      rnrBase += MPU_TYPE_RALIASES;
+      mpu->RNR = rnrBase;
+    }
+    
+    orderedCpy(&(mpu->RBAR)+(rnrOffset*2U), &(table->RBAR), cnt*rowWordSize);
+  }
+}
+
+/** Load the given number of MPU regions from a table.
+* \param rnr First region number to be configured.
+* \param table Pointer to the MPU configuration table.
+* \param cnt Amount of regions to be configured.
+*/
+__STATIC_INLINE void ARM_MPU_Load(uint32_t rnr, ARM_MPU_Region_t const* table, uint32_t cnt) 
+{
+  ARM_MPU_LoadEx(MPU, rnr, table, cnt);
+}
+
+#ifdef MPU_NS
+/** Load the given number of MPU regions from a table to the Non-secure MPU.
+* \param rnr First region number to be configured.
+* \param table Pointer to the MPU configuration table.
+* \param cnt Amount of regions to be configured.
+*/
+__STATIC_INLINE void ARM_MPU_Load_NS(uint32_t rnr, ARM_MPU_Region_t const* table, uint32_t cnt) 
+{
+  ARM_MPU_LoadEx(MPU_NS, rnr, table, cnt);
+}
+#endif
+
+#endif
+

Drivers/CMSIS/Include/tz_context.h

@@ -0,0 +1,70 @@
+/******************************************************************************
+ * @file     tz_context.h
+ * @brief    Context Management for Armv8-M TrustZone
+ * @version  V1.0.1
+ * @date     10. January 2018
+ ******************************************************************************/
+/*
+ * Copyright (c) 2017-2018 Arm Limited. All rights reserved.
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Licensed under the Apache License, Version 2.0 (the License); you may
+ * not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an AS IS BASIS, WITHOUT
+ * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ */
+
+#if   defined ( __ICCARM__ )
+  #pragma system_include         /* treat file as system include file for MISRA check */
+#elif defined (__clang__)
+  #pragma clang system_header   /* treat file as system include file */
+#endif
+
+#ifndef TZ_CONTEXT_H
+#define TZ_CONTEXT_H
+ 
+#include <stdint.h>
+ 
+#ifndef TZ_MODULEID_T
+#define TZ_MODULEID_T
+/// \details Data type that identifies secure software modules called by a process.
+typedef uint32_t TZ_ModuleId_t;
+#endif
+ 
+/// \details TZ Memory ID identifies an allocated memory slot.
+typedef uint32_t TZ_MemoryId_t;
+  
+/// Initialize secure context memory system
+/// \return execution status (1: success, 0: error)
+uint32_t TZ_InitContextSystem_S (void);
+ 
+/// Allocate context memory for calling secure software modules in TrustZone
+/// \param[in]  module   identifies software modules called from non-secure mode
+/// \return value != 0 id TrustZone memory slot identifier
+/// \return value 0    no memory available or internal error
+TZ_MemoryId_t TZ_AllocModuleContext_S (TZ_ModuleId_t module);
+ 
+/// Free context memory that was previously allocated with \ref TZ_AllocModuleContext_S
+/// \param[in]  id  TrustZone memory slot identifier
+/// \return execution status (1: success, 0: error)
+uint32_t TZ_FreeModuleContext_S (TZ_MemoryId_t id);
+ 
+/// Load secure context (called on RTOS thread context switch)
+/// \param[in]  id  TrustZone memory slot identifier
+/// \return execution status (1: success, 0: error)
+uint32_t TZ_LoadContext_S (TZ_MemoryId_t id);
+ 
+/// Store secure context (called on RTOS thread context switch)
+/// \param[in]  id  TrustZone memory slot identifier
+/// \return execution status (1: success, 0: error)
+uint32_t TZ_StoreContext_S (TZ_MemoryId_t id);
+ 
+#endif  // TZ_CONTEXT_H

Drivers/STM32F1xx_HAL_Driver/Inc/Legacy/stm32f1xx_hal_can_ex_legacy.h

@@ -0,0 +1,128 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_hal_can_ex_legacy.h
+  * @author  MCD Application Team
+  * @brief   Header file of CAN HAL Extension module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */ 
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F1xx_HAL_CAN_EX_LEGACY_H
+#define __STM32F1xx_HAL_CAN_EX_LEGACY_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+#if defined(STM32F103x6) || defined(STM32F103xB) || defined(STM32F103xE) || \
+    defined(STM32F103xG) || defined(STM32F105xC) || defined(STM32F107xC)
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_hal_def.h"
+
+/** @addtogroup STM32F1xx_HAL_Driver
+  * @{
+  */
+
+/** @defgroup CANEx CANEx
+  * @{
+  */ 
+
+/* Exported types ------------------------------------------------------------*/
+
+/** 
+  * @brief  CAN filter configuration structure definition
+  */
+/* CAN filter banks differences over STM32F1 devices:                         */
+/* - STM32F1 Connectivity line: 28 filter banks shared between CAN1 and CAN2  */
+/* - Other STM32F10x devices:   14 filter banks                               */
+
+typedef struct
+{
+  uint32_t FilterIdHigh;          /*!< Specifies the filter identification number (MSBs for a 32-bit
+                                       configuration, first one for a 16-bit configuration).
+                                       This parameter must be a number between Min_Data = 0x0000 and Max_Data = 0xFFFF. */ 
+                                              
+  uint32_t FilterIdLow;           /*!< Specifies the filter identification number (LSBs for a 32-bit
+                                       configuration, second one for a 16-bit configuration).
+                                       This parameter must be a number between Min_Data = 0x0000 and Max_Data = 0xFFFF. */ 
+
+  uint32_t FilterMaskIdHigh;      /*!< Specifies the filter mask number or identification number,
+                                       according to the mode (MSBs for a 32-bit configuration,
+                                       first one for a 16-bit configuration).
+                                       This parameter must be a number between Min_Data = 0x0000 and Max_Data = 0xFFFF. */ 
+
+  uint32_t FilterMaskIdLow;       /*!< Specifies the filter mask number or identification number,
+                                       according to the mode (LSBs for a 32-bit configuration,
+                                       second one for a 16-bit configuration).
+                                       This parameter must be a number between Min_Data = 0x0000 and Max_Data = 0xFFFF. */ 
+
+  uint32_t FilterFIFOAssignment;  /*!< Specifies the FIFO (0 or 1) which will be assigned to the filter.
+                                       This parameter can be a value of @ref CAN_filter_FIFO */
+#if defined(STM32F105xC) || defined(STM32F107xC)
+  uint32_t FilterNumber;          /*!< Specifies the filter which will be initialized. 
+                                       This parameter must be a number between Min_Data = 0 and Max_Data = 27. */
+#else
+  uint32_t FilterNumber;          /*!< Specifies the filter which will be initialized. 
+                                       This parameter must be a number between Min_Data = 0 and Max_Data = 13. */
+#endif /* STM32F105xC || STM32F107xC */
+  uint32_t FilterMode;            /*!< Specifies the filter mode to be initialized.
+                                       This parameter can be a value of @ref CAN_filter_mode */
+
+  uint32_t FilterScale;           /*!< Specifies the filter scale.
+                                       This parameter can be a value of @ref CAN_filter_scale */
+
+  uint32_t FilterActivation;      /*!< Enable or disable the filter.
+                                       This parameter can be set to ENABLE or DISABLE. */
+                                       
+  uint32_t BankNumber;            /*!< Select the start slave bank filter
+                                       This parameter must be a number between Min_Data = 0 and Max_Data = 28. */ 
+  
+}CAN_FilterConfTypeDef;
+
+/* Exported constants --------------------------------------------------------*/
+/* Exported macro ------------------------------------------------------------*/
+/* Private macro -------------------------------------------------------------*/
+
+/** @defgroup CANEx_Private_Macros CAN Extended Private Macros
+  * @{
+  */
+#if defined(STM32F105xC) || defined(STM32F107xC)
+#define IS_CAN_FILTER_NUMBER(NUMBER) ((NUMBER) <= 27U)
+#else
+#define IS_CAN_FILTER_NUMBER(NUMBER) ((NUMBER) <= 13U)
+#endif /* STM32F105xC || STM32F107xC */
+
+/**
+  * @}
+  */
+
+
+/**
+  * @}
+  */ 
+
+/**
+  * @}
+  */
+
+#endif /* STM32F103x6) || STM32F103xB || STM32F103xE || STM32F103xG) || STM32F105xC || STM32F107xC    */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F1xx_HAL_CAN_EX_LEGACY_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/STM32F1xx_HAL_Driver/Inc/Legacy/stm32f1xx_hal_can_legacy.h

@@ -0,0 +1,796 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_hal_can_legacy.h
+  * @author  MCD Application Team
+  * @brief   Header file of CAN HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; COPYRIGHT(c) 2017 STMicroelectronics</center></h2>
+  *
+  * Redistribution and use in source and binary forms, with or without modification,
+  * are permitted provided that the following conditions are met:
+  *   1. Redistributions of source code must retain the above copyright notice,
+  *      this list of conditions and the following disclaimer.
+  *   2. Redistributions in binary form must reproduce the above copyright notice,
+  *      this list of conditions and the following disclaimer in the documentation
+  *      and/or other materials provided with the distribution.
+  *   3. Neither the name of STMicroelectronics nor the names of its contributors
+  *      may be used to endorse or promote products derived from this software
+  *      without specific prior written permission.
+  *
+  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+  * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+  * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+  * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+  * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F1xx_HAL_CAN_LEGACY_H
+#define __STM32F1xx_HAL_CAN_LEGACY_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+     
+#if defined(STM32F103x6) || defined(STM32F103xB) || defined(STM32F103xE) || \
+    defined(STM32F103xG) || defined(STM32F105xC) || defined(STM32F107xC)
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_hal_def.h"
+
+/** @addtogroup STM32F1xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup CAN
+  * @{
+  */
+
+/* Exported types ------------------------------------------------------------*/
+/** @defgroup CAN_Exported_Types CAN Exported Types
+  * @{
+  */
+
+/**
+  * @brief  HAL State structures definition
+  */
+typedef enum
+{
+  HAL_CAN_STATE_RESET             = 0x00U,  /*!< CAN not yet initialized or disabled */
+  HAL_CAN_STATE_READY             = 0x01U,  /*!< CAN initialized and ready for use   */
+  HAL_CAN_STATE_BUSY              = 0x02U,  /*!< CAN process is ongoing              */
+  HAL_CAN_STATE_BUSY_TX           = 0x12U,  /*!< CAN process is ongoing              */
+  HAL_CAN_STATE_BUSY_RX0          = 0x22U,  /*!< CAN process is ongoing              */
+  HAL_CAN_STATE_BUSY_RX1          = 0x32U,  /*!< CAN process is ongoing              */
+  HAL_CAN_STATE_BUSY_TX_RX0       = 0x42U,  /*!< CAN process is ongoing              */
+  HAL_CAN_STATE_BUSY_TX_RX1       = 0x52U,  /*!< CAN process is ongoing              */
+  HAL_CAN_STATE_BUSY_RX0_RX1      = 0x62U,  /*!< CAN process is ongoing              */
+  HAL_CAN_STATE_BUSY_TX_RX0_RX1   = 0x72U,  /*!< CAN process is ongoing              */
+  HAL_CAN_STATE_TIMEOUT           = 0x03U,  /*!< CAN in Timeout state                */
+  HAL_CAN_STATE_ERROR             = 0x04U   /*!< CAN error state                     */
+
+}HAL_CAN_StateTypeDef;
+
+/**
+  * @brief  CAN init structure definition
+  */
+typedef struct
+{
+  uint32_t Prescaler;  /*!< Specifies the length of a time quantum.
+                            This parameter must be a number between Min_Data = 1 and Max_Data = 1024 */
+
+  uint32_t Mode;       /*!< Specifies the CAN operating mode.
+                            This parameter can be a value of @ref CAN_operating_mode */
+
+  uint32_t SJW;        /*!< Specifies the maximum number of time quanta
+                            the CAN hardware is allowed to lengthen or
+                            shorten a bit to perform resynchronization.
+                            This parameter can be a value of @ref CAN_synchronisation_jump_width */
+
+  uint32_t BS1;        /*!< Specifies the number of time quanta in Bit Segment 1.
+                            This parameter can be a value of @ref CAN_time_quantum_in_bit_segment_1 */
+
+  uint32_t BS2;        /*!< Specifies the number of time quanta in Bit Segment 2.
+                            This parameter can be a value of @ref CAN_time_quantum_in_bit_segment_2 */
+
+  uint32_t TTCM;       /*!< Enable or disable the time triggered communication mode.
+                            This parameter can be set to ENABLE or DISABLE. */
+
+  uint32_t ABOM;       /*!< Enable or disable the automatic bus-off management.
+                            This parameter can be set to ENABLE or DISABLE */
+
+  uint32_t AWUM;       /*!< Enable or disable the automatic wake-up mode.
+                            This parameter can be set to ENABLE or DISABLE */
+
+  uint32_t NART;       /*!< Enable or disable the non-automatic retransmission mode.
+                            This parameter can be set to ENABLE or DISABLE */
+
+  uint32_t RFLM;       /*!< Enable or disable the receive FIFO Locked mode.
+                            This parameter can be set to ENABLE or DISABLE */
+
+  uint32_t TXFP;       /*!< Enable or disable the transmit FIFO priority.
+                            This parameter can be set to ENABLE or DISABLE */
+}CAN_InitTypeDef;
+
+/** 
+  * @brief  CAN Tx message structure definition  
+  */
+typedef struct
+{
+  uint32_t StdId;    /*!< Specifies the standard identifier.
+                          This parameter must be a number between Min_Data = 0 and Max_Data = 0x7FF */
+
+  uint32_t ExtId;    /*!< Specifies the extended identifier.
+                          This parameter must be a number between Min_Data = 0 and Max_Data = 0x1FFFFFFF */
+
+  uint32_t IDE;      /*!< Specifies the type of identifier for the message that will be transmitted.
+                          This parameter can be a value of @ref CAN_Identifier_Type */
+
+  uint32_t RTR;      /*!< Specifies the type of frame for the message that will be transmitted.
+                          This parameter can be a value of @ref CAN_remote_transmission_request */
+
+  uint32_t DLC;      /*!< Specifies the length of the frame that will be transmitted.
+                          This parameter must be a number between Min_Data = 0 and Max_Data = 8 */
+
+  uint8_t Data[8];   /*!< Contains the data to be transmitted.
+                          This parameter must be a number between Min_Data = 0 and Max_Data = 0xFF */
+
+}CanTxMsgTypeDef;
+
+/**
+  * @brief  CAN Rx message structure definition
+  */
+typedef struct
+{
+  uint32_t StdId;       /*!< Specifies the standard identifier.
+                             This parameter must be a number between Min_Data = 0 and Max_Data = 0x7FF */
+
+  uint32_t ExtId;       /*!< Specifies the extended identifier.
+                             This parameter must be a number between Min_Data = 0 and Max_Data = 0x1FFFFFFF */
+
+  uint32_t IDE;         /*!< Specifies the type of identifier for the message that will be received.
+                             This parameter can be a value of @ref CAN_Identifier_Type */
+
+  uint32_t RTR;         /*!< Specifies the type of frame for the received message.
+                             This parameter can be a value of @ref CAN_remote_transmission_request */
+
+  uint32_t DLC;         /*!< Specifies the length of the frame that will be received.
+                             This parameter must be a number between Min_Data = 0 and Max_Data = 8 */
+
+  uint8_t Data[8];      /*!< Contains the data to be received.
+                             This parameter must be a number between Min_Data = 0 and Max_Data = 0xFF */
+
+  uint32_t FMI;         /*!< Specifies the index of the filter the message stored in the mailbox passes through.
+                             This parameter must be a number between Min_Data = 0 and Max_Data = 0xFF */
+
+  uint32_t FIFONumber;  /*!< Specifies the receive FIFO number.
+                             This parameter can be CAN_FIFO0 or CAN_FIFO1 */
+
+}CanRxMsgTypeDef;
+
+/**
+  * @brief  CAN handle Structure definition
+  */
+typedef struct
+{
+  CAN_TypeDef                 *Instance;  /*!< Register base address          */
+
+  CAN_InitTypeDef             Init;       /*!< CAN required parameters        */
+
+  CanTxMsgTypeDef*            pTxMsg;     /*!< Pointer to transmit structure  */
+
+  CanRxMsgTypeDef*            pRxMsg;     /*!< Pointer to reception structure for RX FIFO0 msg */
+
+  CanRxMsgTypeDef*            pRx1Msg;    /*!< Pointer to reception structure for RX FIFO1 msg */
+
+  __IO HAL_CAN_StateTypeDef   State;      /*!< CAN communication state        */
+
+  HAL_LockTypeDef             Lock;       /*!< CAN locking object             */
+
+  __IO uint32_t               ErrorCode;  /*!< CAN Error code                 */
+
+}CAN_HandleTypeDef;
+
+/**
+  * @}
+  */
+
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup CAN_Exported_Constants CAN Exported Constants
+  * @{
+  */
+
+/** @defgroup CAN_Error_Code CAN Error Code
+  * @{
+  */
+#define   HAL_CAN_ERROR_NONE      0x00000000U    /*!< No error             */
+#define   HAL_CAN_ERROR_EWG       0x00000001U    /*!< EWG error            */
+#define   HAL_CAN_ERROR_EPV       0x00000002U    /*!< EPV error            */
+#define   HAL_CAN_ERROR_BOF       0x00000004U    /*!< BOF error            */
+#define   HAL_CAN_ERROR_STF       0x00000008U    /*!< Stuff error          */
+#define   HAL_CAN_ERROR_FOR       0x00000010U    /*!< Form error           */
+#define   HAL_CAN_ERROR_ACK       0x00000020U    /*!< Acknowledgment error */
+#define   HAL_CAN_ERROR_BR        0x00000040U    /*!< Bit recessive        */
+#define   HAL_CAN_ERROR_BD        0x00000080U    /*!< LEC dominant         */
+#define   HAL_CAN_ERROR_CRC       0x00000100U    /*!< LEC transfer error   */
+#define   HAL_CAN_ERROR_FOV0      0x00000200U    /*!< FIFO0 overrun error  */
+#define   HAL_CAN_ERROR_FOV1      0x00000400U    /*!< FIFO1 overrun error  */
+#define   HAL_CAN_ERROR_TXFAIL    0x00000800U    /*!< Transmit failure     */
+/**
+  * @}
+  */
+
+/** @defgroup CAN_InitStatus CAN initialization Status
+  * @{
+  */
+#define CAN_INITSTATUS_FAILED       0x00000000U  /*!< CAN initialization failed */
+#define CAN_INITSTATUS_SUCCESS      0x00000001U  /*!< CAN initialization OK */
+/**
+  * @}
+  */
+
+/** @defgroup CAN_operating_mode CAN Operating Mode
+  * @{
+  */
+#define CAN_MODE_NORMAL             0x00000000U                                /*!< Normal mode   */
+#define CAN_MODE_LOOPBACK           ((uint32_t)CAN_BTR_LBKM)                   /*!< Loopback mode */
+#define CAN_MODE_SILENT             ((uint32_t)CAN_BTR_SILM)                   /*!< Silent mode   */
+#define CAN_MODE_SILENT_LOOPBACK    ((uint32_t)(CAN_BTR_LBKM | CAN_BTR_SILM))  /*!< Loopback combined with silent mode */
+/**
+  * @}
+  */
+
+/** @defgroup CAN_synchronisation_jump_width CAN Synchronization Jump Width
+  * @{
+  */
+#define CAN_SJW_1TQ                 0x00000000U                /*!< 1 time quantum */
+#define CAN_SJW_2TQ                 ((uint32_t)CAN_BTR_SJW_0)  /*!< 2 time quantum */
+#define CAN_SJW_3TQ                 ((uint32_t)CAN_BTR_SJW_1)  /*!< 3 time quantum */
+#define CAN_SJW_4TQ                 ((uint32_t)CAN_BTR_SJW)    /*!< 4 time quantum */
+/**
+  * @}
+  */
+
+/** @defgroup CAN_time_quantum_in_bit_segment_1 CAN Time Quantum in Bit Segment 1
+  * @{
+  */
+#define CAN_BS1_1TQ                 0x00000000U                                                  /*!< 1 time quantum  */
+#define CAN_BS1_2TQ                 ((uint32_t)CAN_BTR_TS1_0)                                    /*!< 2 time quantum  */
+#define CAN_BS1_3TQ                 ((uint32_t)CAN_BTR_TS1_1)                                    /*!< 3 time quantum  */
+#define CAN_BS1_4TQ                 ((uint32_t)(CAN_BTR_TS1_1 | CAN_BTR_TS1_0))                  /*!< 4 time quantum  */
+#define CAN_BS1_5TQ                 ((uint32_t)CAN_BTR_TS1_2)                                    /*!< 5 time quantum  */
+#define CAN_BS1_6TQ                 ((uint32_t)(CAN_BTR_TS1_2 | CAN_BTR_TS1_0))                  /*!< 6 time quantum  */
+#define CAN_BS1_7TQ                 ((uint32_t)(CAN_BTR_TS1_2 | CAN_BTR_TS1_1))                  /*!< 7 time quantum  */
+#define CAN_BS1_8TQ                 ((uint32_t)(CAN_BTR_TS1_2 | CAN_BTR_TS1_1 | CAN_BTR_TS1_0))  /*!< 8 time quantum  */
+#define CAN_BS1_9TQ                 ((uint32_t)CAN_BTR_TS1_3)                                    /*!< 9 time quantum  */
+#define CAN_BS1_10TQ                ((uint32_t)(CAN_BTR_TS1_3 | CAN_BTR_TS1_0))                  /*!< 10 time quantum */
+#define CAN_BS1_11TQ                ((uint32_t)(CAN_BTR_TS1_3 | CAN_BTR_TS1_1))                  /*!< 11 time quantum */
+#define CAN_BS1_12TQ                ((uint32_t)(CAN_BTR_TS1_3 | CAN_BTR_TS1_1 | CAN_BTR_TS1_0))  /*!< 12 time quantum */
+#define CAN_BS1_13TQ                ((uint32_t)(CAN_BTR_TS1_3 | CAN_BTR_TS1_2))                  /*!< 13 time quantum */
+#define CAN_BS1_14TQ                ((uint32_t)(CAN_BTR_TS1_3 | CAN_BTR_TS1_2 | CAN_BTR_TS1_0))  /*!< 14 time quantum */
+#define CAN_BS1_15TQ                ((uint32_t)(CAN_BTR_TS1_3 | CAN_BTR_TS1_2 | CAN_BTR_TS1_1))  /*!< 15 time quantum */
+#define CAN_BS1_16TQ                ((uint32_t)CAN_BTR_TS1) /*!< 16 time quantum */
+/**
+  * @}
+  */
+
+/** @defgroup CAN_time_quantum_in_bit_segment_2 CAN Time Quantum in bit segment 2
+  * @{
+  */
+#define CAN_BS2_1TQ                 0x00000000U                                  /*!< 1 time quantum */
+#define CAN_BS2_2TQ                 ((uint32_t)CAN_BTR_TS2_0)                    /*!< 2 time quantum */
+#define CAN_BS2_3TQ                 ((uint32_t)CAN_BTR_TS2_1)                    /*!< 3 time quantum */
+#define CAN_BS2_4TQ                 ((uint32_t)(CAN_BTR_TS2_1 | CAN_BTR_TS2_0))  /*!< 4 time quantum */
+#define CAN_BS2_5TQ                 ((uint32_t)CAN_BTR_TS2_2)                    /*!< 5 time quantum */
+#define CAN_BS2_6TQ                 ((uint32_t)(CAN_BTR_TS2_2 | CAN_BTR_TS2_0))  /*!< 6 time quantum */
+#define CAN_BS2_7TQ                 ((uint32_t)(CAN_BTR_TS2_2 | CAN_BTR_TS2_1))  /*!< 7 time quantum */
+#define CAN_BS2_8TQ                 ((uint32_t)CAN_BTR_TS2)                      /*!< 8 time quantum */
+/**
+  * @}
+  */
+
+/** @defgroup CAN_filter_mode  CAN Filter Mode
+  * @{
+  */
+#define CAN_FILTERMODE_IDMASK       ((uint8_t)0x00)  /*!< Identifier mask mode */
+#define CAN_FILTERMODE_IDLIST       ((uint8_t)0x01)  /*!< Identifier list mode */
+/**
+  * @}
+  */
+
+/** @defgroup CAN_filter_scale CAN Filter Scale
+  * @{
+  */
+#define CAN_FILTERSCALE_16BIT       ((uint8_t)0x00)  /*!< Two 16-bit filters */
+#define CAN_FILTERSCALE_32BIT       ((uint8_t)0x01)  /*!< One 32-bit filter  */
+/**
+  * @}
+  */
+
+/** @defgroup CAN_filter_FIFO CAN Filter FIFO
+  * @{
+  */
+#define CAN_FILTER_FIFO0             ((uint8_t)0x00)  /*!< Filter FIFO 0 assignment for filter x */
+#define CAN_FILTER_FIFO1             ((uint8_t)0x01)  /*!< Filter FIFO 1 assignment for filter x */
+/**
+  * @}
+  */
+
+/** @defgroup CAN_Identifier_Type CAN Identifier Type
+  * @{
+  */
+#define CAN_ID_STD                  0x00000000U  /*!< Standard Id */
+#define CAN_ID_EXT                  0x00000004U  /*!< Extended Id */
+/**
+  * @}
+  */
+
+/** @defgroup CAN_remote_transmission_request CAN Remote Transmission Request
+  * @{
+  */
+#define CAN_RTR_DATA                0x00000000U  /*!< Data frame */
+#define CAN_RTR_REMOTE              0x00000002U  /*!< Remote frame */
+/**
+  * @}
+  */
+
+/** @defgroup CAN_transmit_constants CAN Transmit Constants
+  * @{
+  */
+#define CAN_TXSTATUS_NOMAILBOX      ((uint8_t)0x04)  /*!< CAN cell did not provide CAN_TxStatus_NoMailBox */
+/**
+  * @}
+  */
+
+/** @defgroup CAN_receive_FIFO_number_constants CAN Receive FIFO Number
+  * @{
+  */
+#define CAN_FIFO0                   ((uint8_t)0x00)  /*!< CAN FIFO 0 used to receive */
+#define CAN_FIFO1                   ((uint8_t)0x01)  /*!< CAN FIFO 1 used to receive */
+/**
+  * @}
+  */
+
+/** @defgroup CAN_flags CAN Flags
+  * @{
+  */
+/* If the flag is 0x3XXXXXXX, it means that it can be used with CAN_GetFlagStatus()
+   and CAN_ClearFlag() functions. */
+/* If the flag is 0x1XXXXXXX, it means that it can only be used with
+   CAN_GetFlagStatus() function.  */
+
+/* Transmit Flags */
+#define CAN_FLAG_RQCP0             ((uint32_t)((TSR_REGISTER_INDEX << 8U) | CAN_TSR_RQCP0_BIT_POSITION))  /*!< Request MailBox0 flag         */
+#define CAN_FLAG_RQCP1             ((uint32_t)((TSR_REGISTER_INDEX << 8U) | CAN_TSR_RQCP1_BIT_POSITION))  /*!< Request MailBox1 flag         */
+#define CAN_FLAG_RQCP2             ((uint32_t)((TSR_REGISTER_INDEX << 8U) | CAN_TSR_RQCP2_BIT_POSITION))  /*!< Request MailBox2 flag         */
+#define CAN_FLAG_TXOK0             ((uint32_t)((TSR_REGISTER_INDEX << 8U) | CAN_TSR_TXOK0_BIT_POSITION))  /*!< Transmission OK MailBox0 flag */
+#define CAN_FLAG_TXOK1             ((uint32_t)((TSR_REGISTER_INDEX << 8U) | CAN_TSR_TXOK1_BIT_POSITION))  /*!< Transmission OK MailBox1 flag */
+#define CAN_FLAG_TXOK2             ((uint32_t)((TSR_REGISTER_INDEX << 8U) | CAN_TSR_TXOK2_BIT_POSITION))  /*!< Transmission OK MailBox2 flag */
+#define CAN_FLAG_TME0              ((uint32_t)((TSR_REGISTER_INDEX << 8U) | CAN_TSR_TME0_BIT_POSITION))   /*!< Transmit mailbox 0 empty flag */
+#define CAN_FLAG_TME1              ((uint32_t)((TSR_REGISTER_INDEX << 8U) | CAN_TSR_TME1_BIT_POSITION))   /*!< Transmit mailbox 0 empty flag */
+#define CAN_FLAG_TME2              ((uint32_t)((TSR_REGISTER_INDEX << 8U) | CAN_TSR_TME2_BIT_POSITION))   /*!< Transmit mailbox 0 empty flag */
+
+/* Receive Flags */
+#define CAN_FLAG_FF0               ((uint32_t)((RF0R_REGISTER_INDEX << 8U) | CAN_RF0R_FF0_BIT_POSITION))  /*!< FIFO 0 Full flag    */
+#define CAN_FLAG_FOV0              ((uint32_t)((RF0R_REGISTER_INDEX << 8U) | CAN_RF0R_FOV0_BIT_POSITION)) /*!< FIFO 0 Overrun flag */
+
+#define CAN_FLAG_FF1               ((uint32_t)((RF1R_REGISTER_INDEX << 8U) | CAN_RF1R_FF1_BIT_POSITION))  /*!< FIFO 1 Full flag    */
+#define CAN_FLAG_FOV1              ((uint32_t)((RF1R_REGISTER_INDEX << 8U) | CAN_RF1R_FOV1_BIT_POSITION)) /*!< FIFO 1 Overrun flag */
+
+/* Operating Mode Flags */
+#define CAN_FLAG_WKU               ((uint32_t)((MSR_REGISTER_INDEX << 8U) | CAN_MSR_WKU_BIT_POSITION))    /*!< Wake up flag           */
+#define CAN_FLAG_SLAK              ((uint32_t)((MSR_REGISTER_INDEX << 8U) | CAN_MSR_SLAK_BIT_POSITION))   /*!< Sleep acknowledge flag */
+#define CAN_FLAG_SLAKI             ((uint32_t)((MSR_REGISTER_INDEX << 8U) | CAN_MSR_SLAKI_BIT_POSITION))  /*!< Sleep acknowledge flag */
+
+/* @note When SLAK interrupt is disabled (SLKIE=0), no polling on SLAKI is possible. 
+         In this case the SLAK bit can be polled.*/
+
+/* Error Flags */
+#define CAN_FLAG_EWG               ((uint32_t)((ESR_REGISTER_INDEX << 8U) | CAN_ESR_EWG_BIT_POSITION))    /*!< Error warning flag   */
+#define CAN_FLAG_EPV               ((uint32_t)((ESR_REGISTER_INDEX << 8U) | CAN_ESR_EPV_BIT_POSITION))    /*!< Error passive flag   */
+#define CAN_FLAG_BOF               ((uint32_t)((ESR_REGISTER_INDEX << 8U) | CAN_ESR_BOF_BIT_POSITION))    /*!< Bus-Off flag         */
+
+/**
+  * @}
+  */
+
+/** @defgroup CAN_Interrupts CAN Interrupts
+  * @{
+  */
+#define CAN_IT_TME                  ((uint32_t)CAN_IER_TMEIE)   /*!< Transmit mailbox empty interrupt */
+
+/* Receive Interrupts */
+#define CAN_IT_FMP0                 ((uint32_t)CAN_IER_FMPIE0)  /*!< FIFO 0 message pending interrupt */
+#define CAN_IT_FF0                  ((uint32_t)CAN_IER_FFIE0)   /*!< FIFO 0 full interrupt            */
+#define CAN_IT_FOV0                 ((uint32_t)CAN_IER_FOVIE0)  /*!< FIFO 0 overrun interrupt         */
+#define CAN_IT_FMP1                 ((uint32_t)CAN_IER_FMPIE1)  /*!< FIFO 1 message pending interrupt */
+#define CAN_IT_FF1                  ((uint32_t)CAN_IER_FFIE1)   /*!< FIFO 1 full interrupt            */
+#define CAN_IT_FOV1                 ((uint32_t)CAN_IER_FOVIE1)  /*!< FIFO 1 overrun interrupt         */
+
+/* Operating Mode Interrupts */
+#define CAN_IT_WKU                  ((uint32_t)CAN_IER_WKUIE)  /*!< Wake-up interrupt           */
+#define CAN_IT_SLK                  ((uint32_t)CAN_IER_SLKIE)  /*!< Sleep acknowledge interrupt */
+
+/* Error Interrupts */
+#define CAN_IT_EWG                  ((uint32_t)CAN_IER_EWGIE) /*!< Error warning interrupt   */
+#define CAN_IT_EPV                  ((uint32_t)CAN_IER_EPVIE) /*!< Error passive interrupt   */
+#define CAN_IT_BOF                  ((uint32_t)CAN_IER_BOFIE) /*!< Bus-off interrupt         */
+#define CAN_IT_LEC                  ((uint32_t)CAN_IER_LECIE) /*!< Last error code interrupt */
+#define CAN_IT_ERR                  ((uint32_t)CAN_IER_ERRIE) /*!< Error Interrupt           */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup CAN_Private_Constants CAN Private Constants
+  * @{
+  */
+
+/* CAN intermediate shift values used for CAN flags */
+#define TSR_REGISTER_INDEX      0x5U
+#define RF0R_REGISTER_INDEX     0x2U
+#define RF1R_REGISTER_INDEX     0x4U
+#define MSR_REGISTER_INDEX      0x1U
+#define ESR_REGISTER_INDEX      0x3U
+
+/* CAN flags bits position into their respective register (TSR, RF0R, RF1R or MSR regsiters) */
+/* Transmit Flags */
+#define CAN_TSR_RQCP0_BIT_POSITION     0x00000000U
+#define CAN_TSR_RQCP1_BIT_POSITION     0x00000008U
+#define CAN_TSR_RQCP2_BIT_POSITION     0x00000010U
+#define CAN_TSR_TXOK0_BIT_POSITION     0x00000001U
+#define CAN_TSR_TXOK1_BIT_POSITION     0x00000009U
+#define CAN_TSR_TXOK2_BIT_POSITION     0x00000011U
+#define CAN_TSR_TME0_BIT_POSITION      0x0000001AU
+#define CAN_TSR_TME1_BIT_POSITION      0x0000001BU
+#define CAN_TSR_TME2_BIT_POSITION      0x0000001CU
+
+/* Receive Flags */
+#define CAN_RF0R_FF0_BIT_POSITION      0x00000003U
+#define CAN_RF0R_FOV0_BIT_POSITION     0x00000004U
+
+#define CAN_RF1R_FF1_BIT_POSITION      0x00000003U
+#define CAN_RF1R_FOV1_BIT_POSITION     0x00000004U
+
+/* Operating Mode Flags */
+#define CAN_MSR_WKU_BIT_POSITION       0x00000003U
+#define CAN_MSR_SLAK_BIT_POSITION      0x00000001U
+#define CAN_MSR_SLAKI_BIT_POSITION     0x00000004U
+
+/* Error Flags */
+#define CAN_ESR_EWG_BIT_POSITION       0x00000000U
+#define CAN_ESR_EPV_BIT_POSITION       0x00000001U
+#define CAN_ESR_BOF_BIT_POSITION       0x00000002U
+
+/* Mask used by macro to get/clear CAN flags*/
+#define CAN_FLAG_MASK                  0x000000FFU
+
+/* Mailboxes definition */
+#define CAN_TXMAILBOX_0   ((uint8_t)0x00)
+#define CAN_TXMAILBOX_1   ((uint8_t)0x01)
+#define CAN_TXMAILBOX_2   ((uint8_t)0x02)
+/**
+  * @}
+  */
+
+/* Exported macros -----------------------------------------------------------*/
+/** @defgroup CAN_Exported_Macros CAN Exported Macros
+  * @{
+  */
+
+/** @brief  Reset CAN handle state
+  * @param  __HANDLE__: CAN handle.
+  * @retval None
+  */
+#define __HAL_CAN_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_CAN_STATE_RESET)
+
+/**
+  * @brief  Enable the specified CAN interrupts
+  * @param  __HANDLE__: CAN handle.
+  * @param  __INTERRUPT__: CAN Interrupt.
+  *         This parameter can be one of the following values:
+  *            @arg CAN_IT_TME: Transmit mailbox empty interrupt enable
+  *            @arg CAN_IT_FMP0: FIFO 0 message pending interrupt
+  *            @arg CAN_IT_FF0 : FIFO 0 full interrupt
+  *            @arg CAN_IT_FOV0: FIFO 0 overrun interrupt
+  *            @arg CAN_IT_FMP1: FIFO 1 message pending interrupt
+  *            @arg CAN_IT_FF1 : FIFO 1 full interrupt
+  *            @arg CAN_IT_FOV1: FIFO 1 overrun interrupt
+  *            @arg CAN_IT_WKU : Wake-up interrupt
+  *            @arg CAN_IT_SLK : Sleep acknowledge interrupt
+  *            @arg CAN_IT_EWG : Error warning interrupt
+  *            @arg CAN_IT_EPV : Error passive interrupt
+  *            @arg CAN_IT_BOF : Bus-off interrupt
+  *            @arg CAN_IT_LEC : Last error code interrupt
+  *            @arg CAN_IT_ERR : Error Interrupt
+  * @retval None.
+  */
+#define __HAL_CAN_ENABLE_IT(__HANDLE__, __INTERRUPT__) (((__HANDLE__)->Instance->IER) |= (__INTERRUPT__))
+
+/**
+  * @brief  Disable the specified CAN interrupts
+  * @param  __HANDLE__: CAN handle.
+  * @param  __INTERRUPT__: CAN Interrupt.
+  *         This parameter can be one of the following values:
+  *            @arg CAN_IT_TME: Transmit mailbox empty interrupt enable
+  *            @arg CAN_IT_FMP0: FIFO 0 message pending interrupt
+  *            @arg CAN_IT_FF0 : FIFO 0 full interrupt
+  *            @arg CAN_IT_FOV0: FIFO 0 overrun interrupt
+  *            @arg CAN_IT_FMP1: FIFO 1 message pending interrupt
+  *            @arg CAN_IT_FF1 : FIFO 1 full interrupt
+  *            @arg CAN_IT_FOV1: FIFO 1 overrun interrupt
+  *            @arg CAN_IT_WKU : Wake-up interrupt
+  *            @arg CAN_IT_SLK : Sleep acknowledge interrupt
+  *            @arg CAN_IT_EWG : Error warning interrupt
+  *            @arg CAN_IT_EPV : Error passive interrupt
+  *            @arg CAN_IT_BOF : Bus-off interrupt
+  *            @arg CAN_IT_LEC : Last error code interrupt
+  *            @arg CAN_IT_ERR : Error Interrupt
+  * @retval None.
+  */
+#define __HAL_CAN_DISABLE_IT(__HANDLE__, __INTERRUPT__) (((__HANDLE__)->Instance->IER) &= ~(__INTERRUPT__))
+
+/**
+  * @brief  Return the number of pending received messages.
+  * @param  __HANDLE__: CAN handle.
+  * @param  __FIFONUMBER__: Receive FIFO number, CAN_FIFO0 or CAN_FIFO1.
+  * @retval The number of pending message.
+  */
+#define __HAL_CAN_MSG_PENDING(__HANDLE__, __FIFONUMBER__) (((__FIFONUMBER__) == CAN_FIFO0)? \
+((uint8_t)((__HANDLE__)->Instance->RF0R & 0x03U)) : ((uint8_t)((__HANDLE__)->Instance->RF1R & 0x03U)))
+
+/** @brief  Check whether the specified CAN flag is set or not.
+  * @param  __HANDLE__: specifies the CAN Handle.
+  * @param  __FLAG__: specifies the flag to check.
+  *         This parameter can be one of the following values:
+  *            @arg CAN_TSR_RQCP0: Request MailBox0 Flag
+  *            @arg CAN_TSR_RQCP1: Request MailBox1 Flag
+  *            @arg CAN_TSR_RQCP2: Request MailBox2 Flag
+  *            @arg CAN_FLAG_TXOK0: Transmission OK MailBox0 Flag
+  *            @arg CAN_FLAG_TXOK1: Transmission OK MailBox1 Flag
+  *            @arg CAN_FLAG_TXOK2: Transmission OK MailBox2 Flag
+  *            @arg CAN_FLAG_TME0: Transmit mailbox 0 empty Flag
+  *            @arg CAN_FLAG_TME1: Transmit mailbox 1 empty Flag
+  *            @arg CAN_FLAG_TME2: Transmit mailbox 2 empty Flag
+  *            @arg CAN_FLAG_FMP0: FIFO 0 Message Pending Flag
+  *            @arg CAN_FLAG_FF0: FIFO 0 Full Flag
+  *            @arg CAN_FLAG_FOV0: FIFO 0 Overrun Flag
+  *            @arg CAN_FLAG_FMP1: FIFO 1 Message Pending Flag
+  *            @arg CAN_FLAG_FF1: FIFO 1 Full Flag
+  *            @arg CAN_FLAG_FOV1: FIFO 1 Overrun Flag
+  *            @arg CAN_FLAG_WKU: Wake up Flag
+  *            @arg CAN_FLAG_SLAK: Sleep acknowledge Flag
+  *            @arg CAN_FLAG_SLAKI: Sleep acknowledge Flag
+  *            @arg CAN_FLAG_EWG: Error Warning Flag
+  *            @arg CAN_FLAG_EPV: Error Passive Flag
+  *            @arg CAN_FLAG_BOF: Bus-Off Flag
+  * @retval The new state of __FLAG__ (TRUE or FALSE).
+  */
+#define __HAL_CAN_GET_FLAG(__HANDLE__, __FLAG__) \
+((((__FLAG__) >> 8U) == 5U)? ((((__HANDLE__)->Instance->TSR) & (1U << ((__FLAG__) & CAN_FLAG_MASK))) == (1U << ((__FLAG__) & CAN_FLAG_MASK))): \
+ (((__FLAG__) >> 8U) == 2U)? ((((__HANDLE__)->Instance->RF0R) & (1U << ((__FLAG__) & CAN_FLAG_MASK))) == (1U << ((__FLAG__) & CAN_FLAG_MASK))): \
+ (((__FLAG__) >> 8U) == 4U)? ((((__HANDLE__)->Instance->RF1R) & (1U << ((__FLAG__) & CAN_FLAG_MASK))) == (1U << ((__FLAG__) & CAN_FLAG_MASK))): \
+ (((__FLAG__) >> 8U) == 1U)? ((((__HANDLE__)->Instance->MSR) & (1U << ((__FLAG__) & CAN_FLAG_MASK))) == (1U << ((__FLAG__) & CAN_FLAG_MASK))): \
+ ((((__HANDLE__)->Instance->ESR) & (1U << ((__FLAG__) & CAN_FLAG_MASK))) == (1U << ((__FLAG__) & CAN_FLAG_MASK))))
+
+/** @brief  Clear the specified CAN pending flag.
+  * @param  __HANDLE__: specifies the CAN Handle.
+  * @param  __FLAG__: specifies the flag to check.
+  *         This parameter can be one of the following values:
+  *            @arg CAN_TSR_RQCP0: Request MailBox0 Flag
+  *            @arg CAN_TSR_RQCP1: Request MailBox1 Flag
+  *            @arg CAN_TSR_RQCP2: Request MailBox2 Flag
+  *            @arg CAN_FLAG_TXOK0: Transmission OK MailBox0 Flag
+  *            @arg CAN_FLAG_TXOK1: Transmission OK MailBox1 Flag
+  *            @arg CAN_FLAG_TXOK2: Transmission OK MailBox2 Flag
+  *            @arg CAN_FLAG_TME0: Transmit mailbox 0 empty Flag
+  *            @arg CAN_FLAG_TME1: Transmit mailbox 1 empty Flag
+  *            @arg CAN_FLAG_TME2: Transmit mailbox 2 empty Flag
+  *            @arg CAN_FLAG_FMP0: FIFO 0 Message Pending Flag
+  *            @arg CAN_FLAG_FF0: FIFO 0 Full Flag
+  *            @arg CAN_FLAG_FOV0: FIFO 0 Overrun Flag
+  *            @arg CAN_FLAG_FMP1: FIFO 1 Message Pending Flag
+  *            @arg CAN_FLAG_FF1: FIFO 1 Full Flag
+  *            @arg CAN_FLAG_FOV1: FIFO 1 Overrun Flag
+  *            @arg CAN_FLAG_WKU: Wake up Flag
+  *            @arg CAN_FLAG_SLAKI: Sleep acknowledge Flag
+  * @retval The new state of __FLAG__ (TRUE or FALSE).
+  */
+#define __HAL_CAN_CLEAR_FLAG(__HANDLE__, __FLAG__) \
+((((__FLAG__) >> 8U) == TSR_REGISTER_INDEX) ? (((__HANDLE__)->Instance->TSR)  = (1U << ((__FLAG__) & CAN_FLAG_MASK))): \
+ (((__FLAG__) >> 8U) == RF0R_REGISTER_INDEX)? (((__HANDLE__)->Instance->RF0R) = (1U << ((__FLAG__) & CAN_FLAG_MASK))): \
+ (((__FLAG__) >> 8U) == RF1R_REGISTER_INDEX)? (((__HANDLE__)->Instance->RF1R) = (1U << ((__FLAG__) & CAN_FLAG_MASK))): \
+ (((__FLAG__) >> 8U) == MSR_REGISTER_INDEX) ? (((__HANDLE__)->Instance->MSR)  = (1U << ((__FLAG__) & CAN_FLAG_MASK))): 0U)
+
+/** @brief  Check if the specified CAN interrupt source is enabled or disabled.
+  * @param  __HANDLE__: specifies the CAN Handle.
+  * @param  __INTERRUPT__: specifies the CAN interrupt source to check.
+  *         This parameter can be one of the following values:
+  *            @arg CAN_IT_TME: Transmit mailbox empty interrupt enable
+  *            @arg CAN_IT_FMP0: FIFO 0 message pending interrupt
+  *            @arg CAN_IT_FF0 : FIFO 0 full interrupt
+  *            @arg CAN_IT_FOV0: FIFO 0 overrun interrupt
+  *            @arg CAN_IT_FMP1: FIFO 1 message pending interrupt
+  *            @arg CAN_IT_FF1 : FIFO 1 full interrupt
+  *            @arg CAN_IT_FOV1: FIFO 1 overrun interrupt
+  *            @arg CAN_IT_WKU : Wake-up interrupt
+  *            @arg CAN_IT_SLK : Sleep acknowledge interrupt
+  *            @arg CAN_IT_EWG : Error warning interrupt
+  *            @arg CAN_IT_EPV : Error passive interrupt
+  *            @arg CAN_IT_BOF : Bus-off interrupt
+  *            @arg CAN_IT_LEC : Last error code interrupt
+  *            @arg CAN_IT_ERR : Error Interrupt
+  * @retval The new state of __IT__ (TRUE or FALSE).
+  */
+#define __HAL_CAN_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__) ((((__HANDLE__)->Instance->IER & (__INTERRUPT__)) == (__INTERRUPT__)) ? SET : RESET)
+
+/**
+  * @brief  Check the transmission status of a CAN Frame.
+  * @param  __HANDLE__: specifies the CAN Handle.
+  * @param  __TRANSMITMAILBOX__: the number of the mailbox that is used for transmission.
+  * @retval The new status of transmission  (TRUE or FALSE).
+  */
+#define __HAL_CAN_TRANSMIT_STATUS(__HANDLE__, __TRANSMITMAILBOX__)\
+(((__TRANSMITMAILBOX__) == CAN_TXMAILBOX_0)? ((((__HANDLE__)->Instance->TSR) & (CAN_TSR_RQCP0 | CAN_TSR_TME0)) == (CAN_TSR_RQCP0 | CAN_TSR_TME0)) :\
+ ((__TRANSMITMAILBOX__) == CAN_TXMAILBOX_1)? ((((__HANDLE__)->Instance->TSR) & (CAN_TSR_RQCP1 | CAN_TSR_TME1)) == (CAN_TSR_RQCP1 | CAN_TSR_TME1)) :\
+ ((((__HANDLE__)->Instance->TSR) & (CAN_TSR_RQCP2 | CAN_TSR_TME2)) == (CAN_TSR_RQCP2 | CAN_TSR_TME2)))
+
+/**
+  * @brief  Release the specified receive FIFO.
+  * @param  __HANDLE__: CAN handle.
+  * @param  __FIFONUMBER__: Receive FIFO number, CAN_FIFO0 or CAN_FIFO1.
+  * @retval None.
+  */
+#define __HAL_CAN_FIFO_RELEASE(__HANDLE__, __FIFONUMBER__) (((__FIFONUMBER__) == CAN_FIFO0)? \
+((__HANDLE__)->Instance->RF0R = CAN_RF0R_RFOM0) : ((__HANDLE__)->Instance->RF1R = CAN_RF1R_RFOM1)) 
+
+/**
+  * @brief  Cancel a transmit request.
+  * @param  __HANDLE__: specifies the CAN Handle.
+  * @param  __TRANSMITMAILBOX__: the number of the mailbox that is used for transmission.
+  * @retval None.
+  */
+#define __HAL_CAN_CANCEL_TRANSMIT(__HANDLE__, __TRANSMITMAILBOX__)\
+(((__TRANSMITMAILBOX__) == CAN_TXMAILBOX_0)? ((__HANDLE__)->Instance->TSR = CAN_TSR_ABRQ0) :\
+ ((__TRANSMITMAILBOX__) == CAN_TXMAILBOX_1)? ((__HANDLE__)->Instance->TSR = CAN_TSR_ABRQ1) :\
+ ((__HANDLE__)->Instance->TSR = CAN_TSR_ABRQ2))
+
+/**
+  * @brief  Enable or disables the DBG Freeze for CAN.
+  * @param  __HANDLE__: specifies the CAN Handle.
+  * @param  __NEWSTATE__: new state of the CAN peripheral.
+  *         This parameter can be: ENABLE (CAN reception/transmission is frozen
+  *         during debug. Reception FIFOs can still be accessed/controlled normally)
+  *         or DISABLE (CAN is working during debug).
+  * @retval None
+  */
+#define __HAL_CAN_DBG_FREEZE(__HANDLE__, __NEWSTATE__) (((__NEWSTATE__) == ENABLE)? \
+((__HANDLE__)->Instance->MCR |= CAN_MCR_DBF) : ((__HANDLE__)->Instance->MCR &= ~CAN_MCR_DBF))
+
+/**
+  * @}
+  */
+
+/* Include CAN HAL Extension module */
+#include "stm32f1xx_hal_can_ex_legacy.h"
+
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup CAN_Exported_Functions
+  * @{
+  */
+
+/** @addtogroup CAN_Exported_Functions_Group1
+  * @brief    Initialization and Configuration functions 
+  * @{
+  */
+/* Initialization and de-initialization functions *****************************/
+HAL_StatusTypeDef HAL_CAN_Init(CAN_HandleTypeDef* hcan);
+HAL_StatusTypeDef HAL_CAN_ConfigFilter(CAN_HandleTypeDef* hcan, CAN_FilterConfTypeDef* sFilterConfig);
+HAL_StatusTypeDef HAL_CAN_DeInit(CAN_HandleTypeDef* hcan);
+void HAL_CAN_MspInit(CAN_HandleTypeDef* hcan);
+void HAL_CAN_MspDeInit(CAN_HandleTypeDef* hcan);
+/**
+  * @}
+  */
+
+/** @addtogroup CAN_Exported_Functions_Group2
+  * @brief    I/O operation functions 
+  * @{
+  */
+/* I/O operation functions *****************************************************/
+HAL_StatusTypeDef HAL_CAN_Transmit(CAN_HandleTypeDef *hcan, uint32_t Timeout);
+HAL_StatusTypeDef HAL_CAN_Transmit_IT(CAN_HandleTypeDef *hcan);
+HAL_StatusTypeDef HAL_CAN_Receive(CAN_HandleTypeDef *hcan, uint8_t FIFONumber, uint32_t Timeout);
+HAL_StatusTypeDef HAL_CAN_Receive_IT(CAN_HandleTypeDef *hcan, uint8_t FIFONumber);
+HAL_StatusTypeDef HAL_CAN_Sleep(CAN_HandleTypeDef *hcan);
+HAL_StatusTypeDef HAL_CAN_WakeUp(CAN_HandleTypeDef *hcan);
+void HAL_CAN_IRQHandler(CAN_HandleTypeDef* hcan);
+void HAL_CAN_TxCpltCallback(CAN_HandleTypeDef* hcan);
+void HAL_CAN_RxCpltCallback(CAN_HandleTypeDef* hcan);
+void HAL_CAN_ErrorCallback(CAN_HandleTypeDef *hcan);
+/**
+  * @}
+  */
+
+/** @addtogroup CAN_Exported_Functions_Group3
+  * @brief   CAN Peripheral State functions 
+  * @{
+  */
+/* Peripheral State and Error functions ***************************************/
+uint32_t HAL_CAN_GetError(CAN_HandleTypeDef *hcan);
+HAL_CAN_StateTypeDef HAL_CAN_GetState(CAN_HandleTypeDef* hcan);
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Private macros --------------------------------------------------------*/
+/** @defgroup CAN_Private_Macros   CAN Private Macros
+  * @{
+  */
+
+#define IS_CAN_MODE(MODE) (((MODE) == CAN_MODE_NORMAL) || \
+                           ((MODE) == CAN_MODE_LOOPBACK)|| \
+                           ((MODE) == CAN_MODE_SILENT) || \
+                           ((MODE) == CAN_MODE_SILENT_LOOPBACK))
+#define IS_CAN_SJW(SJW) (((SJW) == CAN_SJW_1TQ) || ((SJW) == CAN_SJW_2TQ)|| \
+                         ((SJW) == CAN_SJW_3TQ) || ((SJW) == CAN_SJW_4TQ))
+#define IS_CAN_BS1(BS1) ((BS1) <= CAN_BS1_16TQ)
+#define IS_CAN_BS2(BS2) ((BS2) <= CAN_BS2_8TQ)
+#define IS_CAN_PRESCALER(PRESCALER) (((PRESCALER) >= 1U) && ((PRESCALER) <= 1024U))
+
+#define IS_CAN_FILTER_MODE(MODE) (((MODE) == CAN_FILTERMODE_IDMASK) || \
+                                  ((MODE) == CAN_FILTERMODE_IDLIST))
+#define IS_CAN_FILTER_SCALE(SCALE) (((SCALE) == CAN_FILTERSCALE_16BIT) || \
+                                    ((SCALE) == CAN_FILTERSCALE_32BIT))
+#define IS_CAN_FILTER_FIFO(FIFO) (((FIFO) == CAN_FILTER_FIFO0) || \
+                                  ((FIFO) == CAN_FILTER_FIFO1))
+#define IS_CAN_BANKNUMBER(BANKNUMBER) ((BANKNUMBER) <= 28U)
+
+#define IS_CAN_TRANSMITMAILBOX(TRANSMITMAILBOX) ((TRANSMITMAILBOX) <= ((uint8_t)0x02))
+#define IS_CAN_STDID(STDID)   ((STDID) <= 0x00007FFU)
+#define IS_CAN_EXTID(EXTID)   ((EXTID) <= 0x1FFFFFFFU)
+#define IS_CAN_DLC(DLC)       ((DLC) <= ((uint8_t)0x08))
+
+#define IS_CAN_IDTYPE(IDTYPE)  (((IDTYPE) == CAN_ID_STD) || \
+                                ((IDTYPE) == CAN_ID_EXT))
+#define IS_CAN_RTR(RTR) (((RTR) == CAN_RTR_DATA) || ((RTR) == CAN_RTR_REMOTE))
+#define IS_CAN_FIFO(FIFO) (((FIFO) == CAN_FIFO0) || ((FIFO) == CAN_FIFO1))
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#endif /* STM32F103x6) || STM32F103xB || STM32F103xE || STM32F103xG) || STM32F105xC || STM32F107xC */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F1xx_HAL_CAN_LEGACY_H */
+
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/STM32F1xx_HAL_Driver/Inc/stm32_assert_template.h

@@ -0,0 +1,57 @@
+/**
+  ******************************************************************************
+  * @file    stm32_assert.h
+  * @author  MCD Application Team
+  * @brief   STM32 assert template file.
+  *          This file should be copied to the application folder and renamed
+  *          to stm32_assert.h.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32_ASSERT_H
+#define __STM32_ASSERT_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Exported types ------------------------------------------------------------*/
+/* Exported constants --------------------------------------------------------*/
+/* Includes ------------------------------------------------------------------*/
+/* Exported macro ------------------------------------------------------------*/
+#ifdef  USE_FULL_ASSERT
+/**
+  * @brief  The assert_param macro is used for function's parameters check.
+  * @param  expr If expr is false, it calls assert_failed function
+  *         which reports the name of the source file and the source
+  *         line number of the call that failed.
+  *         If expr is true, it returns no value.
+  * @retval None
+  */
+#define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__))
+/* Exported functions ------------------------------------------------------- */
+void assert_failed(uint8_t* file, uint32_t line);
+#else
+#define assert_param(expr) ((void)0U)
+#endif /* USE_FULL_ASSERT */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32_ASSERT_H */
+
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal.h

@@ -0,0 +1,358 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_hal.h
+  * @author  MCD Application Team
+  * @brief   This file contains all the functions prototypes for the HAL
+  *          module driver.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2017 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F1xx_HAL_H
+#define __STM32F1xx_HAL_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_hal_conf.h"
+
+/** @addtogroup STM32F1xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup HAL
+  * @{
+  */
+
+/* Exported constants --------------------------------------------------------*/
+
+/** @defgroup HAL_Exported_Constants HAL Exported Constants
+  * @{
+  */
+
+/** @defgroup HAL_TICK_FREQ Tick Frequency
+  * @{
+  */
+typedef enum
+{
+  HAL_TICK_FREQ_10HZ         = 100U,
+  HAL_TICK_FREQ_100HZ        = 10U,
+  HAL_TICK_FREQ_1KHZ         = 1U,
+  HAL_TICK_FREQ_DEFAULT      = HAL_TICK_FREQ_1KHZ
+} HAL_TickFreqTypeDef;
+/**
+  * @}
+  */
+/* Exported types ------------------------------------------------------------*/
+extern __IO uint32_t uwTick;
+extern uint32_t uwTickPrio;
+extern HAL_TickFreqTypeDef uwTickFreq;
+
+/**
+  * @}
+  */
+/* Exported macro ------------------------------------------------------------*/
+/** @defgroup HAL_Exported_Macros HAL Exported Macros
+  * @{
+  */
+
+/** @defgroup DBGMCU_Freeze_Unfreeze Freeze Unfreeze Peripherals in Debug mode
+  * @brief   Freeze/Unfreeze Peripherals in Debug mode
+  * Note: On devices STM32F10xx8 and STM32F10xxB,
+  *                  STM32F101xC/D/E and STM32F103xC/D/E,
+  *                  STM32F101xF/G and STM32F103xF/G
+  *                  STM32F10xx4 and STM32F10xx6
+  *       Debug registers DBGMCU_IDCODE and DBGMCU_CR are accessible only in
+  *       debug mode (not accessible by the user software in normal mode).
+  *       Refer to errata sheet of these devices for more details.
+  * @{
+  */
+
+/* Peripherals on APB1 */
+/**
+  * @brief  TIM2 Peripherals Debug mode
+  */
+#define __HAL_DBGMCU_FREEZE_TIM2()            SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM2_STOP)
+#define __HAL_DBGMCU_UNFREEZE_TIM2()          CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM2_STOP)
+
+/**
+  * @brief  TIM3 Peripherals Debug mode
+  */
+#define __HAL_DBGMCU_FREEZE_TIM3()            SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM3_STOP)
+#define __HAL_DBGMCU_UNFREEZE_TIM3()          CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM3_STOP)
+
+#if defined (DBGMCU_CR_DBG_TIM4_STOP)
+/**
+  * @brief  TIM4 Peripherals Debug mode
+  */
+#define __HAL_DBGMCU_FREEZE_TIM4()            SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM4_STOP)
+#define __HAL_DBGMCU_UNFREEZE_TIM4()          CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM4_STOP)
+#endif
+
+#if defined (DBGMCU_CR_DBG_TIM5_STOP)
+/**
+  * @brief  TIM5 Peripherals Debug mode
+  */
+#define __HAL_DBGMCU_FREEZE_TIM5()            SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM5_STOP)
+#define __HAL_DBGMCU_UNFREEZE_TIM5()          CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM5_STOP)
+#endif
+
+#if defined (DBGMCU_CR_DBG_TIM6_STOP)
+/**
+  * @brief  TIM6 Peripherals Debug mode
+  */
+#define __HAL_DBGMCU_FREEZE_TIM6()            SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM6_STOP)
+#define __HAL_DBGMCU_UNFREEZE_TIM6()          CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM6_STOP)
+#endif
+
+#if defined (DBGMCU_CR_DBG_TIM7_STOP)
+/**
+  * @brief  TIM7 Peripherals Debug mode
+  */
+#define __HAL_DBGMCU_FREEZE_TIM7()            SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM7_STOP)
+#define __HAL_DBGMCU_UNFREEZE_TIM7()          CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM7_STOP)
+#endif
+
+#if defined (DBGMCU_CR_DBG_TIM12_STOP)
+/**
+  * @brief  TIM12 Peripherals Debug mode
+  */
+#define __HAL_DBGMCU_FREEZE_TIM12()            SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM12_STOP)
+#define __HAL_DBGMCU_UNFREEZE_TIM12()          CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM12_STOP)
+#endif
+
+#if defined (DBGMCU_CR_DBG_TIM13_STOP)
+/**
+  * @brief  TIM13 Peripherals Debug mode
+  */
+#define __HAL_DBGMCU_FREEZE_TIM13()            SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM13_STOP)
+#define __HAL_DBGMCU_UNFREEZE_TIM13()          CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM13_STOP)
+#endif
+
+#if defined (DBGMCU_CR_DBG_TIM14_STOP)
+/**
+  * @brief  TIM14 Peripherals Debug mode
+  */
+#define __HAL_DBGMCU_FREEZE_TIM14()            SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM14_STOP)
+#define __HAL_DBGMCU_UNFREEZE_TIM14()          CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM14_STOP)
+#endif
+
+/**
+  * @brief  WWDG Peripherals Debug mode
+  */
+#define __HAL_DBGMCU_FREEZE_WWDG()            SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_WWDG_STOP)
+#define __HAL_DBGMCU_UNFREEZE_WWDG()          CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_WWDG_STOP)
+
+/**
+  * @brief  IWDG Peripherals Debug mode
+  */
+#define __HAL_DBGMCU_FREEZE_IWDG()            SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_IWDG_STOP)
+#define __HAL_DBGMCU_UNFREEZE_IWDG()          CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_IWDG_STOP)
+
+/**
+  * @brief  I2C1 Peripherals Debug mode
+  */
+#define __HAL_DBGMCU_FREEZE_I2C1_TIMEOUT()    SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_I2C1_SMBUS_TIMEOUT)
+#define __HAL_DBGMCU_UNFREEZE_I2C1_TIMEOUT()  CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_I2C1_SMBUS_TIMEOUT)
+
+#if defined (DBGMCU_CR_DBG_I2C2_SMBUS_TIMEOUT)
+/**
+  * @brief  I2C2 Peripherals Debug mode
+  */
+#define __HAL_DBGMCU_FREEZE_I2C2_TIMEOUT()    SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_I2C2_SMBUS_TIMEOUT)
+#define __HAL_DBGMCU_UNFREEZE_I2C2_TIMEOUT()  CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_I2C2_SMBUS_TIMEOUT)
+#endif
+
+#if defined (DBGMCU_CR_DBG_CAN1_STOP)
+/**
+  * @brief  CAN1 Peripherals Debug mode
+  */
+#define __HAL_DBGMCU_FREEZE_CAN1()            SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_CAN1_STOP)
+#define __HAL_DBGMCU_UNFREEZE_CAN1()          CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_CAN1_STOP)
+#endif
+
+#if defined (DBGMCU_CR_DBG_CAN2_STOP)
+/**
+  * @brief  CAN2 Peripherals Debug mode
+  */
+#define __HAL_DBGMCU_FREEZE_CAN2()            SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_CAN2_STOP)
+#define __HAL_DBGMCU_UNFREEZE_CAN2()          CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_CAN2_STOP)
+#endif
+
+/* Peripherals on APB2 */
+#if defined (DBGMCU_CR_DBG_TIM1_STOP)
+/**
+  * @brief  TIM1 Peripherals Debug mode
+  */
+#define __HAL_DBGMCU_FREEZE_TIM1()            SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM1_STOP)
+#define __HAL_DBGMCU_UNFREEZE_TIM1()          CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM1_STOP)
+#endif
+
+#if defined (DBGMCU_CR_DBG_TIM8_STOP)
+/**
+  * @brief  TIM8 Peripherals Debug mode
+  */
+#define __HAL_DBGMCU_FREEZE_TIM8()            SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM8_STOP)
+#define __HAL_DBGMCU_UNFREEZE_TIM8()          CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM8_STOP)
+#endif
+
+#if defined (DBGMCU_CR_DBG_TIM9_STOP)
+/**
+  * @brief  TIM9 Peripherals Debug mode
+  */
+#define __HAL_DBGMCU_FREEZE_TIM9()            SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM9_STOP)
+#define __HAL_DBGMCU_UNFREEZE_TIM9()          CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM9_STOP)
+#endif
+
+#if defined (DBGMCU_CR_DBG_TIM10_STOP)
+/**
+  * @brief  TIM10 Peripherals Debug mode
+  */
+#define __HAL_DBGMCU_FREEZE_TIM10()            SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM10_STOP)
+#define __HAL_DBGMCU_UNFREEZE_TIM10()          CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM10_STOP)
+#endif
+
+#if defined (DBGMCU_CR_DBG_TIM11_STOP)
+/**
+  * @brief  TIM11 Peripherals Debug mode
+  */
+#define __HAL_DBGMCU_FREEZE_TIM11()            SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM11_STOP)
+#define __HAL_DBGMCU_UNFREEZE_TIM11()          CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM11_STOP)
+#endif
+
+
+#if defined (DBGMCU_CR_DBG_TIM15_STOP)
+/**
+  * @brief  TIM15 Peripherals Debug mode
+  */
+#define __HAL_DBGMCU_FREEZE_TIM15()            SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM15_STOP)
+#define __HAL_DBGMCU_UNFREEZE_TIM15()          CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM15_STOP)
+#endif
+
+#if defined (DBGMCU_CR_DBG_TIM16_STOP)
+/**
+  * @brief  TIM16 Peripherals Debug mode
+  */
+#define __HAL_DBGMCU_FREEZE_TIM16()            SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM16_STOP)
+#define __HAL_DBGMCU_UNFREEZE_TIM16()          CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM16_STOP)
+#endif
+
+#if defined (DBGMCU_CR_DBG_TIM17_STOP)
+/**
+  * @brief  TIM17 Peripherals Debug mode
+  */
+#define __HAL_DBGMCU_FREEZE_TIM17()            SET_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM17_STOP)
+#define __HAL_DBGMCU_UNFREEZE_TIM17()          CLEAR_BIT(DBGMCU->CR, DBGMCU_CR_DBG_TIM17_STOP)
+#endif
+
+/**
+  * @}
+  */
+
+/** @defgroup HAL_Private_Macros HAL Private Macros
+  * @{
+  */
+#define IS_TICKFREQ(FREQ) (((FREQ) == HAL_TICK_FREQ_10HZ)  || \
+                           ((FREQ) == HAL_TICK_FREQ_100HZ) || \
+                           ((FREQ) == HAL_TICK_FREQ_1KHZ))
+/**
+  * @}
+  */
+
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup HAL_Exported_Functions
+  * @{
+  */
+/** @addtogroup HAL_Exported_Functions_Group1
+  * @{
+  */
+/* Initialization and de-initialization functions  ******************************/
+HAL_StatusTypeDef HAL_Init(void);
+HAL_StatusTypeDef HAL_DeInit(void);
+void HAL_MspInit(void);
+void HAL_MspDeInit(void);
+HAL_StatusTypeDef HAL_InitTick(uint32_t TickPriority);
+/**
+  * @}
+  */
+
+/** @addtogroup HAL_Exported_Functions_Group2
+  * @{
+  */
+/* Peripheral Control functions  ************************************************/
+void HAL_IncTick(void);
+void HAL_Delay(uint32_t Delay);
+uint32_t HAL_GetTick(void);
+uint32_t HAL_GetTickPrio(void);
+HAL_StatusTypeDef HAL_SetTickFreq(HAL_TickFreqTypeDef Freq);
+HAL_TickFreqTypeDef HAL_GetTickFreq(void);
+void HAL_SuspendTick(void);
+void HAL_ResumeTick(void);
+uint32_t HAL_GetHalVersion(void);
+uint32_t HAL_GetREVID(void);
+uint32_t HAL_GetDEVID(void);
+uint32_t HAL_GetUIDw0(void);
+uint32_t HAL_GetUIDw1(void);
+uint32_t HAL_GetUIDw2(void);
+void HAL_DBGMCU_EnableDBGSleepMode(void);
+void HAL_DBGMCU_DisableDBGSleepMode(void);
+void HAL_DBGMCU_EnableDBGStopMode(void);
+void HAL_DBGMCU_DisableDBGStopMode(void);
+void HAL_DBGMCU_EnableDBGStandbyMode(void);
+void HAL_DBGMCU_DisableDBGStandbyMode(void);
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+/* Private types -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/** @defgroup HAL_Private_Variables HAL Private Variables
+  * @{
+  */
+/**
+  * @}
+  */
+/* Private constants ---------------------------------------------------------*/
+/** @defgroup HAL_Private_Constants HAL Private Constants
+  * @{
+  */
+/**
+  * @}
+  */
+/* Private macros ------------------------------------------------------------*/
+/* Private functions ---------------------------------------------------------*/
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F1xx_HAL_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_adc_ex.h

@@ -0,0 +1,710 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_hal_adc_ex.h
+  * @author  MCD Application Team
+  * @brief   Header file of ADC HAL extension module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F1xx_HAL_ADC_EX_H
+#define __STM32F1xx_HAL_ADC_EX_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_hal_def.h"  
+
+/** @addtogroup STM32F1xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup ADCEx
+  * @{
+  */ 
+
+/* Exported types ------------------------------------------------------------*/ 
+/** @defgroup ADCEx_Exported_Types ADCEx Exported Types
+  * @{
+  */
+
+/** 
+  * @brief  ADC Configuration injected Channel structure definition
+  * @note   Parameters of this structure are shared within 2 scopes:
+  *          - Scope channel: InjectedChannel, InjectedRank, InjectedSamplingTime, InjectedOffset
+  *          - Scope injected group (affects all channels of injected group): InjectedNbrOfConversion, InjectedDiscontinuousConvMode,
+  *            AutoInjectedConv, ExternalTrigInjecConvEdge, ExternalTrigInjecConv.
+  * @note   The setting of these parameters with function HAL_ADCEx_InjectedConfigChannel() is conditioned to ADC state.
+  *         ADC state can be either:
+  *          - For all parameters: ADC disabled (this is the only possible ADC state to modify parameter 'ExternalTrigInjecConv')
+  *          - For all except parameters 'ExternalTrigInjecConv': ADC enabled without conversion on going on injected group.
+  */
+typedef struct 
+{
+  uint32_t InjectedChannel;                       /*!< Selection of ADC channel to configure
+                                                       This parameter can be a value of @ref ADC_channels
+                                                       Note: Depending on devices, some channels may not be available on package pins. Refer to device datasheet for channels availability.
+                                                       Note: On STM32F1 devices with several ADC: Only ADC1 can access internal measurement channels (VrefInt/TempSensor)
+                                                       Note: On STM32F10xx8 and STM32F10xxB devices: A low-amplitude voltage glitch may be generated (on ADC input 0) on the PA0 pin, when the ADC is converting with injection trigger.
+                                                             It is advised to distribute the analog channels so that Channel 0 is configured as an injected channel.
+                                                             Refer to errata sheet of these devices for more details. */
+  uint32_t InjectedRank;                          /*!< Rank in the injected group sequencer
+                                                       This parameter must be a value of @ref ADCEx_injected_rank
+                                                       Note: In case of need to disable a channel or change order of conversion sequencer, rank containing a previous channel setting can be overwritten by the new channel setting (or parameter number of conversions can be adjusted) */
+  uint32_t InjectedSamplingTime;                  /*!< Sampling time value to be set for the selected channel.
+                                                       Unit: ADC clock cycles
+                                                       Conversion time is the addition of sampling time and processing time (12.5 ADC clock cycles at ADC resolution 12 bits).
+                                                       This parameter can be a value of @ref ADC_sampling_times
+                                                       Caution: This parameter updates the parameter property of the channel, that can be used into regular and/or injected groups.
+                                                                If this same channel has been previously configured in the other group (regular/injected), it will be updated to last setting.
+                                                       Note: In case of usage of internal measurement channels (VrefInt/TempSensor),
+                                                             sampling time constraints must be respected (sampling time can be adjusted in function of ADC clock frequency and sampling time setting)
+                                                             Refer to device datasheet for timings values, parameters TS_vrefint, TS_temp (values rough order: 5us to 17.1us min). */
+  uint32_t InjectedOffset;                        /*!< Defines the offset to be subtracted from the raw converted data (for channels set on injected group only).
+                                                       Offset value must be a positive number.
+                                                       Depending of ADC resolution selected (12, 10, 8 or 6 bits),
+                                                       this parameter must be a number between Min_Data = 0x000 and Max_Data = 0xFFF, 0x3FF, 0xFF or 0x3F respectively. */
+  uint32_t InjectedNbrOfConversion;               /*!< Specifies the number of ranks that will be converted within the injected group sequencer.
+                                                       To use the injected group sequencer and convert several ranks, parameter 'ScanConvMode' must be enabled.
+                                                       This parameter must be a number between Min_Data = 1 and Max_Data = 4.
+                                                       Caution: this setting impacts the entire injected group. Therefore, call of HAL_ADCEx_InjectedConfigChannel() to
+                                                                configure a channel on injected group can impact the configuration of other channels previously set. */
+  FunctionalState InjectedDiscontinuousConvMode;  /*!< Specifies whether the conversions sequence of injected group is performed in Complete-sequence/Discontinuous-sequence (main sequence subdivided in successive parts).
+                                                       Discontinuous mode is used only if sequencer is enabled (parameter 'ScanConvMode'). If sequencer is disabled, this parameter is discarded.
+                                                       Discontinuous mode can be enabled only if continuous mode is disabled. If continuous mode is enabled, this parameter setting is discarded.
+                                                       This parameter can be set to ENABLE or DISABLE.
+                                                       Note: For injected group, number of discontinuous ranks increment is fixed to one-by-one.
+                                                       Caution: this setting impacts the entire injected group. Therefore, call of HAL_ADCEx_InjectedConfigChannel() to
+                                                                configure a channel on injected group can impact the configuration of other channels previously set. */
+  FunctionalState AutoInjectedConv;               /*!< Enables or disables the selected ADC automatic injected group conversion after regular one
+                                                       This parameter can be set to ENABLE or DISABLE.
+                                                       Note: To use Automatic injected conversion, discontinuous mode must be disabled ('DiscontinuousConvMode' and 'InjectedDiscontinuousConvMode' set to DISABLE)
+                                                       Note: To use Automatic injected conversion, injected group external triggers must be disabled ('ExternalTrigInjecConv' set to ADC_SOFTWARE_START)
+                                                       Note: In case of DMA used with regular group: if DMA configured in normal mode (single shot) JAUTO will be stopped upon DMA transfer complete.
+                                                             To maintain JAUTO always enabled, DMA must be configured in circular mode.
+                                                       Caution: this setting impacts the entire injected group. Therefore, call of HAL_ADCEx_InjectedConfigChannel() to
+                                                                configure a channel on injected group can impact the configuration of other channels previously set. */
+  uint32_t ExternalTrigInjecConv;                 /*!< Selects the external event used to trigger the conversion start of injected group.
+                                                       If set to ADC_INJECTED_SOFTWARE_START, external triggers are disabled.
+                                                       If set to external trigger source, triggering is on event rising edge.
+                                                       This parameter can be a value of @ref ADCEx_External_trigger_source_Injected
+                                                       Note: This parameter must be modified when ADC is disabled (before ADC start conversion or after ADC stop conversion).
+                                                             If ADC is enabled, this parameter setting is bypassed without error reporting (as it can be the expected behaviour in case of another parameter update on the fly)
+                                                       Caution: this setting impacts the entire injected group. Therefore, call of HAL_ADCEx_InjectedConfigChannel() to
+                                                                configure a channel on injected group can impact the configuration of other channels previously set. */
+}ADC_InjectionConfTypeDef;
+
+#if defined (STM32F103x6) || defined (STM32F103xB) || defined (STM32F105xC) || defined (STM32F107xC) || defined (STM32F103xE) || defined (STM32F103xG)
+/** 
+  * @brief  Structure definition of ADC multimode
+  * @note   The setting of these parameters with function HAL_ADCEx_MultiModeConfigChannel() is conditioned to ADCs state (both ADCs of the common group).
+  *         State of ADCs of the common group must be: disabled.
+  */
+typedef struct
+{
+  uint32_t Mode;              /*!< Configures the ADC to operate in independent or multi mode. 
+                                   This parameter can be a value of @ref ADCEx_Common_mode
+                                   Note: In dual mode, a change of channel configuration generates a restart that can produce a loss of synchronization. It is recommended to disable dual mode before any configuration change.
+                                   Note: In case of simultaneous mode used: Exactly the same sampling time should be configured for the 2 channels that will be sampled simultaneously by ACD1 and ADC2.
+                                   Note: In case of interleaved mode used: To avoid overlap between conversions, maximum sampling time allowed is 7 ADC clock cycles for fast interleaved mode and 14 ADC clock cycles for slow interleaved mode.
+                                   Note: Some multimode parameters are fixed on STM32F1 and can be configured on other STM32 devices with several ADC (multimode configuration structure can have additional parameters).
+                                         The equivalences are:
+                                           - Parameter 'DMAAccessMode': On STM32F1, this parameter is fixed to 1 DMA channel (one DMA channel for both ADC, DMA of ADC master). On other STM32 devices with several ADC, this is equivalent to parameter 'ADC_DMAACCESSMODE_12_10_BITS'.
+                                           - Parameter 'TwoSamplingDelay': On STM32F1, this parameter is fixed to 7 or 14 ADC clock cycles depending on fast or slow interleaved mode selected. On other STM32 devices with several ADC, this is equivalent to parameter 'ADC_TWOSAMPLINGDELAY_7CYCLES' (for fast interleaved mode). */
+
+  
+}ADC_MultiModeTypeDef;                                                          
+#endif /* defined STM32F103x6 || defined STM32F103xB || defined STM32F105xC || defined STM32F107xC || defined STM32F103xE || defined STM32F103xG */
+
+/**
+  * @}
+  */
+
+
+/* Exported constants --------------------------------------------------------*/
+   
+/** @defgroup ADCEx_Exported_Constants ADCEx Exported Constants
+  * @{
+  */
+
+/** @defgroup ADCEx_injected_rank ADCEx rank into injected group
+  * @{
+  */
+#define ADC_INJECTED_RANK_1                           0x00000001U
+#define ADC_INJECTED_RANK_2                           0x00000002U
+#define ADC_INJECTED_RANK_3                           0x00000003U
+#define ADC_INJECTED_RANK_4                           0x00000004U
+/**
+  * @}
+  */
+
+/** @defgroup ADCEx_External_trigger_edge_Injected ADCEx external trigger enable for injected group
+  * @{
+  */
+#define ADC_EXTERNALTRIGINJECCONV_EDGE_NONE           0x00000000U
+#define ADC_EXTERNALTRIGINJECCONV_EDGE_RISING         ((uint32_t)ADC_CR2_JEXTTRIG)
+/**
+  * @}
+  */
+    
+/** @defgroup ADC_External_trigger_source_Regular ADC External trigger selection for regular group
+  * @{
+  */
+/*!< List of external triggers with generic trigger name, independently of    */
+/* ADC target, sorted by trigger name:                                        */
+
+/*!< External triggers of regular group for ADC1&ADC2 only */
+#define ADC_EXTERNALTRIGCONV_T1_CC1         ADC1_2_EXTERNALTRIG_T1_CC1
+#define ADC_EXTERNALTRIGCONV_T1_CC2         ADC1_2_EXTERNALTRIG_T1_CC2
+#define ADC_EXTERNALTRIGCONV_T2_CC2         ADC1_2_EXTERNALTRIG_T2_CC2
+#define ADC_EXTERNALTRIGCONV_T3_TRGO        ADC1_2_EXTERNALTRIG_T3_TRGO
+#define ADC_EXTERNALTRIGCONV_T4_CC4         ADC1_2_EXTERNALTRIG_T4_CC4
+#define ADC_EXTERNALTRIGCONV_EXT_IT11       ADC1_2_EXTERNALTRIG_EXT_IT11
+
+#if defined (STM32F103xE) || defined (STM32F103xG)
+/*!< External triggers of regular group for ADC3 only */
+#define ADC_EXTERNALTRIGCONV_T2_CC3         ADC3_EXTERNALTRIG_T2_CC3
+#define ADC_EXTERNALTRIGCONV_T3_CC1         ADC3_EXTERNALTRIG_T3_CC1
+#define ADC_EXTERNALTRIGCONV_T5_CC1         ADC3_EXTERNALTRIG_T5_CC1
+#define ADC_EXTERNALTRIGCONV_T5_CC3         ADC3_EXTERNALTRIG_T5_CC3
+#define ADC_EXTERNALTRIGCONV_T8_CC1         ADC3_EXTERNALTRIG_T8_CC1
+#endif /* STM32F103xE || defined STM32F103xG */
+
+/*!< External triggers of regular group for all ADC instances */
+#define ADC_EXTERNALTRIGCONV_T1_CC3         ADC1_2_3_EXTERNALTRIG_T1_CC3
+
+#if defined (STM32F101xE) || defined (STM32F103xE) || defined (STM32F103xG) || defined (STM32F105xC) || defined (STM32F107xC)
+/*!< Note: TIM8_TRGO is available on ADC1 and ADC2 only in high-density and   */
+/*         XL-density devices.                                                */
+/*         To use it on ADC or ADC2, a remap of trigger must be done from     */
+/*         EXTI line 11 to TIM8_TRGO with macro:                              */
+/*           __HAL_AFIO_REMAP_ADC1_ETRGREG_ENABLE()                           */
+/*           __HAL_AFIO_REMAP_ADC2_ETRGREG_ENABLE()                           */
+
+/* Note for internal constant value management: If TIM8_TRGO is available,    */
+/* its definition is set to value for ADC1&ADC2 by default and changed to     */
+/* value for ADC3 by HAL ADC driver if ADC3 is selected.                      */
+#define ADC_EXTERNALTRIGCONV_T8_TRGO        ADC1_2_EXTERNALTRIG_T8_TRGO
+#endif /* STM32F101xE || STM32F103xE || STM32F103xG || STM32F105xC || STM32F107xC */
+
+#define ADC_SOFTWARE_START                  ADC1_2_3_SWSTART
+/**
+  * @}
+  */
+
+/** @defgroup ADCEx_External_trigger_source_Injected ADCEx External trigger selection for injected group
+  * @{
+  */
+/*!< List of external triggers with generic trigger name, independently of    */
+/* ADC target, sorted by trigger name:                                        */
+
+/*!< External triggers of injected group for ADC1&ADC2 only */
+#define ADC_EXTERNALTRIGINJECCONV_T2_TRGO        ADC1_2_EXTERNALTRIGINJEC_T2_TRGO
+#define ADC_EXTERNALTRIGINJECCONV_T2_CC1         ADC1_2_EXTERNALTRIGINJEC_T2_CC1
+#define ADC_EXTERNALTRIGINJECCONV_T3_CC4         ADC1_2_EXTERNALTRIGINJEC_T3_CC4
+#define ADC_EXTERNALTRIGINJECCONV_T4_TRGO        ADC1_2_EXTERNALTRIGINJEC_T4_TRGO 
+#define ADC_EXTERNALTRIGINJECCONV_EXT_IT15       ADC1_2_EXTERNALTRIGINJEC_EXT_IT15
+
+#if defined (STM32F103xE) || defined (STM32F103xG)
+/*!< External triggers of injected group for ADC3 only */
+#define ADC_EXTERNALTRIGINJECCONV_T4_CC3         ADC3_EXTERNALTRIGINJEC_T4_CC3
+#define ADC_EXTERNALTRIGINJECCONV_T8_CC2         ADC3_EXTERNALTRIGINJEC_T8_CC2
+#define ADC_EXTERNALTRIGINJECCONV_T5_TRGO        ADC3_EXTERNALTRIGINJEC_T5_TRGO
+#define ADC_EXTERNALTRIGINJECCONV_T5_CC4         ADC3_EXTERNALTRIGINJEC_T5_CC4
+#endif /* STM32F103xE || defined STM32F103xG */
+
+/*!< External triggers of injected group for all ADC instances */
+#define ADC_EXTERNALTRIGINJECCONV_T1_CC4         ADC1_2_3_EXTERNALTRIGINJEC_T1_CC4
+#define ADC_EXTERNALTRIGINJECCONV_T1_TRGO        ADC1_2_3_EXTERNALTRIGINJEC_T1_TRGO
+
+#if defined (STM32F101xE) || defined (STM32F103xE) || defined (STM32F103xG) || defined (STM32F105xC) || defined (STM32F107xC)
+/*!< Note: TIM8_CC4 is available on ADC1 and ADC2 only in high-density and    */
+/*         XL-density devices.                                                */
+/*         To use it on ADC1 or ADC2, a remap of trigger must be done from    */
+/*         EXTI line 11 to TIM8_CC4 with macro:                               */
+/*           __HAL_AFIO_REMAP_ADC1_ETRGINJ_ENABLE()                           */
+/*           __HAL_AFIO_REMAP_ADC2_ETRGINJ_ENABLE()                           */
+
+/* Note for internal constant value management: If TIM8_CC4 is available,     */
+/* its definition is set to value for ADC1&ADC2 by default and changed to     */
+/* value for ADC3 by HAL ADC driver if ADC3 is selected.                      */
+#define ADC_EXTERNALTRIGINJECCONV_T8_CC4         ADC1_2_EXTERNALTRIGINJEC_T8_CC4
+#endif /* STM32F101xE || STM32F103xE || STM32F103xG || STM32F105xC || STM32F107xC */
+
+#define ADC_INJECTED_SOFTWARE_START              ADC1_2_3_JSWSTART
+/**
+  * @}
+  */
+
+#if defined (STM32F103x6) || defined (STM32F103xB) || defined (STM32F105xC) || defined (STM32F107xC) || defined (STM32F103xE) || defined (STM32F103xG)
+/** @defgroup ADCEx_Common_mode ADC Extended Dual ADC Mode
+  * @{
+  */
+#define ADC_MODE_INDEPENDENT                              0x00000000U                                                                     /*!< ADC dual mode disabled (ADC independent mode) */
+#define ADC_DUALMODE_REGSIMULT_INJECSIMULT    ((uint32_t)(                                                            ADC_CR1_DUALMOD_0)) /*!< ADC dual mode enabled: Combined regular simultaneous + injected simultaneous mode, on groups regular and injected */
+#define ADC_DUALMODE_REGSIMULT_ALTERTRIG      ((uint32_t)(                                        ADC_CR1_DUALMOD_1                    )) /*!< ADC dual mode enabled: Combined regular simultaneous + alternate trigger mode, on groups regular and injected */
+#define ADC_DUALMODE_INJECSIMULT_INTERLFAST   ((uint32_t)(                                        ADC_CR1_DUALMOD_1 | ADC_CR1_DUALMOD_0)) /*!< ADC dual mode enabled: Combined injected simultaneous + fast interleaved mode, on groups regular and injected (delay between ADC sampling phases: 7 ADC clock cycles (equivalent to parameter "TwoSamplingDelay" set to "ADC_TWOSAMPLINGDELAY_7CYCLES" on other STM32 devices)) */
+#define ADC_DUALMODE_INJECSIMULT_INTERLSLOW   ((uint32_t)(                    ADC_CR1_DUALMOD_2                                        )) /*!< ADC dual mode enabled: Combined injected simultaneous + slow Interleaved mode, on groups regular and injected (delay between ADC sampling phases: 14 ADC clock cycles (equivalent to parameter "TwoSamplingDelay" set to "ADC_TWOSAMPLINGDELAY_7CYCLES" on other STM32 devices)) */
+#define ADC_DUALMODE_INJECSIMULT              ((uint32_t)(                    ADC_CR1_DUALMOD_2 |                     ADC_CR1_DUALMOD_0)) /*!< ADC dual mode enabled: Injected simultaneous mode, on group injected */
+#define ADC_DUALMODE_REGSIMULT                ((uint32_t)(                    ADC_CR1_DUALMOD_2 | ADC_CR1_DUALMOD_1                    )) /*!< ADC dual mode enabled: Regular simultaneous mode, on group regular */
+#define ADC_DUALMODE_INTERLFAST               ((uint32_t)(                    ADC_CR1_DUALMOD_2 | ADC_CR1_DUALMOD_1 | ADC_CR1_DUALMOD_0)) /*!< ADC dual mode enabled: Fast interleaved mode, on group regular (delay between ADC sampling phases: 7 ADC clock cycles (equivalent to parameter "TwoSamplingDelay" set to "ADC_TWOSAMPLINGDELAY_7CYCLES" on other STM32 devices)) */
+#define ADC_DUALMODE_INTERLSLOW               ((uint32_t)(ADC_CR1_DUALMOD_3                                                            )) /*!< ADC dual mode enabled: Slow interleaved mode, on group regular (delay between ADC sampling phases: 14 ADC clock cycles (equivalent to parameter "TwoSamplingDelay" set to "ADC_TWOSAMPLINGDELAY_7CYCLES" on other STM32 devices)) */
+#define ADC_DUALMODE_ALTERTRIG                ((uint32_t)(ADC_CR1_DUALMOD_3 |                                         ADC_CR1_DUALMOD_0)) /*!< ADC dual mode enabled: Alternate trigger mode, on group injected */
+/**
+  * @}
+  */
+#endif /* defined STM32F103x6 || defined STM32F103xB || defined STM32F105xC || defined STM32F107xC || defined STM32F103xE || defined STM32F103xG */
+
+/**
+  * @}
+  */
+
+
+/* Private constants ---------------------------------------------------------*/
+
+/** @addtogroup ADCEx_Private_Constants ADCEx Private Constants
+  * @{
+  */
+
+/** @defgroup ADCEx_Internal_HAL_driver_Ext_trig_src_Regular ADC Extended Internal HAL driver trigger selection for regular group
+  * @{
+  */
+/* List of external triggers of regular group for ADC1, ADC2, ADC3 (if ADC    */
+/* instance is available on the selected device).                             */
+/* (used internally by HAL driver. To not use into HAL structure parameters)  */
+
+/* External triggers of regular group for ADC1&ADC2 (if ADCx available) */
+#define ADC1_2_EXTERNALTRIG_T1_CC1                       0x00000000U
+#define ADC1_2_EXTERNALTRIG_T1_CC2           ((uint32_t)(                                      ADC_CR2_EXTSEL_0))
+#define ADC1_2_EXTERNALTRIG_T2_CC2           ((uint32_t)(                   ADC_CR2_EXTSEL_1 | ADC_CR2_EXTSEL_0))
+#define ADC1_2_EXTERNALTRIG_T3_TRGO          ((uint32_t)(ADC_CR2_EXTSEL_2                                      ))
+#define ADC1_2_EXTERNALTRIG_T4_CC4           ((uint32_t)(ADC_CR2_EXTSEL_2 |                    ADC_CR2_EXTSEL_0))
+#define ADC1_2_EXTERNALTRIG_EXT_IT11         ((uint32_t)(ADC_CR2_EXTSEL_2 | ADC_CR2_EXTSEL_1                   ))
+#if defined (STM32F101xE) || defined (STM32F103xE) || defined (STM32F103xG)
+/* Note: TIM8_TRGO is available on ADC1 and ADC2 only in high-density and     */
+/* XL-density devices.                                                        */
+#define ADC1_2_EXTERNALTRIG_T8_TRGO          ADC1_2_EXTERNALTRIG_EXT_IT11
+#endif
+
+#if defined (STM32F103xE) || defined (STM32F103xG)
+/* External triggers of regular group for ADC3 */
+#define ADC3_EXTERNALTRIG_T3_CC1             ADC1_2_EXTERNALTRIG_T1_CC1
+#define ADC3_EXTERNALTRIG_T2_CC3             ADC1_2_EXTERNALTRIG_T1_CC2
+#define ADC3_EXTERNALTRIG_T8_CC1             ADC1_2_EXTERNALTRIG_T2_CC2
+#define ADC3_EXTERNALTRIG_T8_TRGO            ADC1_2_EXTERNALTRIG_T3_TRGO
+#define ADC3_EXTERNALTRIG_T5_CC1             ADC1_2_EXTERNALTRIG_T4_CC4
+#define ADC3_EXTERNALTRIG_T5_CC3             ADC1_2_EXTERNALTRIG_EXT_IT11
+#endif
+
+/* External triggers of regular group for ADC1&ADC2&ADC3 (if ADCx available) */
+#define ADC1_2_3_EXTERNALTRIG_T1_CC3         ((uint32_t)(                   ADC_CR2_EXTSEL_1                   ))
+#define ADC1_2_3_SWSTART                     ((uint32_t)(ADC_CR2_EXTSEL_2 | ADC_CR2_EXTSEL_1 | ADC_CR2_EXTSEL_0))
+/**
+  * @}
+  */
+
+/** @defgroup ADCEx_Internal_HAL_driver_Ext_trig_src_Injected ADC Extended Internal HAL driver trigger selection for injected group
+  * @{
+  */
+/* List of external triggers of injected group for ADC1, ADC2, ADC3 (if ADC    */
+/* instance is available on the selected device).                             */
+/* (used internally by HAL driver. To not use into HAL structure parameters)  */
+
+/* External triggers of injected group for ADC1&ADC2 (if ADCx available) */
+#define ADC1_2_EXTERNALTRIGINJEC_T2_TRGO          ((uint32_t)(                    ADC_CR2_JEXTSEL_1                    ))
+#define ADC1_2_EXTERNALTRIGINJEC_T2_CC1           ((uint32_t)(                    ADC_CR2_JEXTSEL_1 | ADC_CR2_JEXTSEL_0))
+#define ADC1_2_EXTERNALTRIGINJEC_T3_CC4           ((uint32_t)(ADC_CR2_JEXTSEL_2                                        ))
+#define ADC1_2_EXTERNALTRIGINJEC_T4_TRGO          ((uint32_t)(ADC_CR2_JEXTSEL_2 |                     ADC_CR2_JEXTSEL_0))
+#define ADC1_2_EXTERNALTRIGINJEC_EXT_IT15         ((uint32_t)(ADC_CR2_JEXTSEL_2 | ADC_CR2_JEXTSEL_1                    ))
+#if defined (STM32F101xE) || defined (STM32F103xE) || defined (STM32F103xG)
+/* Note: TIM8_CC4 is available on ADC1 and ADC2 only in high-density and      */
+/* XL-density devices.                                                        */
+#define ADC1_2_EXTERNALTRIGINJEC_T8_CC4           ADC1_2_EXTERNALTRIGINJEC_EXT_IT15
+#endif
+
+#if defined (STM32F103xE) || defined (STM32F103xG)
+/* External triggers of injected group for ADC3 */
+#define ADC3_EXTERNALTRIGINJEC_T4_CC3             ADC1_2_EXTERNALTRIGINJEC_T2_TRGO
+#define ADC3_EXTERNALTRIGINJEC_T8_CC2             ADC1_2_EXTERNALTRIGINJEC_T2_CC1
+#define ADC3_EXTERNALTRIGINJEC_T8_CC4             ADC1_2_EXTERNALTRIGINJEC_T3_CC4
+#define ADC3_EXTERNALTRIGINJEC_T5_TRGO            ADC1_2_EXTERNALTRIGINJEC_T4_TRGO
+#define ADC3_EXTERNALTRIGINJEC_T5_CC4             ADC1_2_EXTERNALTRIGINJEC_EXT_IT15
+#endif /* STM32F103xE || defined STM32F103xG */
+
+/* External triggers of injected group for ADC1&ADC2&ADC3 (if ADCx available) */
+#define ADC1_2_3_EXTERNALTRIGINJEC_T1_TRGO                    0x00000000U
+#define ADC1_2_3_EXTERNALTRIGINJEC_T1_CC4         ((uint32_t)(                                        ADC_CR2_JEXTSEL_0))
+#define ADC1_2_3_JSWSTART                         ((uint32_t)(ADC_CR2_JEXTSEL_2 | ADC_CR2_JEXTSEL_1 | ADC_CR2_JEXTSEL_0))
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+
+/* Exported macro ------------------------------------------------------------*/
+
+/* Private macro -------------------------------------------------------------*/
+
+/** @defgroup ADCEx_Private_Macro ADCEx Private Macro
+  * @{
+  */
+/* Macro reserved for internal HAL driver usage, not intended to be used in   */
+/* code of final user.                                                        */
+
+    
+/**
+  * @brief For devices with 3 ADCs: Defines the external trigger source 
+  *        for regular group according to ADC into common group ADC1&ADC2 or 
+  *        ADC3 (some triggers with same source have different value to
+  *        be programmed into ADC EXTSEL bits of CR2 register).
+  *        For devices with 2 ADCs or less: this macro makes no change.
+  * @param __HANDLE__: ADC handle
+  * @param __EXT_TRIG_CONV__: External trigger selected for regular group.
+  * @retval External trigger to be programmed into EXTSEL bits of CR2 register
+  */
+#if defined (STM32F103xE) || defined (STM32F103xG)
+#define ADC_CFGR_EXTSEL(__HANDLE__, __EXT_TRIG_CONV__)                         \
+ (( (((__HANDLE__)->Instance) == ADC3)                                         \
+  )?                                                                           \
+   ( ( (__EXT_TRIG_CONV__) == ADC_EXTERNALTRIGCONV_T8_TRGO                     \
+     )?                                                                        \
+      (ADC3_EXTERNALTRIG_T8_TRGO)                                              \
+      :                                                                        \
+      (__EXT_TRIG_CONV__)                                                      \
+   )                                                                           \
+   :                                                                           \
+   (__EXT_TRIG_CONV__)                                                         \
+ )
+#else
+#define ADC_CFGR_EXTSEL(__HANDLE__, __EXT_TRIG_CONV__)                         \
+  (__EXT_TRIG_CONV__)
+#endif /* STM32F103xE || STM32F103xG */
+
+/**
+  * @brief For devices with 3 ADCs: Defines the external trigger source 
+  *        for injected group according to ADC into common group ADC1&ADC2 or 
+  *        ADC3 (some triggers with same source have different value to
+  *        be programmed into ADC JEXTSEL bits of CR2 register).
+  *        For devices with 2 ADCs or less: this macro makes no change.
+  * @param __HANDLE__: ADC handle
+  * @param __EXT_TRIG_INJECTCONV__: External trigger selected for injected group.
+  * @retval External trigger to be programmed into JEXTSEL bits of CR2 register
+  */
+#if defined (STM32F103xE) || defined (STM32F103xG)
+#define ADC_CFGR_JEXTSEL(__HANDLE__, __EXT_TRIG_INJECTCONV__)                  \
+ (( (((__HANDLE__)->Instance) == ADC3)                                         \
+  )?                                                                           \
+   ( ( (__EXT_TRIG_INJECTCONV__) == ADC_EXTERNALTRIGINJECCONV_T8_CC4           \
+     )?                                                                        \
+      (ADC3_EXTERNALTRIGINJEC_T8_CC4)                                          \
+      :                                                                        \
+      (__EXT_TRIG_INJECTCONV__)                                                \
+   )                                                                           \
+   :                                                                           \
+   (__EXT_TRIG_INJECTCONV__)                                                   \
+ )
+#else
+#define ADC_CFGR_JEXTSEL(__HANDLE__, __EXT_TRIG_INJECTCONV__)                  \
+   (__EXT_TRIG_INJECTCONV__)
+#endif /* STM32F103xE || STM32F103xG */
+
+
+/**
+  * @brief Verification if multimode is enabled for the selected ADC (multimode ADC master or ADC slave) (applicable for devices with several ADCs)
+  * @param __HANDLE__: ADC handle
+  * @retval Multimode state: RESET if multimode is disabled, other value if multimode is enabled
+  */
+#if defined (STM32F103x6) || defined (STM32F103xB) || defined (STM32F105xC) || defined (STM32F107xC) || defined (STM32F103xE) || defined (STM32F103xG)
+#define ADC_MULTIMODE_IS_ENABLE(__HANDLE__)                                    \
+ (( (((__HANDLE__)->Instance) == ADC1) || (((__HANDLE__)->Instance) == ADC2)   \
+  )?                                                                           \
+   (ADC1->CR1 & ADC_CR1_DUALMOD)                                               \
+   :                                                                           \
+   (RESET)                                                                     \
+ )
+#else
+#define ADC_MULTIMODE_IS_ENABLE(__HANDLE__)                                    \
+  (RESET)
+#endif /* defined STM32F103x6 || defined STM32F103xB || defined STM32F105xC || defined STM32F107xC || defined STM32F103xE || defined STM32F103xG */
+
+/**
+  * @brief Verification of condition for ADC start conversion: ADC must be in non-multimode, or multimode with handle of ADC master (applicable for devices with several ADCs)
+  * @param __HANDLE__: ADC handle
+  * @retval None
+  */
+#if defined (STM32F103x6) || defined (STM32F103xB) || defined (STM32F105xC) || defined (STM32F107xC) || defined (STM32F103xE) || defined (STM32F103xG)
+#define ADC_NONMULTIMODE_OR_MULTIMODEMASTER(__HANDLE__)                        \
+  (( (((__HANDLE__)->Instance) == ADC2)                                        \
+   )?                                                                          \
+    ((ADC1->CR1 & ADC_CR1_DUALMOD) == RESET)                                   \
+    :                                                                          \
+    (!RESET)                                                                   \
+  )
+#else
+#define ADC_NONMULTIMODE_OR_MULTIMODEMASTER(__HANDLE__)                        \
+  (!RESET)
+#endif /* defined STM32F103x6 || defined STM32F103xB || defined STM32F105xC || defined STM32F107xC || defined STM32F103xE || defined STM32F103xG */
+
+/**
+  * @brief Check ADC multimode setting: In case of multimode, check whether ADC master of the selected ADC has feature auto-injection enabled (applicable for devices with several ADCs)
+  * @param __HANDLE__: ADC handle
+  * @retval None
+  */
+#if defined (STM32F103x6) || defined (STM32F103xB) || defined (STM32F105xC) || defined (STM32F107xC) || defined (STM32F103xE) || defined (STM32F103xG)
+#define ADC_MULTIMODE_AUTO_INJECTED(__HANDLE__)                                \
+  (( (((__HANDLE__)->Instance) == ADC1) || (((__HANDLE__)->Instance) == ADC2)  \
+   )?                                                                          \
+    (ADC1->CR1 & ADC_CR1_JAUTO)                                                \
+    :                                                                          \
+    (RESET)                                                                    \
+  )
+#else
+#define ADC_MULTIMODE_AUTO_INJECTED(__HANDLE__)                                \
+  (RESET)
+#endif /* defined STM32F103x6 || defined STM32F103xB || defined STM32F105xC || defined STM32F107xC || defined STM32F103xE || defined STM32F103xG */
+
+#if defined (STM32F103x6) || defined (STM32F103xB) || defined (STM32F105xC) || defined (STM32F107xC) || defined (STM32F103xE) || defined (STM32F103xG)
+/**
+  * @brief Set handle of the other ADC sharing the common multimode settings
+  * @param __HANDLE__: ADC handle
+  * @param __HANDLE_OTHER_ADC__: other ADC handle
+  * @retval None
+  */
+#define ADC_COMMON_ADC_OTHER(__HANDLE__, __HANDLE_OTHER_ADC__)                 \
+  ((__HANDLE_OTHER_ADC__)->Instance = ADC2)
+
+/**
+  * @brief Set handle of the ADC slave associated to the ADC master
+  * On STM32F1 devices, ADC slave is always ADC2 (this can be different
+  * on other STM32 devices)
+  * @param __HANDLE_MASTER__: ADC master handle
+  * @param __HANDLE_SLAVE__: ADC slave handle
+  * @retval None
+  */
+#define ADC_MULTI_SLAVE(__HANDLE_MASTER__, __HANDLE_SLAVE__)                   \
+  ((__HANDLE_SLAVE__)->Instance = ADC2)
+       
+#endif /* defined STM32F103x6 || defined STM32F103xB || defined STM32F105xC || defined STM32F107xC || defined STM32F103xE || defined STM32F103xG */
+
+#define IS_ADC_INJECTED_RANK(CHANNEL) (((CHANNEL) == ADC_INJECTED_RANK_1) || \
+                                       ((CHANNEL) == ADC_INJECTED_RANK_2) || \
+                                       ((CHANNEL) == ADC_INJECTED_RANK_3) || \
+                                       ((CHANNEL) == ADC_INJECTED_RANK_4))
+
+#define IS_ADC_EXTTRIGINJEC_EDGE(EDGE) (((EDGE) == ADC_EXTERNALTRIGINJECCONV_EDGE_NONE)  || \
+                                        ((EDGE) == ADC_EXTERNALTRIGINJECCONV_EDGE_RISING))
+
+/** @defgroup ADCEx_injected_nb_conv_verification ADCEx injected nb conv verification
+  * @{
+  */
+#define IS_ADC_INJECTED_NB_CONV(LENGTH)  (((LENGTH) >= 1U) && ((LENGTH) <= 4U))
+/**
+  * @}
+  */
+
+#if defined (STM32F100xB) || defined (STM32F100xE) || defined (STM32F101x6) || defined (STM32F101xB) || defined (STM32F102x6) || defined (STM32F102xB) || defined (STM32F103x6) || defined (STM32F103xB) || defined (STM32F105xC) || defined (STM32F107xC)
+#define IS_ADC_EXTTRIG(REGTRIG) (((REGTRIG) == ADC_EXTERNALTRIGCONV_T1_CC1)    || \
+                                 ((REGTRIG) == ADC_EXTERNALTRIGCONV_T1_CC2)    || \
+                                 ((REGTRIG) == ADC_EXTERNALTRIGCONV_T2_CC2)    || \
+                                 ((REGTRIG) == ADC_EXTERNALTRIGCONV_T3_TRGO)   || \
+                                 ((REGTRIG) == ADC_EXTERNALTRIGCONV_T4_CC4)    || \
+                                 ((REGTRIG) == ADC_EXTERNALTRIGCONV_EXT_IT11)  || \
+                                 ((REGTRIG) == ADC_SOFTWARE_START))
+#endif
+#if defined (STM32F101xE)
+#define IS_ADC_EXTTRIG(REGTRIG) (((REGTRIG) == ADC_EXTERNALTRIGCONV_T1_CC1)    || \
+                                 ((REGTRIG) == ADC_EXTERNALTRIGCONV_T1_CC2)    || \
+                                 ((REGTRIG) == ADC_EXTERNALTRIGCONV_T2_CC2)    || \
+                                 ((REGTRIG) == ADC_EXTERNALTRIGCONV_T3_TRGO)   || \
+                                 ((REGTRIG) == ADC_EXTERNALTRIGCONV_T4_CC4)    || \
+                                 ((REGTRIG) == ADC_EXTERNALTRIGCONV_EXT_IT11)  || \
+                                 ((REGTRIG) == ADC_EXTERNALTRIGCONV_T8_TRGO)   || \
+                                 ((REGTRIG) == ADC_SOFTWARE_START))
+#endif
+#if defined (STM32F101xG)
+#define IS_ADC_EXTTRIG(REGTRIG) (((REGTRIG) == ADC_EXTERNALTRIGCONV_T1_CC1)    || \
+                                 ((REGTRIG) == ADC_EXTERNALTRIGCONV_T1_CC2)    || \
+                                 ((REGTRIG) == ADC_EXTERNALTRIGCONV_T2_CC2)    || \
+                                 ((REGTRIG) == ADC_EXTERNALTRIGCONV_T3_TRGO)   || \
+                                 ((REGTRIG) == ADC_EXTERNALTRIGCONV_T4_CC4)    || \
+                                 ((REGTRIG) == ADC_EXTERNALTRIGCONV_EXT_IT11)  || \
+                                 ((REGTRIG) == ADC_SOFTWARE_START))
+#endif
+#if defined (STM32F103xE) || defined (STM32F103xG)
+#define IS_ADC_EXTTRIG(REGTRIG) (((REGTRIG) == ADC_EXTERNALTRIGCONV_T1_CC1)    || \
+                                 ((REGTRIG) == ADC_EXTERNALTRIGCONV_T1_CC2)    || \
+                                 ((REGTRIG) == ADC_EXTERNALTRIGCONV_T2_CC2)    || \
+                                 ((REGTRIG) == ADC_EXTERNALTRIGCONV_T3_TRGO)   || \
+                                 ((REGTRIG) == ADC_EXTERNALTRIGCONV_T4_CC4)    || \
+                                 ((REGTRIG) == ADC_EXTERNALTRIGCONV_EXT_IT11)  || \
+                                 ((REGTRIG) == ADC_EXTERNALTRIGCONV_T3_CC1)    || \
+                                 ((REGTRIG) == ADC_EXTERNALTRIGCONV_T2_CC3)    || \
+                                 ((REGTRIG) == ADC_EXTERNALTRIGCONV_T8_CC1)    || \
+                                 ((REGTRIG) == ADC_EXTERNALTRIGCONV_T5_CC1)    || \
+                                 ((REGTRIG) == ADC_EXTERNALTRIGCONV_T5_CC3)    || \
+                                 ((REGTRIG) == ADC_EXTERNALTRIGCONV_T1_CC3)    || \
+                                 ((REGTRIG) == ADC_EXTERNALTRIGCONV_T8_TRGO)   || \
+                                 ((REGTRIG) == ADC_SOFTWARE_START))
+#endif
+
+#if defined (STM32F100xB) || defined (STM32F100xE) || defined (STM32F101x6) || defined (STM32F101xB) || defined (STM32F102x6) || defined (STM32F102xB) || defined (STM32F103x6) || defined (STM32F103xB) || defined (STM32F105xC) || defined (STM32F107xC)
+#define IS_ADC_EXTTRIGINJEC(REGTRIG) (((REGTRIG) == ADC_EXTERNALTRIGINJECCONV_T2_TRGO)  || \
+                                      ((REGTRIG) == ADC_EXTERNALTRIGINJECCONV_T2_CC1)   || \
+                                      ((REGTRIG) == ADC_EXTERNALTRIGINJECCONV_T3_CC4)   || \
+                                      ((REGTRIG) == ADC_EXTERNALTRIGINJECCONV_T4_TRGO)  || \
+                                      ((REGTRIG) == ADC_EXTERNALTRIGINJECCONV_EXT_IT15) || \
+                                      ((REGTRIG) == ADC_EXTERNALTRIGINJECCONV_T1_CC4)   || \
+                                      ((REGTRIG) == ADC_EXTERNALTRIGINJECCONV_T1_TRGO)  || \
+                                      ((REGTRIG) == ADC_INJECTED_SOFTWARE_START))
+#endif
+#if defined (STM32F101xE)
+#define IS_ADC_EXTTRIGINJEC(REGTRIG) (((REGTRIG) == ADC_EXTERNALTRIGINJECCONV_T2_TRGO)  || \
+                                      ((REGTRIG) == ADC_EXTERNALTRIGINJECCONV_T2_CC1)   || \
+                                      ((REGTRIG) == ADC_EXTERNALTRIGINJECCONV_T3_CC4)   || \
+                                      ((REGTRIG) == ADC_EXTERNALTRIGINJECCONV_T4_TRGO)  || \
+                                      ((REGTRIG) == ADC_EXTERNALTRIGINJECCONV_EXT_IT15) || \
+                                      ((REGTRIG) == ADC_EXTERNALTRIGINJECCONV_T1_CC4)   || \
+                                      ((REGTRIG) == ADC_EXTERNALTRIGINJECCONV_T1_TRGO)  || \
+                                      ((REGTRIG) == ADC_EXTERNALTRIGINJECCONV_T8_CC4)   || \
+                                      ((REGTRIG) == ADC_INJECTED_SOFTWARE_START))
+#endif
+#if defined (STM32F101xG)
+#define IS_ADC_EXTTRIGINJEC(REGTRIG) (((REGTRIG) == ADC_EXTERNALTRIGINJECCONV_T2_TRGO)  || \
+                                      ((REGTRIG) == ADC_EXTERNALTRIGINJECCONV_T2_CC1)   || \
+                                      ((REGTRIG) == ADC_EXTERNALTRIGINJECCONV_T3_CC4)   || \
+                                      ((REGTRIG) == ADC_EXTERNALTRIGINJECCONV_T4_TRGO)  || \
+                                      ((REGTRIG) == ADC_EXTERNALTRIGINJECCONV_EXT_IT15) || \
+                                      ((REGTRIG) == ADC_EXTERNALTRIGINJECCONV_T1_CC4)   || \
+                                      ((REGTRIG) == ADC_EXTERNALTRIGINJECCONV_T1_TRGO)  || \
+                                      ((REGTRIG) == ADC_INJECTED_SOFTWARE_START))
+#endif
+#if defined (STM32F103xE) || defined (STM32F103xG)
+#define IS_ADC_EXTTRIGINJEC(REGTRIG) (((REGTRIG) == ADC_EXTERNALTRIGINJECCONV_T2_TRGO)  || \
+                                      ((REGTRIG) == ADC_EXTERNALTRIGINJECCONV_T2_CC1)   || \
+                                      ((REGTRIG) == ADC_EXTERNALTRIGINJECCONV_T3_CC4)   || \
+                                      ((REGTRIG) == ADC_EXTERNALTRIGINJECCONV_T4_TRGO)  || \
+                                      ((REGTRIG) == ADC_EXTERNALTRIGINJECCONV_T5_CC4)   || \
+                                      ((REGTRIG) == ADC_EXTERNALTRIGINJECCONV_EXT_IT15) || \
+                                      ((REGTRIG) == ADC_EXTERNALTRIGINJECCONV_T4_CC3)   || \
+                                      ((REGTRIG) == ADC_EXTERNALTRIGINJECCONV_T8_CC2)   || \
+                                      ((REGTRIG) == ADC_EXTERNALTRIGINJECCONV_T5_TRGO)  || \
+                                      ((REGTRIG) == ADC_EXTERNALTRIGINJECCONV_T5_CC4)   || \
+                                      ((REGTRIG) == ADC_EXTERNALTRIGINJECCONV_T1_CC4)   || \
+                                      ((REGTRIG) == ADC_EXTERNALTRIGINJECCONV_T1_TRGO)  || \
+                                      ((REGTRIG) == ADC_EXTERNALTRIGINJECCONV_T8_CC4)   || \
+                                      ((REGTRIG) == ADC_INJECTED_SOFTWARE_START))
+#endif
+
+#if defined (STM32F103x6) || defined (STM32F103xB) || defined (STM32F105xC) || defined (STM32F107xC) || defined (STM32F103xE) || defined (STM32F103xG)
+#define IS_ADC_MODE(MODE) (((MODE) == ADC_MODE_INDEPENDENT)                || \
+                           ((MODE) == ADC_DUALMODE_REGSIMULT_INJECSIMULT)  || \
+                           ((MODE) == ADC_DUALMODE_REGSIMULT_ALTERTRIG)    || \
+                           ((MODE) == ADC_DUALMODE_INJECSIMULT_INTERLFAST) || \
+                           ((MODE) == ADC_DUALMODE_INJECSIMULT_INTERLSLOW) || \
+                           ((MODE) == ADC_DUALMODE_INJECSIMULT)            || \
+                           ((MODE) == ADC_DUALMODE_REGSIMULT)              || \
+                           ((MODE) == ADC_DUALMODE_INTERLFAST)             || \
+                           ((MODE) == ADC_DUALMODE_INTERLSLOW)             || \
+                           ((MODE) == ADC_DUALMODE_ALTERTRIG) )
+#endif /* defined STM32F103x6 || defined STM32F103xB || defined STM32F105xC || defined STM32F107xC || defined STM32F103xE || defined STM32F103xG */
+
+/**
+  * @}
+  */      
+   
+    
+
+    
+    
+   
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup ADCEx_Exported_Functions
+  * @{
+  */
+
+/* IO operation functions  *****************************************************/
+/** @addtogroup ADCEx_Exported_Functions_Group1
+  * @{
+  */
+
+/* ADC calibration */
+HAL_StatusTypeDef       HAL_ADCEx_Calibration_Start(ADC_HandleTypeDef* hadc);
+
+/* Blocking mode: Polling */
+HAL_StatusTypeDef       HAL_ADCEx_InjectedStart(ADC_HandleTypeDef* hadc);
+HAL_StatusTypeDef       HAL_ADCEx_InjectedStop(ADC_HandleTypeDef* hadc);
+HAL_StatusTypeDef       HAL_ADCEx_InjectedPollForConversion(ADC_HandleTypeDef* hadc, uint32_t Timeout);
+
+/* Non-blocking mode: Interruption */
+HAL_StatusTypeDef       HAL_ADCEx_InjectedStart_IT(ADC_HandleTypeDef* hadc);
+HAL_StatusTypeDef       HAL_ADCEx_InjectedStop_IT(ADC_HandleTypeDef* hadc);
+
+#if defined (STM32F103x6) || defined (STM32F103xB) || defined (STM32F105xC) || defined (STM32F107xC) || defined (STM32F103xE) || defined (STM32F103xG)
+/* ADC multimode */
+HAL_StatusTypeDef       HAL_ADCEx_MultiModeStart_DMA(ADC_HandleTypeDef *hadc, uint32_t *pData, uint32_t Length);
+HAL_StatusTypeDef       HAL_ADCEx_MultiModeStop_DMA(ADC_HandleTypeDef *hadc); 
+#endif /* defined STM32F103x6 || defined STM32F103xB || defined STM32F105xC || defined STM32F107xC || defined STM32F103xE || defined STM32F103xG */
+
+/* ADC retrieve conversion value intended to be used with polling or interruption */
+uint32_t                HAL_ADCEx_InjectedGetValue(ADC_HandleTypeDef* hadc, uint32_t InjectedRank);
+#if defined (STM32F103x6) || defined (STM32F103xB) || defined (STM32F105xC) || defined (STM32F107xC) || defined (STM32F103xE) || defined (STM32F103xG)
+uint32_t                HAL_ADCEx_MultiModeGetValue(ADC_HandleTypeDef *hadc);
+#endif /* defined STM32F103x6 || defined STM32F103xB || defined STM32F105xC || defined STM32F107xC || defined STM32F103xE || defined STM32F103xG */
+
+/* ADC IRQHandler and Callbacks used in non-blocking modes (Interruption) */
+void                    HAL_ADCEx_InjectedConvCpltCallback(ADC_HandleTypeDef* hadc);
+/**
+  * @}
+  */
+
+
+/* Peripheral Control functions ***********************************************/
+/** @addtogroup ADCEx_Exported_Functions_Group2
+  * @{
+  */
+HAL_StatusTypeDef       HAL_ADCEx_InjectedConfigChannel(ADC_HandleTypeDef* hadc,ADC_InjectionConfTypeDef* sConfigInjected);
+#if defined (STM32F103x6) || defined (STM32F103xB) || defined (STM32F105xC) || defined (STM32F107xC) || defined (STM32F103xE) || defined (STM32F103xG)
+HAL_StatusTypeDef       HAL_ADCEx_MultiModeConfigChannel(ADC_HandleTypeDef *hadc, ADC_MultiModeTypeDef *multimode);
+#endif /* defined STM32F103x6 || defined STM32F103xB || defined STM32F105xC || defined STM32F107xC || defined STM32F103xE || defined STM32F103xG */
+/**
+  * @}
+  */
+
+
+/**
+  * @}
+  */
+
+
+/**
+  * @}
+  */ 
+
+/**
+  * @}
+  */
+  
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F1xx_HAL_ADC_EX_H */
+
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_can.h

@@ -0,0 +1,850 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_hal_can.h
+  * @author  MCD Application Team
+  * @brief   Header file of CAN HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef STM32F1xx_HAL_CAN_H
+#define STM32F1xx_HAL_CAN_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_hal_def.h"
+
+/** @addtogroup STM32F1xx_HAL_Driver
+  * @{
+  */
+
+#if defined (CAN1)
+/** @addtogroup CAN
+  * @{
+  */
+
+/* Exported types ------------------------------------------------------------*/
+/** @defgroup CAN_Exported_Types CAN Exported Types
+  * @{
+  */
+/**
+  * @brief  HAL State structures definition
+  */
+typedef enum
+{
+  HAL_CAN_STATE_RESET             = 0x00U,  /*!< CAN not yet initialized or disabled */
+  HAL_CAN_STATE_READY             = 0x01U,  /*!< CAN initialized and ready for use   */
+  HAL_CAN_STATE_LISTENING         = 0x02U,  /*!< CAN receive process is ongoing      */
+  HAL_CAN_STATE_SLEEP_PENDING     = 0x03U,  /*!< CAN sleep request is pending        */
+  HAL_CAN_STATE_SLEEP_ACTIVE      = 0x04U,  /*!< CAN sleep mode is active            */
+  HAL_CAN_STATE_ERROR             = 0x05U   /*!< CAN error state                     */
+
+} HAL_CAN_StateTypeDef;
+
+/**
+  * @brief  CAN init structure definition
+  */
+typedef struct
+{
+  uint32_t Prescaler;                  /*!< Specifies the length of a time quantum.
+                                            This parameter must be a number between Min_Data = 1 and Max_Data = 1024. */
+
+  uint32_t Mode;                       /*!< Specifies the CAN operating mode.
+                                            This parameter can be a value of @ref CAN_operating_mode */
+
+  uint32_t SyncJumpWidth;              /*!< Specifies the maximum number of time quanta the CAN hardware
+                                            is allowed to lengthen or shorten a bit to perform resynchronization.
+                                            This parameter can be a value of @ref CAN_synchronisation_jump_width */
+
+  uint32_t TimeSeg1;                   /*!< Specifies the number of time quanta in Bit Segment 1.
+                                            This parameter can be a value of @ref CAN_time_quantum_in_bit_segment_1 */
+
+  uint32_t TimeSeg2;                   /*!< Specifies the number of time quanta in Bit Segment 2.
+                                            This parameter can be a value of @ref CAN_time_quantum_in_bit_segment_2 */
+
+  FunctionalState TimeTriggeredMode;   /*!< Enable or disable the time triggered communication mode.
+                                            This parameter can be set to ENABLE or DISABLE. */
+
+  FunctionalState AutoBusOff;          /*!< Enable or disable the automatic bus-off management.
+                                            This parameter can be set to ENABLE or DISABLE. */
+
+  FunctionalState AutoWakeUp;          /*!< Enable or disable the automatic wake-up mode.
+                                            This parameter can be set to ENABLE or DISABLE. */
+
+  FunctionalState AutoRetransmission;  /*!< Enable or disable the non-automatic retransmission mode.
+                                            This parameter can be set to ENABLE or DISABLE. */
+
+  FunctionalState ReceiveFifoLocked;   /*!< Enable or disable the Receive FIFO Locked mode.
+                                            This parameter can be set to ENABLE or DISABLE. */
+
+  FunctionalState TransmitFifoPriority;/*!< Enable or disable the transmit FIFO priority.
+                                            This parameter can be set to ENABLE or DISABLE. */
+
+} CAN_InitTypeDef;
+
+/**
+  * @brief  CAN filter configuration structure definition
+  */
+typedef struct
+{
+  uint32_t FilterIdHigh;          /*!< Specifies the filter identification number (MSBs for a 32-bit
+                                       configuration, first one for a 16-bit configuration).
+                                       This parameter must be a number between Min_Data = 0x0000 and Max_Data = 0xFFFF. */
+
+  uint32_t FilterIdLow;           /*!< Specifies the filter identification number (LSBs for a 32-bit
+                                       configuration, second one for a 16-bit configuration).
+                                       This parameter must be a number between Min_Data = 0x0000 and Max_Data = 0xFFFF. */
+
+  uint32_t FilterMaskIdHigh;      /*!< Specifies the filter mask number or identification number,
+                                       according to the mode (MSBs for a 32-bit configuration,
+                                       first one for a 16-bit configuration).
+                                       This parameter must be a number between Min_Data = 0x0000 and Max_Data = 0xFFFF. */
+
+  uint32_t FilterMaskIdLow;       /*!< Specifies the filter mask number or identification number,
+                                       according to the mode (LSBs for a 32-bit configuration,
+                                       second one for a 16-bit configuration).
+                                       This parameter must be a number between Min_Data = 0x0000 and Max_Data = 0xFFFF. */
+
+  uint32_t FilterFIFOAssignment;  /*!< Specifies the FIFO (0 or 1U) which will be assigned to the filter.
+                                       This parameter can be a value of @ref CAN_filter_FIFO */
+
+  uint32_t FilterBank;            /*!< Specifies the filter bank which will be initialized.
+                                       For single CAN instance(14 dedicated filter banks),
+                                       this parameter must be a number between Min_Data = 0 and Max_Data = 13.
+                                       For dual CAN instances(28 filter banks shared),
+                                       this parameter must be a number between Min_Data = 0 and Max_Data = 27. */
+
+  uint32_t FilterMode;            /*!< Specifies the filter mode to be initialized.
+                                       This parameter can be a value of @ref CAN_filter_mode */
+
+  uint32_t FilterScale;           /*!< Specifies the filter scale.
+                                       This parameter can be a value of @ref CAN_filter_scale */
+
+  uint32_t FilterActivation;      /*!< Enable or disable the filter.
+                                       This parameter can be a value of @ref CAN_filter_activation */
+
+  uint32_t SlaveStartFilterBank;  /*!< Select the start filter bank for the slave CAN instance.
+                                       For single CAN instances, this parameter is meaningless.
+                                       For dual CAN instances, all filter banks with lower index are assigned to master
+                                       CAN instance, whereas all filter banks with greater index are assigned to slave
+                                       CAN instance.
+                                       This parameter must be a number between Min_Data = 0 and Max_Data = 27. */
+
+} CAN_FilterTypeDef;
+
+/**
+  * @brief  CAN Tx message header structure definition
+  */
+typedef struct
+{
+  uint32_t StdId;    /*!< Specifies the standard identifier.
+                          This parameter must be a number between Min_Data = 0 and Max_Data = 0x7FF. */
+
+  uint32_t ExtId;    /*!< Specifies the extended identifier.
+                          This parameter must be a number between Min_Data = 0 and Max_Data = 0x1FFFFFFF. */
+
+  uint32_t IDE;      /*!< Specifies the type of identifier for the message that will be transmitted.
+                          This parameter can be a value of @ref CAN_identifier_type */
+
+  uint32_t RTR;      /*!< Specifies the type of frame for the message that will be transmitted.
+                          This parameter can be a value of @ref CAN_remote_transmission_request */
+
+  uint32_t DLC;      /*!< Specifies the length of the frame that will be transmitted.
+                          This parameter must be a number between Min_Data = 0 and Max_Data = 8. */
+
+  FunctionalState TransmitGlobalTime; /*!< Specifies whether the timestamp counter value captured on start
+                          of frame transmission, is sent in DATA6 and DATA7 replacing pData[6] and pData[7].
+                          @note: Time Triggered Communication Mode must be enabled.
+                          @note: DLC must be programmed as 8 bytes, in order these 2 bytes are sent.
+                          This parameter can be set to ENABLE or DISABLE. */
+
+} CAN_TxHeaderTypeDef;
+
+/**
+  * @brief  CAN Rx message header structure definition
+  */
+typedef struct
+{
+  uint32_t StdId;    /*!< Specifies the standard identifier.
+                          This parameter must be a number between Min_Data = 0 and Max_Data = 0x7FF. */
+
+  uint32_t ExtId;    /*!< Specifies the extended identifier.
+                          This parameter must be a number between Min_Data = 0 and Max_Data = 0x1FFFFFFF. */
+
+  uint32_t IDE;      /*!< Specifies the type of identifier for the message that will be transmitted.
+                          This parameter can be a value of @ref CAN_identifier_type */
+
+  uint32_t RTR;      /*!< Specifies the type of frame for the message that will be transmitted.
+                          This parameter can be a value of @ref CAN_remote_transmission_request */
+
+  uint32_t DLC;      /*!< Specifies the length of the frame that will be transmitted.
+                          This parameter must be a number between Min_Data = 0 and Max_Data = 8. */
+
+  uint32_t Timestamp; /*!< Specifies the timestamp counter value captured on start of frame reception.
+                          @note: Time Triggered Communication Mode must be enabled.
+                          This parameter must be a number between Min_Data = 0 and Max_Data = 0xFFFF. */
+
+  uint32_t FilterMatchIndex; /*!< Specifies the index of matching acceptance filter element.
+                          This parameter must be a number between Min_Data = 0 and Max_Data = 0xFF. */
+
+} CAN_RxHeaderTypeDef;
+
+/**
+  * @brief  CAN handle Structure definition
+  */
+typedef struct __CAN_HandleTypeDef
+{
+  CAN_TypeDef                 *Instance;                 /*!< Register base address */
+
+  CAN_InitTypeDef             Init;                      /*!< CAN required parameters */
+
+  __IO HAL_CAN_StateTypeDef   State;                     /*!< CAN communication state */
+
+  __IO uint32_t               ErrorCode;                 /*!< CAN Error code.
+                                                              This parameter can be a value of @ref CAN_Error_Code */
+
+#if USE_HAL_CAN_REGISTER_CALLBACKS == 1
+  void (* TxMailbox0CompleteCallback)(struct __CAN_HandleTypeDef *hcan);/*!< CAN Tx Mailbox 0 complete callback    */
+  void (* TxMailbox1CompleteCallback)(struct __CAN_HandleTypeDef *hcan);/*!< CAN Tx Mailbox 1 complete callback    */
+  void (* TxMailbox2CompleteCallback)(struct __CAN_HandleTypeDef *hcan);/*!< CAN Tx Mailbox 2 complete callback    */
+  void (* TxMailbox0AbortCallback)(struct __CAN_HandleTypeDef *hcan);   /*!< CAN Tx Mailbox 0 abort callback       */
+  void (* TxMailbox1AbortCallback)(struct __CAN_HandleTypeDef *hcan);   /*!< CAN Tx Mailbox 1 abort callback       */
+  void (* TxMailbox2AbortCallback)(struct __CAN_HandleTypeDef *hcan);   /*!< CAN Tx Mailbox 2 abort callback       */
+  void (* RxFifo0MsgPendingCallback)(struct __CAN_HandleTypeDef *hcan); /*!< CAN Rx FIFO 0 msg pending callback    */
+  void (* RxFifo0FullCallback)(struct __CAN_HandleTypeDef *hcan);       /*!< CAN Rx FIFO 0 full callback           */
+  void (* RxFifo1MsgPendingCallback)(struct __CAN_HandleTypeDef *hcan); /*!< CAN Rx FIFO 1 msg pending callback    */
+  void (* RxFifo1FullCallback)(struct __CAN_HandleTypeDef *hcan);       /*!< CAN Rx FIFO 1 full callback           */
+  void (* SleepCallback)(struct __CAN_HandleTypeDef *hcan);             /*!< CAN Sleep callback                    */
+  void (* WakeUpFromRxMsgCallback)(struct __CAN_HandleTypeDef *hcan);   /*!< CAN Wake Up from Rx msg callback      */
+  void (* ErrorCallback)(struct __CAN_HandleTypeDef *hcan);             /*!< CAN Error callback                    */
+
+  void (* MspInitCallback)(struct __CAN_HandleTypeDef *hcan);           /*!< CAN Msp Init callback                 */
+  void (* MspDeInitCallback)(struct __CAN_HandleTypeDef *hcan);         /*!< CAN Msp DeInit callback               */
+
+#endif /* (USE_HAL_CAN_REGISTER_CALLBACKS) */
+} CAN_HandleTypeDef;
+
+#if USE_HAL_CAN_REGISTER_CALLBACKS == 1
+/**
+  * @brief  HAL CAN common Callback ID enumeration definition
+  */
+typedef enum
+{
+  HAL_CAN_TX_MAILBOX0_COMPLETE_CB_ID       = 0x00U,    /*!< CAN Tx Mailbox 0 complete callback ID         */
+  HAL_CAN_TX_MAILBOX1_COMPLETE_CB_ID       = 0x01U,    /*!< CAN Tx Mailbox 1 complete callback ID         */
+  HAL_CAN_TX_MAILBOX2_COMPLETE_CB_ID       = 0x02U,    /*!< CAN Tx Mailbox 2 complete callback ID         */
+  HAL_CAN_TX_MAILBOX0_ABORT_CB_ID          = 0x03U,    /*!< CAN Tx Mailbox 0 abort callback ID            */
+  HAL_CAN_TX_MAILBOX1_ABORT_CB_ID          = 0x04U,    /*!< CAN Tx Mailbox 1 abort callback ID            */
+  HAL_CAN_TX_MAILBOX2_ABORT_CB_ID          = 0x05U,    /*!< CAN Tx Mailbox 2 abort callback ID            */
+  HAL_CAN_RX_FIFO0_MSG_PENDING_CB_ID       = 0x06U,    /*!< CAN Rx FIFO 0 message pending callback ID     */
+  HAL_CAN_RX_FIFO0_FULL_CB_ID              = 0x07U,    /*!< CAN Rx FIFO 0 full callback ID                */
+  HAL_CAN_RX_FIFO1_MSG_PENDING_CB_ID       = 0x08U,    /*!< CAN Rx FIFO 1 message pending callback ID     */
+  HAL_CAN_RX_FIFO1_FULL_CB_ID              = 0x09U,    /*!< CAN Rx FIFO 1 full callback ID                */
+  HAL_CAN_SLEEP_CB_ID                      = 0x0AU,    /*!< CAN Sleep callback ID                         */
+  HAL_CAN_WAKEUP_FROM_RX_MSG_CB_ID         = 0x0BU,    /*!< CAN Wake Up from Rx msg callback ID          */
+  HAL_CAN_ERROR_CB_ID                      = 0x0CU,    /*!< CAN Error callback ID                         */
+
+  HAL_CAN_MSPINIT_CB_ID                    = 0x0DU,    /*!< CAN MspInit callback ID                       */
+  HAL_CAN_MSPDEINIT_CB_ID                  = 0x0EU,    /*!< CAN MspDeInit callback ID                     */
+
+} HAL_CAN_CallbackIDTypeDef;
+
+/**
+  * @brief  HAL CAN Callback pointer definition
+  */
+typedef  void (*pCAN_CallbackTypeDef)(CAN_HandleTypeDef *hcan); /*!< pointer to a CAN callback function   */
+
+#endif /* USE_HAL_CAN_REGISTER_CALLBACKS */
+/**
+  * @}
+  */
+
+/* Exported constants --------------------------------------------------------*/
+
+/** @defgroup CAN_Exported_Constants CAN Exported Constants
+  * @{
+  */
+
+/** @defgroup CAN_Error_Code CAN Error Code
+  * @{
+  */
+#define HAL_CAN_ERROR_NONE            (0x00000000U)  /*!< No error                                             */
+#define HAL_CAN_ERROR_EWG             (0x00000001U)  /*!< Protocol Error Warning                               */
+#define HAL_CAN_ERROR_EPV             (0x00000002U)  /*!< Error Passive                                        */
+#define HAL_CAN_ERROR_BOF             (0x00000004U)  /*!< Bus-off error                                        */
+#define HAL_CAN_ERROR_STF             (0x00000008U)  /*!< Stuff error                                          */
+#define HAL_CAN_ERROR_FOR             (0x00000010U)  /*!< Form error                                           */
+#define HAL_CAN_ERROR_ACK             (0x00000020U)  /*!< Acknowledgment error                                 */
+#define HAL_CAN_ERROR_BR              (0x00000040U)  /*!< Bit recessive error                                  */
+#define HAL_CAN_ERROR_BD              (0x00000080U)  /*!< Bit dominant error                                   */
+#define HAL_CAN_ERROR_CRC             (0x00000100U)  /*!< CRC error                                            */
+#define HAL_CAN_ERROR_RX_FOV0         (0x00000200U)  /*!< Rx FIFO0 overrun error                               */
+#define HAL_CAN_ERROR_RX_FOV1         (0x00000400U)  /*!< Rx FIFO1 overrun error                               */
+#define HAL_CAN_ERROR_TX_ALST0        (0x00000800U)  /*!< TxMailbox 0 transmit failure due to arbitration lost */
+#define HAL_CAN_ERROR_TX_TERR0        (0x00001000U)  /*!< TxMailbox 0 transmit failure due to transmit error    */
+#define HAL_CAN_ERROR_TX_ALST1        (0x00002000U)  /*!< TxMailbox 1 transmit failure due to arbitration lost */
+#define HAL_CAN_ERROR_TX_TERR1        (0x00004000U)  /*!< TxMailbox 1 transmit failure due to transmit error    */
+#define HAL_CAN_ERROR_TX_ALST2        (0x00008000U)  /*!< TxMailbox 2 transmit failure due to arbitration lost */
+#define HAL_CAN_ERROR_TX_TERR2        (0x00010000U)  /*!< TxMailbox 2 transmit failure due to transmit error    */
+#define HAL_CAN_ERROR_TIMEOUT         (0x00020000U)  /*!< Timeout error                                        */
+#define HAL_CAN_ERROR_NOT_INITIALIZED (0x00040000U)  /*!< Peripheral not initialized                           */
+#define HAL_CAN_ERROR_NOT_READY       (0x00080000U)  /*!< Peripheral not ready                                 */
+#define HAL_CAN_ERROR_NOT_STARTED     (0x00100000U)  /*!< Peripheral not started                               */
+#define HAL_CAN_ERROR_PARAM           (0x00200000U)  /*!< Parameter error                                      */
+
+#if USE_HAL_CAN_REGISTER_CALLBACKS == 1
+#define HAL_CAN_ERROR_INVALID_CALLBACK (0x00400000U) /*!< Invalid Callback error                               */
+#endif /* USE_HAL_CAN_REGISTER_CALLBACKS */
+#define HAL_CAN_ERROR_INTERNAL        (0x00800000U)  /*!< Internal error                                       */
+
+/**
+  * @}
+  */
+
+/** @defgroup CAN_InitStatus CAN InitStatus
+  * @{
+  */
+#define CAN_INITSTATUS_FAILED       (0x00000000U)  /*!< CAN initialization failed */
+#define CAN_INITSTATUS_SUCCESS      (0x00000001U)  /*!< CAN initialization OK     */
+/**
+  * @}
+  */
+
+/** @defgroup CAN_operating_mode CAN Operating Mode
+  * @{
+  */
+#define CAN_MODE_NORMAL             (0x00000000U)                              /*!< Normal mode   */
+#define CAN_MODE_LOOPBACK           ((uint32_t)CAN_BTR_LBKM)                   /*!< Loopback mode */
+#define CAN_MODE_SILENT             ((uint32_t)CAN_BTR_SILM)                   /*!< Silent mode   */
+#define CAN_MODE_SILENT_LOOPBACK    ((uint32_t)(CAN_BTR_LBKM | CAN_BTR_SILM))  /*!< Loopback combined with silent mode */
+/**
+  * @}
+  */
+
+
+/** @defgroup CAN_synchronisation_jump_width CAN Synchronization Jump Width
+  * @{
+  */
+#define CAN_SJW_1TQ                 (0x00000000U)              /*!< 1 time quantum */
+#define CAN_SJW_2TQ                 ((uint32_t)CAN_BTR_SJW_0)  /*!< 2 time quantum */
+#define CAN_SJW_3TQ                 ((uint32_t)CAN_BTR_SJW_1)  /*!< 3 time quantum */
+#define CAN_SJW_4TQ                 ((uint32_t)CAN_BTR_SJW)    /*!< 4 time quantum */
+/**
+  * @}
+  */
+
+/** @defgroup CAN_time_quantum_in_bit_segment_1 CAN Time Quantum in Bit Segment 1
+  * @{
+  */
+#define CAN_BS1_1TQ                 (0x00000000U)                                                /*!< 1 time quantum  */
+#define CAN_BS1_2TQ                 ((uint32_t)CAN_BTR_TS1_0)                                    /*!< 2 time quantum  */
+#define CAN_BS1_3TQ                 ((uint32_t)CAN_BTR_TS1_1)                                    /*!< 3 time quantum  */
+#define CAN_BS1_4TQ                 ((uint32_t)(CAN_BTR_TS1_1 | CAN_BTR_TS1_0))                  /*!< 4 time quantum  */
+#define CAN_BS1_5TQ                 ((uint32_t)CAN_BTR_TS1_2)                                    /*!< 5 time quantum  */
+#define CAN_BS1_6TQ                 ((uint32_t)(CAN_BTR_TS1_2 | CAN_BTR_TS1_0))                  /*!< 6 time quantum  */
+#define CAN_BS1_7TQ                 ((uint32_t)(CAN_BTR_TS1_2 | CAN_BTR_TS1_1))                  /*!< 7 time quantum  */
+#define CAN_BS1_8TQ                 ((uint32_t)(CAN_BTR_TS1_2 | CAN_BTR_TS1_1 | CAN_BTR_TS1_0))  /*!< 8 time quantum  */
+#define CAN_BS1_9TQ                 ((uint32_t)CAN_BTR_TS1_3)                                    /*!< 9 time quantum  */
+#define CAN_BS1_10TQ                ((uint32_t)(CAN_BTR_TS1_3 | CAN_BTR_TS1_0))                  /*!< 10 time quantum */
+#define CAN_BS1_11TQ                ((uint32_t)(CAN_BTR_TS1_3 | CAN_BTR_TS1_1))                  /*!< 11 time quantum */
+#define CAN_BS1_12TQ                ((uint32_t)(CAN_BTR_TS1_3 | CAN_BTR_TS1_1 | CAN_BTR_TS1_0))  /*!< 12 time quantum */
+#define CAN_BS1_13TQ                ((uint32_t)(CAN_BTR_TS1_3 | CAN_BTR_TS1_2))                  /*!< 13 time quantum */
+#define CAN_BS1_14TQ                ((uint32_t)(CAN_BTR_TS1_3 | CAN_BTR_TS1_2 | CAN_BTR_TS1_0))  /*!< 14 time quantum */
+#define CAN_BS1_15TQ                ((uint32_t)(CAN_BTR_TS1_3 | CAN_BTR_TS1_2 | CAN_BTR_TS1_1))  /*!< 15 time quantum */
+#define CAN_BS1_16TQ                ((uint32_t)CAN_BTR_TS1) /*!< 16 time quantum */
+/**
+  * @}
+  */
+
+/** @defgroup CAN_time_quantum_in_bit_segment_2 CAN Time Quantum in Bit Segment 2
+  * @{
+  */
+#define CAN_BS2_1TQ                 (0x00000000U)                                /*!< 1 time quantum */
+#define CAN_BS2_2TQ                 ((uint32_t)CAN_BTR_TS2_0)                    /*!< 2 time quantum */
+#define CAN_BS2_3TQ                 ((uint32_t)CAN_BTR_TS2_1)                    /*!< 3 time quantum */
+#define CAN_BS2_4TQ                 ((uint32_t)(CAN_BTR_TS2_1 | CAN_BTR_TS2_0))  /*!< 4 time quantum */
+#define CAN_BS2_5TQ                 ((uint32_t)CAN_BTR_TS2_2)                    /*!< 5 time quantum */
+#define CAN_BS2_6TQ                 ((uint32_t)(CAN_BTR_TS2_2 | CAN_BTR_TS2_0))  /*!< 6 time quantum */
+#define CAN_BS2_7TQ                 ((uint32_t)(CAN_BTR_TS2_2 | CAN_BTR_TS2_1))  /*!< 7 time quantum */
+#define CAN_BS2_8TQ                 ((uint32_t)CAN_BTR_TS2)                      /*!< 8 time quantum */
+/**
+  * @}
+  */
+
+/** @defgroup CAN_filter_mode CAN Filter Mode
+  * @{
+  */
+#define CAN_FILTERMODE_IDMASK       (0x00000000U)  /*!< Identifier mask mode */
+#define CAN_FILTERMODE_IDLIST       (0x00000001U)  /*!< Identifier list mode */
+/**
+  * @}
+  */
+
+/** @defgroup CAN_filter_scale CAN Filter Scale
+  * @{
+  */
+#define CAN_FILTERSCALE_16BIT       (0x00000000U)  /*!< Two 16-bit filters */
+#define CAN_FILTERSCALE_32BIT       (0x00000001U)  /*!< One 32-bit filter  */
+/**
+  * @}
+  */
+
+/** @defgroup CAN_filter_activation CAN Filter Activation
+  * @{
+  */
+#define CAN_FILTER_DISABLE          (0x00000000U)  /*!< Disable filter */
+#define CAN_FILTER_ENABLE           (0x00000001U)  /*!< Enable filter  */
+/**
+  * @}
+  */
+
+/** @defgroup CAN_filter_FIFO CAN Filter FIFO
+  * @{
+  */
+#define CAN_FILTER_FIFO0            (0x00000000U)  /*!< Filter FIFO 0 assignment for filter x */
+#define CAN_FILTER_FIFO1            (0x00000001U)  /*!< Filter FIFO 1 assignment for filter x */
+/**
+  * @}
+  */
+
+/** @defgroup CAN_identifier_type CAN Identifier Type
+  * @{
+  */
+#define CAN_ID_STD                  (0x00000000U)  /*!< Standard Id */
+#define CAN_ID_EXT                  (0x00000004U)  /*!< Extended Id */
+/**
+  * @}
+  */
+
+/** @defgroup CAN_remote_transmission_request CAN Remote Transmission Request
+  * @{
+  */
+#define CAN_RTR_DATA                (0x00000000U)  /*!< Data frame   */
+#define CAN_RTR_REMOTE              (0x00000002U)  /*!< Remote frame */
+/**
+  * @}
+  */
+
+/** @defgroup CAN_receive_FIFO_number CAN Receive FIFO Number
+  * @{
+  */
+#define CAN_RX_FIFO0                (0x00000000U)  /*!< CAN receive FIFO 0 */
+#define CAN_RX_FIFO1                (0x00000001U)  /*!< CAN receive FIFO 1 */
+/**
+  * @}
+  */
+
+/** @defgroup CAN_Tx_Mailboxes CAN Tx Mailboxes
+  * @{
+  */
+#define CAN_TX_MAILBOX0             (0x00000001U)  /*!< Tx Mailbox 0  */
+#define CAN_TX_MAILBOX1             (0x00000002U)  /*!< Tx Mailbox 1  */
+#define CAN_TX_MAILBOX2             (0x00000004U)  /*!< Tx Mailbox 2  */
+/**
+  * @}
+  */
+
+/** @defgroup CAN_flags CAN Flags
+  * @{
+  */
+/* Transmit Flags */
+#define CAN_FLAG_RQCP0              (0x00000500U)  /*!< Request complete MailBox 0 flag   */
+#define CAN_FLAG_TXOK0              (0x00000501U)  /*!< Transmission OK MailBox 0 flag    */
+#define CAN_FLAG_ALST0              (0x00000502U)  /*!< Arbitration Lost MailBox 0 flag   */
+#define CAN_FLAG_TERR0              (0x00000503U)  /*!< Transmission error MailBox 0 flag */
+#define CAN_FLAG_RQCP1              (0x00000508U)  /*!< Request complete MailBox1 flag    */
+#define CAN_FLAG_TXOK1              (0x00000509U)  /*!< Transmission OK MailBox 1 flag    */
+#define CAN_FLAG_ALST1              (0x0000050AU)  /*!< Arbitration Lost MailBox 1 flag   */
+#define CAN_FLAG_TERR1              (0x0000050BU)  /*!< Transmission error MailBox 1 flag */
+#define CAN_FLAG_RQCP2              (0x00000510U)  /*!< Request complete MailBox2 flag    */
+#define CAN_FLAG_TXOK2              (0x00000511U)  /*!< Transmission OK MailBox 2 flag    */
+#define CAN_FLAG_ALST2              (0x00000512U)  /*!< Arbitration Lost MailBox 2 flag   */
+#define CAN_FLAG_TERR2              (0x00000513U)  /*!< Transmission error MailBox 2 flag */
+#define CAN_FLAG_TME0               (0x0000051AU)  /*!< Transmit mailbox 0 empty flag     */
+#define CAN_FLAG_TME1               (0x0000051BU)  /*!< Transmit mailbox 1 empty flag     */
+#define CAN_FLAG_TME2               (0x0000051CU)  /*!< Transmit mailbox 2 empty flag     */
+#define CAN_FLAG_LOW0               (0x0000051DU)  /*!< Lowest priority mailbox 0 flag    */
+#define CAN_FLAG_LOW1               (0x0000051EU)  /*!< Lowest priority mailbox 1 flag    */
+#define CAN_FLAG_LOW2               (0x0000051FU)  /*!< Lowest priority mailbox 2 flag    */
+
+/* Receive Flags */
+#define CAN_FLAG_FF0                (0x00000203U)  /*!< RX FIFO 0 Full flag               */
+#define CAN_FLAG_FOV0               (0x00000204U)  /*!< RX FIFO 0 Overrun flag            */
+#define CAN_FLAG_FF1                (0x00000403U)  /*!< RX FIFO 1 Full flag               */
+#define CAN_FLAG_FOV1               (0x00000404U)  /*!< RX FIFO 1 Overrun flag            */
+
+/* Operating Mode Flags */
+#define CAN_FLAG_INAK               (0x00000100U)  /*!< Initialization acknowledge flag   */
+#define CAN_FLAG_SLAK               (0x00000101U)  /*!< Sleep acknowledge flag            */
+#define CAN_FLAG_ERRI               (0x00000102U)  /*!< Error flag                        */
+#define CAN_FLAG_WKU                (0x00000103U)  /*!< Wake up interrupt flag            */
+#define CAN_FLAG_SLAKI              (0x00000104U)  /*!< Sleep acknowledge interrupt flag  */
+
+/* Error Flags */
+#define CAN_FLAG_EWG                (0x00000300U)  /*!< Error warning flag                */
+#define CAN_FLAG_EPV                (0x00000301U)  /*!< Error passive flag                */
+#define CAN_FLAG_BOF                (0x00000302U)  /*!< Bus-Off flag                      */
+/**
+  * @}
+  */
+
+
+/** @defgroup CAN_Interrupts CAN Interrupts
+  * @{
+  */
+/* Transmit Interrupt */
+#define CAN_IT_TX_MAILBOX_EMPTY     ((uint32_t)CAN_IER_TMEIE)   /*!< Transmit mailbox empty interrupt */
+
+/* Receive Interrupts */
+#define CAN_IT_RX_FIFO0_MSG_PENDING ((uint32_t)CAN_IER_FMPIE0)  /*!< FIFO 0 message pending interrupt */
+#define CAN_IT_RX_FIFO0_FULL        ((uint32_t)CAN_IER_FFIE0)   /*!< FIFO 0 full interrupt            */
+#define CAN_IT_RX_FIFO0_OVERRUN     ((uint32_t)CAN_IER_FOVIE0)  /*!< FIFO 0 overrun interrupt         */
+#define CAN_IT_RX_FIFO1_MSG_PENDING ((uint32_t)CAN_IER_FMPIE1)  /*!< FIFO 1 message pending interrupt */
+#define CAN_IT_RX_FIFO1_FULL        ((uint32_t)CAN_IER_FFIE1)   /*!< FIFO 1 full interrupt            */
+#define CAN_IT_RX_FIFO1_OVERRUN     ((uint32_t)CAN_IER_FOVIE1)  /*!< FIFO 1 overrun interrupt         */
+
+/* Operating Mode Interrupts */
+#define CAN_IT_WAKEUP               ((uint32_t)CAN_IER_WKUIE)   /*!< Wake-up interrupt                */
+#define CAN_IT_SLEEP_ACK            ((uint32_t)CAN_IER_SLKIE)   /*!< Sleep acknowledge interrupt      */
+
+/* Error Interrupts */
+#define CAN_IT_ERROR_WARNING        ((uint32_t)CAN_IER_EWGIE)   /*!< Error warning interrupt          */
+#define CAN_IT_ERROR_PASSIVE        ((uint32_t)CAN_IER_EPVIE)   /*!< Error passive interrupt          */
+#define CAN_IT_BUSOFF               ((uint32_t)CAN_IER_BOFIE)   /*!< Bus-off interrupt                */
+#define CAN_IT_LAST_ERROR_CODE      ((uint32_t)CAN_IER_LECIE)   /*!< Last error code interrupt        */
+#define CAN_IT_ERROR                ((uint32_t)CAN_IER_ERRIE)   /*!< Error Interrupt                  */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Exported macros -----------------------------------------------------------*/
+/** @defgroup CAN_Exported_Macros CAN Exported Macros
+  * @{
+  */
+
+/** @brief  Reset CAN handle state
+  * @param  __HANDLE__ CAN handle.
+  * @retval None
+  */
+#if USE_HAL_CAN_REGISTER_CALLBACKS == 1
+#define __HAL_CAN_RESET_HANDLE_STATE(__HANDLE__) do{                                              \
+                                                     (__HANDLE__)->State = HAL_CAN_STATE_RESET;   \
+                                                     (__HANDLE__)->MspInitCallback = NULL;        \
+                                                     (__HANDLE__)->MspDeInitCallback = NULL;      \
+                                                   } while(0)
+#else
+#define __HAL_CAN_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_CAN_STATE_RESET)
+#endif /*USE_HAL_CAN_REGISTER_CALLBACKS */
+
+/**
+  * @brief  Enable the specified CAN interrupts.
+  * @param  __HANDLE__ CAN handle.
+  * @param  __INTERRUPT__ CAN Interrupt sources to enable.
+  *           This parameter can be any combination of @arg CAN_Interrupts
+  * @retval None
+  */
+#define __HAL_CAN_ENABLE_IT(__HANDLE__, __INTERRUPT__) (((__HANDLE__)->Instance->IER) |= (__INTERRUPT__))
+
+/**
+  * @brief  Disable the specified CAN interrupts.
+  * @param  __HANDLE__ CAN handle.
+  * @param  __INTERRUPT__ CAN Interrupt sources to disable.
+  *           This parameter can be any combination of @arg CAN_Interrupts
+  * @retval None
+  */
+#define __HAL_CAN_DISABLE_IT(__HANDLE__, __INTERRUPT__) (((__HANDLE__)->Instance->IER) &= ~(__INTERRUPT__))
+
+/** @brief  Check if the specified CAN interrupt source is enabled or disabled.
+  * @param  __HANDLE__ specifies the CAN Handle.
+  * @param  __INTERRUPT__ specifies the CAN interrupt source to check.
+  *           This parameter can be a value of @arg CAN_Interrupts
+  * @retval The state of __IT__ (TRUE or FALSE).
+  */
+#define __HAL_CAN_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__) (((__HANDLE__)->Instance->IER) & (__INTERRUPT__))
+
+/** @brief  Check whether the specified CAN flag is set or not.
+  * @param  __HANDLE__ specifies the CAN Handle.
+  * @param  __FLAG__ specifies the flag to check.
+  *         This parameter can be one of @arg CAN_flags
+  * @retval The state of __FLAG__ (TRUE or FALSE).
+  */
+#define __HAL_CAN_GET_FLAG(__HANDLE__, __FLAG__) \
+  ((((__FLAG__) >> 8U) == 5U)? ((((__HANDLE__)->Instance->TSR) & (1U << ((__FLAG__) & CAN_FLAG_MASK))) == (1U << ((__FLAG__) & CAN_FLAG_MASK))): \
+   (((__FLAG__) >> 8U) == 2U)? ((((__HANDLE__)->Instance->RF0R) & (1U << ((__FLAG__) & CAN_FLAG_MASK))) == (1U << ((__FLAG__) & CAN_FLAG_MASK))): \
+   (((__FLAG__) >> 8U) == 4U)? ((((__HANDLE__)->Instance->RF1R) & (1U << ((__FLAG__) & CAN_FLAG_MASK))) == (1U << ((__FLAG__) & CAN_FLAG_MASK))): \
+   (((__FLAG__) >> 8U) == 1U)? ((((__HANDLE__)->Instance->MSR) & (1U << ((__FLAG__) & CAN_FLAG_MASK))) == (1U << ((__FLAG__) & CAN_FLAG_MASK))): \
+   (((__FLAG__) >> 8U) == 3U)? ((((__HANDLE__)->Instance->ESR) & (1U << ((__FLAG__) & CAN_FLAG_MASK))) == (1U << ((__FLAG__) & CAN_FLAG_MASK))): 0U)
+
+/** @brief  Clear the specified CAN pending flag.
+  * @param  __HANDLE__ specifies the CAN Handle.
+  * @param  __FLAG__ specifies the flag to check.
+  *         This parameter can be one of the following values:
+  *            @arg CAN_FLAG_RQCP0: Request complete MailBox 0 Flag
+  *            @arg CAN_FLAG_TXOK0: Transmission OK MailBox 0 Flag
+  *            @arg CAN_FLAG_ALST0: Arbitration Lost MailBox 0 Flag
+  *            @arg CAN_FLAG_TERR0: Transmission error MailBox 0 Flag
+  *            @arg CAN_FLAG_RQCP1: Request complete MailBox 1 Flag
+  *            @arg CAN_FLAG_TXOK1: Transmission OK MailBox 1 Flag
+  *            @arg CAN_FLAG_ALST1: Arbitration Lost MailBox 1 Flag
+  *            @arg CAN_FLAG_TERR1: Transmission error MailBox 1 Flag
+  *            @arg CAN_FLAG_RQCP2: Request complete MailBox 2 Flag
+  *            @arg CAN_FLAG_TXOK2: Transmission OK MailBox 2 Flag
+  *            @arg CAN_FLAG_ALST2: Arbitration Lost MailBox 2 Flag
+  *            @arg CAN_FLAG_TERR2: Transmission error MailBox 2 Flag
+  *            @arg CAN_FLAG_FF0:   RX FIFO 0 Full Flag
+  *            @arg CAN_FLAG_FOV0:  RX FIFO 0 Overrun Flag
+  *            @arg CAN_FLAG_FF1:   RX FIFO 1 Full Flag
+  *            @arg CAN_FLAG_FOV1:  RX FIFO 1 Overrun Flag
+  *            @arg CAN_FLAG_WKUI:  Wake up Interrupt Flag
+  *            @arg CAN_FLAG_SLAKI: Sleep acknowledge Interrupt Flag
+  * @retval None
+  */
+#define __HAL_CAN_CLEAR_FLAG(__HANDLE__, __FLAG__) \
+  ((((__FLAG__) >> 8U) == 5U)? (((__HANDLE__)->Instance->TSR) = (1U << ((__FLAG__) & CAN_FLAG_MASK))): \
+   (((__FLAG__) >> 8U) == 2U)? (((__HANDLE__)->Instance->RF0R) = (1U << ((__FLAG__) & CAN_FLAG_MASK))): \
+   (((__FLAG__) >> 8U) == 4U)? (((__HANDLE__)->Instance->RF1R) = (1U << ((__FLAG__) & CAN_FLAG_MASK))): \
+   (((__FLAG__) >> 8U) == 1U)? (((__HANDLE__)->Instance->MSR) = (1U << ((__FLAG__) & CAN_FLAG_MASK))): 0U)
+
+/**
+ * @}
+ */
+
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup CAN_Exported_Functions CAN Exported Functions
+  * @{
+  */
+
+/** @addtogroup CAN_Exported_Functions_Group1 Initialization and de-initialization functions
+ *  @brief    Initialization and Configuration functions
+ * @{
+ */
+
+/* Initialization and de-initialization functions *****************************/
+HAL_StatusTypeDef HAL_CAN_Init(CAN_HandleTypeDef *hcan);
+HAL_StatusTypeDef HAL_CAN_DeInit(CAN_HandleTypeDef *hcan);
+void HAL_CAN_MspInit(CAN_HandleTypeDef *hcan);
+void HAL_CAN_MspDeInit(CAN_HandleTypeDef *hcan);
+
+#if USE_HAL_CAN_REGISTER_CALLBACKS == 1
+/* Callbacks Register/UnRegister functions  ***********************************/
+HAL_StatusTypeDef HAL_CAN_RegisterCallback(CAN_HandleTypeDef *hcan, HAL_CAN_CallbackIDTypeDef CallbackID, void (* pCallback)(CAN_HandleTypeDef *_hcan));
+HAL_StatusTypeDef HAL_CAN_UnRegisterCallback(CAN_HandleTypeDef *hcan, HAL_CAN_CallbackIDTypeDef CallbackID);
+
+#endif /* (USE_HAL_CAN_REGISTER_CALLBACKS) */
+/**
+ * @}
+ */
+
+/** @addtogroup CAN_Exported_Functions_Group2 Configuration functions
+ *  @brief    Configuration functions
+ * @{
+ */
+
+/* Configuration functions ****************************************************/
+HAL_StatusTypeDef HAL_CAN_ConfigFilter(CAN_HandleTypeDef *hcan, CAN_FilterTypeDef *sFilterConfig);
+
+/**
+ * @}
+ */
+
+/** @addtogroup CAN_Exported_Functions_Group3 Control functions
+ *  @brief    Control functions
+ * @{
+ */
+
+/* Control functions **********************************************************/
+HAL_StatusTypeDef HAL_CAN_Start(CAN_HandleTypeDef *hcan);
+HAL_StatusTypeDef HAL_CAN_Stop(CAN_HandleTypeDef *hcan);
+HAL_StatusTypeDef HAL_CAN_RequestSleep(CAN_HandleTypeDef *hcan);
+HAL_StatusTypeDef HAL_CAN_WakeUp(CAN_HandleTypeDef *hcan);
+uint32_t HAL_CAN_IsSleepActive(CAN_HandleTypeDef *hcan);
+HAL_StatusTypeDef HAL_CAN_AddTxMessage(CAN_HandleTypeDef *hcan, CAN_TxHeaderTypeDef *pHeader, uint8_t aData[], uint32_t *pTxMailbox);
+HAL_StatusTypeDef HAL_CAN_AbortTxRequest(CAN_HandleTypeDef *hcan, uint32_t TxMailboxes);
+uint32_t HAL_CAN_GetTxMailboxesFreeLevel(CAN_HandleTypeDef *hcan);
+uint32_t HAL_CAN_IsTxMessagePending(CAN_HandleTypeDef *hcan, uint32_t TxMailboxes);
+uint32_t HAL_CAN_GetTxTimestamp(CAN_HandleTypeDef *hcan, uint32_t TxMailbox);
+HAL_StatusTypeDef HAL_CAN_GetRxMessage(CAN_HandleTypeDef *hcan, uint32_t RxFifo, CAN_RxHeaderTypeDef *pHeader, uint8_t aData[]);
+uint32_t HAL_CAN_GetRxFifoFillLevel(CAN_HandleTypeDef *hcan, uint32_t RxFifo);
+
+/**
+ * @}
+ */
+
+/** @addtogroup CAN_Exported_Functions_Group4 Interrupts management
+ *  @brief    Interrupts management
+ * @{
+ */
+/* Interrupts management ******************************************************/
+HAL_StatusTypeDef HAL_CAN_ActivateNotification(CAN_HandleTypeDef *hcan, uint32_t ActiveITs);
+HAL_StatusTypeDef HAL_CAN_DeactivateNotification(CAN_HandleTypeDef *hcan, uint32_t InactiveITs);
+void HAL_CAN_IRQHandler(CAN_HandleTypeDef *hcan);
+
+/**
+ * @}
+ */
+
+/** @addtogroup CAN_Exported_Functions_Group5 Callback functions
+ *  @brief    Callback functions
+ * @{
+ */
+/* Callbacks functions ********************************************************/
+
+void HAL_CAN_TxMailbox0CompleteCallback(CAN_HandleTypeDef *hcan);
+void HAL_CAN_TxMailbox1CompleteCallback(CAN_HandleTypeDef *hcan);
+void HAL_CAN_TxMailbox2CompleteCallback(CAN_HandleTypeDef *hcan);
+void HAL_CAN_TxMailbox0AbortCallback(CAN_HandleTypeDef *hcan);
+void HAL_CAN_TxMailbox1AbortCallback(CAN_HandleTypeDef *hcan);
+void HAL_CAN_TxMailbox2AbortCallback(CAN_HandleTypeDef *hcan);
+void HAL_CAN_RxFifo0MsgPendingCallback(CAN_HandleTypeDef *hcan);
+void HAL_CAN_RxFifo0FullCallback(CAN_HandleTypeDef *hcan);
+void HAL_CAN_RxFifo1MsgPendingCallback(CAN_HandleTypeDef *hcan);
+void HAL_CAN_RxFifo1FullCallback(CAN_HandleTypeDef *hcan);
+void HAL_CAN_SleepCallback(CAN_HandleTypeDef *hcan);
+void HAL_CAN_WakeUpFromRxMsgCallback(CAN_HandleTypeDef *hcan);
+void HAL_CAN_ErrorCallback(CAN_HandleTypeDef *hcan);
+
+/**
+ * @}
+ */
+
+/** @addtogroup CAN_Exported_Functions_Group6 Peripheral State and Error functions
+ *  @brief   CAN Peripheral State functions
+ * @{
+ */
+/* Peripheral State and Error functions ***************************************/
+HAL_CAN_StateTypeDef HAL_CAN_GetState(CAN_HandleTypeDef *hcan);
+uint32_t HAL_CAN_GetError(CAN_HandleTypeDef *hcan);
+HAL_StatusTypeDef HAL_CAN_ResetError(CAN_HandleTypeDef *hcan);
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/* Private types -------------------------------------------------------------*/
+/** @defgroup CAN_Private_Types CAN Private Types
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/* Private variables ---------------------------------------------------------*/
+/** @defgroup CAN_Private_Variables CAN Private Variables
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/* Private constants ---------------------------------------------------------*/
+/** @defgroup CAN_Private_Constants CAN Private Constants
+  * @{
+  */
+#define CAN_FLAG_MASK  (0x000000FFU)
+/**
+  * @}
+  */
+
+/* Private Macros -----------------------------------------------------------*/
+/** @defgroup CAN_Private_Macros CAN Private Macros
+  * @{
+  */
+
+#define IS_CAN_MODE(MODE) (((MODE) == CAN_MODE_NORMAL) || \
+                           ((MODE) == CAN_MODE_LOOPBACK)|| \
+                           ((MODE) == CAN_MODE_SILENT) || \
+                           ((MODE) == CAN_MODE_SILENT_LOOPBACK))
+#define IS_CAN_SJW(SJW) (((SJW) == CAN_SJW_1TQ) || ((SJW) == CAN_SJW_2TQ) || \
+                         ((SJW) == CAN_SJW_3TQ) || ((SJW) == CAN_SJW_4TQ))
+#define IS_CAN_BS1(BS1) (((BS1) == CAN_BS1_1TQ) || ((BS1) == CAN_BS1_2TQ) || \
+                         ((BS1) == CAN_BS1_3TQ) || ((BS1) == CAN_BS1_4TQ) || \
+                         ((BS1) == CAN_BS1_5TQ) || ((BS1) == CAN_BS1_6TQ) || \
+                         ((BS1) == CAN_BS1_7TQ) || ((BS1) == CAN_BS1_8TQ) || \
+                         ((BS1) == CAN_BS1_9TQ) || ((BS1) == CAN_BS1_10TQ)|| \
+                         ((BS1) == CAN_BS1_11TQ)|| ((BS1) == CAN_BS1_12TQ)|| \
+                         ((BS1) == CAN_BS1_13TQ)|| ((BS1) == CAN_BS1_14TQ)|| \
+                         ((BS1) == CAN_BS1_15TQ)|| ((BS1) == CAN_BS1_16TQ))
+#define IS_CAN_BS2(BS2) (((BS2) == CAN_BS2_1TQ) || ((BS2) == CAN_BS2_2TQ) || \
+                         ((BS2) == CAN_BS2_3TQ) || ((BS2) == CAN_BS2_4TQ) || \
+                         ((BS2) == CAN_BS2_5TQ) || ((BS2) == CAN_BS2_6TQ) || \
+                         ((BS2) == CAN_BS2_7TQ) || ((BS2) == CAN_BS2_8TQ))
+#define IS_CAN_PRESCALER(PRESCALER) (((PRESCALER) >= 1U) && ((PRESCALER) <= 1024U))
+#define IS_CAN_FILTER_ID_HALFWORD(HALFWORD) ((HALFWORD) <= 0xFFFFU)
+#if   defined(CAN2)
+#define IS_CAN_FILTER_BANK_DUAL(BANK) ((BANK) <= 27U)
+#endif
+#define IS_CAN_FILTER_BANK_SINGLE(BANK) ((BANK) <= 13U)
+#define IS_CAN_FILTER_MODE(MODE) (((MODE) == CAN_FILTERMODE_IDMASK) || \
+                                  ((MODE) == CAN_FILTERMODE_IDLIST))
+#define IS_CAN_FILTER_SCALE(SCALE) (((SCALE) == CAN_FILTERSCALE_16BIT) || \
+                                    ((SCALE) == CAN_FILTERSCALE_32BIT))
+#define IS_CAN_FILTER_ACTIVATION(ACTIVATION) (((ACTIVATION) == CAN_FILTER_DISABLE) || \
+                                              ((ACTIVATION) == CAN_FILTER_ENABLE))
+#define IS_CAN_FILTER_FIFO(FIFO) (((FIFO) == CAN_FILTER_FIFO0) || \
+                                  ((FIFO) == CAN_FILTER_FIFO1))
+#define IS_CAN_TX_MAILBOX(TRANSMITMAILBOX) (((TRANSMITMAILBOX) == CAN_TX_MAILBOX0 ) || \
+                                            ((TRANSMITMAILBOX) == CAN_TX_MAILBOX1 ) || \
+                                            ((TRANSMITMAILBOX) == CAN_TX_MAILBOX2 ))
+#define IS_CAN_TX_MAILBOX_LIST(TRANSMITMAILBOX) ((TRANSMITMAILBOX) <= (CAN_TX_MAILBOX0 | CAN_TX_MAILBOX1 | CAN_TX_MAILBOX2))
+#define IS_CAN_STDID(STDID)   ((STDID) <= 0x7FFU)
+#define IS_CAN_EXTID(EXTID)   ((EXTID) <= 0x1FFFFFFFU)
+#define IS_CAN_DLC(DLC)       ((DLC) <= 8U)
+#define IS_CAN_IDTYPE(IDTYPE)  (((IDTYPE) == CAN_ID_STD) || \
+                                ((IDTYPE) == CAN_ID_EXT))
+#define IS_CAN_RTR(RTR) (((RTR) == CAN_RTR_DATA) || ((RTR) == CAN_RTR_REMOTE))
+#define IS_CAN_RX_FIFO(FIFO) (((FIFO) == CAN_RX_FIFO0) || ((FIFO) == CAN_RX_FIFO1))
+#define IS_CAN_IT(IT) ((IT) <= (CAN_IT_TX_MAILBOX_EMPTY     | CAN_IT_RX_FIFO0_MSG_PENDING      | \
+                                CAN_IT_RX_FIFO0_FULL        | CAN_IT_RX_FIFO0_OVERRUN          | \
+                                CAN_IT_RX_FIFO1_MSG_PENDING | CAN_IT_RX_FIFO1_FULL             | \
+                                CAN_IT_RX_FIFO1_OVERRUN     | CAN_IT_WAKEUP                    | \
+                                CAN_IT_SLEEP_ACK            | CAN_IT_ERROR_WARNING             | \
+                                CAN_IT_ERROR_PASSIVE        | CAN_IT_BUSOFF                    | \
+                                CAN_IT_LAST_ERROR_CODE      | CAN_IT_ERROR))
+
+/**
+  * @}
+  */
+/* End of private macros -----------------------------------------------------*/
+
+/**
+  * @}
+  */
+
+
+#endif /* CAN1 */
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* STM32F1xx_HAL_CAN_H */
+
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_cec.h

@@ -0,0 +1,552 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_hal_cec.h
+  * @author  MCD Application Team
+  * @brief   Header file of CEC HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************  
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F1xx_HAL_CEC_H
+#define __STM32F1xx_HAL_CEC_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_hal_def.h"
+
+#if defined (CEC)
+
+/** @addtogroup STM32F1xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup CEC
+  * @{
+  */
+ 
+/* Exported types ------------------------------------------------------------*/ 
+/** @defgroup CEC_Exported_Types CEC Exported Types
+  * @{
+  */
+/** 
+  * @brief CEC Init Structure definition  
+  */ 
+typedef struct
+{
+  uint32_t TimingErrorFree; /*!< Configures the CEC Bit Timing Error Mode. 
+                                 This parameter can be a value of @ref CEC_BitTimingErrorMode */
+  uint32_t PeriodErrorFree; /*!< Configures the CEC Bit Period Error Mode. 
+                                 This parameter can be a value of @ref CEC_BitPeriodErrorMode */
+  uint16_t  OwnAddress;     /*!< Own addresses configuration
+                                 This parameter can be a value of @ref CEC_OWN_ADDRESS */
+  uint8_t  *RxBuffer;       /*!< CEC Rx buffer pointeur */
+}CEC_InitTypeDef;
+
+/** 
+  * @brief HAL CEC State structures definition 
+  * @note  HAL CEC State value is a combination of 2 different substates: gState and RxState.
+  *        - gState contains CEC state information related to global Handle management 
+  *          and also information related to Tx operations.
+  *          gState value coding follow below described bitmap :
+  *          b7 (not used)
+  *             x  : Should be set to 0
+  *          b6  Error information 
+  *             0  : No Error
+  *             1  : Error
+  *          b5     IP initilisation status
+  *             0  : Reset (IP not initialized)
+  *             1  : Init done (IP initialized. HAL CEC Init function already called)
+  *          b4-b3  (not used)
+  *             xx : Should be set to 00
+  *          b2     Intrinsic process state
+  *             0  : Ready
+  *             1  : Busy (IP busy with some configuration or internal operations)
+  *          b1     (not used)
+  *             x  : Should be set to 0
+  *          b0     Tx state
+  *             0  : Ready (no Tx operation ongoing)
+  *             1  : Busy (Tx operation ongoing)
+  *        - RxState contains information related to Rx operations.
+  *          RxState value coding follow below described bitmap :
+  *          b7-b6  (not used)
+  *             xx : Should be set to 00
+  *          b5     IP initilisation status
+  *             0  : Reset (IP not initialized)
+  *             1  : Init done (IP initialized)
+  *          b4-b2  (not used)
+  *            xxx : Should be set to 000
+  *          b1     Rx state
+  *             0  : Ready (no Rx operation ongoing)
+  *             1  : Busy (Rx operation ongoing)
+  *          b0     (not used)
+  *             x  : Should be set to 0.  
+  */ 
+typedef enum
+{
+  HAL_CEC_STATE_RESET             = 0x00U,    /*!< Peripheral is not yet Initialized 
+                                                   Value is allowed for gState and RxState             */
+  HAL_CEC_STATE_READY             = 0x20U,    /*!< Peripheral Initialized and ready for use
+                                                   Value is allowed for gState and RxState             */
+  HAL_CEC_STATE_BUSY              = 0x24U,    /*!< an internal process is ongoing
+                                                   Value is allowed for gState only                    */
+  HAL_CEC_STATE_BUSY_RX           = 0x22U,    /*!< Data Reception process is ongoing
+                                                   Value is allowed for RxState only                   */
+  HAL_CEC_STATE_BUSY_TX           = 0x21U,    /*!< Data Transmission process is ongoing 
+                                                   Value is allowed for gState only                    */
+  HAL_CEC_STATE_BUSY_RX_TX        = 0x23U,    /*!< an internal process is ongoing
+                                                   Value is allowed for gState only                    */
+  HAL_CEC_STATE_ERROR             = 0x60U     /*!< Error Value is allowed for gState only              */
+}HAL_CEC_StateTypeDef;
+
+/** 
+  * @brief  CEC handle Structure definition  
+  */  
+typedef struct __CEC_HandleTypeDef
+{
+  CEC_TypeDef             *Instance;      /*!< CEC registers base address */
+  
+  CEC_InitTypeDef         Init;           /*!< CEC communication parameters */
+  
+  uint8_t                 *pTxBuffPtr;    /*!< Pointer to CEC Tx transfer Buffer */
+  
+  uint16_t                TxXferCount;    /*!< CEC Tx Transfer Counter */
+  
+  uint16_t                RxXferSize;     /*!< CEC Rx Transfer size, 0: header received only */
+  
+  HAL_LockTypeDef         Lock;           /*!< Locking object */
+
+  HAL_CEC_StateTypeDef    gState;         /*!< CEC state information related to global Handle management 
+                                               and also related to Tx operations.
+                                               This parameter can be a value of @ref HAL_CEC_StateTypeDef */
+  
+  HAL_CEC_StateTypeDef    RxState;        /*!< CEC state information related to Rx operations.
+                                               This parameter can be a value of @ref HAL_CEC_StateTypeDef */
+  
+  uint32_t                ErrorCode;      /*!< For errors handling purposes, copy of ISR register 
+                                               in case error is reported */  
+
+#if (USE_HAL_CEC_REGISTER_CALLBACKS == 1)
+  void  (* TxCpltCallback) ( struct __CEC_HandleTypeDef * hcec);                            /*!< CEC Tx Transfer completed callback */
+  void  (* RxCpltCallback) ( struct __CEC_HandleTypeDef * hcec, uint32_t RxFrameSize);      /*!< CEC Rx Transfer completed callback */
+  void  (* ErrorCallback)  ( struct __CEC_HandleTypeDef * hcec);                            /*!< CEC error callback */
+
+  void  (* MspInitCallback)        ( struct __CEC_HandleTypeDef * hcec);    /*!< CEC Msp Init callback              */
+  void  (* MspDeInitCallback)      ( struct __CEC_HandleTypeDef * hcec);    /*!< CEC Msp DeInit callback            */
+
+#endif /* (USE_HAL_CEC_REGISTER_CALLBACKS) */											   
+}CEC_HandleTypeDef;
+
+#if (USE_HAL_CEC_REGISTER_CALLBACKS == 1)
+/**
+  * @brief  HAL CEC Callback ID enumeration definition
+  */
+typedef enum
+{
+  HAL_CEC_TX_CPLT_CB_ID      = 0x00U,    /*!< CEC Tx Transfer completed callback ID  */
+  HAL_CEC_RX_CPLT_CB_ID      = 0x01U,    /*!< CEC Rx Transfer completed callback ID  */
+  HAL_CEC_ERROR_CB_ID        = 0x02U,    /*!< CEC error callback  ID                 */
+  HAL_CEC_MSPINIT_CB_ID      = 0x03U,    /*!< CEC Msp Init callback ID               */
+  HAL_CEC_MSPDEINIT_CB_ID    = 0x04U     /*!< CEC Msp DeInit callback ID             */
+}HAL_CEC_CallbackIDTypeDef;
+
+/**
+  * @brief  HAL CEC Callback pointer definition
+  */
+typedef  void (*pCEC_CallbackTypeDef)(CEC_HandleTypeDef * hcec); /*!< pointer to an CEC callback function */
+typedef  void (*pCEC_RxCallbackTypeDef)(CEC_HandleTypeDef * hcec, uint32_t RxFrameSize); /*!< pointer to an Rx Transfer completed callback function */
+#endif /* USE_HAL_CEC_REGISTER_CALLBACKS */
+/**
+  * @}
+  */
+
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup CEC_Exported_Constants CEC Exported Constants
+  * @{
+  */
+
+/** @defgroup CEC_Error_Code CEC Error Code
+  * @{
+  */
+#define HAL_CEC_ERROR_NONE   0x00000000U    /*!< no error */
+#define HAL_CEC_ERROR_BTE    CEC_ESR_BTE    /*!< Bit Timing Error */
+#define HAL_CEC_ERROR_BPE    CEC_ESR_BPE    /*!< Bit Period Error */
+#define HAL_CEC_ERROR_RBTFE  CEC_ESR_RBTFE  /*!< Rx Block Transfer Finished Error */
+#define HAL_CEC_ERROR_SBE    CEC_ESR_SBE    /*!< Start Bit Error */
+#define HAL_CEC_ERROR_ACKE   CEC_ESR_ACKE   /*!< Block Acknowledge Error */
+#define HAL_CEC_ERROR_LINE   CEC_ESR_LINE   /*!< Line Error */
+#define HAL_CEC_ERROR_TBTFE  CEC_ESR_TBTFE  /*!< Tx Block Transfer Finished Error */
+#if (USE_HAL_CEC_REGISTER_CALLBACKS == 1)
+#define  HAL_CEC_ERROR_INVALID_CALLBACK ((uint32_t)0x00000080U) /*!< Invalid Callback Error  */
+#endif /* USE_HAL_CEC_REGISTER_CALLBACKS */
+/**
+  * @}
+  */
+
+/** @defgroup CEC_BitTimingErrorMode Bit Timing Error Mode
+  * @{
+  */ 
+#define CEC_BIT_TIMING_ERROR_MODE_STANDARD  0x00000000U      /*!< Bit timing error Standard Mode */
+#define CEC_BIT_TIMING_ERROR_MODE_ERRORFREE CEC_CFGR_BTEM    /*!< Bit timing error Free Mode */
+/**
+  * @}
+  */
+
+/** @defgroup CEC_BitPeriodErrorMode Bit Period Error Mode
+  * @{
+  */ 
+#define CEC_BIT_PERIOD_ERROR_MODE_STANDARD 0x00000000U      /*!< Bit period error Standard Mode */
+#define CEC_BIT_PERIOD_ERROR_MODE_FLEXIBLE CEC_CFGR_BPEM    /*!< Bit period error Flexible Mode */
+/**
+  * @}
+  */ 
+  
+/** @defgroup CEC_Initiator_Position   CEC Initiator logical address position in message header     
+  * @{
+  */
+#define CEC_INITIATOR_LSB_POS                  4U
+/**
+  * @}
+  */
+
+/** @defgroup CEC_OWN_ADDRESS   CEC Own Address    
+  * @{
+  */
+#define CEC_OWN_ADDRESS_NONE            CEC_OWN_ADDRESS_0    /* Reset value */
+#define CEC_OWN_ADDRESS_0              ((uint16_t)0x0000U)   /* Logical Address 0 */
+#define CEC_OWN_ADDRESS_1              ((uint16_t)0x0001U)   /* Logical Address 1 */
+#define CEC_OWN_ADDRESS_2              ((uint16_t)0x0002U)   /* Logical Address 2 */
+#define CEC_OWN_ADDRESS_3              ((uint16_t)0x0003U)   /* Logical Address 3 */
+#define CEC_OWN_ADDRESS_4              ((uint16_t)0x0004U)   /* Logical Address 4 */
+#define CEC_OWN_ADDRESS_5              ((uint16_t)0x0005U)   /* Logical Address 5 */
+#define CEC_OWN_ADDRESS_6              ((uint16_t)0x0006U)   /* Logical Address 6 */
+#define CEC_OWN_ADDRESS_7              ((uint16_t)0x0007U)   /* Logical Address 7 */
+#define CEC_OWN_ADDRESS_8              ((uint16_t)0x0008U)   /* Logical Address 8 */
+#define CEC_OWN_ADDRESS_9              ((uint16_t)0x0009U)   /* Logical Address 9 */
+#define CEC_OWN_ADDRESS_10             ((uint16_t)0x000AU)   /* Logical Address 10 */
+#define CEC_OWN_ADDRESS_11             ((uint16_t)0x000BU)   /* Logical Address 11 */
+#define CEC_OWN_ADDRESS_12             ((uint16_t)0x000CU)   /* Logical Address 12 */
+#define CEC_OWN_ADDRESS_13             ((uint16_t)0x000DU)   /* Logical Address 13 */
+#define CEC_OWN_ADDRESS_14             ((uint16_t)0x000EU)   /* Logical Address 14 */
+#define CEC_OWN_ADDRESS_15             ((uint16_t)0x000FU)   /* Logical Address 15 */
+/**
+  * @}
+  */
+
+/** @defgroup CEC_Interrupts_Definitions  Interrupts definition
+  * @{
+  */
+#define CEC_IT_IE CEC_CFGR_IE
+/**
+  * @}
+  */
+
+/** @defgroup CEC_Flags_Definitions  Flags definition
+  * @{
+  */
+#define CEC_FLAG_TSOM  CEC_CSR_TSOM
+#define CEC_FLAG_TEOM  CEC_CSR_TEOM
+#define CEC_FLAG_TERR  CEC_CSR_TERR
+#define CEC_FLAG_TBTRF CEC_CSR_TBTRF
+#define CEC_FLAG_RSOM  CEC_CSR_RSOM
+#define CEC_FLAG_REOM  CEC_CSR_REOM
+#define CEC_FLAG_RERR  CEC_CSR_RERR
+#define CEC_FLAG_RBTF  CEC_CSR_RBTF
+/**
+  * @}
+  */
+  
+/**
+  * @}
+  */  
+  
+/* Exported macros -----------------------------------------------------------*/
+/** @defgroup CEC_Exported_Macros CEC Exported Macros
+  * @{
+  */
+
+/** @brief  Reset CEC handle gstate & RxState
+  * @param  __HANDLE__: CEC handle.
+  * @retval None
+  */
+#if (USE_HAL_CEC_REGISTER_CALLBACKS == 1)
+#define __HAL_CEC_RESET_HANDLE_STATE(__HANDLE__) do{                                                   \
+                                                       (__HANDLE__)->gState = HAL_CEC_STATE_RESET;     \
+                                                       (__HANDLE__)->RxState = HAL_CEC_STATE_RESET;    \
+                                                       (__HANDLE__)->MspInitCallback = NULL;           \
+                                                       (__HANDLE__)->MspDeInitCallback = NULL;         \
+                                                     } while(0)
+#else  
+#define __HAL_CEC_RESET_HANDLE_STATE(__HANDLE__) do{                                                   \
+                                                       (__HANDLE__)->gState = HAL_CEC_STATE_RESET;     \
+                                                       (__HANDLE__)->RxState = HAL_CEC_STATE_RESET;    \
+                                                     } while(0)
+#endif /* USE_HAL_CEC_REGISTER_CALLBACKS */
+
+/** @brief  Checks whether or not the specified CEC interrupt flag is set.
+  * @param  __HANDLE__: specifies the CEC Handle.
+  * @param  __FLAG__: specifies the flag to check.
+  *     @arg CEC_FLAG_TERR: Tx Error
+  *     @arg CEC_FLAG_TBTRF:Tx Block Transfer Finished
+  *     @arg CEC_FLAG_RERR: Rx Error
+  *     @arg CEC_FLAG_RBTF: Rx Block Transfer Finished
+  * @retval ITStatus
+  */
+#define __HAL_CEC_GET_FLAG(__HANDLE__, __FLAG__) READ_BIT((__HANDLE__)->Instance->CSR,(__FLAG__)) 
+
+/** @brief  Clears the CEC's pending flags.
+  * @param  __HANDLE__: specifies the CEC Handle.
+  * @param  __FLAG__: specifies the flag to clear.
+  *   This parameter can be any combination of the following values:
+  *     @arg CEC_CSR_TERR: Tx Error
+  *     @arg CEC_FLAG_TBTRF: Tx Block Transfer Finished
+  *     @arg CEC_CSR_RERR: Rx Error
+  *     @arg CEC_CSR_RBTF: Rx Block Transfer Finished
+  * @retval none  
+  */
+#define __HAL_CEC_CLEAR_FLAG(__HANDLE__, __FLAG__)                                                                   \
+                          do {                                                                                       \
+                            uint32_t tmp = 0x0U;                                                                     \
+                            tmp = (__HANDLE__)->Instance->CSR & 0x00000002U;                                         \
+                            (__HANDLE__)->Instance->CSR &= (uint32_t)(((~(uint32_t)(__FLAG__)) & 0xFFFFFFFCU) | tmp);\
+                          } while(0U)
+
+/** @brief  Enables the specified CEC interrupt.
+  * @param  __HANDLE__: specifies the CEC Handle.
+  * @param  __INTERRUPT__: specifies the CEC interrupt to enable.
+  *          This parameter can be:
+  *            @arg CEC_IT_IE         : Interrupt Enable.
+  * @retval none
+  */
+#define __HAL_CEC_ENABLE_IT(__HANDLE__, __INTERRUPT__) SET_BIT((__HANDLE__)->Instance->CFGR, (__INTERRUPT__))
+
+/** @brief  Disables the specified CEC interrupt.
+  * @param  __HANDLE__: specifies the CEC Handle.
+  * @param  __INTERRUPT__: specifies the CEC interrupt to disable.
+  *          This parameter can be:
+  *            @arg CEC_IT_IE         : Interrupt Enable
+  * @retval none
+  */   
+#define __HAL_CEC_DISABLE_IT(__HANDLE__, __INTERRUPT__) CLEAR_BIT((__HANDLE__)->Instance->CFGR, (__INTERRUPT__))
+
+/** @brief  Checks whether or not the specified CEC interrupt is enabled.
+  * @param  __HANDLE__: specifies the CEC Handle.
+  * @param  __INTERRUPT__: specifies the CEC interrupt to check.
+  *          This parameter can be:
+  *            @arg CEC_IT_IE         : Interrupt Enable
+  * @retval FlagStatus  
+  */
+#define __HAL_CEC_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__) READ_BIT((__HANDLE__)->Instance->CFGR, (__INTERRUPT__))
+
+/** @brief  Enables the CEC device
+  * @param  __HANDLE__: specifies the CEC Handle.               
+  * @retval none 
+  */
+#define __HAL_CEC_ENABLE(__HANDLE__) SET_BIT((__HANDLE__)->Instance->CFGR, CEC_CFGR_PE)
+
+/** @brief  Disables the CEC device
+  * @param  __HANDLE__: specifies the CEC Handle.               
+  * @retval none 
+  */
+#define __HAL_CEC_DISABLE(__HANDLE__) CLEAR_BIT((__HANDLE__)->Instance->CFGR, CEC_CFGR_PE)
+
+/** @brief  Set Transmission Start flag
+  * @param  __HANDLE__: specifies the CEC Handle.               
+  * @retval none 
+  */
+#define __HAL_CEC_FIRST_BYTE_TX_SET(__HANDLE__) SET_BIT((__HANDLE__)->Instance->CSR, CEC_CSR_TSOM)
+
+/** @brief  Set Transmission End flag
+  * @param  __HANDLE__: specifies the CEC Handle.               
+  * @retval none
+  */
+#define __HAL_CEC_LAST_BYTE_TX_SET(__HANDLE__) SET_BIT((__HANDLE__)->Instance->CSR, CEC_CSR_TEOM)
+
+/** @brief  Get Transmission Start flag
+  * @param  __HANDLE__: specifies the CEC Handle.               
+  * @retval FlagStatus 
+  */
+#define __HAL_CEC_GET_TRANSMISSION_START_FLAG(__HANDLE__) READ_BIT((__HANDLE__)->Instance->CSR, CEC_CSR_TSOM)
+
+/** @brief  Get Transmission End flag
+  * @param  __HANDLE__: specifies the CEC Handle.               
+  * @retval FlagStatus 
+  */
+#define __HAL_CEC_GET_TRANSMISSION_END_FLAG(__HANDLE__) READ_BIT((__HANDLE__)->Instance->CSR, CEC_CSR_TEOM)
+
+/** @brief  Clear OAR register
+  * @param  __HANDLE__: specifies the CEC Handle.               
+  * @retval none 
+  */
+#define __HAL_CEC_CLEAR_OAR(__HANDLE__)   CLEAR_BIT((__HANDLE__)->Instance->OAR, CEC_OAR_OA)
+
+/** @brief  Set OAR register
+  * @param  __HANDLE__: specifies the CEC Handle. 
+  * @param  __ADDRESS__: Own Address value.
+  * @retval none 
+  */
+#define __HAL_CEC_SET_OAR(__HANDLE__,__ADDRESS__) MODIFY_REG((__HANDLE__)->Instance->OAR, CEC_OAR_OA, (__ADDRESS__));
+
+/**
+  * @}
+  */
+
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup CEC_Exported_Functions CEC Exported Functions
+  * @{
+  */
+
+/** @addtogroup CEC_Exported_Functions_Group1 Initialization and de-initialization functions
+  *  @brief    Initialization and Configuration functions 
+  * @{
+  */
+/* Initialization and de-initialization functions  ****************************/
+HAL_StatusTypeDef HAL_CEC_Init(CEC_HandleTypeDef *hcec);
+HAL_StatusTypeDef HAL_CEC_DeInit(CEC_HandleTypeDef *hcec);
+HAL_StatusTypeDef HAL_CEC_SetDeviceAddress(CEC_HandleTypeDef *hcec, uint16_t CEC_OwnAddress);
+void HAL_CEC_MspInit(CEC_HandleTypeDef *hcec);
+void HAL_CEC_MspDeInit(CEC_HandleTypeDef *hcec);
+#if (USE_HAL_CEC_REGISTER_CALLBACKS == 1)
+HAL_StatusTypeDef HAL_CEC_RegisterCallback(CEC_HandleTypeDef *hcec, HAL_CEC_CallbackIDTypeDef CallbackID, pCEC_CallbackTypeDef pCallback);
+HAL_StatusTypeDef HAL_CEC_UnRegisterCallback(CEC_HandleTypeDef *hcec, HAL_CEC_CallbackIDTypeDef CallbackID);
+
+HAL_StatusTypeDef HAL_CEC_RegisterRxCpltCallback(CEC_HandleTypeDef *hcec, pCEC_RxCallbackTypeDef pCallback);
+HAL_StatusTypeDef HAL_CEC_UnRegisterRxCpltCallback(CEC_HandleTypeDef *hcec);
+#endif /* USE_HAL_CEC_REGISTER_CALLBACKS */
+/**
+  * @}
+  */
+
+/** @addtogroup CEC_Exported_Functions_Group2 Input and Output operation functions 
+  *  @brief CEC Transmit/Receive functions 
+  * @{
+  */
+/* I/O operation functions  ***************************************************/
+HAL_StatusTypeDef HAL_CEC_Transmit_IT(CEC_HandleTypeDef *hcec, uint8_t InitiatorAddress,uint8_t DestinationAddress, uint8_t *pData, uint32_t Size);
+uint32_t HAL_CEC_GetLastReceivedFrameSize(CEC_HandleTypeDef *hcec);
+void HAL_CEC_ChangeRxBuffer(CEC_HandleTypeDef *hcec, uint8_t* Rxbuffer);
+void HAL_CEC_IRQHandler(CEC_HandleTypeDef *hcec);
+void HAL_CEC_TxCpltCallback(CEC_HandleTypeDef *hcec);
+void HAL_CEC_RxCpltCallback(CEC_HandleTypeDef *hcec, uint32_t RxFrameSize);
+void HAL_CEC_ErrorCallback(CEC_HandleTypeDef *hcec);
+/**
+  * @}
+  */
+
+/** @defgroup CEC_Exported_Functions_Group3 Peripheral Control functions 
+  *  @brief   CEC control functions 
+  * @{
+  */
+/* Peripheral State and Error functions ***************************************/
+HAL_CEC_StateTypeDef HAL_CEC_GetState(CEC_HandleTypeDef *hcec);
+uint32_t HAL_CEC_GetError(CEC_HandleTypeDef *hcec);
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+  
+/* Private types -------------------------------------------------------------*/
+/** @defgroup CEC_Private_Types CEC Private Types
+  * @{
+  */
+
+/**
+  * @}
+  */ 
+
+/* Private variables ---------------------------------------------------------*/
+/** @defgroup CEC_Private_Variables CEC Private Variables
+  * @{
+  */
+  
+/**
+  * @}
+  */ 
+
+/* Private constants ---------------------------------------------------------*/
+/** @defgroup CEC_Private_Constants CEC Private Constants
+  * @{
+  */
+
+/**
+  * @}
+  */ 
+
+/* Private macros ------------------------------------------------------------*/
+/** @defgroup CEC_Private_Macros CEC Private Macros
+  * @{
+  */
+#define IS_CEC_BIT_TIMING_ERROR_MODE(MODE) (((MODE) == CEC_BIT_TIMING_ERROR_MODE_STANDARD) || \
+                                            ((MODE) == CEC_BIT_TIMING_ERROR_MODE_ERRORFREE))
+
+#define IS_CEC_BIT_PERIOD_ERROR_MODE(MODE) (((MODE) == CEC_BIT_PERIOD_ERROR_MODE_STANDARD) || \
+                                            ((MODE) == CEC_BIT_PERIOD_ERROR_MODE_FLEXIBLE))
+
+/** @brief Check CEC message size.
+  *       The message size is the payload size: without counting the header, 
+  *       it varies from 0 byte (ping operation, one header only, no payload) to 
+  *       15 bytes (1 opcode and up to 14 operands following the header). 
+  * @param  __SIZE__: CEC message size.               
+  * @retval Test result (TRUE or FALSE).
+  */
+#define IS_CEC_MSGSIZE(__SIZE__) ((__SIZE__) <= 0x10U)
+/** @brief Check CEC device Own Address Register (OAR) setting.
+  * @param  __ADDRESS__: CEC own address.               
+  * @retval Test result (TRUE or FALSE).
+  */
+#define IS_CEC_OWN_ADDRESS(__ADDRESS__) ((__ADDRESS__) <= 0x0000000FU)
+
+/** @brief Check CEC initiator or destination logical address setting.
+  *        Initiator and destination addresses are coded over 4 bits. 
+  * @param  __ADDRESS__: CEC initiator or logical address.               
+  * @retval Test result (TRUE or FALSE).
+  */
+#define IS_CEC_ADDRESS(__ADDRESS__) ((__ADDRESS__) <= 0x0000000FU)
+
+
+
+/**
+  * @}
+  */
+/* Private functions ---------------------------------------------------------*/
+/** @defgroup CEC_Private_Functions CEC Private Functions
+  * @{
+  */
+  
+/**
+  * @}
+  */
+  
+/**
+  * @}
+  */ 
+
+/**
+  * @}
+  */ 
+
+#endif /* CEC */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F1xx_HAL_CEC_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_conf_template.h

@@ -0,0 +1,399 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_hal_conf.h
+  * @author  MCD Application Team
+  * @brief   HAL configuration template file.
+  *          This file should be copied to the application folder and renamed
+  *          to stm32f1xx_hal_conf.h.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2017 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F1xx_HAL_CONF_H
+#define __STM32F1xx_HAL_CONF_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Exported types ------------------------------------------------------------*/
+/* Exported constants --------------------------------------------------------*/
+
+/* ########################## Module Selection ############################## */
+/**
+  * @brief This is the list of modules to be used in the HAL driver
+  */
+#define HAL_MODULE_ENABLED
+#define HAL_ADC_MODULE_ENABLED
+#define HAL_CAN_MODULE_ENABLED
+/* #define HAL_CAN_LEGACY_MODULE_ENABLED */
+#define HAL_CEC_MODULE_ENABLED
+#define HAL_CORTEX_MODULE_ENABLED
+#define HAL_CRC_MODULE_ENABLED
+#define HAL_DAC_MODULE_ENABLED
+#define HAL_DMA_MODULE_ENABLED
+#define HAL_ETH_MODULE_ENABLED
+#define HAL_EXTI_MODULE_ENABLED
+#define HAL_FLASH_MODULE_ENABLED
+#define HAL_GPIO_MODULE_ENABLED
+#define HAL_HCD_MODULE_ENABLED
+#define HAL_I2C_MODULE_ENABLED
+#define HAL_I2S_MODULE_ENABLED
+#define HAL_IRDA_MODULE_ENABLED
+#define HAL_IWDG_MODULE_ENABLED
+#define HAL_NAND_MODULE_ENABLED
+#define HAL_NOR_MODULE_ENABLED
+#define HAL_PCCARD_MODULE_ENABLED
+#define HAL_PCD_MODULE_ENABLED
+#define HAL_PWR_MODULE_ENABLED
+#define HAL_RCC_MODULE_ENABLED
+#define HAL_RTC_MODULE_ENABLED
+#define HAL_SD_MODULE_ENABLED
+#define HAL_SMARTCARD_MODULE_ENABLED
+#define HAL_SPI_MODULE_ENABLED
+#define HAL_SRAM_MODULE_ENABLED
+#define HAL_TIM_MODULE_ENABLED
+#define HAL_UART_MODULE_ENABLED
+#define HAL_USART_MODULE_ENABLED
+#define HAL_WWDG_MODULE_ENABLED
+#define HAL_MMC_MODULE_ENABLED
+
+/* ########################## Oscillator Values adaptation ####################*/
+/**
+  * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
+  *        This value is used by the RCC HAL module to compute the system frequency
+  *        (when HSE is used as system clock source, directly or through the PLL).
+  */
+#if !defined  (HSE_VALUE)
+#if defined(USE_STM3210C_EVAL)
+#define HSE_VALUE    25000000U /*!< Value of the External oscillator in Hz */
+#else
+#define HSE_VALUE    8000000U /*!< Value of the External oscillator in Hz */
+#endif
+#endif /* HSE_VALUE */
+
+#if !defined  (HSE_STARTUP_TIMEOUT)
+#define HSE_STARTUP_TIMEOUT    100U      /*!< Time out for HSE start up, in ms */
+#endif /* HSE_STARTUP_TIMEOUT */
+
+/**
+  * @brief Internal High Speed oscillator (HSI) value.
+  *        This value is used by the RCC HAL module to compute the system frequency
+  *        (when HSI is used as system clock source, directly or through the PLL).
+  */
+#if !defined  (HSI_VALUE)
+#define HSI_VALUE              8000000U  /*!< Value of the Internal oscillator in Hz */
+#endif /* HSI_VALUE */
+
+/**
+  * @brief Internal Low Speed oscillator (LSI) value.
+  */
+#if !defined  (LSI_VALUE)
+#define LSI_VALUE               40000U     /*!< LSI Typical Value in Hz */
+#endif /* LSI_VALUE */                     /*!< Value of the Internal Low Speed oscillator in Hz
+                                                The real value may vary depending on the variations
+                                                in voltage and temperature. */
+/**
+  * @brief External Low Speed oscillator (LSE) value.
+  *        This value is used by the UART, RTC HAL module to compute the system frequency
+  */
+#if !defined  (LSE_VALUE)
+#define LSE_VALUE               32768U    /*!< Value of the External Low Speed oscillator in Hz */
+#endif /* LSE_VALUE */
+
+#if !defined  (LSE_STARTUP_TIMEOUT)
+#define LSE_STARTUP_TIMEOUT    5000U     /*!< Time out for LSE start up, in ms */
+#endif /* LSE_STARTUP_TIMEOUT */
+
+/* Tip: To avoid modifying this file each time you need to use different HSE,
+   ===  you can define the HSE value in your toolchain compiler preprocessor. */
+
+/* ########################### System Configuration ######################### */
+/**
+  * @brief This is the HAL system configuration section
+  */
+#define  VDD_VALUE                    3300U /*!< Value of VDD in mv */
+#define  TICK_INT_PRIORITY            0x0FU /*!< tick interrupt priority */
+#define  USE_RTOS                     0U
+#define  PREFETCH_ENABLE              1U
+
+#define  USE_HAL_ADC_REGISTER_CALLBACKS         0U /* ADC register callback disabled       */
+#define  USE_HAL_CAN_REGISTER_CALLBACKS         0U /* CAN register callback disabled       */
+#define  USE_HAL_CEC_REGISTER_CALLBACKS         0U /* CEC register callback disabled       */
+#define  USE_HAL_DAC_REGISTER_CALLBACKS         0U /* DAC register callback disabled       */
+#define  USE_HAL_ETH_REGISTER_CALLBACKS         0U /* ETH register callback disabled       */
+#define  USE_HAL_HCD_REGISTER_CALLBACKS         0U /* HCD register callback disabled       */
+#define  USE_HAL_I2C_REGISTER_CALLBACKS         0U /* I2C register callback disabled       */
+#define  USE_HAL_I2S_REGISTER_CALLBACKS         0U /* I2S register callback disabled       */
+#define  USE_HAL_MMC_REGISTER_CALLBACKS         0U /* MMC register callback disabled       */
+#define  USE_HAL_NAND_REGISTER_CALLBACKS        0U /* NAND register callback disabled      */
+#define  USE_HAL_NOR_REGISTER_CALLBACKS         0U /* NOR register callback disabled       */
+#define  USE_HAL_PCCARD_REGISTER_CALLBACKS      0U /* PCCARD register callback disabled    */
+#define  USE_HAL_PCD_REGISTER_CALLBACKS         0U /* PCD register callback disabled       */
+#define  USE_HAL_RTC_REGISTER_CALLBACKS         0U /* RTC register callback disabled       */
+#define  USE_HAL_SD_REGISTER_CALLBACKS          0U /* SD register callback disabled        */
+#define  USE_HAL_SMARTCARD_REGISTER_CALLBACKS   0U /* SMARTCARD register callback disabled */
+#define  USE_HAL_IRDA_REGISTER_CALLBACKS        0U /* IRDA register callback disabled      */
+#define  USE_HAL_SRAM_REGISTER_CALLBACKS        0U /* SRAM register callback disabled      */
+#define  USE_HAL_SPI_REGISTER_CALLBACKS         0U /* SPI register callback disabled       */
+#define  USE_HAL_TIM_REGISTER_CALLBACKS         0U /* TIM register callback disabled       */
+#define  USE_HAL_UART_REGISTER_CALLBACKS        0U /* UART register callback disabled      */
+#define  USE_HAL_USART_REGISTER_CALLBACKS       0U /* USART register callback disabled     */
+#define  USE_HAL_WWDG_REGISTER_CALLBACKS        0U /* WWDG register callback disabled      */
+
+/* ########################## Assert Selection ############################## */
+/**
+  * @brief Uncomment the line below to expanse the "assert_param" macro in the
+  *        HAL drivers code
+  */
+/* #define USE_FULL_ASSERT    1U */
+
+/* ################## Ethernet peripheral configuration ##################### */
+
+/* Section 1 : Ethernet peripheral configuration */
+
+/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */
+#define MAC_ADDR0   2U
+#define MAC_ADDR1   0U
+#define MAC_ADDR2   0U
+#define MAC_ADDR3   0U
+#define MAC_ADDR4   0U
+#define MAC_ADDR5   0U
+
+/* Definition of the Ethernet driver buffers size and count */
+#define ETH_RX_BUF_SIZE                ETH_MAX_PACKET_SIZE /* buffer size for receive               */
+#define ETH_TX_BUF_SIZE                ETH_MAX_PACKET_SIZE /* buffer size for transmit              */
+#define ETH_RXBUFNB                    8U                  /* 8 Rx buffers of size ETH_RX_BUF_SIZE  */
+#define ETH_TXBUFNB                    4U                  /* 4 Tx buffers of size ETH_TX_BUF_SIZE  */
+
+/* Section 2: PHY configuration section */
+
+/* DP83848 PHY Address*/
+#define DP83848_PHY_ADDRESS             0x01U
+/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/
+#define PHY_RESET_DELAY                 0x000000FFU
+/* PHY Configuration delay */
+#define PHY_CONFIG_DELAY                0x00000FFFU
+
+#define PHY_READ_TO                     0x0000FFFFU
+#define PHY_WRITE_TO                    0x0000FFFFU
+
+/* Section 3: Common PHY Registers */
+
+#define PHY_BCR                         ((uint16_t)0x0000)  /*!< Transceiver Basic Control Register   */
+#define PHY_BSR                         ((uint16_t)0x0001)  /*!< Transceiver Basic Status Register    */
+
+#define PHY_RESET                       ((uint16_t)0x8000)  /*!< PHY Reset */
+#define PHY_LOOPBACK                    ((uint16_t)0x4000)  /*!< Select loop-back mode */
+#define PHY_FULLDUPLEX_100M             ((uint16_t)0x2100)  /*!< Set the full-duplex mode at 100 Mb/s */
+#define PHY_HALFDUPLEX_100M             ((uint16_t)0x2000)  /*!< Set the half-duplex mode at 100 Mb/s */
+#define PHY_FULLDUPLEX_10M              ((uint16_t)0x0100)  /*!< Set the full-duplex mode at 10 Mb/s  */
+#define PHY_HALFDUPLEX_10M              ((uint16_t)0x0000)  /*!< Set the half-duplex mode at 10 Mb/s  */
+#define PHY_AUTONEGOTIATION             ((uint16_t)0x1000)  /*!< Enable auto-negotiation function     */
+#define PHY_RESTART_AUTONEGOTIATION     ((uint16_t)0x0200)  /*!< Restart auto-negotiation function    */
+#define PHY_POWERDOWN                   ((uint16_t)0x0800)  /*!< Select the power down mode           */
+#define PHY_ISOLATE                     ((uint16_t)0x0400)  /*!< Isolate PHY from MII                 */
+
+#define PHY_AUTONEGO_COMPLETE           ((uint16_t)0x0020)  /*!< Auto-Negotiation process completed   */
+#define PHY_LINKED_STATUS               ((uint16_t)0x0004)  /*!< Valid link established               */
+#define PHY_JABBER_DETECTION            ((uint16_t)0x0002)  /*!< Jabber condition detected            */
+
+/* Section 4: Extended PHY Registers */
+
+#define PHY_SR                          ((uint16_t)0x0010)  /*!< PHY status register Offset                      */
+#define PHY_MICR                        ((uint16_t)0x0011)  /*!< MII Interrupt Control Register                  */
+#define PHY_MISR                        ((uint16_t)0x0012)  /*!< MII Interrupt Status and Misc. Control Register */
+
+#define PHY_LINK_STATUS                 ((uint16_t)0x0001)  /*!< PHY Link mask                                   */
+#define PHY_SPEED_STATUS                ((uint16_t)0x0002)  /*!< PHY Speed mask                                  */
+#define PHY_DUPLEX_STATUS               ((uint16_t)0x0004)  /*!< PHY Duplex mask                                 */
+
+#define PHY_MICR_INT_EN                 ((uint16_t)0x0002)  /*!< PHY Enable interrupts                           */
+#define PHY_MICR_INT_OE                 ((uint16_t)0x0001)  /*!< PHY Enable output interrupt events              */
+
+#define PHY_MISR_LINK_INT_EN            ((uint16_t)0x0020)  /*!< Enable Interrupt on change of link status       */
+#define PHY_LINK_INTERRUPT              ((uint16_t)0x2000)  /*!< PHY link status interrupt mask                  */
+
+/* ################## SPI peripheral configuration ########################## */
+
+/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver
+* Activated: CRC code is present inside driver
+* Deactivated: CRC code cleaned from driver
+*/
+
+#define USE_SPI_CRC                     1U
+
+/* Includes ------------------------------------------------------------------*/
+/**
+  * @brief Include module's header file
+  */
+
+#ifdef HAL_RCC_MODULE_ENABLED
+#include "stm32f1xx_hal_rcc.h"
+#endif /* HAL_RCC_MODULE_ENABLED */
+
+#ifdef HAL_GPIO_MODULE_ENABLED
+#include "stm32f1xx_hal_gpio.h"
+#endif /* HAL_GPIO_MODULE_ENABLED */
+
+#ifdef HAL_EXTI_MODULE_ENABLED
+#include "stm32f1xx_hal_exti.h"
+#endif /* HAL_EXTI_MODULE_ENABLED */
+
+#ifdef HAL_DMA_MODULE_ENABLED
+#include "stm32f1xx_hal_dma.h"
+#endif /* HAL_DMA_MODULE_ENABLED */
+
+#ifdef HAL_ETH_MODULE_ENABLED
+#include "stm32f1xx_hal_eth.h"
+#endif /* HAL_ETH_MODULE_ENABLED */
+
+#ifdef HAL_CAN_MODULE_ENABLED
+#include "stm32f1xx_hal_can.h"
+#endif /* HAL_CAN_MODULE_ENABLED */
+
+#ifdef HAL_CAN_LEGACY_MODULE_ENABLED
+  #include "Legacy/stm32f1xx_hal_can_legacy.h"
+#endif /* HAL_CAN_LEGACY_MODULE_ENABLED */
+
+#ifdef HAL_CEC_MODULE_ENABLED
+#include "stm32f1xx_hal_cec.h"
+#endif /* HAL_CEC_MODULE_ENABLED */
+
+#ifdef HAL_CORTEX_MODULE_ENABLED
+#include "stm32f1xx_hal_cortex.h"
+#endif /* HAL_CORTEX_MODULE_ENABLED */
+
+#ifdef HAL_ADC_MODULE_ENABLED
+#include "stm32f1xx_hal_adc.h"
+#endif /* HAL_ADC_MODULE_ENABLED */
+
+#ifdef HAL_CRC_MODULE_ENABLED
+#include "stm32f1xx_hal_crc.h"
+#endif /* HAL_CRC_MODULE_ENABLED */
+
+#ifdef HAL_DAC_MODULE_ENABLED
+#include "stm32f1xx_hal_dac.h"
+#endif /* HAL_DAC_MODULE_ENABLED */
+
+#ifdef HAL_FLASH_MODULE_ENABLED
+#include "stm32f1xx_hal_flash.h"
+#endif /* HAL_FLASH_MODULE_ENABLED */
+
+#ifdef HAL_SRAM_MODULE_ENABLED
+#include "stm32f1xx_hal_sram.h"
+#endif /* HAL_SRAM_MODULE_ENABLED */
+
+#ifdef HAL_NOR_MODULE_ENABLED
+#include "stm32f1xx_hal_nor.h"
+#endif /* HAL_NOR_MODULE_ENABLED */
+
+#ifdef HAL_I2C_MODULE_ENABLED
+#include "stm32f1xx_hal_i2c.h"
+#endif /* HAL_I2C_MODULE_ENABLED */
+
+#ifdef HAL_I2S_MODULE_ENABLED
+#include "stm32f1xx_hal_i2s.h"
+#endif /* HAL_I2S_MODULE_ENABLED */
+
+#ifdef HAL_IWDG_MODULE_ENABLED
+#include "stm32f1xx_hal_iwdg.h"
+#endif /* HAL_IWDG_MODULE_ENABLED */
+
+#ifdef HAL_PWR_MODULE_ENABLED
+#include "stm32f1xx_hal_pwr.h"
+#endif /* HAL_PWR_MODULE_ENABLED */
+
+#ifdef HAL_RTC_MODULE_ENABLED
+#include "stm32f1xx_hal_rtc.h"
+#endif /* HAL_RTC_MODULE_ENABLED */
+
+#ifdef HAL_PCCARD_MODULE_ENABLED
+#include "stm32f1xx_hal_pccard.h"
+#endif /* HAL_PCCARD_MODULE_ENABLED */
+
+#ifdef HAL_SD_MODULE_ENABLED
+#include "stm32f1xx_hal_sd.h"
+#endif /* HAL_SD_MODULE_ENABLED */
+
+#ifdef HAL_NAND_MODULE_ENABLED
+#include "stm32f1xx_hal_nand.h"
+#endif /* HAL_NAND_MODULE_ENABLED */
+
+#ifdef HAL_SPI_MODULE_ENABLED
+#include "stm32f1xx_hal_spi.h"
+#endif /* HAL_SPI_MODULE_ENABLED */
+
+#ifdef HAL_TIM_MODULE_ENABLED
+#include "stm32f1xx_hal_tim.h"
+#endif /* HAL_TIM_MODULE_ENABLED */
+
+#ifdef HAL_UART_MODULE_ENABLED
+#include "stm32f1xx_hal_uart.h"
+#endif /* HAL_UART_MODULE_ENABLED */
+
+#ifdef HAL_USART_MODULE_ENABLED
+#include "stm32f1xx_hal_usart.h"
+#endif /* HAL_USART_MODULE_ENABLED */
+
+#ifdef HAL_IRDA_MODULE_ENABLED
+#include "stm32f1xx_hal_irda.h"
+#endif /* HAL_IRDA_MODULE_ENABLED */
+
+#ifdef HAL_SMARTCARD_MODULE_ENABLED
+#include "stm32f1xx_hal_smartcard.h"
+#endif /* HAL_SMARTCARD_MODULE_ENABLED */
+
+#ifdef HAL_WWDG_MODULE_ENABLED
+#include "stm32f1xx_hal_wwdg.h"
+#endif /* HAL_WWDG_MODULE_ENABLED */
+
+#ifdef HAL_PCD_MODULE_ENABLED
+#include "stm32f1xx_hal_pcd.h"
+#endif /* HAL_PCD_MODULE_ENABLED */
+
+#ifdef HAL_HCD_MODULE_ENABLED
+#include "stm32f1xx_hal_hcd.h"
+#endif /* HAL_HCD_MODULE_ENABLED */
+
+#ifdef HAL_MMC_MODULE_ENABLED
+#include "stm32f1xx_hal_mmc.h"
+#endif /* HAL_MMC_MODULE_ENABLED */
+
+/* Exported macro ------------------------------------------------------------*/
+#ifdef  USE_FULL_ASSERT
+/**
+  * @brief  The assert_param macro is used for function's parameters check.
+  * @param  expr If expr is false, it calls assert_failed function
+  *         which reports the name of the source file and the source
+  *         line number of the call that failed.
+  *         If expr is true, it returns no value.
+  * @retval None
+  */
+#define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__))
+/* Exported functions ------------------------------------------------------- */
+void assert_failed(uint8_t* file, uint32_t line);
+#else
+#define assert_param(expr) ((void)0U)
+#endif /* USE_FULL_ASSERT */
+
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F1xx_HAL_CONF_H */
+
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_cortex.h

@@ -0,0 +1,410 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_hal_cortex.h
+  * @author  MCD Application Team
+  * @brief   Header file of CORTEX HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2017 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F1xx_HAL_CORTEX_H
+#define __STM32F1xx_HAL_CORTEX_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_hal_def.h"
+
+/** @addtogroup STM32F1xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup CORTEX
+  * @{
+  */ 
+/* Exported types ------------------------------------------------------------*/
+/** @defgroup CORTEX_Exported_Types Cortex Exported Types
+  * @{
+  */
+
+#if (__MPU_PRESENT == 1U)
+/** @defgroup CORTEX_MPU_Region_Initialization_Structure_definition MPU Region Initialization Structure Definition
+  * @brief  MPU Region initialization structure 
+  * @{
+  */
+typedef struct
+{
+  uint8_t                Enable;                /*!< Specifies the status of the region. 
+                                                     This parameter can be a value of @ref CORTEX_MPU_Region_Enable                 */
+  uint8_t                Number;                /*!< Specifies the number of the region to protect. 
+                                                     This parameter can be a value of @ref CORTEX_MPU_Region_Number                 */
+  uint32_t               BaseAddress;           /*!< Specifies the base address of the region to protect.                           */
+  uint8_t                Size;                  /*!< Specifies the size of the region to protect. 
+                                                     This parameter can be a value of @ref CORTEX_MPU_Region_Size                   */
+  uint8_t                SubRegionDisable;      /*!< Specifies the number of the subregion protection to disable. 
+                                                     This parameter must be a number between Min_Data = 0x00 and Max_Data = 0xFF    */         
+  uint8_t                TypeExtField;          /*!< Specifies the TEX field level.
+                                                     This parameter can be a value of @ref CORTEX_MPU_TEX_Levels                    */                 
+  uint8_t                AccessPermission;      /*!< Specifies the region access permission type. 
+                                                     This parameter can be a value of @ref CORTEX_MPU_Region_Permission_Attributes  */
+  uint8_t                DisableExec;           /*!< Specifies the instruction access status. 
+                                                     This parameter can be a value of @ref CORTEX_MPU_Instruction_Access            */
+  uint8_t                IsShareable;           /*!< Specifies the shareability status of the protected region. 
+                                                     This parameter can be a value of @ref CORTEX_MPU_Access_Shareable              */
+  uint8_t                IsCacheable;           /*!< Specifies the cacheable status of the region protected. 
+                                                     This parameter can be a value of @ref CORTEX_MPU_Access_Cacheable              */
+  uint8_t                IsBufferable;          /*!< Specifies the bufferable status of the protected region. 
+                                                     This parameter can be a value of @ref CORTEX_MPU_Access_Bufferable             */
+}MPU_Region_InitTypeDef;
+/**
+  * @}
+  */
+#endif /* __MPU_PRESENT */
+
+/**
+  * @}
+  */
+
+/* Exported constants --------------------------------------------------------*/
+
+/** @defgroup CORTEX_Exported_Constants CORTEX Exported Constants
+  * @{
+  */
+
+/** @defgroup CORTEX_Preemption_Priority_Group CORTEX Preemption Priority Group
+  * @{
+  */
+#define NVIC_PRIORITYGROUP_0         0x00000007U /*!< 0 bits for pre-emption priority
+                                                      4 bits for subpriority */
+#define NVIC_PRIORITYGROUP_1         0x00000006U /*!< 1 bits for pre-emption priority
+                                                      3 bits for subpriority */
+#define NVIC_PRIORITYGROUP_2         0x00000005U /*!< 2 bits for pre-emption priority
+                                                      2 bits for subpriority */
+#define NVIC_PRIORITYGROUP_3         0x00000004U /*!< 3 bits for pre-emption priority
+                                                      1 bits for subpriority */
+#define NVIC_PRIORITYGROUP_4         0x00000003U /*!< 4 bits for pre-emption priority
+                                                      0 bits for subpriority */
+/**
+  * @}
+  */
+
+/** @defgroup CORTEX_SysTick_clock_source CORTEX _SysTick clock source 
+  * @{
+  */
+#define SYSTICK_CLKSOURCE_HCLK_DIV8    0x00000000U
+#define SYSTICK_CLKSOURCE_HCLK         0x00000004U
+
+/**
+  * @}
+  */
+
+#if (__MPU_PRESENT == 1)
+/** @defgroup CORTEX_MPU_HFNMI_PRIVDEF_Control MPU HFNMI and PRIVILEGED Access control
+  * @{
+  */
+#define  MPU_HFNMI_PRIVDEF_NONE           0x00000000U
+#define  MPU_HARDFAULT_NMI                MPU_CTRL_HFNMIENA_Msk
+#define  MPU_PRIVILEGED_DEFAULT           MPU_CTRL_PRIVDEFENA_Msk
+#define  MPU_HFNMI_PRIVDEF               (MPU_CTRL_HFNMIENA_Msk | MPU_CTRL_PRIVDEFENA_Msk)
+
+/**
+  * @}
+  */
+
+/** @defgroup CORTEX_MPU_Region_Enable CORTEX MPU Region Enable
+  * @{
+  */
+#define  MPU_REGION_ENABLE     ((uint8_t)0x01)
+#define  MPU_REGION_DISABLE    ((uint8_t)0x00)
+/**
+  * @}
+  */
+
+/** @defgroup CORTEX_MPU_Instruction_Access CORTEX MPU Instruction Access
+  * @{
+  */
+#define  MPU_INSTRUCTION_ACCESS_ENABLE      ((uint8_t)0x00)
+#define  MPU_INSTRUCTION_ACCESS_DISABLE     ((uint8_t)0x01)
+/**
+  * @}
+  */
+
+/** @defgroup CORTEX_MPU_Access_Shareable CORTEX MPU Instruction Access Shareable
+  * @{
+  */
+#define  MPU_ACCESS_SHAREABLE        ((uint8_t)0x01)
+#define  MPU_ACCESS_NOT_SHAREABLE    ((uint8_t)0x00)
+/**
+  * @}
+  */
+
+/** @defgroup CORTEX_MPU_Access_Cacheable CORTEX MPU Instruction Access Cacheable
+  * @{
+  */
+#define  MPU_ACCESS_CACHEABLE         ((uint8_t)0x01)
+#define  MPU_ACCESS_NOT_CACHEABLE     ((uint8_t)0x00)
+/**
+  * @}
+  */
+
+/** @defgroup CORTEX_MPU_Access_Bufferable CORTEX MPU Instruction Access Bufferable
+  * @{
+  */
+#define  MPU_ACCESS_BUFFERABLE         ((uint8_t)0x01)
+#define  MPU_ACCESS_NOT_BUFFERABLE     ((uint8_t)0x00)
+/**
+  * @}
+  */
+
+/** @defgroup CORTEX_MPU_TEX_Levels MPU TEX Levels
+  * @{
+  */
+#define  MPU_TEX_LEVEL0    ((uint8_t)0x00)
+#define  MPU_TEX_LEVEL1    ((uint8_t)0x01)
+#define  MPU_TEX_LEVEL2    ((uint8_t)0x02)
+/**
+  * @}
+  */
+
+/** @defgroup CORTEX_MPU_Region_Size CORTEX MPU Region Size
+  * @{
+  */
+#define   MPU_REGION_SIZE_32B      ((uint8_t)0x04)
+#define   MPU_REGION_SIZE_64B      ((uint8_t)0x05)
+#define   MPU_REGION_SIZE_128B     ((uint8_t)0x06)
+#define   MPU_REGION_SIZE_256B     ((uint8_t)0x07)
+#define   MPU_REGION_SIZE_512B     ((uint8_t)0x08)
+#define   MPU_REGION_SIZE_1KB      ((uint8_t)0x09)
+#define   MPU_REGION_SIZE_2KB      ((uint8_t)0x0A)
+#define   MPU_REGION_SIZE_4KB      ((uint8_t)0x0B)
+#define   MPU_REGION_SIZE_8KB      ((uint8_t)0x0C)
+#define   MPU_REGION_SIZE_16KB     ((uint8_t)0x0D)
+#define   MPU_REGION_SIZE_32KB     ((uint8_t)0x0E)
+#define   MPU_REGION_SIZE_64KB     ((uint8_t)0x0F)
+#define   MPU_REGION_SIZE_128KB    ((uint8_t)0x10)
+#define   MPU_REGION_SIZE_256KB    ((uint8_t)0x11)
+#define   MPU_REGION_SIZE_512KB    ((uint8_t)0x12)
+#define   MPU_REGION_SIZE_1MB      ((uint8_t)0x13)
+#define   MPU_REGION_SIZE_2MB      ((uint8_t)0x14)
+#define   MPU_REGION_SIZE_4MB      ((uint8_t)0x15)
+#define   MPU_REGION_SIZE_8MB      ((uint8_t)0x16)
+#define   MPU_REGION_SIZE_16MB     ((uint8_t)0x17)
+#define   MPU_REGION_SIZE_32MB     ((uint8_t)0x18)
+#define   MPU_REGION_SIZE_64MB     ((uint8_t)0x19)
+#define   MPU_REGION_SIZE_128MB    ((uint8_t)0x1A)
+#define   MPU_REGION_SIZE_256MB    ((uint8_t)0x1B)
+#define   MPU_REGION_SIZE_512MB    ((uint8_t)0x1C)
+#define   MPU_REGION_SIZE_1GB      ((uint8_t)0x1D)
+#define   MPU_REGION_SIZE_2GB      ((uint8_t)0x1E)
+#define   MPU_REGION_SIZE_4GB      ((uint8_t)0x1F)
+/**
+  * @}
+  */
+   
+/** @defgroup CORTEX_MPU_Region_Permission_Attributes CORTEX MPU Region Permission Attributes 
+  * @{
+  */
+#define  MPU_REGION_NO_ACCESS      ((uint8_t)0x00)
+#define  MPU_REGION_PRIV_RW        ((uint8_t)0x01)
+#define  MPU_REGION_PRIV_RW_URO    ((uint8_t)0x02)
+#define  MPU_REGION_FULL_ACCESS    ((uint8_t)0x03)
+#define  MPU_REGION_PRIV_RO        ((uint8_t)0x05)
+#define  MPU_REGION_PRIV_RO_URO    ((uint8_t)0x06)
+/**
+  * @}
+  */
+
+/** @defgroup CORTEX_MPU_Region_Number CORTEX MPU Region Number
+  * @{
+  */
+#define  MPU_REGION_NUMBER0    ((uint8_t)0x00)
+#define  MPU_REGION_NUMBER1    ((uint8_t)0x01)
+#define  MPU_REGION_NUMBER2    ((uint8_t)0x02)
+#define  MPU_REGION_NUMBER3    ((uint8_t)0x03)
+#define  MPU_REGION_NUMBER4    ((uint8_t)0x04)
+#define  MPU_REGION_NUMBER5    ((uint8_t)0x05)
+#define  MPU_REGION_NUMBER6    ((uint8_t)0x06)
+#define  MPU_REGION_NUMBER7    ((uint8_t)0x07)
+/**
+  * @}
+  */
+#endif /* __MPU_PRESENT */
+
+/**
+  * @}
+  */
+
+
+/* Exported Macros -----------------------------------------------------------*/
+
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup CORTEX_Exported_Functions
+  * @{
+  */
+  
+/** @addtogroup CORTEX_Exported_Functions_Group1
+  * @{
+  */
+/* Initialization and de-initialization functions *****************************/
+void HAL_NVIC_SetPriorityGrouping(uint32_t PriorityGroup);
+void HAL_NVIC_SetPriority(IRQn_Type IRQn, uint32_t PreemptPriority, uint32_t SubPriority);
+void HAL_NVIC_EnableIRQ(IRQn_Type IRQn);
+void HAL_NVIC_DisableIRQ(IRQn_Type IRQn);
+void HAL_NVIC_SystemReset(void);
+uint32_t HAL_SYSTICK_Config(uint32_t TicksNumb);
+/**
+  * @}
+  */
+
+/** @addtogroup CORTEX_Exported_Functions_Group2
+  * @{
+  */
+/* Peripheral Control functions ***********************************************/
+uint32_t HAL_NVIC_GetPriorityGrouping(void);
+void HAL_NVIC_GetPriority(IRQn_Type IRQn, uint32_t PriorityGroup, uint32_t* pPreemptPriority, uint32_t* pSubPriority);
+uint32_t HAL_NVIC_GetPendingIRQ(IRQn_Type IRQn);
+void HAL_NVIC_SetPendingIRQ(IRQn_Type IRQn);
+void HAL_NVIC_ClearPendingIRQ(IRQn_Type IRQn);
+uint32_t HAL_NVIC_GetActive(IRQn_Type IRQn);
+void HAL_SYSTICK_CLKSourceConfig(uint32_t CLKSource);
+void HAL_SYSTICK_IRQHandler(void);
+void HAL_SYSTICK_Callback(void);
+
+#if (__MPU_PRESENT == 1U)
+void HAL_MPU_Enable(uint32_t MPU_Control);
+void HAL_MPU_Disable(void);
+void HAL_MPU_ConfigRegion(MPU_Region_InitTypeDef *MPU_Init);
+#endif /* __MPU_PRESENT */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Private types -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private constants ---------------------------------------------------------*/
+/* Private macros ------------------------------------------------------------*/
+/** @defgroup CORTEX_Private_Macros CORTEX Private Macros
+  * @{
+  */
+#define IS_NVIC_PRIORITY_GROUP(GROUP) (((GROUP) == NVIC_PRIORITYGROUP_0) || \
+                                       ((GROUP) == NVIC_PRIORITYGROUP_1) || \
+                                       ((GROUP) == NVIC_PRIORITYGROUP_2) || \
+                                       ((GROUP) == NVIC_PRIORITYGROUP_3) || \
+                                       ((GROUP) == NVIC_PRIORITYGROUP_4))
+
+#define IS_NVIC_PREEMPTION_PRIORITY(PRIORITY)  ((PRIORITY) < 0x10U)
+
+#define IS_NVIC_SUB_PRIORITY(PRIORITY)         ((PRIORITY) < 0x10U)
+
+#define IS_NVIC_DEVICE_IRQ(IRQ)                ((IRQ) >= (IRQn_Type)0x00U)
+
+#define IS_SYSTICK_CLK_SOURCE(SOURCE) (((SOURCE) == SYSTICK_CLKSOURCE_HCLK) || \
+                                       ((SOURCE) == SYSTICK_CLKSOURCE_HCLK_DIV8))
+
+#if (__MPU_PRESENT == 1U)
+#define IS_MPU_REGION_ENABLE(STATE) (((STATE) == MPU_REGION_ENABLE) || \
+                                     ((STATE) == MPU_REGION_DISABLE))
+
+#define IS_MPU_INSTRUCTION_ACCESS(STATE) (((STATE) == MPU_INSTRUCTION_ACCESS_ENABLE) || \
+                                          ((STATE) == MPU_INSTRUCTION_ACCESS_DISABLE))
+
+#define IS_MPU_ACCESS_SHAREABLE(STATE)   (((STATE) == MPU_ACCESS_SHAREABLE) || \
+                                          ((STATE) == MPU_ACCESS_NOT_SHAREABLE))
+
+#define IS_MPU_ACCESS_CACHEABLE(STATE)   (((STATE) == MPU_ACCESS_CACHEABLE) || \
+                                          ((STATE) == MPU_ACCESS_NOT_CACHEABLE))
+
+#define IS_MPU_ACCESS_BUFFERABLE(STATE)   (((STATE) == MPU_ACCESS_BUFFERABLE) || \
+                                          ((STATE) == MPU_ACCESS_NOT_BUFFERABLE))
+
+#define IS_MPU_TEX_LEVEL(TYPE) (((TYPE) == MPU_TEX_LEVEL0)  || \
+                                ((TYPE) == MPU_TEX_LEVEL1)  || \
+                                ((TYPE) == MPU_TEX_LEVEL2))
+
+#define IS_MPU_REGION_PERMISSION_ATTRIBUTE(TYPE) (((TYPE) == MPU_REGION_NO_ACCESS)   || \
+                                                  ((TYPE) == MPU_REGION_PRIV_RW)     || \
+                                                  ((TYPE) == MPU_REGION_PRIV_RW_URO) || \
+                                                  ((TYPE) == MPU_REGION_FULL_ACCESS) || \
+                                                  ((TYPE) == MPU_REGION_PRIV_RO)     || \
+                                                  ((TYPE) == MPU_REGION_PRIV_RO_URO))
+
+#define IS_MPU_REGION_NUMBER(NUMBER)    (((NUMBER) == MPU_REGION_NUMBER0) || \
+                                         ((NUMBER) == MPU_REGION_NUMBER1) || \
+                                         ((NUMBER) == MPU_REGION_NUMBER2) || \
+                                         ((NUMBER) == MPU_REGION_NUMBER3) || \
+                                         ((NUMBER) == MPU_REGION_NUMBER4) || \
+                                         ((NUMBER) == MPU_REGION_NUMBER5) || \
+                                         ((NUMBER) == MPU_REGION_NUMBER6) || \
+                                         ((NUMBER) == MPU_REGION_NUMBER7))
+
+#define IS_MPU_REGION_SIZE(SIZE)    (((SIZE) == MPU_REGION_SIZE_32B)   || \
+                                     ((SIZE) == MPU_REGION_SIZE_64B)   || \
+                                     ((SIZE) == MPU_REGION_SIZE_128B)  || \
+                                     ((SIZE) == MPU_REGION_SIZE_256B)  || \
+                                     ((SIZE) == MPU_REGION_SIZE_512B)  || \
+                                     ((SIZE) == MPU_REGION_SIZE_1KB)   || \
+                                     ((SIZE) == MPU_REGION_SIZE_2KB)   || \
+                                     ((SIZE) == MPU_REGION_SIZE_4KB)   || \
+                                     ((SIZE) == MPU_REGION_SIZE_8KB)   || \
+                                     ((SIZE) == MPU_REGION_SIZE_16KB)  || \
+                                     ((SIZE) == MPU_REGION_SIZE_32KB)  || \
+                                     ((SIZE) == MPU_REGION_SIZE_64KB)  || \
+                                     ((SIZE) == MPU_REGION_SIZE_128KB) || \
+                                     ((SIZE) == MPU_REGION_SIZE_256KB) || \
+                                     ((SIZE) == MPU_REGION_SIZE_512KB) || \
+                                     ((SIZE) == MPU_REGION_SIZE_1MB)   || \
+                                     ((SIZE) == MPU_REGION_SIZE_2MB)   || \
+                                     ((SIZE) == MPU_REGION_SIZE_4MB)   || \
+                                     ((SIZE) == MPU_REGION_SIZE_8MB)   || \
+                                     ((SIZE) == MPU_REGION_SIZE_16MB)  || \
+                                     ((SIZE) == MPU_REGION_SIZE_32MB)  || \
+                                     ((SIZE) == MPU_REGION_SIZE_64MB)  || \
+                                     ((SIZE) == MPU_REGION_SIZE_128MB) || \
+                                     ((SIZE) == MPU_REGION_SIZE_256MB) || \
+                                     ((SIZE) == MPU_REGION_SIZE_512MB) || \
+                                     ((SIZE) == MPU_REGION_SIZE_1GB)   || \
+                                     ((SIZE) == MPU_REGION_SIZE_2GB)   || \
+                                     ((SIZE) == MPU_REGION_SIZE_4GB))
+
+#define IS_MPU_SUB_REGION_DISABLE(SUBREGION)  ((SUBREGION) < (uint16_t)0x00FF)
+#endif /* __MPU_PRESENT */
+
+/**                                                                          
+  * @}                                                                  
+  */
+
+/* Private functions ---------------------------------------------------------*/
+
+/**
+  * @}
+  */ 
+
+/**
+  * @}
+  */
+  
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F1xx_HAL_CORTEX_H */
+ 
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_crc.h

@@ -0,0 +1,184 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_hal_crc.h
+  * @author  MCD Application Team
+  * @brief   Header file of CRC HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef STM32F1xx_HAL_CRC_H
+#define STM32F1xx_HAL_CRC_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_hal_def.h"
+
+/** @addtogroup STM32F1xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup CRC
+  * @{
+  */
+
+/* Exported types ------------------------------------------------------------*/
+/** @defgroup CRC_Exported_Types CRC Exported Types
+  * @{
+  */
+
+/**
+  * @brief  CRC HAL State Structure definition
+  */
+typedef enum
+{
+  HAL_CRC_STATE_RESET     = 0x00U,  /*!< CRC not yet initialized or disabled */
+  HAL_CRC_STATE_READY     = 0x01U,  /*!< CRC initialized and ready for use   */
+  HAL_CRC_STATE_BUSY      = 0x02U,  /*!< CRC internal process is ongoing     */
+  HAL_CRC_STATE_TIMEOUT   = 0x03U,  /*!< CRC timeout state                   */
+  HAL_CRC_STATE_ERROR     = 0x04U   /*!< CRC error state                     */
+} HAL_CRC_StateTypeDef;
+
+
+/**
+  * @brief  CRC Handle Structure definition
+  */
+typedef struct
+{
+  CRC_TypeDef                 *Instance;   /*!< Register base address        */
+
+  HAL_LockTypeDef             Lock;        /*!< CRC Locking object           */
+
+  __IO HAL_CRC_StateTypeDef   State;       /*!< CRC communication state      */
+
+} CRC_HandleTypeDef;
+/**
+  * @}
+  */
+
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup CRC_Exported_Constants CRC Exported Constants
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/* Exported macros -----------------------------------------------------------*/
+/** @defgroup CRC_Exported_Macros CRC Exported Macros
+  * @{
+  */
+
+/** @brief Reset CRC handle state.
+  * @param  __HANDLE__ CRC handle.
+  * @retval None
+  */
+#define __HAL_CRC_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_CRC_STATE_RESET)
+
+/**
+  * @brief  Reset CRC Data Register.
+  * @param  __HANDLE__ CRC handle
+  * @retval None
+  */
+#define __HAL_CRC_DR_RESET(__HANDLE__) ((__HANDLE__)->Instance->CR |= CRC_CR_RESET)
+
+/**
+  * @brief Store data in the Independent Data (ID) register.
+  * @param __HANDLE__ CRC handle
+  * @param __VALUE__  Value to be stored in the ID register
+  * @note  Refer to the Reference Manual to get the authorized __VALUE__ length in bits
+  * @retval None
+  */
+#define __HAL_CRC_SET_IDR(__HANDLE__, __VALUE__) (WRITE_REG((__HANDLE__)->Instance->IDR, (__VALUE__)))
+
+/**
+  * @brief Return the data stored in the Independent Data (ID) register.
+  * @param __HANDLE__ CRC handle
+  * @note  Refer to the Reference Manual to get the authorized __VALUE__ length in bits
+  * @retval Value of the ID register
+  */
+#define __HAL_CRC_GET_IDR(__HANDLE__) (((__HANDLE__)->Instance->IDR) & CRC_IDR_IDR)
+/**
+  * @}
+  */
+
+
+/* Private macros --------------------------------------------------------*/
+/** @defgroup  CRC_Private_Macros CRC Private Macros
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/* Exported functions --------------------------------------------------------*/
+/** @defgroup CRC_Exported_Functions CRC Exported Functions
+  * @{
+  */
+
+/* Initialization and de-initialization functions  ****************************/
+/** @defgroup CRC_Exported_Functions_Group1 Initialization and de-initialization functions
+  * @{
+  */
+HAL_StatusTypeDef HAL_CRC_Init(CRC_HandleTypeDef *hcrc);
+HAL_StatusTypeDef HAL_CRC_DeInit(CRC_HandleTypeDef *hcrc);
+void HAL_CRC_MspInit(CRC_HandleTypeDef *hcrc);
+void HAL_CRC_MspDeInit(CRC_HandleTypeDef *hcrc);
+/**
+  * @}
+  */
+
+/* Peripheral Control functions ***********************************************/
+/** @defgroup CRC_Exported_Functions_Group2 Peripheral Control functions
+  * @{
+  */
+uint32_t HAL_CRC_Accumulate(CRC_HandleTypeDef *hcrc, uint32_t pBuffer[], uint32_t BufferLength);
+uint32_t HAL_CRC_Calculate(CRC_HandleTypeDef *hcrc, uint32_t pBuffer[], uint32_t BufferLength);
+/**
+  * @}
+  */
+
+/* Peripheral State and Error functions ***************************************/
+/** @defgroup CRC_Exported_Functions_Group3 Peripheral State functions
+  * @{
+  */
+HAL_CRC_StateTypeDef HAL_CRC_GetState(CRC_HandleTypeDef *hcrc);
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* STM32F1xx_HAL_CRC_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_dac.h

@@ -0,0 +1,459 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_hal_dac.h
+  * @author  MCD Application Team
+  * @brief   Header file of DAC HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef STM32F1xx_HAL_DAC_H
+#define STM32F1xx_HAL_DAC_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/** @addtogroup STM32F1xx_HAL_Driver
+  * @{
+  */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_hal_def.h"
+
+#if defined(DAC)
+
+/** @addtogroup DAC
+  * @{
+  */
+
+/* Exported types ------------------------------------------------------------*/
+
+/** @defgroup DAC_Exported_Types DAC Exported Types
+  * @{
+  */
+
+/**
+  * @brief  HAL State structures definition
+  */
+typedef enum
+{
+  HAL_DAC_STATE_RESET             = 0x00U,  /*!< DAC not yet initialized or disabled  */
+  HAL_DAC_STATE_READY             = 0x01U,  /*!< DAC initialized and ready for use    */
+  HAL_DAC_STATE_BUSY              = 0x02U,  /*!< DAC internal processing is ongoing   */
+  HAL_DAC_STATE_TIMEOUT           = 0x03U,  /*!< DAC timeout state                    */
+  HAL_DAC_STATE_ERROR             = 0x04U   /*!< DAC error state                      */
+
+} HAL_DAC_StateTypeDef;
+
+/**
+  * @brief  DAC handle Structure definition
+  */
+#if (USE_HAL_DAC_REGISTER_CALLBACKS == 1)
+typedef struct __DAC_HandleTypeDef
+#else
+typedef struct
+#endif /* USE_HAL_DAC_REGISTER_CALLBACKS */
+{
+  DAC_TypeDef                 *Instance;     /*!< Register base address             */
+
+  __IO HAL_DAC_StateTypeDef   State;         /*!< DAC communication state           */
+
+  HAL_LockTypeDef             Lock;          /*!< DAC locking object                */
+
+  DMA_HandleTypeDef           *DMA_Handle1;  /*!< Pointer DMA handler for channel 1 */
+
+  DMA_HandleTypeDef           *DMA_Handle2;  /*!< Pointer DMA handler for channel 2 */
+
+  __IO uint32_t               ErrorCode;     /*!< DAC Error code                    */
+
+#if (USE_HAL_DAC_REGISTER_CALLBACKS == 1)
+  void (* ConvCpltCallbackCh1)            (struct __DAC_HandleTypeDef *hdac);
+  void (* ConvHalfCpltCallbackCh1)        (struct __DAC_HandleTypeDef *hdac);
+  void (* ErrorCallbackCh1)               (struct __DAC_HandleTypeDef *hdac);
+  void (* DMAUnderrunCallbackCh1)         (struct __DAC_HandleTypeDef *hdac);
+
+  void (* ConvCpltCallbackCh2)            (struct __DAC_HandleTypeDef *hdac);
+  void (* ConvHalfCpltCallbackCh2)        (struct __DAC_HandleTypeDef *hdac);
+  void (* ErrorCallbackCh2)               (struct __DAC_HandleTypeDef *hdac);
+  void (* DMAUnderrunCallbackCh2)         (struct __DAC_HandleTypeDef *hdac);
+
+
+  void (* MspInitCallback)                (struct __DAC_HandleTypeDef *hdac);
+  void (* MspDeInitCallback)              (struct __DAC_HandleTypeDef *hdac);
+#endif /* USE_HAL_DAC_REGISTER_CALLBACKS */
+
+} DAC_HandleTypeDef;
+
+/**
+  * @brief   DAC Configuration regular Channel structure definition
+  */
+typedef struct
+{
+  uint32_t DAC_Trigger;                  /*!< Specifies the external trigger for the selected DAC channel.
+                                              This parameter can be a value of @ref DAC_trigger_selection */
+
+  uint32_t DAC_OutputBuffer;             /*!< Specifies whether the DAC channel output buffer is enabled or disabled.
+                                               This parameter can be a value of @ref DAC_output_buffer */
+
+} DAC_ChannelConfTypeDef;
+
+#if (USE_HAL_DAC_REGISTER_CALLBACKS == 1)
+/**
+  * @brief  HAL DAC Callback ID enumeration definition
+  */
+typedef enum
+{
+  HAL_DAC_CH1_COMPLETE_CB_ID                 = 0x00U,  /*!< DAC CH1 Complete Callback ID      */
+  HAL_DAC_CH1_HALF_COMPLETE_CB_ID            = 0x01U,  /*!< DAC CH1 half Complete Callback ID */
+  HAL_DAC_CH1_ERROR_ID                       = 0x02U,  /*!< DAC CH1 error Callback ID         */
+  HAL_DAC_CH1_UNDERRUN_CB_ID                 = 0x03U,  /*!< DAC CH1 underrun Callback ID      */
+
+  HAL_DAC_CH2_COMPLETE_CB_ID                 = 0x04U,  /*!< DAC CH2 Complete Callback ID      */
+  HAL_DAC_CH2_HALF_COMPLETE_CB_ID            = 0x05U,  /*!< DAC CH2 half Complete Callback ID */
+  HAL_DAC_CH2_ERROR_ID                       = 0x06U,  /*!< DAC CH2 error Callback ID         */
+  HAL_DAC_CH2_UNDERRUN_CB_ID                 = 0x07U,  /*!< DAC CH2 underrun Callback ID      */
+
+  HAL_DAC_MSPINIT_CB_ID                      = 0x08U,  /*!< DAC MspInit Callback ID           */
+  HAL_DAC_MSPDEINIT_CB_ID                    = 0x09U,  /*!< DAC MspDeInit Callback ID         */
+  HAL_DAC_ALL_CB_ID                          = 0x0AU   /*!< DAC All ID                        */
+} HAL_DAC_CallbackIDTypeDef;
+
+/**
+  * @brief  HAL DAC Callback pointer definition
+  */
+typedef void (*pDAC_CallbackTypeDef)(DAC_HandleTypeDef *hdac);
+#endif /* USE_HAL_DAC_REGISTER_CALLBACKS */
+
+/**
+  * @}
+  */
+
+/* Exported constants --------------------------------------------------------*/
+
+/** @defgroup DAC_Exported_Constants DAC Exported Constants
+  * @{
+  */
+
+/** @defgroup DAC_Error_Code DAC Error Code
+  * @{
+  */
+#define  HAL_DAC_ERROR_NONE              0x00U    /*!< No error                          */
+#define  HAL_DAC_ERROR_DMAUNDERRUNCH1    0x01U    /*!< DAC channel1 DMA underrun error   */
+#define  HAL_DAC_ERROR_DMAUNDERRUNCH2    0x02U    /*!< DAC channel2 DMA underrun error   */
+#define  HAL_DAC_ERROR_DMA               0x04U    /*!< DMA error                         */
+#define  HAL_DAC_ERROR_TIMEOUT           0x08U    /*!< Timeout error                     */
+#if (USE_HAL_DAC_REGISTER_CALLBACKS == 1)
+#define HAL_DAC_ERROR_INVALID_CALLBACK   0x10U    /*!< Invalid callback error            */
+#endif /* USE_HAL_DAC_REGISTER_CALLBACKS */
+
+/**
+  * @}
+  */
+
+/** @defgroup DAC_output_buffer DAC output buffer
+  * @{
+  */
+#define DAC_OUTPUTBUFFER_ENABLE            0x00000000U
+#define DAC_OUTPUTBUFFER_DISABLE           (DAC_CR_BOFF1)
+
+/**
+  * @}
+  */
+
+/** @defgroup DAC_Channel_selection DAC Channel selection
+  * @{
+  */
+#define DAC_CHANNEL_1                      0x00000000U
+
+#define DAC_CHANNEL_2                      0x00000010U
+
+/**
+  * @}
+  */
+
+/** @defgroup DAC_data_alignment DAC data alignment
+  * @{
+  */
+#define DAC_ALIGN_12B_R                    0x00000000U
+#define DAC_ALIGN_12B_L                    0x00000004U
+#define DAC_ALIGN_8B_R                     0x00000008U
+
+/**
+  * @}
+  */
+
+/** @defgroup DAC_flags_definition DAC flags definition
+  * @{
+  */
+#define DAC_FLAG_DMAUDR1                   (DAC_SR_DMAUDR1)
+
+#define DAC_FLAG_DMAUDR2                   (DAC_SR_DMAUDR2)
+
+
+/**
+  * @}
+  */
+
+/** @defgroup DAC_IT_definition  DAC IT definition
+  * @{
+  */
+#define DAC_IT_DMAUDR1                   (DAC_SR_DMAUDR1)
+
+#define DAC_IT_DMAUDR2                   (DAC_SR_DMAUDR2)
+
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Exported macro ------------------------------------------------------------*/
+
+/** @defgroup DAC_Exported_Macros DAC Exported Macros
+  * @{
+  */
+
+/** @brief Reset DAC handle state.
+  * @param  __HANDLE__ specifies the DAC handle.
+  * @retval None
+  */
+#if (USE_HAL_DAC_REGISTER_CALLBACKS == 1)
+#define __HAL_DAC_RESET_HANDLE_STATE(__HANDLE__) do {                                                        \
+                                                      (__HANDLE__)->State             = HAL_DAC_STATE_RESET; \
+                                                      (__HANDLE__)->MspInitCallback   = NULL;                \
+                                                      (__HANDLE__)->MspDeInitCallback = NULL;                \
+                                                     } while(0)
+#else
+#define __HAL_DAC_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_DAC_STATE_RESET)
+#endif /* USE_HAL_DAC_REGISTER_CALLBACKS */
+
+/** @brief Enable the DAC channel.
+  * @param  __HANDLE__ specifies the DAC handle.
+  * @param  __DAC_Channel__ specifies the DAC channel
+  * @retval None
+  */
+#define __HAL_DAC_ENABLE(__HANDLE__, __DAC_Channel__) \
+  ((__HANDLE__)->Instance->CR |=  (DAC_CR_EN1 << ((__DAC_Channel__) & 0x10UL)))
+
+/** @brief Disable the DAC channel.
+  * @param  __HANDLE__ specifies the DAC handle
+  * @param  __DAC_Channel__ specifies the DAC channel.
+  * @retval None
+  */
+#define __HAL_DAC_DISABLE(__HANDLE__, __DAC_Channel__) \
+  ((__HANDLE__)->Instance->CR &=  ~(DAC_CR_EN1 << ((__DAC_Channel__) & 0x10UL)))
+
+/** @brief Set DHR12R1 alignment.
+  * @param  __ALIGNMENT__ specifies the DAC alignment
+  * @retval None
+  */
+#define DAC_DHR12R1_ALIGNMENT(__ALIGNMENT__) (0x00000008UL + (__ALIGNMENT__))
+
+
+/** @brief  Set DHR12R2 alignment.
+  * @param  __ALIGNMENT__ specifies the DAC alignment
+  * @retval None
+  */
+#define DAC_DHR12R2_ALIGNMENT(__ALIGNMENT__) (0x00000014UL + (__ALIGNMENT__))
+
+
+/** @brief  Set DHR12RD alignment.
+  * @param  __ALIGNMENT__ specifies the DAC alignment
+  * @retval None
+  */
+#define DAC_DHR12RD_ALIGNMENT(__ALIGNMENT__) (0x00000020UL + (__ALIGNMENT__))
+
+/** @brief Enable the DAC interrupt.
+  * @param  __HANDLE__ specifies the DAC handle
+  * @param  __INTERRUPT__ specifies the DAC interrupt.
+  *          This parameter can be any combination of the following values:
+  *            @arg DAC_IT_DMAUDR1 DAC channel 1 DMA underrun interrupt
+  *            @arg DAC_IT_DMAUDR2 DAC channel 2 DMA underrun interrupt
+  * @retval None
+  */
+#define __HAL_DAC_ENABLE_IT(__HANDLE__, __INTERRUPT__) (((__HANDLE__)->Instance->CR) |= (__INTERRUPT__))
+
+/** @brief Disable the DAC interrupt.
+  * @param  __HANDLE__ specifies the DAC handle
+  * @param  __INTERRUPT__ specifies the DAC interrupt.
+  *          This parameter can be any combination of the following values:
+  *            @arg DAC_IT_DMAUDR1 DAC channel 1 DMA underrun interrupt
+  *            @arg DAC_IT_DMAUDR2 DAC channel 2 DMA underrun interrupt
+  * @retval None
+  */
+#define __HAL_DAC_DISABLE_IT(__HANDLE__, __INTERRUPT__) (((__HANDLE__)->Instance->CR) &= ~(__INTERRUPT__))
+
+/** @brief  Check whether the specified DAC interrupt source is enabled or not.
+  * @param __HANDLE__ DAC handle
+  * @param __INTERRUPT__ DAC interrupt source to check
+  *          This parameter can be any combination of the following values:
+  *            @arg DAC_IT_DMAUDR1 DAC channel 1 DMA underrun interrupt
+  *            @arg DAC_IT_DMAUDR2 DAC channel 2 DMA underrun interrupt
+  * @retval State of interruption (SET or RESET)
+  */
+#define __HAL_DAC_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__) (((__HANDLE__)->Instance->CR\
+                                                             & (__INTERRUPT__)) == (__INTERRUPT__))
+
+/** @brief  Get the selected DAC's flag status.
+  * @param  __HANDLE__ specifies the DAC handle.
+  * @param  __FLAG__ specifies the DAC flag to get.
+  *          This parameter can be any combination of the following values:
+  *            @arg DAC_FLAG_DMAUDR1 DAC channel 1 DMA underrun flag
+  *            @arg DAC_FLAG_DMAUDR2 DAC channel 2 DMA underrun flag
+  * @retval None
+  */
+#define __HAL_DAC_GET_FLAG(__HANDLE__, __FLAG__) ((((__HANDLE__)->Instance->SR) & (__FLAG__)) == (__FLAG__))
+
+/** @brief  Clear the DAC's flag.
+  * @param  __HANDLE__ specifies the DAC handle.
+  * @param  __FLAG__ specifies the DAC flag to clear.
+  *          This parameter can be any combination of the following values:
+  *            @arg DAC_FLAG_DMAUDR1 DAC channel 1 DMA underrun flag
+  *            @arg DAC_FLAG_DMAUDR2 DAC channel 2 DMA underrun flag
+  * @retval None
+  */
+#define __HAL_DAC_CLEAR_FLAG(__HANDLE__, __FLAG__) (((__HANDLE__)->Instance->SR) = (__FLAG__))
+
+/**
+  * @}
+  */
+
+/* Private macro -------------------------------------------------------------*/
+
+/** @defgroup DAC_Private_Macros DAC Private Macros
+  * @{
+  */
+#define IS_DAC_OUTPUT_BUFFER_STATE(STATE) (((STATE) == DAC_OUTPUTBUFFER_ENABLE) || \
+                                           ((STATE) == DAC_OUTPUTBUFFER_DISABLE))
+
+#define IS_DAC_CHANNEL(CHANNEL) (((CHANNEL) == DAC_CHANNEL_1) || \
+                                 ((CHANNEL) == DAC_CHANNEL_2))
+
+#define IS_DAC_ALIGN(ALIGN) (((ALIGN) == DAC_ALIGN_12B_R) || \
+                             ((ALIGN) == DAC_ALIGN_12B_L) || \
+                             ((ALIGN) == DAC_ALIGN_8B_R))
+
+#define IS_DAC_DATA(DATA) ((DATA) <= 0xFFF0UL)
+
+/**
+  * @}
+  */
+
+/* Include DAC HAL Extended module */
+#include "stm32f1xx_hal_dac_ex.h"
+
+/* Exported functions --------------------------------------------------------*/
+
+/** @addtogroup DAC_Exported_Functions
+  * @{
+  */
+
+/** @addtogroup DAC_Exported_Functions_Group1
+  * @{
+  */
+/* Initialization and de-initialization functions *****************************/
+HAL_StatusTypeDef HAL_DAC_Init(DAC_HandleTypeDef *hdac);
+HAL_StatusTypeDef HAL_DAC_DeInit(DAC_HandleTypeDef *hdac);
+void HAL_DAC_MspInit(DAC_HandleTypeDef *hdac);
+void HAL_DAC_MspDeInit(DAC_HandleTypeDef *hdac);
+
+/**
+  * @}
+  */
+
+/** @addtogroup DAC_Exported_Functions_Group2
+  * @{
+  */
+/* IO operation functions *****************************************************/
+HAL_StatusTypeDef HAL_DAC_Start(DAC_HandleTypeDef *hdac, uint32_t Channel);
+HAL_StatusTypeDef HAL_DAC_Stop(DAC_HandleTypeDef *hdac, uint32_t Channel);
+HAL_StatusTypeDef HAL_DAC_Start_DMA(DAC_HandleTypeDef *hdac, uint32_t Channel, uint32_t *pData, uint32_t Length,
+                                    uint32_t Alignment);
+HAL_StatusTypeDef HAL_DAC_Stop_DMA(DAC_HandleTypeDef *hdac, uint32_t Channel);
+void HAL_DAC_IRQHandler(DAC_HandleTypeDef *hdac);
+HAL_StatusTypeDef HAL_DAC_SetValue(DAC_HandleTypeDef *hdac, uint32_t Channel, uint32_t Alignment, uint32_t Data);
+
+void HAL_DAC_ConvCpltCallbackCh1(DAC_HandleTypeDef *hdac);
+void HAL_DAC_ConvHalfCpltCallbackCh1(DAC_HandleTypeDef *hdac);
+void HAL_DAC_ErrorCallbackCh1(DAC_HandleTypeDef *hdac);
+void HAL_DAC_DMAUnderrunCallbackCh1(DAC_HandleTypeDef *hdac);
+
+#if (USE_HAL_DAC_REGISTER_CALLBACKS == 1)
+/* DAC callback registering/unregistering */
+HAL_StatusTypeDef     HAL_DAC_RegisterCallback(DAC_HandleTypeDef *hdac, HAL_DAC_CallbackIDTypeDef CallbackID,
+                                               pDAC_CallbackTypeDef pCallback);
+HAL_StatusTypeDef     HAL_DAC_UnRegisterCallback(DAC_HandleTypeDef *hdac, HAL_DAC_CallbackIDTypeDef CallbackID);
+#endif /* USE_HAL_DAC_REGISTER_CALLBACKS */
+
+/**
+  * @}
+  */
+
+/** @addtogroup DAC_Exported_Functions_Group3
+  * @{
+  */
+/* Peripheral Control functions ***********************************************/
+uint32_t HAL_DAC_GetValue(DAC_HandleTypeDef *hdac, uint32_t Channel);
+HAL_StatusTypeDef HAL_DAC_ConfigChannel(DAC_HandleTypeDef *hdac, DAC_ChannelConfTypeDef *sConfig, uint32_t Channel);
+/**
+  * @}
+  */
+
+/** @addtogroup DAC_Exported_Functions_Group4
+  * @{
+  */
+/* Peripheral State and Error functions ***************************************/
+HAL_DAC_StateTypeDef HAL_DAC_GetState(DAC_HandleTypeDef *hdac);
+uint32_t HAL_DAC_GetError(DAC_HandleTypeDef *hdac);
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup DAC_Private_Functions DAC Private Functions
+  * @{
+  */
+void DAC_DMAConvCpltCh1(DMA_HandleTypeDef *hdma);
+void DAC_DMAErrorCh1(DMA_HandleTypeDef *hdma);
+void DAC_DMAHalfConvCpltCh1(DMA_HandleTypeDef *hdma);
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#endif /* DAC */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+
+#endif /* STM32F1xx_HAL_DAC_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_dac_ex.h

@@ -0,0 +1,278 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_hal_dac_ex.h
+  * @author  MCD Application Team
+  * @brief   Header file of DAC HAL Extended module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef STM32F1xx_HAL_DAC_EX_H
+#define STM32F1xx_HAL_DAC_EX_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/** @addtogroup STM32F1xx_HAL_Driver
+  * @{
+  */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_hal_def.h"
+
+#if defined(DAC)
+
+/** @addtogroup DACEx
+  * @{
+  */
+
+/* Exported types ------------------------------------------------------------*/
+
+/**
+  * @brief  HAL State structures definition
+  */
+
+/* Exported constants --------------------------------------------------------*/
+
+/** @defgroup DACEx_Exported_Constants DACEx Exported Constants
+  * @{
+  */
+
+/** @defgroup DACEx_lfsrunmask_triangleamplitude DACEx lfsrunmask triangle amplitude
+  * @{
+  */
+#define DAC_LFSRUNMASK_BIT0                0x00000000UL                                                        /*!< Unmask DAC channel LFSR bit0 for noise wave generation */
+#define DAC_LFSRUNMASK_BITS1_0             (                                                   DAC_CR_MAMP1_0) /*!< Unmask DAC channel LFSR bit[1:0] for noise wave generation */
+#define DAC_LFSRUNMASK_BITS2_0             (                                  DAC_CR_MAMP1_1                 ) /*!< Unmask DAC channel LFSR bit[2:0] for noise wave generation */
+#define DAC_LFSRUNMASK_BITS3_0             (                                  DAC_CR_MAMP1_1 | DAC_CR_MAMP1_0) /*!< Unmask DAC channel LFSR bit[3:0] for noise wave generation */
+#define DAC_LFSRUNMASK_BITS4_0             (                 DAC_CR_MAMP1_2                                  ) /*!< Unmask DAC channel LFSR bit[4:0] for noise wave generation */
+#define DAC_LFSRUNMASK_BITS5_0             (                 DAC_CR_MAMP1_2                  | DAC_CR_MAMP1_0) /*!< Unmask DAC channel LFSR bit[5:0] for noise wave generation */
+#define DAC_LFSRUNMASK_BITS6_0             (                 DAC_CR_MAMP1_2 | DAC_CR_MAMP1_1                 ) /*!< Unmask DAC channel LFSR bit[6:0] for noise wave generation */
+#define DAC_LFSRUNMASK_BITS7_0             (                 DAC_CR_MAMP1_2 | DAC_CR_MAMP1_1 | DAC_CR_MAMP1_0) /*!< Unmask DAC channel LFSR bit[7:0] for noise wave generation */
+#define DAC_LFSRUNMASK_BITS8_0             (DAC_CR_MAMP1_3                                                   ) /*!< Unmask DAC channel LFSR bit[8:0] for noise wave generation */
+#define DAC_LFSRUNMASK_BITS9_0             (DAC_CR_MAMP1_3                                   | DAC_CR_MAMP1_0) /*!< Unmask DAC channel LFSR bit[9:0] for noise wave generation */
+#define DAC_LFSRUNMASK_BITS10_0            (DAC_CR_MAMP1_3                  | DAC_CR_MAMP1_1                 ) /*!< Unmask DAC channel LFSR bit[10:0] for noise wave generation */
+#define DAC_LFSRUNMASK_BITS11_0            (DAC_CR_MAMP1_3                  | DAC_CR_MAMP1_1 | DAC_CR_MAMP1_0) /*!< Unmask DAC channel LFSR bit[11:0] for noise wave generation */
+#define DAC_TRIANGLEAMPLITUDE_1            0x00000000UL                                                        /*!< Select max triangle amplitude of 1 */
+#define DAC_TRIANGLEAMPLITUDE_3            (                                                   DAC_CR_MAMP1_0) /*!< Select max triangle amplitude of 3 */
+#define DAC_TRIANGLEAMPLITUDE_7            (                                  DAC_CR_MAMP1_1                 ) /*!< Select max triangle amplitude of 7 */
+#define DAC_TRIANGLEAMPLITUDE_15           (                                  DAC_CR_MAMP1_1 | DAC_CR_MAMP1_0) /*!< Select max triangle amplitude of 15 */
+#define DAC_TRIANGLEAMPLITUDE_31           (                 DAC_CR_MAMP1_2                                  ) /*!< Select max triangle amplitude of 31 */
+#define DAC_TRIANGLEAMPLITUDE_63           (                 DAC_CR_MAMP1_2                  | DAC_CR_MAMP1_0) /*!< Select max triangle amplitude of 63 */
+#define DAC_TRIANGLEAMPLITUDE_127          (                 DAC_CR_MAMP1_2 | DAC_CR_MAMP1_1                 ) /*!< Select max triangle amplitude of 127 */
+#define DAC_TRIANGLEAMPLITUDE_255          (                 DAC_CR_MAMP1_2 | DAC_CR_MAMP1_1 | DAC_CR_MAMP1_0) /*!< Select max triangle amplitude of 255 */
+#define DAC_TRIANGLEAMPLITUDE_511          (DAC_CR_MAMP1_3                                                   ) /*!< Select max triangle amplitude of 511 */
+#define DAC_TRIANGLEAMPLITUDE_1023         (DAC_CR_MAMP1_3                                   | DAC_CR_MAMP1_0) /*!< Select max triangle amplitude of 1023 */
+#define DAC_TRIANGLEAMPLITUDE_2047         (DAC_CR_MAMP1_3                  | DAC_CR_MAMP1_1                 ) /*!< Select max triangle amplitude of 2047 */
+#define DAC_TRIANGLEAMPLITUDE_4095         (DAC_CR_MAMP1_3                  | DAC_CR_MAMP1_1 | DAC_CR_MAMP1_0) /*!< Select max triangle amplitude of 4095 */
+
+/**
+  * @}
+  */
+
+/** @defgroup DACEx_trigger_selection DAC trigger selection
+  * @{
+  */
+#define DAC_TRIGGER_NONE                   0x00000000U            /*!< Conversion is automatic once the DAC1_DHRxxxx register 
+                                                                       has been loaded, and not by external trigger */
+#define DAC_TRIGGER_T6_TRGO                ((uint32_t)                                                    DAC_CR_TEN1)  /*!< TIM6 TRGO selected as external conversion trigger for DAC channel */
+#define DAC_TRIGGER_T7_TRGO                ((uint32_t)(                 DAC_CR_TSEL1_1                  | DAC_CR_TEN1)) /*!< TIM7 TRGO selected as external conversion trigger for DAC channel */
+#define DAC_TRIGGER_T2_TRGO                ((uint32_t)(DAC_CR_TSEL1_2                                   | DAC_CR_TEN1)) /*!< TIM2 TRGO selected as external conversion trigger for DAC channel */
+#define DAC_TRIGGER_T4_TRGO                ((uint32_t)(DAC_CR_TSEL1_2                  | DAC_CR_TSEL1_0 | DAC_CR_TEN1)) /*!< TIM4 TRGO selected as external conversion trigger for DAC channel */
+#define DAC_TRIGGER_EXT_IT9                ((uint32_t)(DAC_CR_TSEL1_2 | DAC_CR_TSEL1_1                  | DAC_CR_TEN1)) /*!< EXTI Line9 event selected as external conversion trigger for DAC channel */
+#define DAC_TRIGGER_SOFTWARE               ((uint32_t)(DAC_CR_TSEL1                                     | DAC_CR_TEN1)) /*!< Conversion started by software trigger for DAC channel */
+
+#if defined (STM32F101xE) || defined (STM32F101xG) || defined (STM32F103xE) || defined (STM32F103xG)
+/* For STM32F10x high-density and XL-density devices: TIM8 */
+#define DAC_TRIGGER_T8_TRGO                ((uint32_t)                                   DAC_CR_TSEL1_0 | DAC_CR_TEN1)  /*!< TIM8 TRGO selected as external conversion trigger for DAC channel */
+#endif /* STM32F101xE || STM32F101xG || STM32F103xE || STM32F103xG */
+   
+#if defined (STM32F100xB) || defined (STM32F100xE) || defined (STM32F105xC) || defined (STM32F107xC)
+/* For STM32F10x connectivity line devices and STM32F100x devices: TIM3 */
+#define DAC_TRIGGER_T3_TRGO                ((uint32_t)                                   DAC_CR_TSEL1_0 | DAC_CR_TEN1)  /*!< TIM3 TRGO selected as external conversion trigger for DAC channel */
+#endif /* STM32F100xB || STM32F100xE || STM32F105xC || STM32F107xC */
+
+/* Availability of trigger from TIM5 and TIM15:                               */
+/*  - For STM32F10x value line devices STM32F100xB:                           */
+/*    trigger from TIM15 is available, TIM5 not available.                    */
+/*  - For STM32F10x value line devices STM32F100xE:                           */
+/*    trigger from TIM15 and TIM5 are both available,                         */
+/*    selection depends on remap (with TIM5 as default configuration).        */
+/*  - Other STM32F1 devices:                                                  */
+/*    trigger from TIM5 is available, TIM15 not  available.                   */
+#if defined (STM32F100xB)
+#define DAC_TRIGGER_T15_TRGO               ((uint32_t)(                 DAC_CR_TSEL1_1 | DAC_CR_TSEL1_0 | DAC_CR_TEN1)) /*!< TIM15 TRGO selected as external conversion trigger for DAC channel */
+#else
+
+#define DAC_TRIGGER_T5_TRGO                ((uint32_t)(                 DAC_CR_TSEL1_1 | DAC_CR_TSEL1_0 | DAC_CR_TEN1)) /*!< TIM5 TRGO selected as external conversion trigger for DAC channel */
+
+#if defined (STM32F100xE)
+/*!< DAC trigger availability depending on STM32F1 devices:
+     For STM32F100x high-density value line devices, the TIM15 TRGO event can be selected 
+     as replacement of TIM5 TRGO if the MISC_REMAP bit in the AFIO_MAPR2 register is set.
+     Refer to macro "__HAL_AFIO_REMAP_MISC_ENABLE()/__HAL_AFIO_REMAP_MISC_DISABLE()".
+     Otherwise, TIM5 TRGO is used and TIM15 TRGO is not used (default case).
+     For more details please refer to the AFIO section. */
+#define DAC_TRIGGER_T15_TRGO    DAC_TRIGGER_T5_TRGO
+#endif /* STM32F100xE */
+   
+#endif /* STM32F100xB */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Exported macro ------------------------------------------------------------*/
+
+
+/* Private macro -------------------------------------------------------------*/
+
+/** @defgroup DACEx_Private_Macros DACEx Private Macros
+  * @{
+  */
+#if defined (STM32F101xE) || defined (STM32F101xG) || defined (STM32F103xE) || defined (STM32F103xG)
+#define IS_DAC_TRIGGER(TRIGGER) (((TRIGGER) == DAC_TRIGGER_NONE)    || \
+                                 ((TRIGGER) == DAC_TRIGGER_T6_TRGO) || \
+                                 ((TRIGGER) == DAC_TRIGGER_T8_TRGO) || \
+                                 ((TRIGGER) == DAC_TRIGGER_T7_TRGO) || \
+                                 ((TRIGGER) == DAC_TRIGGER_T5_TRGO) || \
+                                 ((TRIGGER) == DAC_TRIGGER_T2_TRGO) || \
+                                 ((TRIGGER) == DAC_TRIGGER_T4_TRGO) || \
+                                 ((TRIGGER) == DAC_TRIGGER_EXT_IT9) || \
+                                 ((TRIGGER) == DAC_TRIGGER_SOFTWARE))
+#endif /* STM32F101xE || STM32F101xG || STM32F103xE || STM32F103xG */
+#if defined (STM32F100xE) || defined (STM32F105xC) || defined (STM32F107xC)
+#define IS_DAC_TRIGGER(TRIGGER) (((TRIGGER) == DAC_TRIGGER_NONE)    || \
+                                 ((TRIGGER) == DAC_TRIGGER_T6_TRGO) || \
+                                 ((TRIGGER) == DAC_TRIGGER_T3_TRGO) || \
+                                 ((TRIGGER) == DAC_TRIGGER_T7_TRGO) || \
+                                 ((TRIGGER) == DAC_TRIGGER_T5_TRGO) || \
+                                 ((TRIGGER) == DAC_TRIGGER_T2_TRGO) || \
+                                 ((TRIGGER) == DAC_TRIGGER_T4_TRGO) || \
+                                 ((TRIGGER) == DAC_TRIGGER_EXT_IT9) || \
+                                 ((TRIGGER) == DAC_TRIGGER_SOFTWARE))
+#endif /* STM32F100xE || STM32F105xC || STM32F107xC */
+#if defined (STM32F100xB)
+#define IS_DAC_TRIGGER(TRIGGER) (((TRIGGER) == DAC_TRIGGER_NONE)     || \
+                                 ((TRIGGER) == DAC_TRIGGER_T6_TRGO)  || \
+                                 ((TRIGGER) == DAC_TRIGGER_T3_TRGO)  || \
+                                 ((TRIGGER) == DAC_TRIGGER_T7_TRGO)  || \
+                                 ((TRIGGER) == DAC_TRIGGER_T15_TRGO) || \
+                                 ((TRIGGER) == DAC_TRIGGER_T2_TRGO)  || \
+                                 ((TRIGGER) == DAC_TRIGGER_T4_TRGO)  || \
+                                 ((TRIGGER) == DAC_TRIGGER_EXT_IT9)  || \
+                                 ((TRIGGER) == DAC_TRIGGER_SOFTWARE))
+#endif /* STM32F100xB */
+
+#define IS_DAC_LFSR_UNMASK_TRIANGLE_AMPLITUDE(VALUE) (((VALUE) == DAC_LFSRUNMASK_BIT0) || \
+                                                      ((VALUE) == DAC_LFSRUNMASK_BITS1_0) || \
+                                                      ((VALUE) == DAC_LFSRUNMASK_BITS2_0) || \
+                                                      ((VALUE) == DAC_LFSRUNMASK_BITS3_0) || \
+                                                      ((VALUE) == DAC_LFSRUNMASK_BITS4_0) || \
+                                                      ((VALUE) == DAC_LFSRUNMASK_BITS5_0) || \
+                                                      ((VALUE) == DAC_LFSRUNMASK_BITS6_0) || \
+                                                      ((VALUE) == DAC_LFSRUNMASK_BITS7_0) || \
+                                                      ((VALUE) == DAC_LFSRUNMASK_BITS8_0) || \
+                                                      ((VALUE) == DAC_LFSRUNMASK_BITS9_0) || \
+                                                      ((VALUE) == DAC_LFSRUNMASK_BITS10_0) || \
+                                                      ((VALUE) == DAC_LFSRUNMASK_BITS11_0) || \
+                                                      ((VALUE) == DAC_TRIANGLEAMPLITUDE_1) || \
+                                                      ((VALUE) == DAC_TRIANGLEAMPLITUDE_3) || \
+                                                      ((VALUE) == DAC_TRIANGLEAMPLITUDE_7) || \
+                                                      ((VALUE) == DAC_TRIANGLEAMPLITUDE_15) || \
+                                                      ((VALUE) == DAC_TRIANGLEAMPLITUDE_31) || \
+                                                      ((VALUE) == DAC_TRIANGLEAMPLITUDE_63) || \
+                                                      ((VALUE) == DAC_TRIANGLEAMPLITUDE_127) || \
+                                                      ((VALUE) == DAC_TRIANGLEAMPLITUDE_255) || \
+                                                      ((VALUE) == DAC_TRIANGLEAMPLITUDE_511) || \
+                                                      ((VALUE) == DAC_TRIANGLEAMPLITUDE_1023) || \
+                                                      ((VALUE) == DAC_TRIANGLEAMPLITUDE_2047) || \
+                                                      ((VALUE) == DAC_TRIANGLEAMPLITUDE_4095))
+/**
+  * @}
+  */
+
+/* Exported functions --------------------------------------------------------*/
+/* Extended features functions ***********************************************/
+
+/** @addtogroup DACEx_Exported_Functions
+  * @{
+  */
+
+/** @addtogroup DACEx_Exported_Functions_Group2
+  * @{
+  */
+/* IO operation functions *****************************************************/
+
+HAL_StatusTypeDef HAL_DACEx_TriangleWaveGenerate(DAC_HandleTypeDef *hdac, uint32_t Channel, uint32_t Amplitude);
+HAL_StatusTypeDef HAL_DACEx_NoiseWaveGenerate(DAC_HandleTypeDef *hdac, uint32_t Channel, uint32_t Amplitude);
+
+HAL_StatusTypeDef HAL_DACEx_DualStart(DAC_HandleTypeDef *hdac);
+HAL_StatusTypeDef HAL_DACEx_DualStop(DAC_HandleTypeDef *hdac);
+HAL_StatusTypeDef HAL_DACEx_DualSetValue(DAC_HandleTypeDef *hdac, uint32_t Alignment, uint32_t Data1, uint32_t Data2);
+uint32_t HAL_DACEx_DualGetValue(DAC_HandleTypeDef *hdac);
+
+void HAL_DACEx_ConvCpltCallbackCh2(DAC_HandleTypeDef *hdac);
+void HAL_DACEx_ConvHalfCpltCallbackCh2(DAC_HandleTypeDef *hdac);
+void HAL_DACEx_ErrorCallbackCh2(DAC_HandleTypeDef *hdac);
+void HAL_DACEx_DMAUnderrunCallbackCh2(DAC_HandleTypeDef *hdac);
+
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/** @addtogroup DACEx_Private_Functions
+  * @{
+  */
+
+/* DAC_DMAConvCpltCh2 / DAC_DMAErrorCh2 / DAC_DMAHalfConvCpltCh2 */
+/* are called by HAL_DAC_Start_DMA */
+void DAC_DMAConvCpltCh2(DMA_HandleTypeDef *hdma);
+void DAC_DMAErrorCh2(DMA_HandleTypeDef *hdma);
+void DAC_DMAHalfConvCpltCh2(DMA_HandleTypeDef *hdma);
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#endif /* DAC */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* STM32F1xx_HAL_DAC_EX_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_def.h

@@ -0,0 +1,210 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_hal_def.h
+  * @author  MCD Application Team
+  * @brief   This file contains HAL common defines, enumeration, macros and
+  *          structures definitions.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2017 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F1xx_HAL_DEF
+#define __STM32F1xx_HAL_DEF
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx.h"
+#include "Legacy/stm32_hal_legacy.h"
+#include <stddef.h>
+
+/* Exported types ------------------------------------------------------------*/
+
+/**
+  * @brief  HAL Status structures definition
+  */
+typedef enum
+{
+  HAL_OK       = 0x00U,
+  HAL_ERROR    = 0x01U,
+  HAL_BUSY     = 0x02U,
+  HAL_TIMEOUT  = 0x03U
+} HAL_StatusTypeDef;
+
+/**
+  * @brief  HAL Lock structures definition
+  */
+typedef enum
+{
+  HAL_UNLOCKED = 0x00U,
+  HAL_LOCKED   = 0x01U
+} HAL_LockTypeDef;
+
+/* Exported macro ------------------------------------------------------------*/
+#define HAL_MAX_DELAY      0xFFFFFFFFU
+
+#define HAL_IS_BIT_SET(REG, BIT)         (((REG) & (BIT)) != 0U)
+#define HAL_IS_BIT_CLR(REG, BIT)         (((REG) & (BIT)) == 0U)
+
+#define __HAL_LINKDMA(__HANDLE__, __PPP_DMA_FIELD__, __DMA_HANDLE__)               \
+                        do{                                                      \
+                              (__HANDLE__)->__PPP_DMA_FIELD__ = &(__DMA_HANDLE__); \
+                              (__DMA_HANDLE__).Parent = (__HANDLE__);             \
+                          } while(0U)
+
+#define UNUSED(X) (void)X      /* To avoid gcc/g++ warnings */
+
+/** @brief Reset the Handle's State field.
+  * @param __HANDLE__ specifies the Peripheral Handle.
+  * @note  This macro can be used for the following purpose:
+  *          - When the Handle is declared as local variable; before passing it as parameter
+  *            to HAL_PPP_Init() for the first time, it is mandatory to use this macro
+  *            to set to 0 the Handle's "State" field.
+  *            Otherwise, "State" field may have any random value and the first time the function
+  *            HAL_PPP_Init() is called, the low level hardware initialization will be missed
+  *            (i.e. HAL_PPP_MspInit() will not be executed).
+  *          - When there is a need to reconfigure the low level hardware: instead of calling
+  *            HAL_PPP_DeInit() then HAL_PPP_Init(), user can make a call to this macro then HAL_PPP_Init().
+  *            In this later function, when the Handle's "State" field is set to 0, it will execute the function
+  *            HAL_PPP_MspInit() which will reconfigure the low level hardware.
+  * @retval None
+  */
+#define __HAL_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = 0U)
+
+#if (USE_RTOS == 1U)
+/* Reserved for future use */
+#error "USE_RTOS should be 0 in the current HAL release"
+#else
+#define __HAL_LOCK(__HANDLE__)                                           \
+                                do{                                        \
+                                    if((__HANDLE__)->Lock == HAL_LOCKED)   \
+                                    {                                      \
+                                       return HAL_BUSY;                    \
+                                    }                                      \
+                                    else                                   \
+                                    {                                      \
+                                       (__HANDLE__)->Lock = HAL_LOCKED;    \
+                                    }                                      \
+                                  }while (0U)
+
+#define __HAL_UNLOCK(__HANDLE__)                                          \
+                                  do{                                       \
+                                      (__HANDLE__)->Lock = HAL_UNLOCKED;    \
+                                    }while (0U)
+#endif /* USE_RTOS */
+
+#if defined (__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) /* ARM Compiler V6 */
+#ifndef __weak
+#define __weak  __attribute__((weak))
+#endif
+#ifndef __packed
+#define __packed  __attribute__((packed))
+#endif
+#elif defined ( __GNUC__ ) && !defined (__CC_ARM) /* GNU Compiler */
+#ifndef __weak
+#define __weak   __attribute__((weak))
+#endif /* __weak */
+#ifndef __packed
+#define __packed __attribute__((__packed__))
+#endif /* __packed */
+#endif /* __GNUC__ */
+
+
+/* Macro to get variable aligned on 4-bytes, for __ICCARM__ the directive "#pragma data_alignment=4" must be used instead */
+#if defined (__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050) /* ARM Compiler V6 */
+#ifndef __ALIGN_BEGIN
+#define __ALIGN_BEGIN
+#endif
+#ifndef __ALIGN_END
+#define __ALIGN_END      __attribute__ ((aligned (4)))
+#endif
+#elif defined ( __GNUC__ ) && !defined (__CC_ARM) /* GNU Compiler */
+#ifndef __ALIGN_END
+#define __ALIGN_END    __attribute__ ((aligned (4)))
+#endif /* __ALIGN_END */
+#ifndef __ALIGN_BEGIN
+#define __ALIGN_BEGIN
+#endif /* __ALIGN_BEGIN */
+#else
+#ifndef __ALIGN_END
+#define __ALIGN_END
+#endif /* __ALIGN_END */
+#ifndef __ALIGN_BEGIN
+#if defined   (__CC_ARM)      /* ARM Compiler V5*/
+#define __ALIGN_BEGIN    __align(4)
+#elif defined (__ICCARM__)    /* IAR Compiler */
+#define __ALIGN_BEGIN
+#endif /* __CC_ARM */
+#endif /* __ALIGN_BEGIN */
+#endif /* __GNUC__ */
+
+
+/**
+  * @brief  __RAM_FUNC definition
+  */
+#if defined ( __CC_ARM   ) || (defined (__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050))
+/* ARM Compiler V4/V5 and V6
+   --------------------------
+   RAM functions are defined using the toolchain options.
+   Functions that are executed in RAM should reside in a separate source module.
+   Using the 'Options for File' dialog you can simply change the 'Code / Const'
+   area of a module to a memory space in physical RAM.
+   Available memory areas are declared in the 'Target' tab of the 'Options for Target'
+   dialog.
+*/
+#define __RAM_FUNC
+
+#elif defined ( __ICCARM__ )
+/* ICCARM Compiler
+   ---------------
+   RAM functions are defined using a specific toolchain keyword "__ramfunc".
+*/
+#define __RAM_FUNC __ramfunc
+
+#elif defined   (  __GNUC__  )
+/* GNU Compiler
+   ------------
+  RAM functions are defined using a specific toolchain attribute
+   "__attribute__((section(".RamFunc")))".
+*/
+#define __RAM_FUNC __attribute__((section(".RamFunc")))
+
+#endif
+
+/**
+  * @brief  __NOINLINE definition
+  */
+#if defined ( __CC_ARM   ) || (defined (__ARMCC_VERSION) && (__ARMCC_VERSION >= 6010050)) || defined   (  __GNUC__  )
+/* ARM V4/V5 and V6 & GNU Compiler
+   -------------------------------
+*/
+#define __NOINLINE __attribute__ ( (noinline) )
+
+#elif defined ( __ICCARM__ )
+/* ICCARM Compiler
+   ---------------
+*/
+#define __NOINLINE _Pragma("optimize = no_inline")
+
+#endif
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* ___STM32F1xx_HAL_DEF */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_dma.h

@@ -0,0 +1,457 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_hal_dma.h
+  * @author  MCD Application Team
+  * @brief   Header file of DMA HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F1xx_HAL_DMA_H
+#define __STM32F1xx_HAL_DMA_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_hal_def.h"
+
+/** @addtogroup STM32F1xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup DMA
+  * @{
+  */
+
+/* Exported types ------------------------------------------------------------*/
+
+/** @defgroup DMA_Exported_Types DMA Exported Types
+  * @{
+  */
+
+/**
+  * @brief  DMA Configuration Structure definition
+  */
+typedef struct
+{
+  uint32_t Direction;                 /*!< Specifies if the data will be transferred from memory to peripheral, 
+                                           from memory to memory or from peripheral to memory.
+                                           This parameter can be a value of @ref DMA_Data_transfer_direction */
+
+  uint32_t PeriphInc;                 /*!< Specifies whether the Peripheral address register should be incremented or not.
+                                           This parameter can be a value of @ref DMA_Peripheral_incremented_mode */
+
+  uint32_t MemInc;                    /*!< Specifies whether the memory address register should be incremented or not.
+                                           This parameter can be a value of @ref DMA_Memory_incremented_mode */
+
+  uint32_t PeriphDataAlignment;       /*!< Specifies the Peripheral data width.
+                                           This parameter can be a value of @ref DMA_Peripheral_data_size */
+
+  uint32_t MemDataAlignment;          /*!< Specifies the Memory data width.
+                                           This parameter can be a value of @ref DMA_Memory_data_size */
+
+  uint32_t Mode;                      /*!< Specifies the operation mode of the DMAy Channelx.
+                                           This parameter can be a value of @ref DMA_mode
+                                           @note The circular buffer mode cannot be used if the memory-to-memory
+                                                 data transfer is configured on the selected Channel */
+
+  uint32_t Priority;                  /*!< Specifies the software priority for the DMAy Channelx.
+                                           This parameter can be a value of @ref DMA_Priority_level */
+} DMA_InitTypeDef;
+
+/**
+  * @brief  HAL DMA State structures definition
+  */
+typedef enum
+{
+  HAL_DMA_STATE_RESET             = 0x00U,  /*!< DMA not yet initialized or disabled    */
+  HAL_DMA_STATE_READY             = 0x01U,  /*!< DMA initialized and ready for use      */
+  HAL_DMA_STATE_BUSY              = 0x02U,  /*!< DMA process is ongoing                 */
+  HAL_DMA_STATE_TIMEOUT           = 0x03U   /*!< DMA timeout state                      */
+}HAL_DMA_StateTypeDef;
+
+/**
+  * @brief  HAL DMA Error Code structure definition
+  */
+typedef enum
+{
+  HAL_DMA_FULL_TRANSFER           = 0x00U,    /*!< Full transfer     */
+  HAL_DMA_HALF_TRANSFER           = 0x01U     /*!< Half Transfer     */
+}HAL_DMA_LevelCompleteTypeDef;
+
+/** 
+  * @brief  HAL DMA Callback ID structure definition
+  */
+typedef enum
+{
+  HAL_DMA_XFER_CPLT_CB_ID          = 0x00U,    /*!< Full transfer     */
+  HAL_DMA_XFER_HALFCPLT_CB_ID      = 0x01U,    /*!< Half transfer     */
+  HAL_DMA_XFER_ERROR_CB_ID         = 0x02U,    /*!< Error             */ 
+  HAL_DMA_XFER_ABORT_CB_ID         = 0x03U,    /*!< Abort             */ 
+  HAL_DMA_XFER_ALL_CB_ID           = 0x04U     /*!< All               */ 
+    
+}HAL_DMA_CallbackIDTypeDef;
+
+/** 
+  * @brief  DMA handle Structure definition
+  */
+typedef struct __DMA_HandleTypeDef
+{
+  DMA_Channel_TypeDef   *Instance;                       /*!< Register base address                  */
+  
+  DMA_InitTypeDef       Init;                            /*!< DMA communication parameters           */ 
+  
+  HAL_LockTypeDef       Lock;                            /*!< DMA locking object                     */  
+  
+  HAL_DMA_StateTypeDef  State;                           /*!< DMA transfer state                     */
+  
+  void                  *Parent;                                                      /*!< Parent object state                    */  
+  
+  void                  (* XferCpltCallback)( struct __DMA_HandleTypeDef * hdma);     /*!< DMA transfer complete callback         */
+  
+  void                  (* XferHalfCpltCallback)( struct __DMA_HandleTypeDef * hdma); /*!< DMA Half transfer complete callback    */
+  
+  void                  (* XferErrorCallback)( struct __DMA_HandleTypeDef * hdma);    /*!< DMA transfer error callback            */
+
+  void                  (* XferAbortCallback)( struct __DMA_HandleTypeDef * hdma);    /*!< DMA transfer abort callback            */  
+  
+  __IO uint32_t         ErrorCode;                                                    /*!< DMA Error code                         */
+
+  DMA_TypeDef            *DmaBaseAddress;                                             /*!< DMA Channel Base Address               */
+  
+  uint32_t               ChannelIndex;                                                /*!< DMA Channel Index                      */  
+
+} DMA_HandleTypeDef;    
+/**
+  * @}
+  */
+
+/* Exported constants --------------------------------------------------------*/
+
+/** @defgroup DMA_Exported_Constants DMA Exported Constants
+  * @{
+  */
+
+/** @defgroup DMA_Error_Code DMA Error Code
+  * @{
+  */
+#define HAL_DMA_ERROR_NONE                     0x00000000U    /*!< No error             */
+#define HAL_DMA_ERROR_TE                       0x00000001U    /*!< Transfer error       */
+#define HAL_DMA_ERROR_NO_XFER                  0x00000004U    /*!< no ongoing transfer  */
+#define HAL_DMA_ERROR_TIMEOUT                  0x00000020U    /*!< Timeout error        */
+#define HAL_DMA_ERROR_NOT_SUPPORTED            0x00000100U    /*!< Not supported mode                    */ 
+/**
+  * @}
+  */
+
+/** @defgroup DMA_Data_transfer_direction DMA Data transfer direction
+  * @{
+  */
+#define DMA_PERIPH_TO_MEMORY         0x00000000U                 /*!< Peripheral to memory direction */
+#define DMA_MEMORY_TO_PERIPH         ((uint32_t)DMA_CCR_DIR)     /*!< Memory to peripheral direction */
+#define DMA_MEMORY_TO_MEMORY         ((uint32_t)DMA_CCR_MEM2MEM) /*!< Memory to memory direction     */
+
+/**
+  * @}
+  */
+
+/** @defgroup DMA_Peripheral_incremented_mode DMA Peripheral incremented mode
+  * @{
+  */
+#define DMA_PINC_ENABLE        ((uint32_t)DMA_CCR_PINC)  /*!< Peripheral increment mode Enable */
+#define DMA_PINC_DISABLE       0x00000000U               /*!< Peripheral increment mode Disable */
+/**
+  * @}
+  */
+
+/** @defgroup DMA_Memory_incremented_mode DMA Memory incremented mode
+  * @{
+  */
+#define DMA_MINC_ENABLE         ((uint32_t)DMA_CCR_MINC)  /*!< Memory increment mode Enable  */
+#define DMA_MINC_DISABLE        0x00000000U               /*!< Memory increment mode Disable */
+/**
+  * @}
+  */
+
+/** @defgroup DMA_Peripheral_data_size DMA Peripheral data size
+  * @{
+  */
+#define DMA_PDATAALIGN_BYTE          0x00000000U                  /*!< Peripheral data alignment: Byte     */
+#define DMA_PDATAALIGN_HALFWORD      ((uint32_t)DMA_CCR_PSIZE_0)  /*!< Peripheral data alignment: HalfWord */
+#define DMA_PDATAALIGN_WORD          ((uint32_t)DMA_CCR_PSIZE_1)  /*!< Peripheral data alignment: Word     */
+/**
+  * @}
+  */
+
+/** @defgroup DMA_Memory_data_size DMA Memory data size
+  * @{
+  */
+#define DMA_MDATAALIGN_BYTE          0x00000000U                  /*!< Memory data alignment: Byte     */
+#define DMA_MDATAALIGN_HALFWORD      ((uint32_t)DMA_CCR_MSIZE_0)  /*!< Memory data alignment: HalfWord */
+#define DMA_MDATAALIGN_WORD          ((uint32_t)DMA_CCR_MSIZE_1)  /*!< Memory data alignment: Word     */
+/**
+  * @}
+  */
+
+/** @defgroup DMA_mode DMA mode
+  * @{
+  */
+#define DMA_NORMAL         0x00000000U                  /*!< Normal mode                  */
+#define DMA_CIRCULAR       ((uint32_t)DMA_CCR_CIRC)     /*!< Circular mode                */
+/**
+  * @}
+  */
+
+/** @defgroup DMA_Priority_level DMA Priority level
+  * @{
+  */
+#define DMA_PRIORITY_LOW             0x00000000U               /*!< Priority level : Low       */
+#define DMA_PRIORITY_MEDIUM          ((uint32_t)DMA_CCR_PL_0)  /*!< Priority level : Medium    */
+#define DMA_PRIORITY_HIGH            ((uint32_t)DMA_CCR_PL_1)  /*!< Priority level : High      */
+#define DMA_PRIORITY_VERY_HIGH       ((uint32_t)DMA_CCR_PL)    /*!< Priority level : Very_High */
+/**
+  * @}
+  */
+
+
+/** @defgroup DMA_interrupt_enable_definitions DMA interrupt enable definitions
+  * @{
+  */
+#define DMA_IT_TC                         ((uint32_t)DMA_CCR_TCIE)
+#define DMA_IT_HT                         ((uint32_t)DMA_CCR_HTIE)
+#define DMA_IT_TE                         ((uint32_t)DMA_CCR_TEIE)
+/**
+  * @}
+  */
+
+/** @defgroup DMA_flag_definitions DMA flag definitions
+  * @{
+  */
+#define DMA_FLAG_GL1                      0x00000001U
+#define DMA_FLAG_TC1                      0x00000002U
+#define DMA_FLAG_HT1                      0x00000004U
+#define DMA_FLAG_TE1                      0x00000008U
+#define DMA_FLAG_GL2                      0x00000010U
+#define DMA_FLAG_TC2                      0x00000020U
+#define DMA_FLAG_HT2                      0x00000040U
+#define DMA_FLAG_TE2                      0x00000080U
+#define DMA_FLAG_GL3                      0x00000100U
+#define DMA_FLAG_TC3                      0x00000200U
+#define DMA_FLAG_HT3                      0x00000400U
+#define DMA_FLAG_TE3                      0x00000800U
+#define DMA_FLAG_GL4                      0x00001000U
+#define DMA_FLAG_TC4                      0x00002000U
+#define DMA_FLAG_HT4                      0x00004000U
+#define DMA_FLAG_TE4                      0x00008000U
+#define DMA_FLAG_GL5                      0x00010000U
+#define DMA_FLAG_TC5                      0x00020000U
+#define DMA_FLAG_HT5                      0x00040000U
+#define DMA_FLAG_TE5                      0x00080000U
+#define DMA_FLAG_GL6                      0x00100000U
+#define DMA_FLAG_TC6                      0x00200000U
+#define DMA_FLAG_HT6                      0x00400000U
+#define DMA_FLAG_TE6                      0x00800000U
+#define DMA_FLAG_GL7                      0x01000000U
+#define DMA_FLAG_TC7                      0x02000000U
+#define DMA_FLAG_HT7                      0x04000000U
+#define DMA_FLAG_TE7                      0x08000000U
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+
+/* Exported macros -----------------------------------------------------------*/
+/** @defgroup DMA_Exported_Macros DMA Exported Macros
+  * @{
+  */
+
+/** @brief  Reset DMA handle state.
+  * @param  __HANDLE__: DMA handle
+  * @retval None
+  */
+#define __HAL_DMA_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_DMA_STATE_RESET)
+
+/**
+  * @brief  Enable the specified DMA Channel.
+  * @param  __HANDLE__: DMA handle
+  * @retval None
+  */
+#define __HAL_DMA_ENABLE(__HANDLE__)        (SET_BIT((__HANDLE__)->Instance->CCR, DMA_CCR_EN))
+
+/**
+  * @brief  Disable the specified DMA Channel.
+  * @param  __HANDLE__: DMA handle
+  * @retval None
+  */
+#define __HAL_DMA_DISABLE(__HANDLE__)       (CLEAR_BIT((__HANDLE__)->Instance->CCR, DMA_CCR_EN))
+
+
+/* Interrupt & Flag management */
+
+/**
+  * @brief  Enables the specified DMA Channel interrupts.
+  * @param  __HANDLE__: DMA handle
+  * @param __INTERRUPT__: specifies the DMA interrupt sources to be enabled or disabled.
+  *          This parameter can be any combination of the following values:
+  *            @arg DMA_IT_TC:  Transfer complete interrupt mask
+  *            @arg DMA_IT_HT:  Half transfer complete interrupt mask
+  *            @arg DMA_IT_TE:  Transfer error interrupt mask
+  * @retval None
+  */
+#define __HAL_DMA_ENABLE_IT(__HANDLE__, __INTERRUPT__)   (SET_BIT((__HANDLE__)->Instance->CCR, (__INTERRUPT__)))
+
+/**
+  * @brief  Disable the specified DMA Channel interrupts.
+  * @param  __HANDLE__: DMA handle
+  * @param  __INTERRUPT__: specifies the DMA interrupt sources to be enabled or disabled.
+  *          This parameter can be any combination of the following values:
+  *            @arg DMA_IT_TC:  Transfer complete interrupt mask
+  *            @arg DMA_IT_HT:  Half transfer complete interrupt mask
+  *            @arg DMA_IT_TE:  Transfer error interrupt mask
+  * @retval None
+  */
+#define __HAL_DMA_DISABLE_IT(__HANDLE__, __INTERRUPT__)  (CLEAR_BIT((__HANDLE__)->Instance->CCR , (__INTERRUPT__)))
+
+/**
+  * @brief  Check whether the specified DMA Channel interrupt is enabled or not.
+  * @param  __HANDLE__: DMA handle
+  * @param  __INTERRUPT__: specifies the DMA interrupt source to check.
+  *          This parameter can be one of the following values:
+  *            @arg DMA_IT_TC:  Transfer complete interrupt mask
+  *            @arg DMA_IT_HT:  Half transfer complete interrupt mask
+  *            @arg DMA_IT_TE:  Transfer error interrupt mask
+  * @retval The state of DMA_IT (SET or RESET).
+  */
+#define __HAL_DMA_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__)  ((((__HANDLE__)->Instance->CCR & (__INTERRUPT__)) == (__INTERRUPT__)) ? SET : RESET)
+
+/**
+  * @brief  Return the number of remaining data units in the current DMA Channel transfer.
+  * @param  __HANDLE__: DMA handle
+  * @retval The number of remaining data units in the current DMA Channel transfer.
+  */
+#define __HAL_DMA_GET_COUNTER(__HANDLE__) ((__HANDLE__)->Instance->CNDTR)
+
+/**
+  * @}
+  */
+
+/* Include DMA HAL Extension module */
+#include "stm32f1xx_hal_dma_ex.h"   
+
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup DMA_Exported_Functions
+  * @{
+  */
+
+/** @addtogroup DMA_Exported_Functions_Group1
+  * @{
+  */
+/* Initialization and de-initialization functions *****************************/
+HAL_StatusTypeDef HAL_DMA_Init(DMA_HandleTypeDef *hdma);
+HAL_StatusTypeDef HAL_DMA_DeInit (DMA_HandleTypeDef *hdma);
+/**
+  * @}
+  */
+
+/** @addtogroup DMA_Exported_Functions_Group2
+  * @{
+  */
+/* IO operation functions *****************************************************/
+HAL_StatusTypeDef HAL_DMA_Start (DMA_HandleTypeDef *hdma, uint32_t SrcAddress, uint32_t DstAddress, uint32_t DataLength);
+HAL_StatusTypeDef HAL_DMA_Start_IT(DMA_HandleTypeDef *hdma, uint32_t SrcAddress, uint32_t DstAddress, uint32_t DataLength);
+HAL_StatusTypeDef HAL_DMA_Abort(DMA_HandleTypeDef *hdma);
+HAL_StatusTypeDef HAL_DMA_Abort_IT(DMA_HandleTypeDef *hdma);
+HAL_StatusTypeDef HAL_DMA_PollForTransfer(DMA_HandleTypeDef *hdma, uint32_t CompleteLevel, uint32_t Timeout);
+void HAL_DMA_IRQHandler(DMA_HandleTypeDef *hdma);
+HAL_StatusTypeDef HAL_DMA_RegisterCallback(DMA_HandleTypeDef *hdma, HAL_DMA_CallbackIDTypeDef CallbackID, void (* pCallback)( DMA_HandleTypeDef * _hdma));
+HAL_StatusTypeDef HAL_DMA_UnRegisterCallback(DMA_HandleTypeDef *hdma, HAL_DMA_CallbackIDTypeDef CallbackID);
+
+/**
+  * @}
+  */
+
+/** @addtogroup DMA_Exported_Functions_Group3
+  * @{
+  */
+/* Peripheral State and Error functions ***************************************/
+HAL_DMA_StateTypeDef HAL_DMA_GetState(DMA_HandleTypeDef *hdma);
+uint32_t HAL_DMA_GetError(DMA_HandleTypeDef *hdma);
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Private macros ------------------------------------------------------------*/
+/** @defgroup DMA_Private_Macros DMA Private Macros
+  * @{
+  */
+
+#define IS_DMA_DIRECTION(DIRECTION) (((DIRECTION) == DMA_PERIPH_TO_MEMORY ) || \
+                                     ((DIRECTION) == DMA_MEMORY_TO_PERIPH)  || \
+                                     ((DIRECTION) == DMA_MEMORY_TO_MEMORY))
+
+#define IS_DMA_BUFFER_SIZE(SIZE) (((SIZE) >= 0x1U) && ((SIZE) < 0x10000U))
+
+#define IS_DMA_PERIPHERAL_INC_STATE(STATE) (((STATE) == DMA_PINC_ENABLE) || \
+                                            ((STATE) == DMA_PINC_DISABLE))
+
+#define IS_DMA_MEMORY_INC_STATE(STATE) (((STATE) == DMA_MINC_ENABLE)  || \
+                                        ((STATE) == DMA_MINC_DISABLE))
+
+#define IS_DMA_PERIPHERAL_DATA_SIZE(SIZE) (((SIZE) == DMA_PDATAALIGN_BYTE)     || \
+                                           ((SIZE) == DMA_PDATAALIGN_HALFWORD) || \
+                                           ((SIZE) == DMA_PDATAALIGN_WORD))
+
+#define IS_DMA_MEMORY_DATA_SIZE(SIZE) (((SIZE) == DMA_MDATAALIGN_BYTE)     || \
+                                       ((SIZE) == DMA_MDATAALIGN_HALFWORD) || \
+                                       ((SIZE) == DMA_MDATAALIGN_WORD ))
+
+#define IS_DMA_MODE(MODE) (((MODE) == DMA_NORMAL )  || \
+                           ((MODE) == DMA_CIRCULAR))
+
+#define IS_DMA_PRIORITY(PRIORITY) (((PRIORITY) == DMA_PRIORITY_LOW )   || \
+                                   ((PRIORITY) == DMA_PRIORITY_MEDIUM) || \
+                                   ((PRIORITY) == DMA_PRIORITY_HIGH)   || \
+                                   ((PRIORITY) == DMA_PRIORITY_VERY_HIGH))
+
+/**
+  * @}
+  */ 
+
+/* Private functions ---------------------------------------------------------*/
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F1xx_HAL_DMA_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_dma_ex.h

@@ -0,0 +1,277 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_hal_dma_ex.h
+  * @author  MCD Application Team
+  * @brief   Header file of DMA HAL extension module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F1xx_HAL_DMA_EX_H
+#define __STM32F1xx_HAL_DMA_EX_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_hal_def.h"
+
+/** @addtogroup STM32F1xx_HAL_Driver
+  * @{
+  */
+
+/** @defgroup DMAEx DMAEx
+  * @{
+  */
+
+/* Exported types ------------------------------------------------------------*/ 
+/* Exported constants --------------------------------------------------------*/
+/* Exported macro ------------------------------------------------------------*/
+/** @defgroup DMAEx_Exported_Macros DMA Extended Exported Macros
+  * @{
+  */
+/* Interrupt & Flag management */
+#if defined (STM32F100xE) || defined (STM32F101xE) || defined (STM32F101xG) || defined (STM32F103xE) || \
+    defined (STM32F103xG) || defined (STM32F105xC) || defined (STM32F107xC)
+/** @defgroup DMAEx_High_density_XL_density_Product_devices DMAEx High density and XL density product devices
+  * @{
+  */
+
+/**
+  * @brief  Returns the current DMA Channel transfer complete flag.
+  * @param  __HANDLE__: DMA handle
+  * @retval The specified transfer complete flag index.
+  */
+#define __HAL_DMA_GET_TC_FLAG_INDEX(__HANDLE__) \
+(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel1))? DMA_FLAG_TC1 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel2))? DMA_FLAG_TC2 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel3))? DMA_FLAG_TC3 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel4))? DMA_FLAG_TC4 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel5))? DMA_FLAG_TC5 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel6))? DMA_FLAG_TC6 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel7))? DMA_FLAG_TC7 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel1))? DMA_FLAG_TC1 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel2))? DMA_FLAG_TC2 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel3))? DMA_FLAG_TC3 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel4))? DMA_FLAG_TC4 :\
+   DMA_FLAG_TC5)
+
+/**
+  * @brief  Returns the current DMA Channel half transfer complete flag.
+  * @param  __HANDLE__: DMA handle
+  * @retval The specified half transfer complete flag index.
+  */      
+#define __HAL_DMA_GET_HT_FLAG_INDEX(__HANDLE__)\
+(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel1))? DMA_FLAG_HT1 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel2))? DMA_FLAG_HT2 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel3))? DMA_FLAG_HT3 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel4))? DMA_FLAG_HT4 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel5))? DMA_FLAG_HT5 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel6))? DMA_FLAG_HT6 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel7))? DMA_FLAG_HT7 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel1))? DMA_FLAG_HT1 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel2))? DMA_FLAG_HT2 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel3))? DMA_FLAG_HT3 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel4))? DMA_FLAG_HT4 :\
+   DMA_FLAG_HT5)
+
+/**
+  * @brief  Returns the current DMA Channel transfer error flag.
+  * @param  __HANDLE__: DMA handle
+  * @retval The specified transfer error flag index.
+  */
+#define __HAL_DMA_GET_TE_FLAG_INDEX(__HANDLE__)\
+(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel1))? DMA_FLAG_TE1 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel2))? DMA_FLAG_TE2 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel3))? DMA_FLAG_TE3 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel4))? DMA_FLAG_TE4 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel5))? DMA_FLAG_TE5 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel6))? DMA_FLAG_TE6 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel7))? DMA_FLAG_TE7 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel1))? DMA_FLAG_TE1 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel2))? DMA_FLAG_TE2 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel3))? DMA_FLAG_TE3 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel4))? DMA_FLAG_TE4 :\
+   DMA_FLAG_TE5)
+
+/**
+  * @brief  Return the current DMA Channel Global interrupt flag.
+  * @param  __HANDLE__: DMA handle
+  * @retval The specified transfer error flag index.
+  */
+#define __HAL_DMA_GET_GI_FLAG_INDEX(__HANDLE__)\
+(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel1))? DMA_FLAG_GL1 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel2))? DMA_FLAG_GL2 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel3))? DMA_FLAG_GL3 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel4))? DMA_FLAG_GL4 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel5))? DMA_FLAG_GL5 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel6))? DMA_FLAG_GL6 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel7))? DMA_FLAG_GL7 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel1))? DMA_FLAG_GL1 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel2))? DMA_FLAG_GL2 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel3))? DMA_FLAG_GL3 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA2_Channel4))? DMA_FLAG_GL4 :\
+   DMA_FLAG_GL5)
+   
+/**
+  * @brief  Get the DMA Channel pending flags.
+  * @param  __HANDLE__: DMA handle
+  * @param  __FLAG__: Get the specified flag.
+  *          This parameter can be any combination of the following values:
+  *            @arg DMA_FLAG_TCx:  Transfer complete flag
+  *            @arg DMA_FLAG_HTx:  Half transfer complete flag
+  *            @arg DMA_FLAG_TEx:  Transfer error flag
+  *         Where x can be 1_7 or 1_5 (depending on DMA1 or DMA2) to select the DMA Channel flag.   
+  * @retval The state of FLAG (SET or RESET).
+  */
+#define __HAL_DMA_GET_FLAG(__HANDLE__, __FLAG__)\
+(((uint32_t)((__HANDLE__)->Instance) > (uint32_t)DMA1_Channel7)? (DMA2->ISR & (__FLAG__)) :\
+  (DMA1->ISR & (__FLAG__)))
+
+/**
+  * @brief  Clears the DMA Channel pending flags.
+  * @param  __HANDLE__: DMA handle
+  * @param  __FLAG__: specifies the flag to clear.
+  *          This parameter can be any combination of the following values:
+  *            @arg DMA_FLAG_TCx:  Transfer complete flag
+  *            @arg DMA_FLAG_HTx:  Half transfer complete flag
+  *            @arg DMA_FLAG_TEx:  Transfer error flag
+  *         Where x can be 1_7 or 1_5 (depending on DMA1 or DMA2) to select the DMA Channel flag.   
+  * @retval None
+  */
+#define __HAL_DMA_CLEAR_FLAG(__HANDLE__, __FLAG__) \
+(((uint32_t)((__HANDLE__)->Instance) > (uint32_t)DMA1_Channel7)? (DMA2->IFCR = (__FLAG__)) :\
+  (DMA1->IFCR = (__FLAG__)))
+
+/**
+  * @}
+  */
+
+#else
+/** @defgroup DMA_Low_density_Medium_density_Product_devices DMA Low density and Medium density product devices
+  * @{
+  */
+
+/**
+  * @brief  Returns the current DMA Channel transfer complete flag.
+  * @param  __HANDLE__: DMA handle
+  * @retval The specified transfer complete flag index.
+  */
+#define __HAL_DMA_GET_TC_FLAG_INDEX(__HANDLE__) \
+(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel1))? DMA_FLAG_TC1 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel2))? DMA_FLAG_TC2 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel3))? DMA_FLAG_TC3 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel4))? DMA_FLAG_TC4 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel5))? DMA_FLAG_TC5 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel6))? DMA_FLAG_TC6 :\
+   DMA_FLAG_TC7)
+
+/**
+  * @brief  Return the current DMA Channel half transfer complete flag.
+  * @param  __HANDLE__: DMA handle
+  * @retval The specified half transfer complete flag index.
+  */
+#define __HAL_DMA_GET_HT_FLAG_INDEX(__HANDLE__)\
+(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel1))? DMA_FLAG_HT1 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel2))? DMA_FLAG_HT2 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel3))? DMA_FLAG_HT3 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel4))? DMA_FLAG_HT4 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel5))? DMA_FLAG_HT5 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel6))? DMA_FLAG_HT6 :\
+   DMA_FLAG_HT7)
+
+/**
+  * @brief  Return the current DMA Channel transfer error flag.
+  * @param  __HANDLE__: DMA handle
+  * @retval The specified transfer error flag index.
+  */
+#define __HAL_DMA_GET_TE_FLAG_INDEX(__HANDLE__)\
+(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel1))? DMA_FLAG_TE1 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel2))? DMA_FLAG_TE2 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel3))? DMA_FLAG_TE3 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel4))? DMA_FLAG_TE4 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel5))? DMA_FLAG_TE5 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel6))? DMA_FLAG_TE6 :\
+   DMA_FLAG_TE7)
+
+/**
+  * @brief  Return the current DMA Channel Global interrupt flag.
+  * @param  __HANDLE__: DMA handle
+  * @retval The specified transfer error flag index.
+  */
+#define __HAL_DMA_GET_GI_FLAG_INDEX(__HANDLE__)\
+(((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel1))? DMA_FLAG_GL1 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel2))? DMA_FLAG_GL2 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel3))? DMA_FLAG_GL3 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel4))? DMA_FLAG_GL4 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel5))? DMA_FLAG_GL5 :\
+ ((uint32_t)((__HANDLE__)->Instance) == ((uint32_t)DMA1_Channel6))? DMA_FLAG_GL6 :\
+   DMA_FLAG_GL7)
+
+/**
+  * @brief  Get the DMA Channel pending flags.
+  * @param  __HANDLE__: DMA handle
+  * @param  __FLAG__: Get the specified flag.
+  *          This parameter can be any combination of the following values:
+  *            @arg DMA_FLAG_TCx:  Transfer complete flag
+  *            @arg DMA_FLAG_HTx:  Half transfer complete flag
+  *            @arg DMA_FLAG_TEx:  Transfer error flag
+  *            @arg DMA_FLAG_GLx:  Global interrupt flag
+  *         Where x can be 1_7 to select the DMA Channel flag.   
+  * @retval The state of FLAG (SET or RESET).
+  */
+
+#define __HAL_DMA_GET_FLAG(__HANDLE__, __FLAG__)   (DMA1->ISR & (__FLAG__))
+
+/**
+  * @brief  Clear the DMA Channel pending flags.
+  * @param  __HANDLE__: DMA handle
+  * @param  __FLAG__: specifies the flag to clear.
+  *          This parameter can be any combination of the following values:
+  *            @arg DMA_FLAG_TCx:  Transfer complete flag
+  *            @arg DMA_FLAG_HTx:  Half transfer complete flag
+  *            @arg DMA_FLAG_TEx:  Transfer error flag
+  *            @arg DMA_FLAG_GLx:  Global interrupt flag
+  *         Where x can be 1_7 to select the DMA Channel flag.   
+  * @retval None
+  */
+#define __HAL_DMA_CLEAR_FLAG(__HANDLE__, __FLAG__) (DMA1->IFCR = (__FLAG__))
+
+/**
+  * @}
+  */
+
+#endif
+  
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif /* STM32F100xE || STM32F101xE || STM32F101xG || STM32F103xE || */
+       /* STM32F103xG || STM32F105xC || STM32F107xC */
+
+#endif /* __STM32F1xx_HAL_DMA_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_exti.h

@@ -0,0 +1,320 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_hal_exti.h
+  * @author  MCD Application Team
+  * @brief   Header file of EXTI HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2019 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef STM32F1xx_HAL_EXTI_H
+#define STM32F1xx_HAL_EXTI_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_hal_def.h"
+
+/** @addtogroup STM32F1xx_HAL_Driver
+  * @{
+  */
+
+/** @defgroup EXTI EXTI
+  * @brief EXTI HAL module driver
+  * @{
+  */
+
+/* Exported types ------------------------------------------------------------*/
+
+/** @defgroup EXTI_Exported_Types EXTI Exported Types
+  * @{
+  */
+
+/**
+  * @brief  HAL EXTI common Callback ID enumeration definition
+  */
+typedef enum
+{
+  HAL_EXTI_COMMON_CB_ID          = 0x00U
+} EXTI_CallbackIDTypeDef;
+
+/**
+  * @brief  EXTI Handle structure definition
+  */
+typedef struct
+{
+  uint32_t Line;                    /*!<  Exti line number */
+  void (* PendingCallback)(void);   /*!<  Exti pending callback */
+} EXTI_HandleTypeDef;
+
+/**
+  * @brief  EXTI Configuration structure definition
+  */
+typedef struct
+{
+  uint32_t Line;      /*!< The Exti line to be configured. This parameter
+                           can be a value of @ref EXTI_Line */
+  uint32_t Mode;      /*!< The Exit Mode to be configured for a core.
+                           This parameter can be a combination of @ref EXTI_Mode */
+  uint32_t Trigger;   /*!< The Exti Trigger to be configured. This parameter
+                           can be a value of @ref EXTI_Trigger */
+  uint32_t GPIOSel;   /*!< The Exti GPIO multiplexer selection to be configured.
+                           This parameter is only possible for line 0 to 15. It
+                           can be a value of @ref EXTI_GPIOSel */
+} EXTI_ConfigTypeDef;
+
+/**
+  * @}
+  */
+
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup EXTI_Exported_Constants EXTI Exported Constants
+  * @{
+  */
+
+/** @defgroup EXTI_Line  EXTI Line
+  * @{
+  */
+#define EXTI_LINE_0                        (EXTI_GPIO     | 0x00u)    /*!< External interrupt line 0 */
+#define EXTI_LINE_1                        (EXTI_GPIO     | 0x01u)    /*!< External interrupt line 1 */
+#define EXTI_LINE_2                        (EXTI_GPIO     | 0x02u)    /*!< External interrupt line 2 */
+#define EXTI_LINE_3                        (EXTI_GPIO     | 0x03u)    /*!< External interrupt line 3 */
+#define EXTI_LINE_4                        (EXTI_GPIO     | 0x04u)    /*!< External interrupt line 4 */
+#define EXTI_LINE_5                        (EXTI_GPIO     | 0x05u)    /*!< External interrupt line 5 */
+#define EXTI_LINE_6                        (EXTI_GPIO     | 0x06u)    /*!< External interrupt line 6 */
+#define EXTI_LINE_7                        (EXTI_GPIO     | 0x07u)    /*!< External interrupt line 7 */
+#define EXTI_LINE_8                        (EXTI_GPIO     | 0x08u)    /*!< External interrupt line 8 */
+#define EXTI_LINE_9                        (EXTI_GPIO     | 0x09u)    /*!< External interrupt line 9 */
+#define EXTI_LINE_10                       (EXTI_GPIO     | 0x0Au)    /*!< External interrupt line 10 */
+#define EXTI_LINE_11                       (EXTI_GPIO     | 0x0Bu)    /*!< External interrupt line 11 */
+#define EXTI_LINE_12                       (EXTI_GPIO     | 0x0Cu)    /*!< External interrupt line 12 */
+#define EXTI_LINE_13                       (EXTI_GPIO     | 0x0Du)    /*!< External interrupt line 13 */
+#define EXTI_LINE_14                       (EXTI_GPIO     | 0x0Eu)    /*!< External interrupt line 14 */
+#define EXTI_LINE_15                       (EXTI_GPIO     | 0x0Fu)    /*!< External interrupt line 15 */
+#define EXTI_LINE_16                       (EXTI_CONFIG   | 0x10u)    /*!< External interrupt line 16 Connected to the PVD Output */
+#define EXTI_LINE_17                       (EXTI_CONFIG   | 0x11u)    /*!< External interrupt line 17 Connected to the RTC Alarm event */
+#if defined(EXTI_IMR_IM18)
+#define EXTI_LINE_18                       (EXTI_CONFIG   | 0x12u)    /*!< External interrupt line 18 Connected to the USB Wakeup from suspend event */
+#endif /* EXTI_IMR_IM18 */
+#if defined(EXTI_IMR_IM19)
+#define EXTI_LINE_19                       (EXTI_CONFIG   | 0x13u)    /*!< External interrupt line 19 Connected to the Ethernet Wakeup event */
+#endif /* EXTI_IMR_IM19 */
+
+/**
+  * @}
+  */
+
+/** @defgroup EXTI_Mode  EXTI Mode
+  * @{
+  */
+#define EXTI_MODE_NONE                      0x00000000u
+#define EXTI_MODE_INTERRUPT                 0x00000001u
+#define EXTI_MODE_EVENT                     0x00000002u
+/**
+  * @}
+  */
+
+/** @defgroup EXTI_Trigger  EXTI Trigger
+  * @{
+  */
+#define EXTI_TRIGGER_NONE                   0x00000000u
+#define EXTI_TRIGGER_RISING                 0x00000001u
+#define EXTI_TRIGGER_FALLING                0x00000002u
+#define EXTI_TRIGGER_RISING_FALLING         (EXTI_TRIGGER_RISING | EXTI_TRIGGER_FALLING)
+/**
+  * @}
+  */
+
+/** @defgroup EXTI_GPIOSel  EXTI GPIOSel
+  * @brief
+  * @{
+  */
+#define EXTI_GPIOA                          0x00000000u
+#define EXTI_GPIOB                          0x00000001u
+#define EXTI_GPIOC                          0x00000002u
+#define EXTI_GPIOD                          0x00000003u
+#if defined (GPIOE)
+#define EXTI_GPIOE                          0x00000004u
+#endif /* GPIOE */
+#if defined (GPIOF)
+#define EXTI_GPIOF                          0x00000005u
+#endif /* GPIOF */
+#if defined (GPIOG)
+#define EXTI_GPIOG                          0x00000006u
+#endif /* GPIOG */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Exported macro ------------------------------------------------------------*/
+/** @defgroup EXTI_Exported_Macros EXTI Exported Macros
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/* Private constants --------------------------------------------------------*/
+/** @defgroup EXTI_Private_Constants EXTI Private Constants
+  * @{
+  */
+/**
+  * @brief  EXTI Line property definition
+  */
+#define EXTI_PROPERTY_SHIFT                 24u
+#define EXTI_CONFIG                         (0x02uL << EXTI_PROPERTY_SHIFT)
+#define EXTI_GPIO                           ((0x04uL << EXTI_PROPERTY_SHIFT) | EXTI_CONFIG)
+#define EXTI_PROPERTY_MASK                  (EXTI_CONFIG | EXTI_GPIO)
+
+/**
+  * @brief  EXTI bit usage
+  */
+#define EXTI_PIN_MASK                       0x0000001Fu
+
+/**
+  * @brief  EXTI Mask for interrupt & event mode
+  */
+#define EXTI_MODE_MASK                      (EXTI_MODE_EVENT | EXTI_MODE_INTERRUPT)
+
+/**
+  * @brief  EXTI Mask for trigger possibilities
+  */
+#define EXTI_TRIGGER_MASK                   (EXTI_TRIGGER_RISING | EXTI_TRIGGER_FALLING)
+
+/**
+  * @brief  EXTI Line number
+  */
+#if defined(EXTI_IMR_IM19)
+#define EXTI_LINE_NB                        20UL
+#elif defined(EXTI_IMR_IM18)
+#define EXTI_LINE_NB                        19UL
+#else /* EXTI_IMR_IM17 */
+#define EXTI_LINE_NB                        18UL
+#endif /* EXTI_IMR_IM19 */
+/**
+  * @}
+  */
+
+/* Private macros ------------------------------------------------------------*/
+/** @defgroup EXTI_Private_Macros EXTI Private Macros
+  * @{
+  */
+#define IS_EXTI_LINE(__EXTI_LINE__)          ((((__EXTI_LINE__) & ~(EXTI_PROPERTY_MASK | EXTI_PIN_MASK)) == 0x00u) && \
+                                             ((((__EXTI_LINE__) & EXTI_PROPERTY_MASK) == EXTI_CONFIG)   || \
+                                              (((__EXTI_LINE__) & EXTI_PROPERTY_MASK) == EXTI_GPIO))    && \
+                                              (((__EXTI_LINE__) & EXTI_PIN_MASK) < EXTI_LINE_NB))
+
+#define IS_EXTI_MODE(__EXTI_LINE__)          ((((__EXTI_LINE__) & EXTI_MODE_MASK) != 0x00u) && \
+                                              (((__EXTI_LINE__) & ~EXTI_MODE_MASK) == 0x00u))
+
+#define IS_EXTI_TRIGGER(__EXTI_LINE__)       (((__EXTI_LINE__) & ~EXTI_TRIGGER_MASK) == 0x00u)
+
+#define IS_EXTI_PENDING_EDGE(__EXTI_LINE__)  ((__EXTI_LINE__) == EXTI_TRIGGER_RISING_FALLING)
+
+#define IS_EXTI_CONFIG_LINE(__EXTI_LINE__)   (((__EXTI_LINE__) & EXTI_CONFIG) != 0x00u)
+
+#if defined (GPIOG)
+#define IS_EXTI_GPIO_PORT(__PORT__)     (((__PORT__) == EXTI_GPIOA) || \
+                                         ((__PORT__) == EXTI_GPIOB) || \
+                                         ((__PORT__) == EXTI_GPIOC) || \
+                                         ((__PORT__) == EXTI_GPIOD) || \
+                                         ((__PORT__) == EXTI_GPIOE) || \
+                                         ((__PORT__) == EXTI_GPIOF) || \
+                                         ((__PORT__) == EXTI_GPIOG))
+#elif defined (GPIOF)
+#define IS_EXTI_GPIO_PORT(__PORT__)     (((__PORT__) == EXTI_GPIOA) || \
+                                         ((__PORT__) == EXTI_GPIOB) || \
+                                         ((__PORT__) == EXTI_GPIOC) || \
+                                         ((__PORT__) == EXTI_GPIOD) || \
+                                         ((__PORT__) == EXTI_GPIOE) || \
+                                         ((__PORT__) == EXTI_GPIOF))
+#elif defined (GPIOE)
+#define IS_EXTI_GPIO_PORT(__PORT__)     (((__PORT__) == EXTI_GPIOA) || \
+                                         ((__PORT__) == EXTI_GPIOB) || \
+                                         ((__PORT__) == EXTI_GPIOC) || \
+                                         ((__PORT__) == EXTI_GPIOD) || \
+                                         ((__PORT__) == EXTI_GPIOE))
+#else
+#define IS_EXTI_GPIO_PORT(__PORT__)     (((__PORT__) == EXTI_GPIOA) || \
+                                         ((__PORT__) == EXTI_GPIOB) || \
+                                         ((__PORT__) == EXTI_GPIOC) || \
+                                         ((__PORT__) == EXTI_GPIOD))
+#endif /* GPIOG */
+
+#define IS_EXTI_GPIO_PIN(__PIN__)       ((__PIN__) < 16u)
+
+/**
+  * @}
+  */
+
+/* Exported functions --------------------------------------------------------*/
+/** @defgroup EXTI_Exported_Functions EXTI Exported Functions
+  * @brief    EXTI Exported Functions
+  * @{
+  */
+
+/** @defgroup EXTI_Exported_Functions_Group1 Configuration functions
+  * @brief    Configuration functions
+  * @{
+  */
+/* Configuration functions ****************************************************/
+HAL_StatusTypeDef HAL_EXTI_SetConfigLine(EXTI_HandleTypeDef *hexti, EXTI_ConfigTypeDef *pExtiConfig);
+HAL_StatusTypeDef HAL_EXTI_GetConfigLine(EXTI_HandleTypeDef *hexti, EXTI_ConfigTypeDef *pExtiConfig);
+HAL_StatusTypeDef HAL_EXTI_ClearConfigLine(EXTI_HandleTypeDef *hexti);
+HAL_StatusTypeDef HAL_EXTI_RegisterCallback(EXTI_HandleTypeDef *hexti, EXTI_CallbackIDTypeDef CallbackID, void (*pPendingCbfn)(void));
+HAL_StatusTypeDef HAL_EXTI_GetHandle(EXTI_HandleTypeDef *hexti, uint32_t ExtiLine);
+/**
+  * @}
+  */
+
+/** @defgroup EXTI_Exported_Functions_Group2 IO operation functions
+  * @brief    IO operation functions
+  * @{
+  */
+/* IO operation functions *****************************************************/
+void              HAL_EXTI_IRQHandler(EXTI_HandleTypeDef *hexti);
+uint32_t          HAL_EXTI_GetPending(EXTI_HandleTypeDef *hexti, uint32_t Edge);
+void              HAL_EXTI_ClearPending(EXTI_HandleTypeDef *hexti, uint32_t Edge);
+void              HAL_EXTI_GenerateSWI(EXTI_HandleTypeDef *hexti);
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* STM32F1xx_HAL_EXTI_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_flash.h

@@ -0,0 +1,328 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_hal_flash.h
+  * @author  MCD Application Team
+  * @brief   Header file of Flash HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F1xx_HAL_FLASH_H
+#define __STM32F1xx_HAL_FLASH_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_hal_def.h"
+   
+/** @addtogroup STM32F1xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup FLASH
+  * @{
+  */
+  
+/** @addtogroup FLASH_Private_Constants
+  * @{
+  */
+#define FLASH_TIMEOUT_VALUE              50000U /* 50 s */
+/**
+  * @}
+  */
+
+/** @addtogroup FLASH_Private_Macros
+  * @{
+  */
+
+#define IS_FLASH_TYPEPROGRAM(VALUE)  (((VALUE) == FLASH_TYPEPROGRAM_HALFWORD) || \
+                                      ((VALUE) == FLASH_TYPEPROGRAM_WORD)     || \
+                                      ((VALUE) == FLASH_TYPEPROGRAM_DOUBLEWORD))  
+
+#if   defined(FLASH_ACR_LATENCY)
+#define IS_FLASH_LATENCY(__LATENCY__) (((__LATENCY__) == FLASH_LATENCY_0) || \
+                                       ((__LATENCY__) == FLASH_LATENCY_1) || \
+                                       ((__LATENCY__) == FLASH_LATENCY_2))
+
+#else
+#define IS_FLASH_LATENCY(__LATENCY__)   ((__LATENCY__) == FLASH_LATENCY_0)
+#endif /* FLASH_ACR_LATENCY */
+/**
+  * @}
+  */  
+
+/* Exported types ------------------------------------------------------------*/ 
+/** @defgroup FLASH_Exported_Types FLASH Exported Types
+  * @{
+  */  
+
+/**
+  * @brief  FLASH Procedure structure definition
+  */
+typedef enum 
+{
+  FLASH_PROC_NONE              = 0U, 
+  FLASH_PROC_PAGEERASE         = 1U,
+  FLASH_PROC_MASSERASE         = 2U,
+  FLASH_PROC_PROGRAMHALFWORD   = 3U,
+  FLASH_PROC_PROGRAMWORD       = 4U,
+  FLASH_PROC_PROGRAMDOUBLEWORD = 5U
+} FLASH_ProcedureTypeDef;
+
+/** 
+  * @brief  FLASH handle Structure definition  
+  */
+typedef struct
+{
+  __IO FLASH_ProcedureTypeDef ProcedureOnGoing; /*!< Internal variable to indicate which procedure is ongoing or not in IT context */
+  
+  __IO uint32_t               DataRemaining;    /*!< Internal variable to save the remaining pages to erase or half-word to program in IT context */
+
+  __IO uint32_t               Address;          /*!< Internal variable to save address selected for program or erase */
+
+  __IO uint64_t               Data;             /*!< Internal variable to save data to be programmed */
+
+  HAL_LockTypeDef             Lock;             /*!< FLASH locking object                */
+
+  __IO uint32_t               ErrorCode;        /*!< FLASH error code                    
+                                                     This parameter can be a value of @ref FLASH_Error_Codes  */
+} FLASH_ProcessTypeDef;
+
+/**
+  * @}
+  */
+
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup FLASH_Exported_Constants FLASH Exported Constants
+  * @{
+  */  
+
+/** @defgroup FLASH_Error_Codes FLASH Error Codes
+  * @{
+  */
+
+#define HAL_FLASH_ERROR_NONE      0x00U  /*!< No error */
+#define HAL_FLASH_ERROR_PROG      0x01U  /*!< Programming error */
+#define HAL_FLASH_ERROR_WRP       0x02U  /*!< Write protection error */
+#define HAL_FLASH_ERROR_OPTV      0x04U  /*!< Option validity error */
+
+/**
+  * @}
+  */
+
+/** @defgroup FLASH_Type_Program FLASH Type Program
+  * @{
+  */ 
+#define FLASH_TYPEPROGRAM_HALFWORD             0x01U  /*!<Program a half-word (16-bit) at a specified address.*/
+#define FLASH_TYPEPROGRAM_WORD                 0x02U  /*!<Program a word (32-bit) at a specified address.*/
+#define FLASH_TYPEPROGRAM_DOUBLEWORD           0x03U  /*!<Program a double word (64-bit) at a specified address*/
+
+/**
+  * @}
+  */
+
+#if   defined(FLASH_ACR_LATENCY)
+/** @defgroup FLASH_Latency FLASH Latency
+  * @{
+  */
+#define FLASH_LATENCY_0            0x00000000U               /*!< FLASH Zero Latency cycle */
+#define FLASH_LATENCY_1            FLASH_ACR_LATENCY_0       /*!< FLASH One Latency cycle */
+#define FLASH_LATENCY_2            FLASH_ACR_LATENCY_1       /*!< FLASH Two Latency cycles */
+
+/**
+  * @}
+  */
+
+#else
+/** @defgroup FLASH_Latency FLASH Latency
+  * @{
+  */
+#define FLASH_LATENCY_0            0x00000000U    /*!< FLASH Zero Latency cycle */
+
+/**
+  * @}
+  */
+
+#endif /* FLASH_ACR_LATENCY */
+/**
+  * @}
+  */  
+  
+/* Exported macro ------------------------------------------------------------*/
+
+/** @defgroup FLASH_Exported_Macros FLASH Exported Macros
+ *  @brief macros to control FLASH features 
+ *  @{
+ */
+ 
+/** @defgroup FLASH_Half_Cycle FLASH Half Cycle
+ *  @brief macros to handle FLASH half cycle
+ * @{
+ */
+
+/**
+  * @brief  Enable the FLASH half cycle access.
+  * @note   half cycle access can only be used with a low-frequency clock of less than
+            8 MHz that can be obtained with the use of HSI or HSE but not of PLL.
+  * @retval None
+  */
+#define __HAL_FLASH_HALF_CYCLE_ACCESS_ENABLE()  (FLASH->ACR |= FLASH_ACR_HLFCYA)
+
+/**
+  * @brief  Disable the FLASH half cycle access.
+  * @note   half cycle access can only be used with a low-frequency clock of less than
+            8 MHz that can be obtained with the use of HSI or HSE but not of PLL.
+  * @retval None
+  */
+#define __HAL_FLASH_HALF_CYCLE_ACCESS_DISABLE() (FLASH->ACR &= (~FLASH_ACR_HLFCYA))
+
+/**
+  * @}
+  */
+
+#if defined(FLASH_ACR_LATENCY)
+/** @defgroup FLASH_EM_Latency FLASH Latency
+ *  @brief macros to handle FLASH Latency
+ * @{
+ */ 
+  
+/**
+  * @brief  Set the FLASH Latency.
+  * @param  __LATENCY__ FLASH Latency                   
+  *         The value of this parameter depend on device used within the same series
+  * @retval None
+  */ 
+#define __HAL_FLASH_SET_LATENCY(__LATENCY__)    (FLASH->ACR = (FLASH->ACR&(~FLASH_ACR_LATENCY)) | (__LATENCY__))
+
+
+/**
+  * @brief  Get the FLASH Latency.
+  * @retval FLASH Latency                   
+  *         The value of this parameter depend on device used within the same series
+  */ 
+#define __HAL_FLASH_GET_LATENCY()     (READ_BIT((FLASH->ACR), FLASH_ACR_LATENCY))
+
+/**
+  * @}
+  */
+
+#endif /* FLASH_ACR_LATENCY */
+/** @defgroup FLASH_Prefetch FLASH Prefetch
+ *  @brief macros to handle FLASH Prefetch buffer
+ * @{
+ */   
+/**
+  * @brief  Enable the FLASH prefetch buffer.
+  * @retval None
+  */ 
+#define __HAL_FLASH_PREFETCH_BUFFER_ENABLE()    (FLASH->ACR |= FLASH_ACR_PRFTBE)
+
+/**
+  * @brief  Disable the FLASH prefetch buffer.
+  * @retval None
+  */
+#define __HAL_FLASH_PREFETCH_BUFFER_DISABLE()   (FLASH->ACR &= (~FLASH_ACR_PRFTBE))
+
+/**
+  * @}
+  */
+  
+/**
+  * @}
+  */ 
+
+/* Include FLASH HAL Extended module */
+#include "stm32f1xx_hal_flash_ex.h"  
+
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup FLASH_Exported_Functions
+  * @{
+  */
+  
+/** @addtogroup FLASH_Exported_Functions_Group1
+  * @{
+  */
+/* IO operation functions *****************************************************/
+HAL_StatusTypeDef HAL_FLASH_Program(uint32_t TypeProgram, uint32_t Address, uint64_t Data);
+HAL_StatusTypeDef HAL_FLASH_Program_IT(uint32_t TypeProgram, uint32_t Address, uint64_t Data);
+
+/* FLASH IRQ handler function */
+void       HAL_FLASH_IRQHandler(void);
+/* Callbacks in non blocking modes */ 
+void       HAL_FLASH_EndOfOperationCallback(uint32_t ReturnValue);
+void       HAL_FLASH_OperationErrorCallback(uint32_t ReturnValue);
+
+/**
+  * @}
+  */
+
+/** @addtogroup FLASH_Exported_Functions_Group2
+  * @{
+  */
+/* Peripheral Control functions ***********************************************/
+HAL_StatusTypeDef HAL_FLASH_Unlock(void);
+HAL_StatusTypeDef HAL_FLASH_Lock(void);
+HAL_StatusTypeDef HAL_FLASH_OB_Unlock(void);
+HAL_StatusTypeDef HAL_FLASH_OB_Lock(void);
+void HAL_FLASH_OB_Launch(void);
+
+/**
+  * @}
+  */
+
+/** @addtogroup FLASH_Exported_Functions_Group3
+  * @{
+  */
+/* Peripheral State and Error functions ***************************************/
+uint32_t HAL_FLASH_GetError(void);
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Private function -------------------------------------------------*/
+/** @addtogroup FLASH_Private_Functions
+ * @{
+ */
+HAL_StatusTypeDef       FLASH_WaitForLastOperation(uint32_t Timeout);
+#if defined(FLASH_BANK2_END)
+HAL_StatusTypeDef       FLASH_WaitForLastOperationBank2(uint32_t Timeout);
+#endif /* FLASH_BANK2_END */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F1xx_HAL_FLASH_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
+

Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_flash_ex.h

@@ -0,0 +1,786 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_hal_flash_ex.h
+  * @author  MCD Application Team
+  * @brief   Header file of Flash HAL Extended module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F1xx_HAL_FLASH_EX_H
+#define __STM32F1xx_HAL_FLASH_EX_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_hal_def.h"
+
+/** @addtogroup STM32F1xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup FLASHEx
+  * @{
+  */ 
+
+/** @addtogroup FLASHEx_Private_Constants
+  * @{
+  */
+
+#define FLASH_SIZE_DATA_REGISTER     0x1FFFF7E0U
+#define OBR_REG_INDEX                1U
+#define SR_FLAG_MASK                 ((uint32_t)(FLASH_SR_BSY | FLASH_SR_PGERR | FLASH_SR_WRPRTERR | FLASH_SR_EOP))
+
+/**
+  * @}
+  */  
+
+/** @addtogroup FLASHEx_Private_Macros
+  * @{
+  */
+
+#define IS_FLASH_TYPEERASE(VALUE)   (((VALUE) == FLASH_TYPEERASE_PAGES) || ((VALUE) == FLASH_TYPEERASE_MASSERASE))
+
+#define IS_OPTIONBYTE(VALUE)        (((VALUE) <= (OPTIONBYTE_WRP | OPTIONBYTE_RDP | OPTIONBYTE_USER | OPTIONBYTE_DATA)))
+
+#define IS_WRPSTATE(VALUE)          (((VALUE) == OB_WRPSTATE_DISABLE) || ((VALUE) == OB_WRPSTATE_ENABLE))
+
+#define IS_OB_RDP_LEVEL(LEVEL)      (((LEVEL) == OB_RDP_LEVEL_0) || ((LEVEL) == OB_RDP_LEVEL_1))
+
+#define IS_OB_DATA_ADDRESS(ADDRESS) (((ADDRESS) == OB_DATA_ADDRESS_DATA0) || ((ADDRESS) == OB_DATA_ADDRESS_DATA1)) 
+
+#define IS_OB_IWDG_SOURCE(SOURCE)   (((SOURCE) == OB_IWDG_SW) || ((SOURCE) == OB_IWDG_HW))
+
+#define IS_OB_STOP_SOURCE(SOURCE)   (((SOURCE) == OB_STOP_NO_RST) || ((SOURCE) == OB_STOP_RST))
+
+#define IS_OB_STDBY_SOURCE(SOURCE)  (((SOURCE) == OB_STDBY_NO_RST) || ((SOURCE) == OB_STDBY_RST))
+
+#if defined(FLASH_BANK2_END)
+#define IS_OB_BOOT1(BOOT1)         (((BOOT1) == OB_BOOT1_RESET) || ((BOOT1) == OB_BOOT1_SET))
+#endif /* FLASH_BANK2_END */
+
+/* Low Density */
+#if (defined(STM32F101x6) || defined(STM32F102x6) || defined(STM32F103x6))
+#define IS_FLASH_NB_PAGES(ADDRESS,NBPAGES) (((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) == 0x20U) ? ((ADDRESS)+((NBPAGES)*FLASH_PAGE_SIZE)- 1 <= 0x08007FFFU) : \
+                                           ((ADDRESS)+((NBPAGES)*FLASH_PAGE_SIZE)- 1 <= 0x08003FFFU))
+#endif /* STM32F101x6 || STM32F102x6 || STM32F103x6 */
+
+/* Medium Density */
+#if (defined(STM32F100xB) || defined(STM32F101xB) || defined(STM32F102xB) || defined(STM32F103xB))
+#define IS_FLASH_NB_PAGES(ADDRESS,NBPAGES) (((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) == 0x80U) ? ((ADDRESS)+((NBPAGES)*FLASH_PAGE_SIZE)-1 <= 0x0801FFFFU) : \
+                                           (((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) == 0x40U) ? ((ADDRESS)+((NBPAGES)*FLASH_PAGE_SIZE)-1 <= 0x0800FFFFU) : \
+                                           (((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) == 0x20U) ? ((ADDRESS)+((NBPAGES)*FLASH_PAGE_SIZE)-1 <= 0x08007FFFU) : \
+                                           ((ADDRESS)+((NBPAGES)*FLASH_PAGE_SIZE)-1 <= 0x08003FFFU))))
+#endif /* STM32F100xB || STM32F101xB || STM32F102xB || STM32F103xB*/
+
+/* High Density */
+#if (defined(STM32F100xE) || defined(STM32F101xE) || defined(STM32F103xE))
+#define IS_FLASH_NB_PAGES(ADDRESS,NBPAGES) (((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) == 0x200U) ? ((ADDRESS)+((NBPAGES)*FLASH_PAGE_SIZE)-1 <= 0x0807FFFFU) : \
+                                           (((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) == 0x180U) ? ((ADDRESS)+((NBPAGES)*FLASH_PAGE_SIZE)-1 <= 0x0805FFFFU) : \
+                                           ((ADDRESS)+((NBPAGES)*FLASH_PAGE_SIZE)-1 <= 0x0803FFFFU)))
+#endif /* STM32F100xE || STM32F101xE || STM32F103xE */
+
+/* XL Density */
+#if defined(FLASH_BANK2_END)
+#define IS_FLASH_NB_PAGES(ADDRESS,NBPAGES) (((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) == 0x400U) ? ((ADDRESS)+((NBPAGES)*FLASH_PAGE_SIZE)-1 <= 0x080FFFFFU) : \
+                                           ((ADDRESS)+((NBPAGES)*FLASH_PAGE_SIZE)-1 <= 0x080BFFFFU))
+#endif /* FLASH_BANK2_END */
+
+/* Connectivity Line */
+#if (defined(STM32F105xC) || defined(STM32F107xC))
+#define IS_FLASH_NB_PAGES(ADDRESS,NBPAGES) (((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) == 0x100U) ? ((ADDRESS)+((NBPAGES)*FLASH_PAGE_SIZE)-1 <= 0x0803FFFFU) : \
+                                           (((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) ==  0x80U) ? ((ADDRESS)+((NBPAGES)*FLASH_PAGE_SIZE)-1 <= 0x0801FFFFU) : \
+                                           ((ADDRESS)+((NBPAGES)*FLASH_PAGE_SIZE)-1 <= 0x0800FFFFU)))
+#endif /* STM32F105xC || STM32F107xC */
+
+#define IS_OB_WRP(PAGE) (((PAGE) != 0x0000000U))
+
+#if defined(FLASH_BANK2_END)
+#define IS_FLASH_BANK(BANK) (((BANK) == FLASH_BANK_1)  || \
+                             ((BANK) == FLASH_BANK_2)  || \
+                             ((BANK) == FLASH_BANK_BOTH))
+#else
+#define IS_FLASH_BANK(BANK) (((BANK) == FLASH_BANK_1))
+#endif /* FLASH_BANK2_END */
+
+/* Low Density */
+#if (defined(STM32F101x6) || defined(STM32F102x6) || defined(STM32F103x6))
+#define IS_FLASH_PROGRAM_ADDRESS(ADDRESS)  (((ADDRESS) >= FLASH_BASE) && (((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) == 0x20U) ? \
+                                            ((ADDRESS) <= FLASH_BANK1_END) :  ((ADDRESS) <= 0x08003FFFU)))
+
+#endif /* STM32F101x6 || STM32F102x6 || STM32F103x6 */
+
+/* Medium Density */
+#if (defined(STM32F100xB) || defined(STM32F101xB) || defined(STM32F102xB) || defined(STM32F103xB))
+#define IS_FLASH_PROGRAM_ADDRESS(ADDRESS) (((ADDRESS) >= FLASH_BASE) && (((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) == 0x80U) ? \
+                                           ((ADDRESS) <= FLASH_BANK1_END) :  (((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) == 0x40U) ? \
+                                           ((ADDRESS) <= 0x0800FFFF) :  (((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) == 0x20U) ? \
+                                           ((ADDRESS) <= 0x08007FFF) :  ((ADDRESS) <= 0x08003FFFU)))))
+
+#endif /* STM32F100xB || STM32F101xB || STM32F102xB || STM32F103xB*/
+
+/* High Density */
+#if (defined(STM32F100xE) || defined(STM32F101xE) || defined(STM32F103xE))
+#define IS_FLASH_PROGRAM_ADDRESS(ADDRESS) (((ADDRESS) >= FLASH_BASE) && (((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) == 0x200U) ? \
+                                           ((ADDRESS) <= FLASH_BANK1_END) :  (((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) == 0x180U) ? \
+                                           ((ADDRESS) <= 0x0805FFFFU) :  ((ADDRESS) <= 0x0803FFFFU))))
+
+#endif /* STM32F100xE || STM32F101xE || STM32F103xE */
+
+/* XL Density */
+#if defined(FLASH_BANK2_END)
+#define IS_FLASH_PROGRAM_ADDRESS(ADDRESS) (((ADDRESS) >= FLASH_BASE) && (((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) == 0x400U) ? \
+                                           ((ADDRESS) <= FLASH_BANK2_END) :  ((ADDRESS) <= 0x080BFFFFU)))
+
+#endif /* FLASH_BANK2_END */
+
+/* Connectivity Line */
+#if (defined(STM32F105xC) || defined(STM32F107xC))
+#define IS_FLASH_PROGRAM_ADDRESS(ADDRESS) (((ADDRESS) >= FLASH_BASE) && (((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) == 0x100U) ? \
+                                           ((ADDRESS) <= FLASH_BANK1_END) :  (((*((uint16_t *)FLASH_SIZE_DATA_REGISTER)) == 0x80U) ? \
+                                           ((ADDRESS) <= 0x0801FFFFU) :  ((ADDRESS) <= 0x0800FFFFU))))
+
+#endif /* STM32F105xC || STM32F107xC */
+
+/**
+  * @}
+  */  
+
+/* Exported types ------------------------------------------------------------*/ 
+/** @defgroup FLASHEx_Exported_Types FLASHEx Exported Types
+  * @{
+  */  
+
+/**
+  * @brief  FLASH Erase structure definition
+  */
+typedef struct
+{
+  uint32_t TypeErase;   /*!< TypeErase: Mass erase or page erase.
+                             This parameter can be a value of @ref FLASHEx_Type_Erase */
+  
+  uint32_t Banks;       /*!< Select banks to erase when Mass erase is enabled.
+                             This parameter must be a value of @ref FLASHEx_Banks */    
+  
+  uint32_t PageAddress; /*!< PageAdress: Initial FLASH page address to erase when mass erase is disabled
+                             This parameter must be a number between Min_Data = 0x08000000 and Max_Data = FLASH_BANKx_END 
+                             (x = 1 or 2 depending on devices)*/
+  
+  uint32_t NbPages;     /*!< NbPages: Number of pagess to be erased.
+                             This parameter must be a value between Min_Data = 1 and Max_Data = (max number of pages - value of initial page)*/
+                                                          
+} FLASH_EraseInitTypeDef;
+
+/**
+  * @brief  FLASH Options bytes program structure definition
+  */
+typedef struct
+{
+  uint32_t OptionType;  /*!< OptionType: Option byte to be configured.
+                             This parameter can be a value of @ref FLASHEx_OB_Type */
+
+  uint32_t WRPState;    /*!< WRPState: Write protection activation or deactivation.
+                             This parameter can be a value of @ref FLASHEx_OB_WRP_State */
+
+  uint32_t WRPPage;     /*!< WRPPage: specifies the page(s) to be write protected
+                             This parameter can be a value of @ref FLASHEx_OB_Write_Protection */
+
+  uint32_t Banks;        /*!< Select banks for WRP activation/deactivation of all sectors.
+                              This parameter must be a value of @ref FLASHEx_Banks */ 
+    
+  uint8_t RDPLevel;     /*!< RDPLevel: Set the read protection level..
+                             This parameter can be a value of @ref FLASHEx_OB_Read_Protection */
+
+#if defined(FLASH_BANK2_END)
+  uint8_t USERConfig;   /*!< USERConfig: Program the FLASH User Option Byte: 
+                             IWDG / STOP / STDBY / BOOT1
+                             This parameter can be a combination of @ref FLASHEx_OB_IWatchdog, @ref FLASHEx_OB_nRST_STOP, 
+                             @ref FLASHEx_OB_nRST_STDBY, @ref FLASHEx_OB_BOOT1 */
+#else
+  uint8_t USERConfig;   /*!< USERConfig: Program the FLASH User Option Byte: 
+                             IWDG / STOP / STDBY
+                             This parameter can be a combination of @ref FLASHEx_OB_IWatchdog, @ref FLASHEx_OB_nRST_STOP, 
+                             @ref FLASHEx_OB_nRST_STDBY */
+#endif /* FLASH_BANK2_END */
+
+  uint32_t DATAAddress; /*!< DATAAddress: Address of the option byte DATA to be programmed
+                             This parameter can be a value of @ref FLASHEx_OB_Data_Address */
+  
+  uint8_t DATAData;     /*!< DATAData: Data to be stored in the option byte DATA
+                             This parameter must be a number between Min_Data = 0x00 and Max_Data = 0xFF */
+} FLASH_OBProgramInitTypeDef;
+
+/**
+  * @}
+  */
+
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup FLASHEx_Exported_Constants FLASHEx Exported Constants
+  * @{
+  */  
+
+/** @defgroup FLASHEx_Constants FLASH Constants
+  * @{
+  */ 
+
+/** @defgroup FLASHEx_Page_Size Page Size
+  * @{
+  */ 
+#if (defined(STM32F101x6) || defined(STM32F102x6) || defined(STM32F103x6) || defined(STM32F100xB) || defined(STM32F101xB) || defined(STM32F102xB) || defined(STM32F103xB))
+#define FLASH_PAGE_SIZE          0x400U
+#endif /* STM32F101x6 || STM32F102x6 || STM32F103x6 */
+       /* STM32F100xB || STM32F101xB || STM32F102xB || STM32F103xB */
+
+#if (defined(STM32F100xE) || defined(STM32F101xE) || defined(STM32F103xE) || defined(STM32F101xG) || defined(STM32F103xG) || defined(STM32F105xC) || defined(STM32F107xC))
+#define FLASH_PAGE_SIZE          0x800U
+#endif /* STM32F100xB || STM32F101xB || STM32F102xB || STM32F103xB */
+       /* STM32F101xG || STM32F103xG */ 
+       /* STM32F105xC || STM32F107xC */
+
+/**
+  * @}
+  */
+
+/** @defgroup FLASHEx_Type_Erase Type Erase
+  * @{
+  */ 
+#define FLASH_TYPEERASE_PAGES     0x00U  /*!<Pages erase only*/
+#define FLASH_TYPEERASE_MASSERASE 0x02U  /*!<Flash mass erase activation*/
+
+/**
+  * @}
+  */
+
+/** @defgroup FLASHEx_Banks Banks
+  * @{
+  */
+#if defined(FLASH_BANK2_END)
+#define FLASH_BANK_1     1U /*!< Bank 1   */
+#define FLASH_BANK_2     2U /*!< Bank 2   */
+#define FLASH_BANK_BOTH  ((uint32_t)FLASH_BANK_1 | FLASH_BANK_2) /*!< Bank1 and Bank2  */
+
+#else
+#define FLASH_BANK_1     1U /*!< Bank 1   */
+#endif
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup FLASHEx_OptionByte_Constants Option Byte Constants
+  * @{
+  */ 
+
+/** @defgroup FLASHEx_OB_Type Option Bytes Type
+  * @{
+  */
+#define OPTIONBYTE_WRP            0x01U  /*!<WRP option byte configuration*/
+#define OPTIONBYTE_RDP            0x02U  /*!<RDP option byte configuration*/
+#define OPTIONBYTE_USER           0x04U  /*!<USER option byte configuration*/
+#define OPTIONBYTE_DATA           0x08U  /*!<DATA option byte configuration*/
+
+/**
+  * @}
+  */
+
+/** @defgroup FLASHEx_OB_WRP_State Option Byte WRP State
+  * @{
+  */ 
+#define OB_WRPSTATE_DISABLE       0x00U  /*!<Disable the write protection of the desired pages*/
+#define OB_WRPSTATE_ENABLE        0x01U  /*!<Enable the write protection of the desired pagess*/
+
+/**
+  * @}
+  */
+
+/** @defgroup FLASHEx_OB_Write_Protection Option Bytes Write Protection
+  * @{
+  */
+/* STM32 Low and Medium density devices */
+#if  defined(STM32F101x6) || defined(STM32F102x6) || defined(STM32F103x6) \
+  || defined(STM32F100xB) || defined(STM32F101xB) || defined(STM32F102xB) \
+  || defined(STM32F103xB)
+#define OB_WRP_PAGES0TO3               0x00000001U /*!< Write protection of page 0 to 3 */
+#define OB_WRP_PAGES4TO7               0x00000002U /*!< Write protection of page 4 to 7 */
+#define OB_WRP_PAGES8TO11              0x00000004U /*!< Write protection of page 8 to 11 */
+#define OB_WRP_PAGES12TO15             0x00000008U /*!< Write protection of page 12 to 15 */
+#define OB_WRP_PAGES16TO19             0x00000010U /*!< Write protection of page 16 to 19 */
+#define OB_WRP_PAGES20TO23             0x00000020U /*!< Write protection of page 20 to 23 */
+#define OB_WRP_PAGES24TO27             0x00000040U /*!< Write protection of page 24 to 27 */
+#define OB_WRP_PAGES28TO31             0x00000080U /*!< Write protection of page 28 to 31 */
+#endif /* STM32F101x6 || STM32F102x6 || STM32F103x6 */
+       /* STM32F100xB || STM32F101xB || STM32F102xB || STM32F103xB */
+       
+/* STM32 Medium-density devices */
+#if  defined(STM32F100xB) || defined(STM32F101xB) || defined(STM32F102xB) || defined(STM32F103xB)
+#define OB_WRP_PAGES32TO35             0x00000100U   /*!< Write protection of page 32 to 35 */
+#define OB_WRP_PAGES36TO39             0x00000200U   /*!< Write protection of page 36 to 39 */
+#define OB_WRP_PAGES40TO43             0x00000400U   /*!< Write protection of page 40 to 43 */
+#define OB_WRP_PAGES44TO47             0x00000800U   /*!< Write protection of page 44 to 47 */
+#define OB_WRP_PAGES48TO51             0x00001000U   /*!< Write protection of page 48 to 51 */
+#define OB_WRP_PAGES52TO55             0x00002000U   /*!< Write protection of page 52 to 55 */
+#define OB_WRP_PAGES56TO59             0x00004000U   /*!< Write protection of page 56 to 59 */
+#define OB_WRP_PAGES60TO63             0x00008000U   /*!< Write protection of page 60 to 63 */
+#define OB_WRP_PAGES64TO67             0x00010000U   /*!< Write protection of page 64 to 67 */
+#define OB_WRP_PAGES68TO71             0x00020000U   /*!< Write protection of page 68 to 71 */
+#define OB_WRP_PAGES72TO75             0x00040000U   /*!< Write protection of page 72 to 75 */
+#define OB_WRP_PAGES76TO79             0x00080000U   /*!< Write protection of page 76 to 79 */
+#define OB_WRP_PAGES80TO83             0x00100000U   /*!< Write protection of page 80 to 83 */
+#define OB_WRP_PAGES84TO87             0x00200000U   /*!< Write protection of page 84 to 87 */
+#define OB_WRP_PAGES88TO91             0x00400000U   /*!< Write protection of page 88 to 91 */
+#define OB_WRP_PAGES92TO95             0x00800000U   /*!< Write protection of page 92 to 95 */
+#define OB_WRP_PAGES96TO99             0x01000000U   /*!< Write protection of page 96 to 99 */
+#define OB_WRP_PAGES100TO103           0x02000000U   /*!< Write protection of page 100 to 103 */
+#define OB_WRP_PAGES104TO107           0x04000000U   /*!< Write protection of page 104 to 107 */
+#define OB_WRP_PAGES108TO111           0x08000000U   /*!< Write protection of page 108 to 111 */
+#define OB_WRP_PAGES112TO115           0x10000000U   /*!< Write protection of page 112 to 115 */
+#define OB_WRP_PAGES116TO119           0x20000000U   /*!< Write protection of page 115 to 119 */
+#define OB_WRP_PAGES120TO123           0x40000000U   /*!< Write protection of page 120 to 123 */
+#define OB_WRP_PAGES124TO127           0x80000000U    /*!< Write protection of page 124 to 127 */
+#endif /* STM32F100xB || STM32F101xB || STM32F102xB || STM32F103xB */
+
+
+/* STM32 High-density, XL-density and Connectivity line devices */
+#if  defined(STM32F100xE) || defined(STM32F101xE) || defined(STM32F103xE) \
+  || defined(STM32F101xG) || defined(STM32F103xG) \
+  || defined(STM32F105xC) || defined(STM32F107xC)
+#define OB_WRP_PAGES0TO1               0x00000001U  /*!< Write protection of page 0 TO 1 */
+#define OB_WRP_PAGES2TO3               0x00000002U  /*!< Write protection of page 2 TO 3 */
+#define OB_WRP_PAGES4TO5               0x00000004U  /*!< Write protection of page 4 TO 5 */
+#define OB_WRP_PAGES6TO7               0x00000008U  /*!< Write protection of page 6 TO 7 */
+#define OB_WRP_PAGES8TO9               0x00000010U  /*!< Write protection of page 8 TO 9 */
+#define OB_WRP_PAGES10TO11             0x00000020U  /*!< Write protection of page 10 TO 11 */
+#define OB_WRP_PAGES12TO13             0x00000040U  /*!< Write protection of page 12 TO 13 */
+#define OB_WRP_PAGES14TO15             0x00000080U  /*!< Write protection of page 14 TO 15 */
+#define OB_WRP_PAGES16TO17             0x00000100U  /*!< Write protection of page 16 TO 17 */
+#define OB_WRP_PAGES18TO19             0x00000200U  /*!< Write protection of page 18 TO 19 */
+#define OB_WRP_PAGES20TO21             0x00000400U  /*!< Write protection of page 20 TO 21 */
+#define OB_WRP_PAGES22TO23             0x00000800U  /*!< Write protection of page 22 TO 23 */
+#define OB_WRP_PAGES24TO25             0x00001000U  /*!< Write protection of page 24 TO 25 */
+#define OB_WRP_PAGES26TO27             0x00002000U  /*!< Write protection of page 26 TO 27 */
+#define OB_WRP_PAGES28TO29             0x00004000U  /*!< Write protection of page 28 TO 29 */
+#define OB_WRP_PAGES30TO31             0x00008000U  /*!< Write protection of page 30 TO 31 */
+#define OB_WRP_PAGES32TO33             0x00010000U  /*!< Write protection of page 32 TO 33 */
+#define OB_WRP_PAGES34TO35             0x00020000U  /*!< Write protection of page 34 TO 35 */
+#define OB_WRP_PAGES36TO37             0x00040000U  /*!< Write protection of page 36 TO 37 */
+#define OB_WRP_PAGES38TO39             0x00080000U  /*!< Write protection of page 38 TO 39 */
+#define OB_WRP_PAGES40TO41             0x00100000U  /*!< Write protection of page 40 TO 41 */
+#define OB_WRP_PAGES42TO43             0x00200000U  /*!< Write protection of page 42 TO 43 */
+#define OB_WRP_PAGES44TO45             0x00400000U  /*!< Write protection of page 44 TO 45 */
+#define OB_WRP_PAGES46TO47             0x00800000U  /*!< Write protection of page 46 TO 47 */
+#define OB_WRP_PAGES48TO49             0x01000000U  /*!< Write protection of page 48 TO 49 */
+#define OB_WRP_PAGES50TO51             0x02000000U  /*!< Write protection of page 50 TO 51 */
+#define OB_WRP_PAGES52TO53             0x04000000U  /*!< Write protection of page 52 TO 53 */
+#define OB_WRP_PAGES54TO55             0x08000000U  /*!< Write protection of page 54 TO 55 */
+#define OB_WRP_PAGES56TO57             0x10000000U  /*!< Write protection of page 56 TO 57 */
+#define OB_WRP_PAGES58TO59             0x20000000U  /*!< Write protection of page 58 TO 59 */
+#define OB_WRP_PAGES60TO61             0x40000000U  /*!< Write protection of page 60 TO 61 */
+#define OB_WRP_PAGES62TO127            0x80000000U   /*!< Write protection of page 62 TO 127 */
+#define OB_WRP_PAGES62TO255            0x80000000U   /*!< Write protection of page 62 TO 255 */
+#define OB_WRP_PAGES62TO511            0x80000000U   /*!< Write protection of page 62 TO 511 */
+#endif /* STM32F100xB || STM32F101xB || STM32F102xB || STM32F103xB */
+       /* STM32F101xG || STM32F103xG */ 
+       /* STM32F105xC || STM32F107xC */
+
+#define OB_WRP_ALLPAGES                0xFFFFFFFFU  /*!< Write protection of all Pages */
+ 
+/* Low Density */
+#if  defined(STM32F101x6) || defined(STM32F102x6) || defined(STM32F103x6)
+#define OB_WRP_PAGES0TO31MASK          0x000000FFU 
+#endif /* STM32F101x6 || STM32F102x6 || STM32F103x6 */
+
+/* Medium Density */
+#if  defined(STM32F100xB) || defined(STM32F101xB) || defined(STM32F102xB) || defined(STM32F103xB)
+#define OB_WRP_PAGES0TO31MASK          0x000000FFU
+#define OB_WRP_PAGES32TO63MASK         0x0000FF00U
+#define OB_WRP_PAGES64TO95MASK         0x00FF0000U
+#define OB_WRP_PAGES96TO127MASK        0xFF000000U
+#endif /* STM32F100xB || STM32F101xB || STM32F102xB || STM32F103xB*/
+       
+/* High Density */
+#if  defined(STM32F100xE) || defined(STM32F101xE) || defined(STM32F103xE)  
+#define OB_WRP_PAGES0TO15MASK          0x000000FFU
+#define OB_WRP_PAGES16TO31MASK         0x0000FF00U
+#define OB_WRP_PAGES32TO47MASK         0x00FF0000U
+#define OB_WRP_PAGES48TO255MASK        0xFF000000U
+#endif /* STM32F100xE || STM32F101xE || STM32F103xE */
+
+/* XL Density */
+#if  defined(STM32F101xG) || defined(STM32F103xG) 
+#define OB_WRP_PAGES0TO15MASK          0x000000FFU
+#define OB_WRP_PAGES16TO31MASK         0x0000FF00U
+#define OB_WRP_PAGES32TO47MASK         0x00FF0000U
+#define OB_WRP_PAGES48TO511MASK        0xFF000000U
+#endif /* STM32F101xG || STM32F103xG */
+      
+/* Connectivity line devices */
+#if defined(STM32F105xC) || defined(STM32F107xC)
+#define OB_WRP_PAGES0TO15MASK          0x000000FFU
+#define OB_WRP_PAGES16TO31MASK         0x0000FF00U
+#define OB_WRP_PAGES32TO47MASK         0x00FF0000U
+#define OB_WRP_PAGES48TO127MASK        0xFF000000U
+#endif /* STM32F105xC || STM32F107xC */
+
+/**
+  * @}
+  */
+
+/** @defgroup FLASHEx_OB_Read_Protection Option Byte Read Protection
+  * @{
+  */
+#define OB_RDP_LEVEL_0            ((uint8_t)0xA5)
+#define OB_RDP_LEVEL_1            ((uint8_t)0x00)
+/**
+  * @}
+  */
+  
+/** @defgroup FLASHEx_OB_IWatchdog Option Byte IWatchdog
+  * @{
+  */ 
+#define OB_IWDG_SW                ((uint16_t)0x0001)  /*!< Software IWDG selected */
+#define OB_IWDG_HW                ((uint16_t)0x0000)  /*!< Hardware IWDG selected */
+/**
+  * @}
+  */
+
+/** @defgroup FLASHEx_OB_nRST_STOP Option Byte nRST STOP
+  * @{
+  */ 
+#define OB_STOP_NO_RST            ((uint16_t)0x0002) /*!< No reset generated when entering in STOP */
+#define OB_STOP_RST               ((uint16_t)0x0000) /*!< Reset generated when entering in STOP */
+/**
+  * @}
+  */ 
+
+/** @defgroup FLASHEx_OB_nRST_STDBY Option Byte nRST STDBY
+  * @{
+  */ 
+#define OB_STDBY_NO_RST           ((uint16_t)0x0004) /*!< No reset generated when entering in STANDBY */
+#define OB_STDBY_RST              ((uint16_t)0x0000) /*!< Reset generated when entering in STANDBY */
+/**
+  * @}
+  */
+
+#if defined(FLASH_BANK2_END)
+/** @defgroup FLASHEx_OB_BOOT1 Option Byte BOOT1
+  * @{
+  */
+#define OB_BOOT1_RESET            ((uint16_t)0x0000) /*!< BOOT1 Reset */
+#define OB_BOOT1_SET              ((uint16_t)0x0008) /*!< BOOT1 Set */
+/**
+  * @}
+  */
+#endif /* FLASH_BANK2_END */
+
+/** @defgroup FLASHEx_OB_Data_Address  Option Byte Data Address
+  * @{
+  */
+#define OB_DATA_ADDRESS_DATA0     0x1FFFF804U
+#define OB_DATA_ADDRESS_DATA1     0x1FFFF806U
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/** @addtogroup FLASHEx_Constants
+  * @{
+  */ 
+
+/** @defgroup FLASH_Flag_definition Flag definition
+  * @brief Flag definition
+  * @{
+  */
+#if defined(FLASH_BANK2_END)
+ #define FLASH_FLAG_BSY             FLASH_FLAG_BSY_BANK1       /*!< FLASH Bank1 Busy flag                   */ 
+ #define FLASH_FLAG_PGERR           FLASH_FLAG_PGERR_BANK1     /*!< FLASH Bank1 Programming error flag      */
+ #define FLASH_FLAG_WRPERR          FLASH_FLAG_WRPERR_BANK1    /*!< FLASH Bank1 Write protected error flag  */
+ #define FLASH_FLAG_EOP             FLASH_FLAG_EOP_BANK1       /*!< FLASH Bank1 End of Operation flag       */
+
+ #define FLASH_FLAG_BSY_BANK1       FLASH_SR_BSY               /*!< FLASH Bank1 Busy flag                   */ 
+ #define FLASH_FLAG_PGERR_BANK1     FLASH_SR_PGERR             /*!< FLASH Bank1 Programming error flag      */
+ #define FLASH_FLAG_WRPERR_BANK1    FLASH_SR_WRPRTERR          /*!< FLASH Bank1 Write protected error flag  */
+ #define FLASH_FLAG_EOP_BANK1       FLASH_SR_EOP               /*!< FLASH Bank1 End of Operation flag       */
+       
+ #define FLASH_FLAG_BSY_BANK2       (FLASH_SR2_BSY << 16U)      /*!< FLASH Bank2 Busy flag                   */ 
+ #define FLASH_FLAG_PGERR_BANK2     (FLASH_SR2_PGERR << 16U)    /*!< FLASH Bank2 Programming error flag      */
+ #define FLASH_FLAG_WRPERR_BANK2    (FLASH_SR2_WRPRTERR << 16U) /*!< FLASH Bank2 Write protected error flag  */
+ #define FLASH_FLAG_EOP_BANK2       (FLASH_SR2_EOP << 16U)      /*!< FLASH Bank2 End of Operation flag       */
+
+#else  
+
+ #define FLASH_FLAG_BSY             FLASH_SR_BSY              /*!< FLASH Busy flag                          */ 
+ #define FLASH_FLAG_PGERR           FLASH_SR_PGERR            /*!< FLASH Programming error flag             */
+ #define FLASH_FLAG_WRPERR          FLASH_SR_WRPRTERR         /*!< FLASH Write protected error flag         */
+ #define FLASH_FLAG_EOP             FLASH_SR_EOP              /*!< FLASH End of Operation flag              */
+
+#endif
+ #define FLASH_FLAG_OPTVERR         ((OBR_REG_INDEX << 8U | FLASH_OBR_OPTERR)) /*!< Option Byte Error        */
+/**
+  * @}
+  */
+  
+/** @defgroup FLASH_Interrupt_definition Interrupt definition
+  * @brief FLASH Interrupt definition
+  * @{
+  */
+#if defined(FLASH_BANK2_END)
+ #define FLASH_IT_EOP               FLASH_IT_EOP_BANK1        /*!< End of FLASH Operation Interrupt source Bank1 */
+ #define FLASH_IT_ERR               FLASH_IT_ERR_BANK1        /*!< Error Interrupt source Bank1                  */
+
+ #define FLASH_IT_EOP_BANK1         FLASH_CR_EOPIE            /*!< End of FLASH Operation Interrupt source Bank1 */
+ #define FLASH_IT_ERR_BANK1         FLASH_CR_ERRIE            /*!< Error Interrupt source Bank1                  */
+
+ #define FLASH_IT_EOP_BANK2         (FLASH_CR2_EOPIE << 16U)   /*!< End of FLASH Operation Interrupt source Bank2 */
+ #define FLASH_IT_ERR_BANK2         (FLASH_CR2_ERRIE << 16U)   /*!< Error Interrupt source Bank2                  */
+
+#else
+
+ #define FLASH_IT_EOP               FLASH_CR_EOPIE          /*!< End of FLASH Operation Interrupt source */
+ #define FLASH_IT_ERR               FLASH_CR_ERRIE          /*!< Error Interrupt source                  */
+
+#endif
+/**
+  * @}
+  */  
+
+/**
+  * @}
+  */
+  
+
+/**
+  * @}
+  */
+
+/* Exported macro ------------------------------------------------------------*/
+/** @defgroup FLASHEx_Exported_Macros FLASHEx Exported Macros
+  * @{
+  */
+
+/** @defgroup FLASH_Interrupt Interrupt
+ *  @brief macros to handle FLASH interrupts
+ * @{
+ */ 
+
+#if defined(FLASH_BANK2_END)
+/**
+  * @brief  Enable the specified FLASH interrupt.
+  * @param  __INTERRUPT__  FLASH interrupt 
+  *     This parameter can be any combination of the following values:
+  *     @arg @ref FLASH_IT_EOP_BANK1 End of FLASH Operation Interrupt on bank1
+  *     @arg @ref FLASH_IT_ERR_BANK1 Error Interrupt on bank1
+  *     @arg @ref FLASH_IT_EOP_BANK2 End of FLASH Operation Interrupt on bank2
+  *     @arg @ref FLASH_IT_ERR_BANK2 Error Interrupt on bank2
+  * @retval none
+  */ 
+#define __HAL_FLASH_ENABLE_IT(__INTERRUPT__)  do { \
+                          /* Enable Bank1 IT */ \
+                          SET_BIT(FLASH->CR, ((__INTERRUPT__) & 0x0000FFFFU)); \
+                          /* Enable Bank2 IT */ \
+                          SET_BIT(FLASH->CR2, ((__INTERRUPT__) >> 16U)); \
+                    } while(0U)
+
+/**
+  * @brief  Disable the specified FLASH interrupt.
+  * @param  __INTERRUPT__  FLASH interrupt 
+  *     This parameter can be any combination of the following values:
+  *     @arg @ref FLASH_IT_EOP_BANK1 End of FLASH Operation Interrupt on bank1
+  *     @arg @ref FLASH_IT_ERR_BANK1 Error Interrupt on bank1
+  *     @arg @ref FLASH_IT_EOP_BANK2 End of FLASH Operation Interrupt on bank2
+  *     @arg @ref FLASH_IT_ERR_BANK2 Error Interrupt on bank2
+  * @retval none
+  */ 
+#define __HAL_FLASH_DISABLE_IT(__INTERRUPT__)  do { \
+                          /* Disable Bank1 IT */ \
+                          CLEAR_BIT(FLASH->CR, ((__INTERRUPT__) & 0x0000FFFFU)); \
+                          /* Disable Bank2 IT */ \
+                          CLEAR_BIT(FLASH->CR2, ((__INTERRUPT__) >> 16U)); \
+                    } while(0U)
+
+/**
+  * @brief  Get the specified FLASH flag status. 
+  * @param  __FLAG__ specifies the FLASH flag to check.
+  *          This parameter can be one of the following values:
+  *            @arg @ref FLASH_FLAG_EOP_BANK1    FLASH End of Operation flag on bank1
+  *            @arg @ref FLASH_FLAG_WRPERR_BANK1 FLASH Write protected error flag on bank1
+  *            @arg @ref FLASH_FLAG_PGERR_BANK1  FLASH Programming error flag on bank1
+  *            @arg @ref FLASH_FLAG_BSY_BANK1    FLASH Busy flag on bank1
+  *            @arg @ref FLASH_FLAG_EOP_BANK2    FLASH End of Operation flag on bank2
+  *            @arg @ref FLASH_FLAG_WRPERR_BANK2 FLASH Write protected error flag on bank2
+  *            @arg @ref FLASH_FLAG_PGERR_BANK2  FLASH Programming error flag on bank2
+  *            @arg @ref FLASH_FLAG_BSY_BANK2    FLASH Busy flag on bank2
+  *            @arg @ref FLASH_FLAG_OPTVERR  Loaded OB and its complement do not match
+  * @retval The new state of __FLAG__ (SET or RESET).
+  */
+#define __HAL_FLASH_GET_FLAG(__FLAG__) (((__FLAG__) == FLASH_FLAG_OPTVERR) ? \
+                                            (FLASH->OBR & FLASH_OBR_OPTERR) : \
+                                        ((((__FLAG__) & SR_FLAG_MASK) != RESET)? \
+                                            (FLASH->SR & ((__FLAG__) & SR_FLAG_MASK)) : \
+                                            (FLASH->SR2 & ((__FLAG__) >> 16U))))
+
+/**
+  * @brief  Clear the specified FLASH flag.
+  * @param  __FLAG__ specifies the FLASH flags to clear.
+  *          This parameter can be any combination of the following values:
+  *            @arg @ref FLASH_FLAG_EOP_BANK1    FLASH End of Operation flag on bank1
+  *            @arg @ref FLASH_FLAG_WRPERR_BANK1 FLASH Write protected error flag on bank1
+  *            @arg @ref FLASH_FLAG_PGERR_BANK1  FLASH Programming error flag on bank1
+  *            @arg @ref FLASH_FLAG_BSY_BANK1    FLASH Busy flag on bank1
+  *            @arg @ref FLASH_FLAG_EOP_BANK2    FLASH End of Operation flag on bank2
+  *            @arg @ref FLASH_FLAG_WRPERR_BANK2 FLASH Write protected error flag on bank2
+  *            @arg @ref FLASH_FLAG_PGERR_BANK2  FLASH Programming error flag on bank2
+  *            @arg @ref FLASH_FLAG_BSY_BANK2    FLASH Busy flag on bank2
+  *            @arg @ref FLASH_FLAG_OPTVERR  Loaded OB and its complement do not match
+  * @retval none
+  */
+#define __HAL_FLASH_CLEAR_FLAG(__FLAG__)  do { \
+                          /* Clear FLASH_FLAG_OPTVERR flag */ \
+                          if ((__FLAG__) == FLASH_FLAG_OPTVERR) \
+                          { \
+                            CLEAR_BIT(FLASH->OBR, FLASH_OBR_OPTERR); \
+                          } \
+                          else { \
+                          /* Clear Flag in Bank1 */ \
+                          if (((__FLAG__) & SR_FLAG_MASK) != RESET) \
+                          { \
+                            FLASH->SR  = ((__FLAG__) & SR_FLAG_MASK); \
+                          } \
+                          /* Clear Flag in Bank2 */ \
+                          if (((__FLAG__) >> 16U) != RESET) \
+                          { \
+                            FLASH->SR2 = ((__FLAG__) >> 16U); \
+                          } \
+                          } \
+                    } while(0U)
+#else
+/**
+  * @brief  Enable the specified FLASH interrupt.
+  * @param  __INTERRUPT__  FLASH interrupt 
+  *         This parameter can be any combination of the following values:
+  *     @arg @ref FLASH_IT_EOP End of FLASH Operation Interrupt
+  *     @arg @ref FLASH_IT_ERR Error Interrupt    
+  * @retval none
+  */ 
+#define __HAL_FLASH_ENABLE_IT(__INTERRUPT__)  (FLASH->CR |= (__INTERRUPT__))
+
+/**
+  * @brief  Disable the specified FLASH interrupt.
+  * @param  __INTERRUPT__  FLASH interrupt 
+  *         This parameter can be any combination of the following values:
+  *     @arg @ref FLASH_IT_EOP End of FLASH Operation Interrupt
+  *     @arg @ref FLASH_IT_ERR Error Interrupt    
+  * @retval none
+  */ 
+#define __HAL_FLASH_DISABLE_IT(__INTERRUPT__)   (FLASH->CR &= ~(__INTERRUPT__))
+
+/**
+  * @brief  Get the specified FLASH flag status. 
+  * @param  __FLAG__ specifies the FLASH flag to check.
+  *          This parameter can be one of the following values:
+  *            @arg @ref FLASH_FLAG_EOP    FLASH End of Operation flag 
+  *            @arg @ref FLASH_FLAG_WRPERR FLASH Write protected error flag 
+  *            @arg @ref FLASH_FLAG_PGERR  FLASH Programming error flag
+  *            @arg @ref FLASH_FLAG_BSY    FLASH Busy flag
+  *            @arg @ref FLASH_FLAG_OPTVERR  Loaded OB and its complement do not match
+  * @retval The new state of __FLAG__ (SET or RESET).
+  */
+#define __HAL_FLASH_GET_FLAG(__FLAG__)  (((__FLAG__) == FLASH_FLAG_OPTVERR) ? \
+                                            (FLASH->OBR & FLASH_OBR_OPTERR) : \
+                                            (FLASH->SR & (__FLAG__)))
+/**
+  * @brief  Clear the specified FLASH flag.
+  * @param  __FLAG__ specifies the FLASH flags to clear.
+  *          This parameter can be any combination of the following values:
+  *            @arg @ref FLASH_FLAG_EOP    FLASH End of Operation flag 
+  *            @arg @ref FLASH_FLAG_WRPERR FLASH Write protected error flag 
+  *            @arg @ref FLASH_FLAG_PGERR  FLASH Programming error flag 
+  *            @arg @ref FLASH_FLAG_OPTVERR  Loaded OB and its complement do not match
+  * @retval none
+  */
+#define __HAL_FLASH_CLEAR_FLAG(__FLAG__)   do { \
+                          /* Clear FLASH_FLAG_OPTVERR flag */ \
+                          if ((__FLAG__) == FLASH_FLAG_OPTVERR) \
+                          { \
+                            CLEAR_BIT(FLASH->OBR, FLASH_OBR_OPTERR); \
+                          } \
+                          else { \
+                            /* Clear Flag in Bank1 */ \
+                            FLASH->SR  = (__FLAG__); \
+                          } \
+                    } while(0U)
+
+#endif
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup FLASHEx_Exported_Functions
+  * @{
+  */
+
+/** @addtogroup FLASHEx_Exported_Functions_Group1
+  * @{
+  */
+/* IO operation functions *****************************************************/
+HAL_StatusTypeDef  HAL_FLASHEx_Erase(FLASH_EraseInitTypeDef *pEraseInit, uint32_t *PageError);
+HAL_StatusTypeDef  HAL_FLASHEx_Erase_IT(FLASH_EraseInitTypeDef *pEraseInit);
+
+/**
+  * @}
+  */
+
+/** @addtogroup FLASHEx_Exported_Functions_Group2
+  * @{
+  */
+/* Peripheral Control functions ***********************************************/
+HAL_StatusTypeDef  HAL_FLASHEx_OBErase(void);
+HAL_StatusTypeDef  HAL_FLASHEx_OBProgram(FLASH_OBProgramInitTypeDef *pOBInit);
+void               HAL_FLASHEx_OBGetConfig(FLASH_OBProgramInitTypeDef *pOBInit);
+uint32_t           HAL_FLASHEx_OBGetUserData(uint32_t DATAAdress);
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F1xx_HAL_FLASH_EX_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_gpio.h

@@ -0,0 +1,308 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_hal_gpio.h
+  * @author  MCD Application Team
+  * @brief   Header file of GPIO HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef STM32F1xx_HAL_GPIO_H
+#define STM32F1xx_HAL_GPIO_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_hal_def.h"
+
+/** @addtogroup STM32F1xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup GPIO
+  * @{
+  */
+
+/* Exported types ------------------------------------------------------------*/
+/** @defgroup GPIO_Exported_Types GPIO Exported Types
+  * @{
+  */
+
+/**
+  * @brief GPIO Init structure definition
+  */
+typedef struct
+{
+  uint32_t Pin;       /*!< Specifies the GPIO pins to be configured.
+                           This parameter can be any value of @ref GPIO_pins_define */
+
+  uint32_t Mode;      /*!< Specifies the operating mode for the selected pins.
+                           This parameter can be a value of @ref GPIO_mode_define */
+
+  uint32_t Pull;      /*!< Specifies the Pull-up or Pull-Down activation for the selected pins.
+                           This parameter can be a value of @ref GPIO_pull_define */
+
+  uint32_t Speed;     /*!< Specifies the speed for the selected pins.
+                           This parameter can be a value of @ref GPIO_speed_define */
+} GPIO_InitTypeDef;
+
+/**
+  * @brief  GPIO Bit SET and Bit RESET enumeration
+  */
+typedef enum
+{
+  GPIO_PIN_RESET = 0u,
+  GPIO_PIN_SET
+} GPIO_PinState;
+/**
+  * @}
+  */
+
+/* Exported constants --------------------------------------------------------*/
+
+/** @defgroup GPIO_Exported_Constants GPIO Exported Constants
+  * @{
+  */
+
+/** @defgroup GPIO_pins_define GPIO pins define
+  * @{
+  */
+#define GPIO_PIN_0                 ((uint16_t)0x0001)  /* Pin 0 selected    */
+#define GPIO_PIN_1                 ((uint16_t)0x0002)  /* Pin 1 selected    */
+#define GPIO_PIN_2                 ((uint16_t)0x0004)  /* Pin 2 selected    */
+#define GPIO_PIN_3                 ((uint16_t)0x0008)  /* Pin 3 selected    */
+#define GPIO_PIN_4                 ((uint16_t)0x0010)  /* Pin 4 selected    */
+#define GPIO_PIN_5                 ((uint16_t)0x0020)  /* Pin 5 selected    */
+#define GPIO_PIN_6                 ((uint16_t)0x0040)  /* Pin 6 selected    */
+#define GPIO_PIN_7                 ((uint16_t)0x0080)  /* Pin 7 selected    */
+#define GPIO_PIN_8                 ((uint16_t)0x0100)  /* Pin 8 selected    */
+#define GPIO_PIN_9                 ((uint16_t)0x0200)  /* Pin 9 selected    */
+#define GPIO_PIN_10                ((uint16_t)0x0400)  /* Pin 10 selected   */
+#define GPIO_PIN_11                ((uint16_t)0x0800)  /* Pin 11 selected   */
+#define GPIO_PIN_12                ((uint16_t)0x1000)  /* Pin 12 selected   */
+#define GPIO_PIN_13                ((uint16_t)0x2000)  /* Pin 13 selected   */
+#define GPIO_PIN_14                ((uint16_t)0x4000)  /* Pin 14 selected   */
+#define GPIO_PIN_15                ((uint16_t)0x8000)  /* Pin 15 selected   */
+#define GPIO_PIN_All               ((uint16_t)0xFFFF)  /* All pins selected */
+
+#define GPIO_PIN_MASK              0x0000FFFFu /* PIN mask for assert test */
+/**
+  * @}
+  */
+
+/** @defgroup GPIO_mode_define GPIO mode define
+  * @brief GPIO Configuration Mode
+  *        Elements values convention: 0xX0yz00YZ
+  *           - X  : GPIO mode or EXTI Mode
+  *           - y  : External IT or Event trigger detection
+  *           - z  : IO configuration on External IT or Event
+  *           - Y  : Output type (Push Pull or Open Drain)
+  *           - Z  : IO Direction mode (Input, Output, Alternate or Analog)
+  * @{
+  */
+#define  GPIO_MODE_INPUT                        0x00000000u   /*!< Input Floating Mode                   */
+#define  GPIO_MODE_OUTPUT_PP                    0x00000001u   /*!< Output Push Pull Mode                 */
+#define  GPIO_MODE_OUTPUT_OD                    0x00000011u   /*!< Output Open Drain Mode                */
+#define  GPIO_MODE_AF_PP                        0x00000002u   /*!< Alternate Function Push Pull Mode     */
+#define  GPIO_MODE_AF_OD                        0x00000012u   /*!< Alternate Function Open Drain Mode    */
+#define  GPIO_MODE_AF_INPUT                     GPIO_MODE_INPUT          /*!< Alternate Function Input Mode         */
+
+#define  GPIO_MODE_ANALOG                       0x00000003u   /*!< Analog Mode  */
+
+#define  GPIO_MODE_IT_RISING                    0x10110000u   /*!< External Interrupt Mode with Rising edge trigger detection          */
+#define  GPIO_MODE_IT_FALLING                   0x10210000u   /*!< External Interrupt Mode with Falling edge trigger detection         */
+#define  GPIO_MODE_IT_RISING_FALLING            0x10310000u   /*!< External Interrupt Mode with Rising/Falling edge trigger detection  */
+
+#define  GPIO_MODE_EVT_RISING                   0x10120000u   /*!< External Event Mode with Rising edge trigger detection               */
+#define  GPIO_MODE_EVT_FALLING                  0x10220000u   /*!< External Event Mode with Falling edge trigger detection              */
+#define  GPIO_MODE_EVT_RISING_FALLING           0x10320000u   /*!< External Event Mode with Rising/Falling edge trigger detection       */
+
+/**
+  * @}
+  */
+
+/** @defgroup GPIO_speed_define  GPIO speed define
+  * @brief GPIO Output Maximum frequency
+  * @{
+  */
+#define  GPIO_SPEED_FREQ_LOW              (GPIO_CRL_MODE0_1) /*!< Low speed */
+#define  GPIO_SPEED_FREQ_MEDIUM           (GPIO_CRL_MODE0_0) /*!< Medium speed */
+#define  GPIO_SPEED_FREQ_HIGH             (GPIO_CRL_MODE0)   /*!< High speed */
+
+/**
+  * @}
+  */
+
+/** @defgroup GPIO_pull_define GPIO pull define
+  * @brief GPIO Pull-Up or Pull-Down Activation
+  * @{
+  */
+#define  GPIO_NOPULL        0x00000000u   /*!< No Pull-up or Pull-down activation  */
+#define  GPIO_PULLUP        0x00000001u   /*!< Pull-up activation                  */
+#define  GPIO_PULLDOWN      0x00000002u   /*!< Pull-down activation                */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Exported macro ------------------------------------------------------------*/
+/** @defgroup GPIO_Exported_Macros GPIO Exported Macros
+  * @{
+  */
+
+/**
+  * @brief  Checks whether the specified EXTI line flag is set or not.
+  * @param  __EXTI_LINE__: specifies the EXTI line flag to check.
+  *         This parameter can be GPIO_PIN_x where x can be(0..15)
+  * @retval The new state of __EXTI_LINE__ (SET or RESET).
+  */
+#define __HAL_GPIO_EXTI_GET_FLAG(__EXTI_LINE__) (EXTI->PR & (__EXTI_LINE__))
+
+/**
+  * @brief  Clears the EXTI's line pending flags.
+  * @param  __EXTI_LINE__: specifies the EXTI lines flags to clear.
+  *         This parameter can be any combination of GPIO_PIN_x where x can be (0..15)
+  * @retval None
+  */
+#define __HAL_GPIO_EXTI_CLEAR_FLAG(__EXTI_LINE__) (EXTI->PR = (__EXTI_LINE__))
+
+/**
+  * @brief  Checks whether the specified EXTI line is asserted or not.
+  * @param  __EXTI_LINE__: specifies the EXTI line to check.
+  *          This parameter can be GPIO_PIN_x where x can be(0..15)
+  * @retval The new state of __EXTI_LINE__ (SET or RESET).
+  */
+#define __HAL_GPIO_EXTI_GET_IT(__EXTI_LINE__) (EXTI->PR & (__EXTI_LINE__))
+
+/**
+  * @brief  Clears the EXTI's line pending bits.
+  * @param  __EXTI_LINE__: specifies the EXTI lines to clear.
+  *          This parameter can be any combination of GPIO_PIN_x where x can be (0..15)
+  * @retval None
+  */
+#define __HAL_GPIO_EXTI_CLEAR_IT(__EXTI_LINE__) (EXTI->PR = (__EXTI_LINE__))
+
+/**
+  * @brief  Generates a Software interrupt on selected EXTI line.
+  * @param  __EXTI_LINE__: specifies the EXTI line to check.
+  *          This parameter can be GPIO_PIN_x where x can be(0..15)
+  * @retval None
+  */
+#define __HAL_GPIO_EXTI_GENERATE_SWIT(__EXTI_LINE__) (EXTI->SWIER |= (__EXTI_LINE__))
+/**
+  * @}
+  */
+
+/* Include GPIO HAL Extension module */
+#include "stm32f1xx_hal_gpio_ex.h"
+
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup GPIO_Exported_Functions
+  * @{
+  */
+
+/** @addtogroup GPIO_Exported_Functions_Group1
+  * @{
+  */
+/* Initialization and de-initialization functions *****************************/
+void  HAL_GPIO_Init(GPIO_TypeDef  *GPIOx, GPIO_InitTypeDef *GPIO_Init);
+void  HAL_GPIO_DeInit(GPIO_TypeDef  *GPIOx, uint32_t GPIO_Pin);
+/**
+  * @}
+  */
+
+/** @addtogroup GPIO_Exported_Functions_Group2
+  * @{
+  */
+/* IO operation functions *****************************************************/
+GPIO_PinState HAL_GPIO_ReadPin(GPIO_TypeDef *GPIOx, uint16_t GPIO_Pin);
+void HAL_GPIO_WritePin(GPIO_TypeDef *GPIOx, uint16_t GPIO_Pin, GPIO_PinState PinState);
+void HAL_GPIO_TogglePin(GPIO_TypeDef *GPIOx, uint16_t GPIO_Pin);
+HAL_StatusTypeDef HAL_GPIO_LockPin(GPIO_TypeDef *GPIOx, uint16_t GPIO_Pin);
+void HAL_GPIO_EXTI_IRQHandler(uint16_t GPIO_Pin);
+void HAL_GPIO_EXTI_Callback(uint16_t GPIO_Pin);
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+/* Private types -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private constants ---------------------------------------------------------*/
+/** @defgroup GPIO_Private_Constants GPIO Private Constants
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/* Private macros ------------------------------------------------------------*/
+/** @defgroup GPIO_Private_Macros GPIO Private Macros
+  * @{
+  */
+#define IS_GPIO_PIN_ACTION(ACTION) (((ACTION) == GPIO_PIN_RESET) || ((ACTION) == GPIO_PIN_SET))
+#define IS_GPIO_PIN(PIN)           (((((uint32_t)PIN) & GPIO_PIN_MASK ) != 0x00u) && ((((uint32_t)PIN) & ~GPIO_PIN_MASK) == 0x00u))
+#define IS_GPIO_MODE(MODE) (((MODE) == GPIO_MODE_INPUT)              ||\
+                            ((MODE) == GPIO_MODE_OUTPUT_PP)          ||\
+                            ((MODE) == GPIO_MODE_OUTPUT_OD)          ||\
+                            ((MODE) == GPIO_MODE_AF_PP)              ||\
+                            ((MODE) == GPIO_MODE_AF_OD)              ||\
+                            ((MODE) == GPIO_MODE_IT_RISING)          ||\
+                            ((MODE) == GPIO_MODE_IT_FALLING)         ||\
+                            ((MODE) == GPIO_MODE_IT_RISING_FALLING)  ||\
+                            ((MODE) == GPIO_MODE_EVT_RISING)         ||\
+                            ((MODE) == GPIO_MODE_EVT_FALLING)        ||\
+                            ((MODE) == GPIO_MODE_EVT_RISING_FALLING) ||\
+                            ((MODE) == GPIO_MODE_ANALOG))
+#define IS_GPIO_SPEED(SPEED) (((SPEED) == GPIO_SPEED_FREQ_LOW) || \
+                              ((SPEED) == GPIO_SPEED_FREQ_MEDIUM) || ((SPEED) == GPIO_SPEED_FREQ_HIGH))
+#define IS_GPIO_PULL(PULL) (((PULL) == GPIO_NOPULL) || ((PULL) == GPIO_PULLUP) || \
+                            ((PULL) == GPIO_PULLDOWN))
+/**
+  * @}
+  */
+
+/* Private functions ---------------------------------------------------------*/
+/** @defgroup GPIO_Private_Functions GPIO Private Functions
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* STM32F1xx_HAL_GPIO_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_gpio_ex.h

@@ -0,0 +1,894 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_hal_gpio_ex.h
+  * @author  MCD Application Team
+  * @brief   Header file of GPIO HAL Extension module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef STM32F1xx_HAL_GPIO_EX_H
+#define STM32F1xx_HAL_GPIO_EX_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_hal_def.h"
+
+/** @addtogroup STM32F1xx_HAL_Driver
+  * @{
+  */
+
+/** @defgroup GPIOEx GPIOEx
+  * @{
+  */
+/* Exported types ------------------------------------------------------------*/
+/* Exported constants --------------------------------------------------------*/
+
+/** @defgroup GPIOEx_Exported_Constants GPIOEx Exported Constants
+  * @{
+  */
+
+/** @defgroup GPIOEx_EVENTOUT EVENTOUT Cortex Configuration
+  * @brief This section propose definition to use the Cortex EVENTOUT signal.
+  * @{
+  */
+
+/** @defgroup GPIOEx_EVENTOUT_PIN EVENTOUT Pin
+  * @{
+  */
+
+#define AFIO_EVENTOUT_PIN_0  AFIO_EVCR_PIN_PX0 /*!< EVENTOUT on pin 0 */
+#define AFIO_EVENTOUT_PIN_1  AFIO_EVCR_PIN_PX1 /*!< EVENTOUT on pin 1 */
+#define AFIO_EVENTOUT_PIN_2  AFIO_EVCR_PIN_PX2 /*!< EVENTOUT on pin 2 */
+#define AFIO_EVENTOUT_PIN_3  AFIO_EVCR_PIN_PX3 /*!< EVENTOUT on pin 3 */
+#define AFIO_EVENTOUT_PIN_4  AFIO_EVCR_PIN_PX4 /*!< EVENTOUT on pin 4 */
+#define AFIO_EVENTOUT_PIN_5  AFIO_EVCR_PIN_PX5 /*!< EVENTOUT on pin 5 */
+#define AFIO_EVENTOUT_PIN_6  AFIO_EVCR_PIN_PX6 /*!< EVENTOUT on pin 6 */
+#define AFIO_EVENTOUT_PIN_7  AFIO_EVCR_PIN_PX7 /*!< EVENTOUT on pin 7 */
+#define AFIO_EVENTOUT_PIN_8  AFIO_EVCR_PIN_PX8 /*!< EVENTOUT on pin 8 */
+#define AFIO_EVENTOUT_PIN_9  AFIO_EVCR_PIN_PX9 /*!< EVENTOUT on pin 9 */
+#define AFIO_EVENTOUT_PIN_10 AFIO_EVCR_PIN_PX10 /*!< EVENTOUT on pin 10 */
+#define AFIO_EVENTOUT_PIN_11 AFIO_EVCR_PIN_PX11 /*!< EVENTOUT on pin 11 */
+#define AFIO_EVENTOUT_PIN_12 AFIO_EVCR_PIN_PX12 /*!< EVENTOUT on pin 12 */
+#define AFIO_EVENTOUT_PIN_13 AFIO_EVCR_PIN_PX13 /*!< EVENTOUT on pin 13 */
+#define AFIO_EVENTOUT_PIN_14 AFIO_EVCR_PIN_PX14 /*!< EVENTOUT on pin 14 */
+#define AFIO_EVENTOUT_PIN_15 AFIO_EVCR_PIN_PX15 /*!< EVENTOUT on pin 15 */
+
+#define IS_AFIO_EVENTOUT_PIN(__PIN__) (((__PIN__) == AFIO_EVENTOUT_PIN_0) || \
+                                       ((__PIN__) == AFIO_EVENTOUT_PIN_1) || \
+                                       ((__PIN__) == AFIO_EVENTOUT_PIN_2) || \
+                                       ((__PIN__) == AFIO_EVENTOUT_PIN_3) || \
+                                       ((__PIN__) == AFIO_EVENTOUT_PIN_4) || \
+                                       ((__PIN__) == AFIO_EVENTOUT_PIN_5) || \
+                                       ((__PIN__) == AFIO_EVENTOUT_PIN_6) || \
+                                       ((__PIN__) == AFIO_EVENTOUT_PIN_7) || \
+                                       ((__PIN__) == AFIO_EVENTOUT_PIN_8) || \
+                                       ((__PIN__) == AFIO_EVENTOUT_PIN_9) || \
+                                       ((__PIN__) == AFIO_EVENTOUT_PIN_10) || \
+                                       ((__PIN__) == AFIO_EVENTOUT_PIN_11) || \
+                                       ((__PIN__) == AFIO_EVENTOUT_PIN_12) || \
+                                       ((__PIN__) == AFIO_EVENTOUT_PIN_13) || \
+                                       ((__PIN__) == AFIO_EVENTOUT_PIN_14) || \
+                                       ((__PIN__) == AFIO_EVENTOUT_PIN_15))
+/**
+  * @}
+  */
+
+/** @defgroup GPIOEx_EVENTOUT_PORT EVENTOUT Port
+  * @{
+  */
+
+#define AFIO_EVENTOUT_PORT_A AFIO_EVCR_PORT_PA /*!< EVENTOUT on port A */
+#define AFIO_EVENTOUT_PORT_B AFIO_EVCR_PORT_PB /*!< EVENTOUT on port B */
+#define AFIO_EVENTOUT_PORT_C AFIO_EVCR_PORT_PC /*!< EVENTOUT on port C */
+#define AFIO_EVENTOUT_PORT_D AFIO_EVCR_PORT_PD /*!< EVENTOUT on port D */
+#define AFIO_EVENTOUT_PORT_E AFIO_EVCR_PORT_PE /*!< EVENTOUT on port E */
+
+#define IS_AFIO_EVENTOUT_PORT(__PORT__) (((__PORT__) == AFIO_EVENTOUT_PORT_A) || \
+                                         ((__PORT__) == AFIO_EVENTOUT_PORT_B) || \
+                                         ((__PORT__) == AFIO_EVENTOUT_PORT_C) || \
+                                         ((__PORT__) == AFIO_EVENTOUT_PORT_D) || \
+                                         ((__PORT__) == AFIO_EVENTOUT_PORT_E))
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup GPIOEx_AFIO_AF_REMAPPING Alternate Function Remapping
+  * @brief This section propose definition to remap the alternate function to some other port/pins.
+  * @{
+  */
+
+/**
+  * @brief Enable the remapping of SPI1 alternate function NSS, SCK, MISO and MOSI.
+  * @note  ENABLE: Remap     (NSS/PA15, SCK/PB3, MISO/PB4, MOSI/PB5)
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_SPI1_ENABLE()  AFIO_REMAP_ENABLE(AFIO_MAPR_SPI1_REMAP)
+
+/**
+  * @brief Disable the remapping of SPI1 alternate function NSS, SCK, MISO and MOSI.
+  * @note  DISABLE: No remap (NSS/PA4,  SCK/PA5, MISO/PA6, MOSI/PA7)
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_SPI1_DISABLE()  AFIO_REMAP_DISABLE(AFIO_MAPR_SPI1_REMAP)
+
+/**
+  * @brief Enable the remapping of I2C1 alternate function SCL and SDA.
+  * @note  ENABLE: Remap     (SCL/PB8, SDA/PB9)
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_I2C1_ENABLE()  AFIO_REMAP_ENABLE(AFIO_MAPR_I2C1_REMAP)
+
+/**
+  * @brief Disable the remapping of I2C1 alternate function SCL and SDA.
+  * @note  DISABLE: No remap (SCL/PB6, SDA/PB7)
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_I2C1_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_I2C1_REMAP)
+
+/**
+  * @brief Enable the remapping of USART1 alternate function TX and RX.
+  * @note  ENABLE: Remap     (TX/PB6, RX/PB7)
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_USART1_ENABLE()  AFIO_REMAP_ENABLE(AFIO_MAPR_USART1_REMAP)
+
+/**
+  * @brief Disable the remapping of USART1 alternate function TX and RX.
+  * @note  DISABLE: No remap (TX/PA9, RX/PA10)
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_USART1_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_USART1_REMAP)
+
+/**
+  * @brief Enable the remapping of USART2 alternate function CTS, RTS, CK, TX and RX.
+  * @note  ENABLE: Remap     (CTS/PD3, RTS/PD4, TX/PD5, RX/PD6, CK/PD7)
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_USART2_ENABLE()  AFIO_REMAP_ENABLE(AFIO_MAPR_USART2_REMAP)
+
+/**
+  * @brief Disable the remapping of USART2 alternate function CTS, RTS, CK, TX and RX.
+  * @note  DISABLE: No remap (CTS/PA0, RTS/PA1, TX/PA2, RX/PA3, CK/PA4)
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_USART2_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_USART2_REMAP)
+
+/**
+  * @brief Enable the remapping of USART3 alternate function CTS, RTS, CK, TX and RX.
+  * @note  ENABLE: Full remap     (TX/PD8,  RX/PD9,  CK/PD10, CTS/PD11, RTS/PD12)
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_USART3_ENABLE()  AFIO_REMAP_PARTIAL(AFIO_MAPR_USART3_REMAP_FULLREMAP, AFIO_MAPR_USART3_REMAP_FULLREMAP)
+
+/**
+  * @brief Enable the remapping of USART3 alternate function CTS, RTS, CK, TX and RX.
+  * @note  PARTIAL: Partial remap (TX/PC10, RX/PC11, CK/PC12, CTS/PB13, RTS/PB14)
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_USART3_PARTIAL()  AFIO_REMAP_PARTIAL(AFIO_MAPR_USART3_REMAP_PARTIALREMAP, AFIO_MAPR_USART3_REMAP_FULLREMAP)
+
+/**
+  * @brief Disable the remapping of USART3 alternate function CTS, RTS, CK, TX and RX.
+  * @note  DISABLE: No remap      (TX/PB10, RX/PB11, CK/PB12, CTS/PB13, RTS/PB14)
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_USART3_DISABLE()  AFIO_REMAP_PARTIAL(AFIO_MAPR_USART3_REMAP_NOREMAP, AFIO_MAPR_USART3_REMAP_FULLREMAP)
+
+/**
+  * @brief Enable the remapping of TIM1 alternate function channels 1 to 4, 1N to 3N, external trigger (ETR) and Break input (BKIN)
+  * @note  ENABLE: Full remap     (ETR/PE7,  CH1/PE9, CH2/PE11, CH3/PE13, CH4/PE14, BKIN/PE15, CH1N/PE8,  CH2N/PE10, CH3N/PE12)
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_TIM1_ENABLE()  AFIO_REMAP_PARTIAL(AFIO_MAPR_TIM1_REMAP_FULLREMAP, AFIO_MAPR_TIM1_REMAP_FULLREMAP)
+
+/**
+  * @brief Enable the remapping of TIM1 alternate function channels 1 to 4, 1N to 3N, external trigger (ETR) and Break input (BKIN)
+  * @note  PARTIAL: Partial remap (ETR/PA12, CH1/PA8, CH2/PA9,  CH3/PA10, CH4/PA11, BKIN/PA6,  CH1N/PA7,  CH2N/PB0,  CH3N/PB1)
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_TIM1_PARTIAL()  AFIO_REMAP_PARTIAL(AFIO_MAPR_TIM1_REMAP_PARTIALREMAP, AFIO_MAPR_TIM1_REMAP_FULLREMAP)
+
+/**
+  * @brief Disable the remapping of TIM1 alternate function channels 1 to 4, 1N to 3N, external trigger (ETR) and Break input (BKIN)
+  * @note  DISABLE: No remap      (ETR/PA12, CH1/PA8, CH2/PA9,  CH3/PA10, CH4/PA11, BKIN/PB12, CH1N/PB13, CH2N/PB14, CH3N/PB15)
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_TIM1_DISABLE()  AFIO_REMAP_PARTIAL(AFIO_MAPR_TIM1_REMAP_NOREMAP, AFIO_MAPR_TIM1_REMAP_FULLREMAP)
+
+/**
+  * @brief Enable the remapping of TIM2 alternate function channels 1 to 4 and external trigger (ETR)
+  * @note  ENABLE: Full remap       (CH1/ETR/PA15, CH2/PB3, CH3/PB10, CH4/PB11)
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_TIM2_ENABLE()  AFIO_REMAP_PARTIAL(AFIO_MAPR_TIM2_REMAP_FULLREMAP, AFIO_MAPR_TIM2_REMAP_FULLREMAP)
+
+/**
+  * @brief Enable the remapping of TIM2 alternate function channels 1 to 4 and external trigger (ETR)
+  * @note  PARTIAL_2: Partial remap (CH1/ETR/PA0,  CH2/PA1, CH3/PB10, CH4/PB11)
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_TIM2_PARTIAL_2()  AFIO_REMAP_PARTIAL(AFIO_MAPR_TIM2_REMAP_PARTIALREMAP2, AFIO_MAPR_TIM2_REMAP_FULLREMAP)
+
+/**
+  * @brief Enable the remapping of TIM2 alternate function channels 1 to 4 and external trigger (ETR)
+  * @note  PARTIAL_1: Partial remap (CH1/ETR/PA15, CH2/PB3, CH3/PA2,  CH4/PA3)
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_TIM2_PARTIAL_1()  AFIO_REMAP_PARTIAL(AFIO_MAPR_TIM2_REMAP_PARTIALREMAP1, AFIO_MAPR_TIM2_REMAP_FULLREMAP)
+
+/**
+  * @brief Disable the remapping of TIM2 alternate function channels 1 to 4 and external trigger (ETR)
+  * @note  DISABLE: No remap        (CH1/ETR/PA0,  CH2/PA1, CH3/PA2,  CH4/PA3)
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_TIM2_DISABLE()  AFIO_REMAP_PARTIAL(AFIO_MAPR_TIM2_REMAP_NOREMAP, AFIO_MAPR_TIM2_REMAP_FULLREMAP)
+
+/**
+  * @brief Enable the remapping of TIM3 alternate function channels 1 to 4
+  * @note  ENABLE: Full remap     (CH1/PC6, CH2/PC7, CH3/PC8, CH4/PC9)
+  * @note  TIM3_ETR on PE0 is not re-mapped.
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_TIM3_ENABLE()  AFIO_REMAP_PARTIAL(AFIO_MAPR_TIM3_REMAP_FULLREMAP, AFIO_MAPR_TIM3_REMAP_FULLREMAP)
+
+/**
+  * @brief Enable the remapping of TIM3 alternate function channels 1 to 4
+  * @note  PARTIAL: Partial remap (CH1/PB4, CH2/PB5, CH3/PB0, CH4/PB1)
+  * @note  TIM3_ETR on PE0 is not re-mapped.
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_TIM3_PARTIAL()  AFIO_REMAP_PARTIAL(AFIO_MAPR_TIM3_REMAP_PARTIALREMAP, AFIO_MAPR_TIM3_REMAP_FULLREMAP)
+
+/**
+  * @brief Disable the remapping of TIM3 alternate function channels 1 to 4
+  * @note  DISABLE: No remap      (CH1/PA6, CH2/PA7, CH3/PB0, CH4/PB1)
+  * @note  TIM3_ETR on PE0 is not re-mapped.
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_TIM3_DISABLE()  AFIO_REMAP_PARTIAL(AFIO_MAPR_TIM3_REMAP_NOREMAP, AFIO_MAPR_TIM3_REMAP_FULLREMAP)
+
+/**
+  * @brief Enable the remapping of TIM4 alternate function channels 1 to 4.
+  * @note  ENABLE: Full remap (TIM4_CH1/PD12, TIM4_CH2/PD13, TIM4_CH3/PD14, TIM4_CH4/PD15)
+  * @note  TIM4_ETR on PE0 is not re-mapped.
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_TIM4_ENABLE()  AFIO_REMAP_ENABLE(AFIO_MAPR_TIM4_REMAP)
+
+/**
+  * @brief Disable the remapping of TIM4 alternate function channels 1 to 4.
+  * @note  DISABLE: No remap  (TIM4_CH1/PB6,  TIM4_CH2/PB7,  TIM4_CH3/PB8,  TIM4_CH4/PB9)
+  * @note  TIM4_ETR on PE0 is not re-mapped.
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_TIM4_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_TIM4_REMAP)
+
+#if defined(AFIO_MAPR_CAN_REMAP_REMAP1)
+
+/**
+  * @brief Enable or disable the remapping of CAN alternate function CAN_RX and CAN_TX in devices with a single CAN interface.
+  * @note  CASE 1: CAN_RX mapped to PA11, CAN_TX mapped to PA12
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_CAN1_1()  AFIO_REMAP_PARTIAL(AFIO_MAPR_CAN_REMAP_REMAP1, AFIO_MAPR_CAN_REMAP)
+
+/**
+  * @brief Enable or disable the remapping of CAN alternate function CAN_RX and CAN_TX in devices with a single CAN interface.
+  * @note  CASE 2: CAN_RX mapped to PB8,  CAN_TX mapped to PB9 (not available on 36-pin package)
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_CAN1_2()  AFIO_REMAP_PARTIAL(AFIO_MAPR_CAN_REMAP_REMAP2, AFIO_MAPR_CAN_REMAP)
+
+/**
+  * @brief Enable or disable the remapping of CAN alternate function CAN_RX and CAN_TX in devices with a single CAN interface.
+  * @note  CASE 3: CAN_RX mapped to PD0,  CAN_TX mapped to PD1
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_CAN1_3()  AFIO_REMAP_PARTIAL(AFIO_MAPR_CAN_REMAP_REMAP3, AFIO_MAPR_CAN_REMAP)
+
+#endif
+
+/**
+  * @brief Enable the remapping of PD0 and PD1. When the HSE oscillator is not used
+  *        (application running on internal 8 MHz RC) PD0 and PD1 can be mapped on OSC_IN and
+  *        OSC_OUT. This is available only on 36, 48 and 64 pins packages (PD0 and PD1 are available
+  *        on 100-pin and 144-pin packages, no need for remapping).
+  * @note  ENABLE: PD0 remapped on OSC_IN, PD1 remapped on OSC_OUT.
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_PD01_ENABLE()  AFIO_REMAP_ENABLE(AFIO_MAPR_PD01_REMAP)
+
+/**
+  * @brief Disable the remapping of PD0 and PD1. When the HSE oscillator is not used
+  *        (application running on internal 8 MHz RC) PD0 and PD1 can be mapped on OSC_IN and
+  *        OSC_OUT. This is available only on 36, 48 and 64 pins packages (PD0 and PD1 are available
+  *        on 100-pin and 144-pin packages, no need for remapping).
+  * @note  DISABLE: No remapping of PD0 and PD1
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_PD01_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_PD01_REMAP)
+
+#if defined(AFIO_MAPR_TIM5CH4_IREMAP)
+/**
+  * @brief Enable the remapping of TIM5CH4.
+  * @note  ENABLE: LSI internal clock is connected to TIM5_CH4 input for calibration purpose.
+  * @note  This function is available only in high density value line devices.
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_TIM5CH4_ENABLE()  AFIO_REMAP_ENABLE(AFIO_MAPR_TIM5CH4_IREMAP)
+
+/**
+  * @brief Disable the remapping of TIM5CH4.
+  * @note  DISABLE: TIM5_CH4 is connected to PA3
+  * @note  This function is available only in high density value line devices.
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_TIM5CH4_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_TIM5CH4_IREMAP)
+#endif
+
+#if defined(AFIO_MAPR_ETH_REMAP)
+/**
+  * @brief Enable the remapping of Ethernet MAC connections with the PHY.
+  * @note  ENABLE: Remap     (RX_DV-CRS_DV/PD8, RXD0/PD9, RXD1/PD10, RXD2/PD11, RXD3/PD12)
+  * @note  This bit is available only in connectivity line devices and is reserved otherwise.
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_ETH_ENABLE()  AFIO_REMAP_ENABLE(AFIO_MAPR_ETH_REMAP)
+
+/**
+  * @brief Disable the remapping of Ethernet MAC connections with the PHY.
+  * @note  DISABLE: No remap (RX_DV-CRS_DV/PA7, RXD0/PC4, RXD1/PC5,  RXD2/PB0,  RXD3/PB1)
+  * @note  This bit is available only in connectivity line devices and is reserved otherwise.
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_ETH_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_ETH_REMAP)
+#endif
+
+#if defined(AFIO_MAPR_CAN2_REMAP)
+
+/**
+  * @brief Enable the remapping of CAN2 alternate function CAN2_RX and CAN2_TX.
+  * @note  ENABLE: Remap     (CAN2_RX/PB5,  CAN2_TX/PB6)
+  * @note  This bit is available only in connectivity line devices and is reserved otherwise.
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_CAN2_ENABLE()  AFIO_REMAP_ENABLE(AFIO_MAPR_CAN2_REMAP)
+
+/**
+  * @brief Disable the remapping of CAN2 alternate function CAN2_RX and CAN2_TX.
+  * @note  DISABLE: No remap (CAN2_RX/PB12, CAN2_TX/PB13)
+  * @note  This bit is available only in connectivity line devices and is reserved otherwise.
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_CAN2_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_CAN2_REMAP)
+#endif
+
+#if defined(AFIO_MAPR_MII_RMII_SEL)
+/**
+  * @brief Configures the Ethernet MAC internally for use with an external MII or RMII PHY.
+  * @note  ETH_RMII: Configure Ethernet MAC for connection with an RMII PHY
+  * @note  This bit is available only in connectivity line devices and is reserved otherwise.
+  * @retval None
+  */
+#define __HAL_AFIO_ETH_RMII() AFIO_REMAP_ENABLE(AFIO_MAPR_MII_RMII_SEL)
+
+/**
+  * @brief Configures the Ethernet MAC internally for use with an external MII or RMII PHY.
+  * @note  ETH_MII: Configure Ethernet MAC for connection with an MII PHY
+  * @note  This bit is available only in connectivity line devices and is reserved otherwise.
+  * @retval None
+  */
+#define __HAL_AFIO_ETH_MII()  AFIO_REMAP_DISABLE(AFIO_MAPR_MII_RMII_SEL)
+#endif
+
+/**
+  * @brief Enable the remapping of ADC1_ETRGINJ (ADC 1 External trigger injected conversion).
+  * @note  ENABLE: ADC1 External Event injected conversion is connected to TIM8 Channel4.
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_ADC1_ETRGINJ_ENABLE()  AFIO_REMAP_ENABLE(AFIO_MAPR_ADC1_ETRGINJ_REMAP)
+
+/**
+  * @brief Disable the remapping of ADC1_ETRGINJ (ADC 1 External trigger injected conversion).
+  * @note  DISABLE: ADC1 External trigger injected conversion is connected to EXTI15
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_ADC1_ETRGINJ_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_ADC1_ETRGINJ_REMAP)
+
+/**
+  * @brief Enable the remapping of ADC1_ETRGREG (ADC 1 External trigger regular conversion).
+  * @note  ENABLE: ADC1 External Event regular conversion is connected to TIM8 TRG0.
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_ADC1_ETRGREG_ENABLE()  AFIO_REMAP_ENABLE(AFIO_MAPR_ADC1_ETRGREG_REMAP)
+
+/**
+  * @brief Disable the remapping of ADC1_ETRGREG (ADC 1 External trigger regular conversion).
+  * @note  DISABLE: ADC1 External trigger regular conversion is connected to EXTI11
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_ADC1_ETRGREG_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_ADC1_ETRGREG_REMAP)
+
+#if defined(AFIO_MAPR_ADC2_ETRGINJ_REMAP)
+
+/**
+  * @brief Enable the remapping of ADC2_ETRGREG (ADC 2 External trigger injected conversion).
+  * @note  ENABLE: ADC2 External Event injected conversion is connected to TIM8 Channel4.
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_ADC2_ETRGINJ_ENABLE()  AFIO_REMAP_ENABLE(AFIO_MAPR_ADC2_ETRGINJ_REMAP)
+
+/**
+  * @brief Disable the remapping of ADC2_ETRGREG (ADC 2 External trigger injected conversion).
+  * @note  DISABLE: ADC2 External trigger injected conversion is connected to EXTI15
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_ADC2_ETRGINJ_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_ADC2_ETRGINJ_REMAP)
+#endif
+
+#if defined (AFIO_MAPR_ADC2_ETRGREG_REMAP)
+
+/**
+  * @brief Enable the remapping of ADC2_ETRGREG (ADC 2 External trigger regular conversion).
+  * @note  ENABLE: ADC2 External Event regular conversion is connected to TIM8 TRG0.
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_ADC2_ETRGREG_ENABLE()  AFIO_REMAP_ENABLE(AFIO_MAPR_ADC2_ETRGREG_REMAP)
+
+/**
+  * @brief Disable the remapping of ADC2_ETRGREG (ADC 2 External trigger regular conversion).
+  * @note  DISABLE: ADC2 External trigger regular conversion is connected to EXTI11
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_ADC2_ETRGREG_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_ADC2_ETRGREG_REMAP)
+#endif
+
+/**
+  * @brief Enable the Serial wire JTAG configuration
+  * @note  ENABLE: Full SWJ (JTAG-DP + SW-DP): Reset State
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_SWJ_ENABLE()  AFIO_DBGAFR_CONFIG(AFIO_MAPR_SWJ_CFG_RESET)
+
+/**
+  * @brief Enable the Serial wire JTAG configuration
+  * @note  NONJTRST: Full SWJ (JTAG-DP + SW-DP) but without NJTRST
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_SWJ_NONJTRST()  AFIO_DBGAFR_CONFIG(AFIO_MAPR_SWJ_CFG_NOJNTRST)
+
+/**
+  * @brief Enable the Serial wire JTAG configuration
+  * @note  NOJTAG: JTAG-DP Disabled and SW-DP Enabled
+  * @retval None
+  */
+
+#define __HAL_AFIO_REMAP_SWJ_NOJTAG()  AFIO_DBGAFR_CONFIG(AFIO_MAPR_SWJ_CFG_JTAGDISABLE)
+
+/**
+  * @brief Disable the Serial wire JTAG configuration
+  * @note  DISABLE: JTAG-DP Disabled and SW-DP Disabled
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_SWJ_DISABLE()  AFIO_DBGAFR_CONFIG(AFIO_MAPR_SWJ_CFG_DISABLE)
+
+#if defined(AFIO_MAPR_SPI3_REMAP)
+
+/**
+  * @brief Enable the remapping of SPI3 alternate functions SPI3_NSS/I2S3_WS, SPI3_SCK/I2S3_CK, SPI3_MISO, SPI3_MOSI/I2S3_SD.
+  * @note  ENABLE: Remap     (SPI3_NSS-I2S3_WS/PA4,  SPI3_SCK-I2S3_CK/PC10, SPI3_MISO/PC11, SPI3_MOSI-I2S3_SD/PC12)
+  * @note  This bit is available only in connectivity line devices and is reserved otherwise.
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_SPI3_ENABLE()  AFIO_REMAP_ENABLE(AFIO_MAPR_SPI3_REMAP)
+
+/**
+  * @brief Disable the remapping of SPI3 alternate functions SPI3_NSS/I2S3_WS, SPI3_SCK/I2S3_CK, SPI3_MISO, SPI3_MOSI/I2S3_SD.
+  * @note  DISABLE: No remap (SPI3_NSS-I2S3_WS/PA15, SPI3_SCK-I2S3_CK/PB3,  SPI3_MISO/PB4,  SPI3_MOSI-I2S3_SD/PB5).
+  * @note  This bit is available only in connectivity line devices and is reserved otherwise.
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_SPI3_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_SPI3_REMAP)
+#endif
+
+#if defined(AFIO_MAPR_TIM2ITR1_IREMAP)
+
+/**
+  * @brief Control of TIM2_ITR1 internal mapping.
+  * @note  TO_USB: Connect USB OTG SOF (Start of Frame) output to TIM2_ITR1 for calibration purposes.
+  * @note  This bit is available only in connectivity line devices and is reserved otherwise.
+  * @retval None
+  */
+#define __HAL_AFIO_TIM2ITR1_TO_USB() AFIO_REMAP_ENABLE(AFIO_MAPR_TIM2ITR1_IREMAP)
+
+/**
+  * @brief Control of TIM2_ITR1 internal mapping.
+  * @note  TO_ETH: Connect TIM2_ITR1 internally to the Ethernet PTP output for calibration purposes.
+  * @note  This bit is available only in connectivity line devices and is reserved otherwise.
+  * @retval None
+  */
+#define __HAL_AFIO_TIM2ITR1_TO_ETH() AFIO_REMAP_DISABLE(AFIO_MAPR_TIM2ITR1_IREMAP)
+#endif
+
+#if defined(AFIO_MAPR_PTP_PPS_REMAP)
+
+/**
+  * @brief Enable the remapping of ADC2_ETRGREG (ADC 2 External trigger regular conversion).
+  * @note  ENABLE: PTP_PPS is output on PB5 pin.
+  * @note  This bit is available only in connectivity line devices and is reserved otherwise.
+  * @retval None
+  */
+#define __HAL_AFIO_ETH_PTP_PPS_ENABLE()  AFIO_REMAP_ENABLE(AFIO_MAPR_PTP_PPS_REMAP)
+
+/**
+  * @brief Disable the remapping of ADC2_ETRGREG (ADC 2 External trigger regular conversion).
+  * @note  DISABLE: PTP_PPS not output on PB5 pin.
+  * @note  This bit is available only in connectivity line devices and is reserved otherwise.
+  * @retval None
+  */
+#define __HAL_AFIO_ETH_PTP_PPS_DISABLE() AFIO_REMAP_DISABLE(AFIO_MAPR_PTP_PPS_REMAP)
+#endif
+
+#if defined(AFIO_MAPR2_TIM9_REMAP)
+
+/**
+  * @brief Enable the remapping of TIM9_CH1 and TIM9_CH2.
+  * @note  ENABLE: Remap     (TIM9_CH1 on PE5 and TIM9_CH2 on PE6).
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_TIM9_ENABLE()  SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM9_REMAP)
+
+/**
+  * @brief Disable the remapping of TIM9_CH1 and TIM9_CH2.
+  * @note  DISABLE: No remap (TIM9_CH1 on PA2 and TIM9_CH2 on PA3).
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_TIM9_DISABLE() CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM9_REMAP)
+#endif
+
+#if defined(AFIO_MAPR2_TIM10_REMAP)
+
+/**
+  * @brief Enable the remapping of TIM10_CH1.
+  * @note  ENABLE: Remap     (TIM10_CH1 on PF6).
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_TIM10_ENABLE()  SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM10_REMAP)
+
+/**
+  * @brief Disable the remapping of TIM10_CH1.
+  * @note  DISABLE: No remap (TIM10_CH1 on PB8).
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_TIM10_DISABLE() CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM10_REMAP)
+#endif
+
+#if defined(AFIO_MAPR2_TIM11_REMAP)
+/**
+  * @brief Enable the remapping of TIM11_CH1.
+  * @note  ENABLE: Remap     (TIM11_CH1 on PF7).
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_TIM11_ENABLE()  SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM11_REMAP)
+
+/**
+  * @brief Disable the remapping of TIM11_CH1.
+  * @note  DISABLE: No remap (TIM11_CH1 on PB9).
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_TIM11_DISABLE() CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM11_REMAP)
+#endif
+
+#if defined(AFIO_MAPR2_TIM13_REMAP)
+
+/**
+  * @brief Enable the remapping of TIM13_CH1.
+  * @note  ENABLE: Remap     STM32F100:(TIM13_CH1 on PF8). Others:(TIM13_CH1 on PB0).
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_TIM13_ENABLE()  SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM13_REMAP)
+
+/**
+  * @brief Disable the remapping of TIM13_CH1.
+  * @note  DISABLE: No remap STM32F100:(TIM13_CH1 on PA6). Others:(TIM13_CH1 on PC8).
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_TIM13_DISABLE() CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM13_REMAP)
+#endif
+
+#if defined(AFIO_MAPR2_TIM14_REMAP)
+
+/**
+  * @brief Enable the remapping of TIM14_CH1.
+  * @note  ENABLE: Remap     STM32F100:(TIM14_CH1 on PB1). Others:(TIM14_CH1 on PF9).
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_TIM14_ENABLE()  SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM14_REMAP)
+
+/**
+  * @brief Disable the remapping of TIM14_CH1.
+  * @note  DISABLE: No remap STM32F100:(TIM14_CH1 on PC9). Others:(TIM14_CH1 on PA7).
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_TIM14_DISABLE() CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM14_REMAP)
+#endif
+
+#if defined(AFIO_MAPR2_FSMC_NADV_REMAP)
+
+/**
+  * @brief Controls the use of the optional FSMC_NADV signal.
+  * @note  DISCONNECTED: The NADV signal is not connected. The I/O pin can be used by another peripheral.
+  * @retval None
+  */
+#define __HAL_AFIO_FSMCNADV_DISCONNECTED() SET_BIT(AFIO->MAPR2, AFIO_MAPR2_FSMC_NADV_REMAP)
+
+/**
+  * @brief Controls the use of the optional FSMC_NADV signal.
+  * @note  CONNECTED: The NADV signal is connected to the output (default).
+  * @retval None
+  */
+#define __HAL_AFIO_FSMCNADV_CONNECTED()    CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_FSMC_NADV_REMAP)
+#endif
+
+#if defined(AFIO_MAPR2_TIM15_REMAP)
+
+/**
+  * @brief Enable the remapping of TIM15_CH1 and TIM15_CH2.
+  * @note  ENABLE: Remap     (TIM15_CH1 on PB14 and TIM15_CH2 on PB15).
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_TIM15_ENABLE()  SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM15_REMAP)
+
+/**
+  * @brief Disable the remapping of TIM15_CH1 and TIM15_CH2.
+  * @note  DISABLE: No remap (TIM15_CH1 on PA2  and TIM15_CH2 on PA3).
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_TIM15_DISABLE() CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM15_REMAP)
+#endif
+
+#if defined(AFIO_MAPR2_TIM16_REMAP)
+
+/**
+  * @brief Enable the remapping of TIM16_CH1.
+  * @note  ENABLE: Remap     (TIM16_CH1 on PA6).
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_TIM16_ENABLE()  SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM16_REMAP)
+
+/**
+  * @brief Disable the remapping of TIM16_CH1.
+  * @note  DISABLE: No remap (TIM16_CH1 on PB8).
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_TIM16_DISABLE() CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM16_REMAP)
+#endif
+
+#if defined(AFIO_MAPR2_TIM17_REMAP)
+
+/**
+  * @brief Enable the remapping of TIM17_CH1.
+  * @note  ENABLE: Remap     (TIM17_CH1 on PA7).
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_TIM17_ENABLE()  SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM17_REMAP)
+
+/**
+  * @brief Disable the remapping of TIM17_CH1.
+  * @note  DISABLE: No remap (TIM17_CH1 on PB9).
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_TIM17_DISABLE() CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM17_REMAP)
+#endif
+
+#if defined(AFIO_MAPR2_CEC_REMAP)
+
+/**
+  * @brief Enable the remapping of CEC.
+  * @note  ENABLE: Remap     (CEC on PB10).
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_CEC_ENABLE()  SET_BIT(AFIO->MAPR2, AFIO_MAPR2_CEC_REMAP)
+
+/**
+  * @brief Disable the remapping of CEC.
+  * @note  DISABLE: No remap (CEC on PB8).
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_CEC_DISABLE() CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_CEC_REMAP)
+#endif
+
+#if defined(AFIO_MAPR2_TIM1_DMA_REMAP)
+
+/**
+  * @brief Controls the mapping of the TIM1_CH1 TIM1_CH2 DMA requests onto the DMA1 channels.
+  * @note  ENABLE: Remap (TIM1_CH1 DMA request/DMA1 Channel6, TIM1_CH2 DMA request/DMA1 Channel6)
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_TIM1DMA_ENABLE()  SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM1_DMA_REMAP)
+
+/**
+  * @brief Controls the mapping of the TIM1_CH1 TIM1_CH2 DMA requests onto the DMA1 channels.
+  * @note  DISABLE: No remap (TIM1_CH1 DMA request/DMA1 Channel2, TIM1_CH2 DMA request/DMA1 Channel3).
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_TIM1DMA_DISABLE() CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM1_DMA_REMAP)
+#endif
+
+#if defined(AFIO_MAPR2_TIM67_DAC_DMA_REMAP)
+
+/**
+  * @brief Controls the mapping of the TIM6_DAC1 and TIM7_DAC2 DMA requests onto the DMA1 channels.
+  * @note  ENABLE: Remap (TIM6_DAC1 DMA request/DMA1 Channel3, TIM7_DAC2 DMA request/DMA1 Channel4)
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_TIM67DACDMA_ENABLE()  SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM67_DAC_DMA_REMAP)
+
+/**
+  * @brief Controls the mapping of the TIM6_DAC1 and TIM7_DAC2 DMA requests onto the DMA1 channels.
+  * @note  DISABLE: No remap (TIM6_DAC1 DMA request/DMA2 Channel3, TIM7_DAC2 DMA request/DMA2 Channel4)
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_TIM67DACDMA_DISABLE() CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM67_DAC_DMA_REMAP)
+#endif
+
+#if defined(AFIO_MAPR2_TIM12_REMAP)
+
+/**
+  * @brief Enable the remapping of TIM12_CH1 and TIM12_CH2.
+  * @note  ENABLE: Remap     (TIM12_CH1 on PB12 and TIM12_CH2 on PB13).
+  * @note  This bit is available only in high density value line devices.
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_TIM12_ENABLE()  SET_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM12_REMAP)
+
+/**
+  * @brief Disable the remapping of TIM12_CH1 and TIM12_CH2.
+  * @note  DISABLE: No remap (TIM12_CH1 on PC4  and TIM12_CH2 on PC5).
+  * @note  This bit is available only in high density value line devices.
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_TIM12_DISABLE() CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_TIM12_REMAP)
+#endif
+
+#if defined(AFIO_MAPR2_MISC_REMAP)
+
+/**
+  * @brief Miscellaneous features remapping.
+  *        This bit is set and cleared by software. It controls miscellaneous features.
+  *        The DMA2 channel 5 interrupt position in the vector table.
+  *        The timer selection for DAC trigger 3 (TSEL[2:0] = 011, for more details refer to the DAC_CR register).
+  * @note  ENABLE: DMA2 channel 5 interrupt is mapped separately at position 60 and TIM15 TRGO event is
+  *        selected as DAC Trigger 3, TIM15 triggers TIM1/3.
+  * @note  This bit is available only in high density value line devices.
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_MISC_ENABLE()  SET_BIT(AFIO->MAPR2, AFIO_MAPR2_MISC_REMAP)
+
+/**
+  * @brief Miscellaneous features remapping.
+  *        This bit is set and cleared by software. It controls miscellaneous features.
+  *        The DMA2 channel 5 interrupt position in the vector table.
+  *        The timer selection for DAC trigger 3 (TSEL[2:0] = 011, for more details refer to the DAC_CR register).
+  * @note  DISABLE: DMA2 channel 5 interrupt is mapped with DMA2 channel 4 at position 59, TIM5 TRGO
+  *        event is selected as DAC Trigger 3, TIM5 triggers TIM1/3.
+  * @note  This bit is available only in high density value line devices.
+  * @retval None
+  */
+#define __HAL_AFIO_REMAP_MISC_DISABLE() CLEAR_BIT(AFIO->MAPR2, AFIO_MAPR2_MISC_REMAP)
+#endif
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/** @defgroup GPIOEx_Private_Macros GPIOEx Private Macros
+  * @{
+  */
+#if defined(STM32F101x6) || defined(STM32F102x6) || defined(STM32F102xB) || defined(STM32F103x6)
+#define GPIO_GET_INDEX(__GPIOx__) (((__GPIOx__) == (GPIOA))? 0uL :\
+                                   ((__GPIOx__) == (GPIOB))? 1uL :\
+                                   ((__GPIOx__) == (GPIOC))? 2uL :3uL)
+#elif defined(STM32F100xB) || defined(STM32F101xB) || defined(STM32F103xB) || defined(STM32F105xC) || defined(STM32F107xC)
+#define GPIO_GET_INDEX(__GPIOx__) (((__GPIOx__) == (GPIOA))? 0uL :\
+                                   ((__GPIOx__) == (GPIOB))? 1uL :\
+                                   ((__GPIOx__) == (GPIOC))? 2uL :\
+                                   ((__GPIOx__) == (GPIOD))? 3uL :4uL)
+#elif defined(STM32F100xE) || defined(STM32F101xE) || defined(STM32F101xG) || defined(STM32F103xE) || defined(STM32F103xG)
+#define GPIO_GET_INDEX(__GPIOx__) (((__GPIOx__) == (GPIOA))? 0uL :\
+                                   ((__GPIOx__) == (GPIOB))? 1uL :\
+                                   ((__GPIOx__) == (GPIOC))? 2uL :\
+                                   ((__GPIOx__) == (GPIOD))? 3uL :\
+                                   ((__GPIOx__) == (GPIOE))? 4uL :\
+                                   ((__GPIOx__) == (GPIOF))? 5uL :6uL)
+#endif
+
+#define AFIO_REMAP_ENABLE(REMAP_PIN)       do{ uint32_t tmpreg = AFIO->MAPR; \
+                                               tmpreg |= AFIO_MAPR_SWJ_CFG;  \
+                                               tmpreg |= REMAP_PIN;          \
+                                               AFIO->MAPR = tmpreg;          \
+                                               }while(0u)
+
+#define AFIO_REMAP_DISABLE(REMAP_PIN)      do{ uint32_t tmpreg = AFIO->MAPR;  \
+                                               tmpreg |= AFIO_MAPR_SWJ_CFG;   \
+                                               tmpreg &= ~REMAP_PIN;          \
+                                               AFIO->MAPR = tmpreg;           \
+                                               }while(0u)
+
+#define AFIO_REMAP_PARTIAL(REMAP_PIN, REMAP_PIN_MASK) do{ uint32_t tmpreg = AFIO->MAPR; \
+                                                          tmpreg &= ~REMAP_PIN_MASK;    \
+                                                          tmpreg |= AFIO_MAPR_SWJ_CFG;  \
+                                                          tmpreg |= REMAP_PIN;          \
+                                                          AFIO->MAPR = tmpreg;          \
+                                                          }while(0u)
+
+#define AFIO_DBGAFR_CONFIG(DBGAFR_SWJCFG)  do{ uint32_t tmpreg = AFIO->MAPR;     \
+                                               tmpreg &= ~AFIO_MAPR_SWJ_CFG_Msk; \
+                                               tmpreg |= DBGAFR_SWJCFG;          \
+                                               AFIO->MAPR = tmpreg;              \
+                                               }while(0u)
+
+/**
+  * @}
+  */
+
+/* Exported macro ------------------------------------------------------------*/
+/* Exported functions --------------------------------------------------------*/
+
+/** @addtogroup GPIOEx_Exported_Functions
+  * @{
+  */
+
+/** @addtogroup GPIOEx_Exported_Functions_Group1
+  * @{
+  */
+void HAL_GPIOEx_ConfigEventout(uint32_t GPIO_PortSource, uint32_t GPIO_PinSource);
+void HAL_GPIOEx_EnableEventout(void);
+void HAL_GPIOEx_DisableEventout(void);
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* STM32F1xx_HAL_GPIO_EX_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_hcd.h

@@ -0,0 +1,318 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_hal_hcd.h
+  * @author  MCD Application Team
+  * @brief   Header file of HCD HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef STM32F1xx_HAL_HCD_H
+#define STM32F1xx_HAL_HCD_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_ll_usb.h"
+
+#if defined (USB_OTG_FS)
+/** @addtogroup STM32F1xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup HCD HCD
+  * @{
+  */
+
+/* Exported types ------------------------------------------------------------*/
+/** @defgroup HCD_Exported_Types HCD Exported Types
+  * @{
+  */
+
+/** @defgroup HCD_Exported_Types_Group1 HCD State Structure definition
+  * @{
+  */
+typedef enum
+{
+  HAL_HCD_STATE_RESET    = 0x00,
+  HAL_HCD_STATE_READY    = 0x01,
+  HAL_HCD_STATE_ERROR    = 0x02,
+  HAL_HCD_STATE_BUSY     = 0x03,
+  HAL_HCD_STATE_TIMEOUT  = 0x04
+} HCD_StateTypeDef;
+
+typedef USB_OTG_GlobalTypeDef   HCD_TypeDef;
+typedef USB_OTG_CfgTypeDef      HCD_InitTypeDef;
+typedef USB_OTG_HCTypeDef       HCD_HCTypeDef;
+typedef USB_OTG_URBStateTypeDef HCD_URBStateTypeDef;
+typedef USB_OTG_HCStateTypeDef  HCD_HCStateTypeDef;
+/**
+  * @}
+  */
+
+/** @defgroup HCD_Exported_Types_Group2 HCD Handle Structure definition
+  * @{
+  */
+#if (USE_HAL_HCD_REGISTER_CALLBACKS == 1U)
+typedef struct __HCD_HandleTypeDef
+#else
+typedef struct
+#endif /* USE_HAL_HCD_REGISTER_CALLBACKS */
+{
+  HCD_TypeDef               *Instance;  /*!< Register base address    */
+  HCD_InitTypeDef           Init;       /*!< HCD required parameters  */
+  HCD_HCTypeDef             hc[16];     /*!< Host channels parameters */
+  HAL_LockTypeDef           Lock;       /*!< HCD peripheral status    */
+  __IO HCD_StateTypeDef     State;      /*!< HCD communication state  */
+  __IO  uint32_t            ErrorCode;  /*!< HCD Error code           */
+  void                      *pData;     /*!< Pointer Stack Handler    */
+#if (USE_HAL_HCD_REGISTER_CALLBACKS == 1U)
+  void (* SOFCallback)(struct __HCD_HandleTypeDef *hhcd);                               /*!< USB OTG HCD SOF callback                */
+  void (* ConnectCallback)(struct __HCD_HandleTypeDef *hhcd);                           /*!< USB OTG HCD Connect callback            */
+  void (* DisconnectCallback)(struct __HCD_HandleTypeDef *hhcd);                        /*!< USB OTG HCD Disconnect callback         */
+  void (* PortEnabledCallback)(struct __HCD_HandleTypeDef *hhcd);                       /*!< USB OTG HCD Port Enable callback        */
+  void (* PortDisabledCallback)(struct __HCD_HandleTypeDef *hhcd);                      /*!< USB OTG HCD Port Disable callback       */
+  void (* HC_NotifyURBChangeCallback)(struct __HCD_HandleTypeDef *hhcd, uint8_t chnum,
+                                      HCD_URBStateTypeDef urb_state);                   /*!< USB OTG HCD Host Channel Notify URB Change callback  */
+
+  void (* MspInitCallback)(struct __HCD_HandleTypeDef *hhcd);                           /*!< USB OTG HCD Msp Init callback           */
+  void (* MspDeInitCallback)(struct __HCD_HandleTypeDef *hhcd);                         /*!< USB OTG HCD Msp DeInit callback         */
+#endif /* USE_HAL_HCD_REGISTER_CALLBACKS */
+} HCD_HandleTypeDef;
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup HCD_Exported_Constants HCD Exported Constants
+  * @{
+  */
+
+/** @defgroup HCD_Speed HCD Speed
+  * @{
+  */
+#define HCD_SPEED_FULL               USBH_FSLS_SPEED
+#define HCD_SPEED_LOW                USBH_FSLS_SPEED
+/**
+  * @}
+  */
+
+/** @defgroup HCD_Device_Speed HCD Device Speed
+  * @{
+  */
+#define HCD_DEVICE_SPEED_HIGH               0U
+#define HCD_DEVICE_SPEED_FULL               1U
+#define HCD_DEVICE_SPEED_LOW                2U
+/**
+  * @}
+  */
+
+/** @defgroup HCD_PHY_Module HCD PHY Module
+  * @{
+  */
+#define HCD_PHY_ULPI                 1U
+#define HCD_PHY_EMBEDDED             2U
+/**
+  * @}
+  */
+
+/** @defgroup HCD_Error_Code_definition HCD Error Code definition
+  * @brief  HCD Error Code definition
+  * @{
+  */
+#if (USE_HAL_HCD_REGISTER_CALLBACKS == 1U)
+#define  HAL_HCD_ERROR_INVALID_CALLBACK                        (0x00000010U)    /*!< Invalid Callback error  */
+#endif /* USE_HAL_HCD_REGISTER_CALLBACKS */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Exported macro ------------------------------------------------------------*/
+/** @defgroup HCD_Exported_Macros HCD Exported Macros
+  *  @brief macros to handle interrupts and specific clock configurations
+  * @{
+  */
+#define __HAL_HCD_ENABLE(__HANDLE__)                   (void)USB_EnableGlobalInt ((__HANDLE__)->Instance)
+#define __HAL_HCD_DISABLE(__HANDLE__)                  (void)USB_DisableGlobalInt ((__HANDLE__)->Instance)
+
+#define __HAL_HCD_GET_FLAG(__HANDLE__, __INTERRUPT__)      ((USB_ReadInterrupts((__HANDLE__)->Instance)\
+                                                             & (__INTERRUPT__)) == (__INTERRUPT__))
+#define __HAL_HCD_CLEAR_FLAG(__HANDLE__, __INTERRUPT__)    (((__HANDLE__)->Instance->GINTSTS) = (__INTERRUPT__))
+#define __HAL_HCD_IS_INVALID_INTERRUPT(__HANDLE__)         (USB_ReadInterrupts((__HANDLE__)->Instance) == 0U)
+
+#define __HAL_HCD_CLEAR_HC_INT(chnum, __INTERRUPT__)  (USBx_HC(chnum)->HCINT = (__INTERRUPT__))
+#define __HAL_HCD_MASK_HALT_HC_INT(chnum)             (USBx_HC(chnum)->HCINTMSK &= ~USB_OTG_HCINTMSK_CHHM)
+#define __HAL_HCD_UNMASK_HALT_HC_INT(chnum)           (USBx_HC(chnum)->HCINTMSK |= USB_OTG_HCINTMSK_CHHM)
+#define __HAL_HCD_MASK_ACK_HC_INT(chnum)              (USBx_HC(chnum)->HCINTMSK &= ~USB_OTG_HCINTMSK_ACKM)
+#define __HAL_HCD_UNMASK_ACK_HC_INT(chnum)            (USBx_HC(chnum)->HCINTMSK |= USB_OTG_HCINTMSK_ACKM)
+/**
+  * @}
+  */
+
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup HCD_Exported_Functions HCD Exported Functions
+  * @{
+  */
+
+/** @defgroup HCD_Exported_Functions_Group1 Initialization and de-initialization functions
+  * @{
+  */
+HAL_StatusTypeDef HAL_HCD_Init(HCD_HandleTypeDef *hhcd);
+HAL_StatusTypeDef HAL_HCD_DeInit(HCD_HandleTypeDef *hhcd);
+HAL_StatusTypeDef HAL_HCD_HC_Init(HCD_HandleTypeDef *hhcd, uint8_t ch_num,
+                                  uint8_t epnum, uint8_t dev_address,
+                                  uint8_t speed, uint8_t ep_type, uint16_t mps);
+
+HAL_StatusTypeDef HAL_HCD_HC_Halt(HCD_HandleTypeDef *hhcd, uint8_t ch_num);
+void              HAL_HCD_MspInit(HCD_HandleTypeDef *hhcd);
+void              HAL_HCD_MspDeInit(HCD_HandleTypeDef *hhcd);
+
+#if (USE_HAL_HCD_REGISTER_CALLBACKS == 1U)
+/** @defgroup HAL_HCD_Callback_ID_enumeration_definition HAL USB OTG HCD Callback ID enumeration definition
+  * @brief  HAL USB OTG HCD Callback ID enumeration definition
+  * @{
+  */
+typedef enum
+{
+  HAL_HCD_SOF_CB_ID            = 0x01,       /*!< USB HCD SOF callback ID           */
+  HAL_HCD_CONNECT_CB_ID        = 0x02,       /*!< USB HCD Connect callback ID       */
+  HAL_HCD_DISCONNECT_CB_ID     = 0x03,       /*!< USB HCD Disconnect callback ID    */
+  HAL_HCD_PORT_ENABLED_CB_ID   = 0x04,       /*!< USB HCD Port Enable callback ID   */
+  HAL_HCD_PORT_DISABLED_CB_ID  = 0x05,       /*!< USB HCD Port Disable callback ID  */
+
+  HAL_HCD_MSPINIT_CB_ID        = 0x06,       /*!< USB HCD MspInit callback ID       */
+  HAL_HCD_MSPDEINIT_CB_ID      = 0x07        /*!< USB HCD MspDeInit callback ID     */
+
+} HAL_HCD_CallbackIDTypeDef;
+/**
+  * @}
+  */
+
+/** @defgroup HAL_HCD_Callback_pointer_definition HAL USB OTG HCD Callback pointer definition
+  * @brief  HAL USB OTG HCD Callback pointer definition
+  * @{
+  */
+
+typedef void (*pHCD_CallbackTypeDef)(HCD_HandleTypeDef *hhcd);                   /*!< pointer to a common USB OTG HCD callback function  */
+typedef void (*pHCD_HC_NotifyURBChangeCallbackTypeDef)(HCD_HandleTypeDef *hhcd,
+                                                       uint8_t epnum,
+                                                       HCD_URBStateTypeDef urb_state);   /*!< pointer to USB OTG HCD host channel  callback */
+/**
+  * @}
+  */
+
+HAL_StatusTypeDef HAL_HCD_RegisterCallback(HCD_HandleTypeDef *hhcd,
+                                           HAL_HCD_CallbackIDTypeDef CallbackID,
+                                           pHCD_CallbackTypeDef pCallback);
+
+HAL_StatusTypeDef HAL_HCD_UnRegisterCallback(HCD_HandleTypeDef *hhcd,
+                                             HAL_HCD_CallbackIDTypeDef CallbackID);
+
+HAL_StatusTypeDef HAL_HCD_RegisterHC_NotifyURBChangeCallback(HCD_HandleTypeDef *hhcd,
+                                                             pHCD_HC_NotifyURBChangeCallbackTypeDef pCallback);
+
+HAL_StatusTypeDef HAL_HCD_UnRegisterHC_NotifyURBChangeCallback(HCD_HandleTypeDef *hhcd);
+#endif /* USE_HAL_HCD_REGISTER_CALLBACKS */
+/**
+  * @}
+  */
+
+/* I/O operation functions  ***************************************************/
+/** @addtogroup HCD_Exported_Functions_Group2 Input and Output operation functions
+  * @{
+  */
+HAL_StatusTypeDef HAL_HCD_HC_SubmitRequest(HCD_HandleTypeDef *hhcd, uint8_t ch_num,
+                                           uint8_t direction, uint8_t ep_type,
+                                           uint8_t token, uint8_t *pbuff,
+                                           uint16_t length, uint8_t do_ping);
+
+/* Non-Blocking mode: Interrupt */
+void HAL_HCD_IRQHandler(HCD_HandleTypeDef *hhcd);
+void HAL_HCD_WKUP_IRQHandler(HCD_HandleTypeDef *hhcd);
+void HAL_HCD_SOF_Callback(HCD_HandleTypeDef *hhcd);
+void HAL_HCD_Connect_Callback(HCD_HandleTypeDef *hhcd);
+void HAL_HCD_Disconnect_Callback(HCD_HandleTypeDef *hhcd);
+void HAL_HCD_PortEnabled_Callback(HCD_HandleTypeDef *hhcd);
+void HAL_HCD_PortDisabled_Callback(HCD_HandleTypeDef *hhcd);
+void HAL_HCD_HC_NotifyURBChange_Callback(HCD_HandleTypeDef *hhcd, uint8_t chnum,
+                                         HCD_URBStateTypeDef urb_state);
+/**
+  * @}
+  */
+
+/* Peripheral Control functions  **********************************************/
+/** @addtogroup HCD_Exported_Functions_Group3 Peripheral Control functions
+  * @{
+  */
+HAL_StatusTypeDef HAL_HCD_ResetPort(HCD_HandleTypeDef *hhcd);
+HAL_StatusTypeDef HAL_HCD_Start(HCD_HandleTypeDef *hhcd);
+HAL_StatusTypeDef HAL_HCD_Stop(HCD_HandleTypeDef *hhcd);
+/**
+  * @}
+  */
+
+/* Peripheral State functions  ************************************************/
+/** @addtogroup HCD_Exported_Functions_Group4 Peripheral State functions
+  * @{
+  */
+HCD_StateTypeDef        HAL_HCD_GetState(HCD_HandleTypeDef *hhcd);
+HCD_URBStateTypeDef     HAL_HCD_HC_GetURBState(HCD_HandleTypeDef *hhcd, uint8_t chnum);
+HCD_HCStateTypeDef      HAL_HCD_HC_GetState(HCD_HandleTypeDef *hhcd, uint8_t chnum);
+uint32_t                HAL_HCD_HC_GetXferCount(HCD_HandleTypeDef *hhcd, uint8_t chnum);
+uint32_t                HAL_HCD_GetCurrentFrame(HCD_HandleTypeDef *hhcd);
+uint32_t                HAL_HCD_GetCurrentSpeed(HCD_HandleTypeDef *hhcd);
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Private macros ------------------------------------------------------------*/
+/** @defgroup HCD_Private_Macros HCD Private Macros
+  * @{
+  */
+/**
+  * @}
+  */
+/* Private functions prototypes ----------------------------------------------*/
+
+/**
+  * @}
+  */
+/**
+  * @}
+  */
+#endif /* defined (USB_OTG_FS) */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* STM32F1xx_HAL_HCD_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_i2c.h

@@ -0,0 +1,740 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_hal_i2c.h
+  * @author  MCD Application Team
+  * @brief   Header file of I2C HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F1xx_HAL_I2C_H
+#define __STM32F1xx_HAL_I2C_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_hal_def.h"
+
+/** @addtogroup STM32F1xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup I2C
+  * @{
+  */
+
+/* Exported types ------------------------------------------------------------*/
+/** @defgroup I2C_Exported_Types I2C Exported Types
+  * @{
+  */
+
+/** @defgroup I2C_Configuration_Structure_definition I2C Configuration Structure definition
+  * @brief  I2C Configuration Structure definition
+  * @{
+  */
+typedef struct
+{
+  uint32_t ClockSpeed;       /*!< Specifies the clock frequency.
+                                  This parameter must be set to a value lower than 400kHz */
+
+  uint32_t DutyCycle;        /*!< Specifies the I2C fast mode duty cycle.
+                                  This parameter can be a value of @ref I2C_duty_cycle_in_fast_mode */
+
+  uint32_t OwnAddress1;      /*!< Specifies the first device own address.
+                                  This parameter can be a 7-bit or 10-bit address. */
+
+  uint32_t AddressingMode;   /*!< Specifies if 7-bit or 10-bit addressing mode is selected.
+                                  This parameter can be a value of @ref I2C_addressing_mode */
+
+  uint32_t DualAddressMode;  /*!< Specifies if dual addressing mode is selected.
+                                  This parameter can be a value of @ref I2C_dual_addressing_mode */
+
+  uint32_t OwnAddress2;      /*!< Specifies the second device own address if dual addressing mode is selected
+                                  This parameter can be a 7-bit address. */
+
+  uint32_t GeneralCallMode;  /*!< Specifies if general call mode is selected.
+                                  This parameter can be a value of @ref I2C_general_call_addressing_mode */
+
+  uint32_t NoStretchMode;    /*!< Specifies if nostretch mode is selected.
+                                  This parameter can be a value of @ref I2C_nostretch_mode */
+
+} I2C_InitTypeDef;
+
+/**
+  * @}
+  */
+
+/** @defgroup HAL_state_structure_definition HAL state structure definition
+  * @brief  HAL State structure definition
+  * @note  HAL I2C State value coding follow below described bitmap :
+  *          b7-b6  Error information
+  *             00 : No Error
+  *             01 : Abort (Abort user request on going)
+  *             10 : Timeout
+  *             11 : Error
+  *          b5     Peripheral initialization status
+  *             0  : Reset (Peripheral not initialized)
+  *             1  : Init done (Peripheral initialized and ready to use. HAL I2C Init function called)
+  *          b4     (not used)
+  *             x  : Should be set to 0
+  *          b3
+  *             0  : Ready or Busy (No Listen mode ongoing)
+  *             1  : Listen (Peripheral in Address Listen Mode)
+  *          b2     Intrinsic process state
+  *             0  : Ready
+  *             1  : Busy (Peripheral busy with some configuration or internal operations)
+  *          b1     Rx state
+  *             0  : Ready (no Rx operation ongoing)
+  *             1  : Busy (Rx operation ongoing)
+  *          b0     Tx state
+  *             0  : Ready (no Tx operation ongoing)
+  *             1  : Busy (Tx operation ongoing)
+  * @{
+  */
+typedef enum
+{
+  HAL_I2C_STATE_RESET             = 0x00U,   /*!< Peripheral is not yet Initialized         */
+  HAL_I2C_STATE_READY             = 0x20U,   /*!< Peripheral Initialized and ready for use  */
+  HAL_I2C_STATE_BUSY              = 0x24U,   /*!< An internal process is ongoing            */
+  HAL_I2C_STATE_BUSY_TX           = 0x21U,   /*!< Data Transmission process is ongoing      */
+  HAL_I2C_STATE_BUSY_RX           = 0x22U,   /*!< Data Reception process is ongoing         */
+  HAL_I2C_STATE_LISTEN            = 0x28U,   /*!< Address Listen Mode is ongoing            */
+  HAL_I2C_STATE_BUSY_TX_LISTEN    = 0x29U,   /*!< Address Listen Mode and Data Transmission
+                                                 process is ongoing                         */
+  HAL_I2C_STATE_BUSY_RX_LISTEN    = 0x2AU,   /*!< Address Listen Mode and Data Reception
+                                                 process is ongoing                         */
+  HAL_I2C_STATE_ABORT             = 0x60U,   /*!< Abort user request ongoing                */
+  HAL_I2C_STATE_TIMEOUT           = 0xA0U,   /*!< Timeout state                             */
+  HAL_I2C_STATE_ERROR             = 0xE0U    /*!< Error                                     */
+
+} HAL_I2C_StateTypeDef;
+
+/**
+  * @}
+  */
+
+/** @defgroup HAL_mode_structure_definition HAL mode structure definition
+  * @brief  HAL Mode structure definition
+  * @note  HAL I2C Mode value coding follow below described bitmap :\n
+  *          b7     (not used)\n
+  *             x  : Should be set to 0\n
+  *          b6\n
+  *             0  : None\n
+  *             1  : Memory (HAL I2C communication is in Memory Mode)\n
+  *          b5\n
+  *             0  : None\n
+  *             1  : Slave (HAL I2C communication is in Slave Mode)\n
+  *          b4\n
+  *             0  : None\n
+  *             1  : Master (HAL I2C communication is in Master Mode)\n
+  *          b3-b2-b1-b0  (not used)\n
+  *             xxxx : Should be set to 0000
+  * @{
+  */
+typedef enum
+{
+  HAL_I2C_MODE_NONE               = 0x00U,   /*!< No I2C communication on going             */
+  HAL_I2C_MODE_MASTER             = 0x10U,   /*!< I2C communication is in Master Mode       */
+  HAL_I2C_MODE_SLAVE              = 0x20U,   /*!< I2C communication is in Slave Mode        */
+  HAL_I2C_MODE_MEM                = 0x40U    /*!< I2C communication is in Memory Mode       */
+
+} HAL_I2C_ModeTypeDef;
+
+/**
+  * @}
+  */
+
+/** @defgroup I2C_Error_Code_definition I2C Error Code definition
+  * @brief  I2C Error Code definition
+  * @{
+  */
+#define HAL_I2C_ERROR_NONE              0x00000000U    /*!< No error              */
+#define HAL_I2C_ERROR_BERR              0x00000001U    /*!< BERR error            */
+#define HAL_I2C_ERROR_ARLO              0x00000002U    /*!< ARLO error            */
+#define HAL_I2C_ERROR_AF                0x00000004U    /*!< AF error              */
+#define HAL_I2C_ERROR_OVR               0x00000008U    /*!< OVR error             */
+#define HAL_I2C_ERROR_DMA               0x00000010U    /*!< DMA transfer error    */
+#define HAL_I2C_ERROR_TIMEOUT           0x00000020U    /*!< Timeout Error         */
+#define HAL_I2C_ERROR_SIZE              0x00000040U    /*!< Size Management error */
+#define HAL_I2C_ERROR_DMA_PARAM         0x00000080U    /*!< DMA Parameter Error   */
+#define HAL_I2C_WRONG_START             0x00000200U    /*!< Wrong start Error     */
+#if (USE_HAL_I2C_REGISTER_CALLBACKS == 1)
+#define HAL_I2C_ERROR_INVALID_CALLBACK  0x00000100U    /*!< Invalid Callback error */
+#endif /* USE_HAL_I2C_REGISTER_CALLBACKS */
+/**
+  * @}
+  */
+
+/** @defgroup I2C_handle_Structure_definition I2C handle Structure definition
+  * @brief  I2C handle Structure definition
+  * @{
+  */
+#if (USE_HAL_I2C_REGISTER_CALLBACKS == 1)
+typedef struct __I2C_HandleTypeDef
+#else
+typedef struct
+#endif  /* USE_HAL_I2C_REGISTER_CALLBACKS */
+{
+  I2C_TypeDef                *Instance;      /*!< I2C registers base address               */
+
+  I2C_InitTypeDef            Init;           /*!< I2C communication parameters             */
+
+  uint8_t                    *pBuffPtr;      /*!< Pointer to I2C transfer buffer           */
+
+  uint16_t                   XferSize;       /*!< I2C transfer size                        */
+
+  __IO uint16_t              XferCount;      /*!< I2C transfer counter                     */
+
+  __IO uint32_t              XferOptions;    /*!< I2C transfer options                     */
+
+  __IO uint32_t              PreviousState;  /*!< I2C communication Previous state and mode
+                                                  context for internal usage               */
+
+  DMA_HandleTypeDef          *hdmatx;        /*!< I2C Tx DMA handle parameters             */
+
+  DMA_HandleTypeDef          *hdmarx;        /*!< I2C Rx DMA handle parameters             */
+
+  HAL_LockTypeDef            Lock;           /*!< I2C locking object                       */
+
+  __IO HAL_I2C_StateTypeDef  State;          /*!< I2C communication state                  */
+
+  __IO HAL_I2C_ModeTypeDef   Mode;           /*!< I2C communication mode                   */
+
+  __IO uint32_t              ErrorCode;      /*!< I2C Error code                           */
+
+  __IO uint32_t              Devaddress;     /*!< I2C Target device address                */
+
+  __IO uint32_t              Memaddress;     /*!< I2C Target memory address                */
+
+  __IO uint32_t              MemaddSize;     /*!< I2C Target memory address  size          */
+
+  __IO uint32_t              EventCount;     /*!< I2C Event counter                        */
+
+
+#if (USE_HAL_I2C_REGISTER_CALLBACKS == 1)
+  void (* MasterTxCpltCallback)(struct __I2C_HandleTypeDef *hi2c);           /*!< I2C Master Tx Transfer completed callback */
+  void (* MasterRxCpltCallback)(struct __I2C_HandleTypeDef *hi2c);           /*!< I2C Master Rx Transfer completed callback */
+  void (* SlaveTxCpltCallback)(struct __I2C_HandleTypeDef *hi2c);            /*!< I2C Slave Tx Transfer completed callback  */
+  void (* SlaveRxCpltCallback)(struct __I2C_HandleTypeDef *hi2c);            /*!< I2C Slave Rx Transfer completed callback  */
+  void (* ListenCpltCallback)(struct __I2C_HandleTypeDef *hi2c);             /*!< I2C Listen Complete callback              */
+  void (* MemTxCpltCallback)(struct __I2C_HandleTypeDef *hi2c);              /*!< I2C Memory Tx Transfer completed callback */
+  void (* MemRxCpltCallback)(struct __I2C_HandleTypeDef *hi2c);              /*!< I2C Memory Rx Transfer completed callback */
+  void (* ErrorCallback)(struct __I2C_HandleTypeDef *hi2c);                  /*!< I2C Error callback                        */
+  void (* AbortCpltCallback)(struct __I2C_HandleTypeDef *hi2c);              /*!< I2C Abort callback                        */
+
+  void (* AddrCallback)(struct __I2C_HandleTypeDef *hi2c, uint8_t TransferDirection, uint16_t AddrMatchCode);  /*!< I2C Slave Address Match callback */
+
+  void (* MspInitCallback)(struct __I2C_HandleTypeDef *hi2c);                /*!< I2C Msp Init callback                     */
+  void (* MspDeInitCallback)(struct __I2C_HandleTypeDef *hi2c);              /*!< I2C Msp DeInit callback                   */
+
+#endif  /* USE_HAL_I2C_REGISTER_CALLBACKS */
+} I2C_HandleTypeDef;
+
+#if (USE_HAL_I2C_REGISTER_CALLBACKS == 1)
+/**
+  * @brief  HAL I2C Callback ID enumeration definition
+  */
+typedef enum
+{
+  HAL_I2C_MASTER_TX_COMPLETE_CB_ID      = 0x00U,    /*!< I2C Master Tx Transfer completed callback ID  */
+  HAL_I2C_MASTER_RX_COMPLETE_CB_ID      = 0x01U,    /*!< I2C Master Rx Transfer completed callback ID  */
+  HAL_I2C_SLAVE_TX_COMPLETE_CB_ID       = 0x02U,    /*!< I2C Slave Tx Transfer completed callback ID   */
+  HAL_I2C_SLAVE_RX_COMPLETE_CB_ID       = 0x03U,    /*!< I2C Slave Rx Transfer completed callback ID   */
+  HAL_I2C_LISTEN_COMPLETE_CB_ID         = 0x04U,    /*!< I2C Listen Complete callback ID               */
+  HAL_I2C_MEM_TX_COMPLETE_CB_ID         = 0x05U,    /*!< I2C Memory Tx Transfer callback ID            */
+  HAL_I2C_MEM_RX_COMPLETE_CB_ID         = 0x06U,    /*!< I2C Memory Rx Transfer completed callback ID  */
+  HAL_I2C_ERROR_CB_ID                   = 0x07U,    /*!< I2C Error callback ID                         */
+  HAL_I2C_ABORT_CB_ID                   = 0x08U,    /*!< I2C Abort callback ID                         */
+
+  HAL_I2C_MSPINIT_CB_ID                 = 0x09U,    /*!< I2C Msp Init callback ID                      */
+  HAL_I2C_MSPDEINIT_CB_ID               = 0x0AU     /*!< I2C Msp DeInit callback ID                    */
+
+} HAL_I2C_CallbackIDTypeDef;
+
+/**
+  * @brief  HAL I2C Callback pointer definition
+  */
+typedef  void (*pI2C_CallbackTypeDef)(I2C_HandleTypeDef *hi2c); /*!< pointer to an I2C callback function */
+typedef  void (*pI2C_AddrCallbackTypeDef)(I2C_HandleTypeDef *hi2c, uint8_t TransferDirection, uint16_t AddrMatchCode); /*!< pointer to an I2C Address Match callback function */
+
+#endif /* USE_HAL_I2C_REGISTER_CALLBACKS */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+/* Exported constants --------------------------------------------------------*/
+
+/** @defgroup I2C_Exported_Constants I2C Exported Constants
+  * @{
+  */
+
+/** @defgroup I2C_duty_cycle_in_fast_mode I2C duty cycle in fast mode
+  * @{
+  */
+#define I2C_DUTYCYCLE_2                 0x00000000U
+#define I2C_DUTYCYCLE_16_9              I2C_CCR_DUTY
+/**
+  * @}
+  */
+
+/** @defgroup I2C_addressing_mode I2C addressing mode
+  * @{
+  */
+#define I2C_ADDRESSINGMODE_7BIT         0x00004000U
+#define I2C_ADDRESSINGMODE_10BIT        (I2C_OAR1_ADDMODE | 0x00004000U)
+/**
+  * @}
+  */
+
+/** @defgroup I2C_dual_addressing_mode  I2C dual addressing mode
+  * @{
+  */
+#define I2C_DUALADDRESS_DISABLE        0x00000000U
+#define I2C_DUALADDRESS_ENABLE         I2C_OAR2_ENDUAL
+/**
+  * @}
+  */
+
+/** @defgroup I2C_general_call_addressing_mode I2C general call addressing mode
+  * @{
+  */
+#define I2C_GENERALCALL_DISABLE        0x00000000U
+#define I2C_GENERALCALL_ENABLE         I2C_CR1_ENGC
+/**
+  * @}
+  */
+
+/** @defgroup I2C_nostretch_mode I2C nostretch mode
+  * @{
+  */
+#define I2C_NOSTRETCH_DISABLE          0x00000000U
+#define I2C_NOSTRETCH_ENABLE           I2C_CR1_NOSTRETCH
+/**
+  * @}
+  */
+
+/** @defgroup I2C_Memory_Address_Size I2C Memory Address Size
+  * @{
+  */
+#define I2C_MEMADD_SIZE_8BIT            0x00000001U
+#define I2C_MEMADD_SIZE_16BIT           0x00000010U
+/**
+  * @}
+  */
+
+/** @defgroup I2C_XferDirection_definition I2C XferDirection definition
+  * @{
+  */
+#define I2C_DIRECTION_RECEIVE           0x00000000U
+#define I2C_DIRECTION_TRANSMIT          0x00000001U
+/**
+  * @}
+  */
+
+/** @defgroup I2C_XferOptions_definition I2C XferOptions definition
+  * @{
+  */
+#define  I2C_FIRST_FRAME                0x00000001U
+#define  I2C_FIRST_AND_NEXT_FRAME       0x00000002U
+#define  I2C_NEXT_FRAME                 0x00000004U
+#define  I2C_FIRST_AND_LAST_FRAME       0x00000008U
+#define  I2C_LAST_FRAME_NO_STOP         0x00000010U
+#define  I2C_LAST_FRAME                 0x00000020U
+
+/* List of XferOptions in usage of :
+ * 1- Restart condition in all use cases (direction change or not)
+ */
+#define  I2C_OTHER_FRAME                (0x00AA0000U)
+#define  I2C_OTHER_AND_LAST_FRAME       (0xAA000000U)
+/**
+  * @}
+  */
+
+/** @defgroup I2C_Interrupt_configuration_definition I2C Interrupt configuration definition
+  * @brief I2C Interrupt definition
+  *        Elements values convention: 0xXXXXXXXX
+  *           - XXXXXXXX  : Interrupt control mask
+  * @{
+  */
+#define I2C_IT_BUF                      I2C_CR2_ITBUFEN
+#define I2C_IT_EVT                      I2C_CR2_ITEVTEN
+#define I2C_IT_ERR                      I2C_CR2_ITERREN
+/**
+  * @}
+  */
+
+/** @defgroup I2C_Flag_definition I2C Flag definition
+  * @{
+  */
+
+#define I2C_FLAG_OVR                    0x00010800U
+#define I2C_FLAG_AF                     0x00010400U
+#define I2C_FLAG_ARLO                   0x00010200U
+#define I2C_FLAG_BERR                   0x00010100U
+#define I2C_FLAG_TXE                    0x00010080U
+#define I2C_FLAG_RXNE                   0x00010040U
+#define I2C_FLAG_STOPF                  0x00010010U
+#define I2C_FLAG_ADD10                  0x00010008U
+#define I2C_FLAG_BTF                    0x00010004U
+#define I2C_FLAG_ADDR                   0x00010002U
+#define I2C_FLAG_SB                     0x00010001U
+#define I2C_FLAG_DUALF                  0x00100080U
+#define I2C_FLAG_GENCALL                0x00100010U
+#define I2C_FLAG_TRA                    0x00100004U
+#define I2C_FLAG_BUSY                   0x00100002U
+#define I2C_FLAG_MSL                    0x00100001U
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Exported macros -----------------------------------------------------------*/
+
+/** @defgroup I2C_Exported_Macros I2C Exported Macros
+  * @{
+  */
+
+/** @brief Reset I2C handle state.
+  * @param  __HANDLE__ specifies the I2C Handle.
+  * @retval None
+  */
+#if (USE_HAL_I2C_REGISTER_CALLBACKS == 1)
+#define __HAL_I2C_RESET_HANDLE_STATE(__HANDLE__)                do{                                                   \
+                                                                    (__HANDLE__)->State = HAL_I2C_STATE_RESET;       \
+                                                                    (__HANDLE__)->MspInitCallback = NULL;            \
+                                                                    (__HANDLE__)->MspDeInitCallback = NULL;          \
+                                                                  } while(0)
+#else
+#define __HAL_I2C_RESET_HANDLE_STATE(__HANDLE__)                ((__HANDLE__)->State = HAL_I2C_STATE_RESET)
+#endif
+
+/** @brief  Enable or disable the specified I2C interrupts.
+  * @param  __HANDLE__ specifies the I2C Handle.
+  * @param  __INTERRUPT__ specifies the interrupt source to enable or disable.
+  *         This parameter can be one of the following values:
+  *            @arg I2C_IT_BUF: Buffer interrupt enable
+  *            @arg I2C_IT_EVT: Event interrupt enable
+  *            @arg I2C_IT_ERR: Error interrupt enable
+  * @retval None
+  */
+#define __HAL_I2C_ENABLE_IT(__HANDLE__, __INTERRUPT__)   SET_BIT((__HANDLE__)->Instance->CR2,(__INTERRUPT__))
+#define __HAL_I2C_DISABLE_IT(__HANDLE__, __INTERRUPT__)  CLEAR_BIT((__HANDLE__)->Instance->CR2, (__INTERRUPT__))
+
+/** @brief  Checks if the specified I2C interrupt source is enabled or disabled.
+  * @param  __HANDLE__ specifies the I2C Handle.
+  * @param  __INTERRUPT__ specifies the I2C interrupt source to check.
+  *          This parameter can be one of the following values:
+  *            @arg I2C_IT_BUF: Buffer interrupt enable
+  *            @arg I2C_IT_EVT: Event interrupt enable
+  *            @arg I2C_IT_ERR: Error interrupt enable
+  * @retval The new state of __INTERRUPT__ (TRUE or FALSE).
+  */
+#define __HAL_I2C_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__) ((((__HANDLE__)->Instance->CR2 & (__INTERRUPT__)) == (__INTERRUPT__)) ? SET : RESET)
+
+/** @brief  Checks whether the specified I2C flag is set or not.
+  * @param  __HANDLE__ specifies the I2C Handle.
+  * @param  __FLAG__ specifies the flag to check.
+  *         This parameter can be one of the following values:
+  *            @arg I2C_FLAG_OVR: Overrun/Underrun flag
+  *            @arg I2C_FLAG_AF: Acknowledge failure flag
+  *            @arg I2C_FLAG_ARLO: Arbitration lost flag
+  *            @arg I2C_FLAG_BERR: Bus error flag
+  *            @arg I2C_FLAG_TXE: Data register empty flag
+  *            @arg I2C_FLAG_RXNE: Data register not empty flag
+  *            @arg I2C_FLAG_STOPF: Stop detection flag
+  *            @arg I2C_FLAG_ADD10: 10-bit header sent flag
+  *            @arg I2C_FLAG_BTF: Byte transfer finished flag
+  *            @arg I2C_FLAG_ADDR: Address sent flag
+  *                                Address matched flag
+  *            @arg I2C_FLAG_SB: Start bit flag
+  *            @arg I2C_FLAG_DUALF: Dual flag
+  *            @arg I2C_FLAG_GENCALL: General call header flag
+  *            @arg I2C_FLAG_TRA: Transmitter/Receiver flag
+  *            @arg I2C_FLAG_BUSY: Bus busy flag
+  *            @arg I2C_FLAG_MSL: Master/Slave flag
+  * @retval The new state of __FLAG__ (TRUE or FALSE).
+  */
+#define __HAL_I2C_GET_FLAG(__HANDLE__, __FLAG__) ((((uint8_t)((__FLAG__) >> 16U)) == 0x01U) ? \
+                                                  (((((__HANDLE__)->Instance->SR1) & ((__FLAG__) & I2C_FLAG_MASK)) == ((__FLAG__) & I2C_FLAG_MASK)) ? SET : RESET) : \
+                                                  (((((__HANDLE__)->Instance->SR2) & ((__FLAG__) & I2C_FLAG_MASK)) == ((__FLAG__) & I2C_FLAG_MASK)) ? SET : RESET))
+
+/** @brief  Clears the I2C pending flags which are cleared by writing 0 in a specific bit.
+  * @param  __HANDLE__ specifies the I2C Handle.
+  * @param  __FLAG__ specifies the flag to clear.
+  *         This parameter can be any combination of the following values:
+  *            @arg I2C_FLAG_OVR: Overrun/Underrun flag (Slave mode)
+  *            @arg I2C_FLAG_AF: Acknowledge failure flag
+  *            @arg I2C_FLAG_ARLO: Arbitration lost flag (Master mode)
+  *            @arg I2C_FLAG_BERR: Bus error flag
+  * @retval None
+  */
+#define __HAL_I2C_CLEAR_FLAG(__HANDLE__, __FLAG__) ((__HANDLE__)->Instance->SR1 = ~((__FLAG__) & I2C_FLAG_MASK))
+
+/** @brief  Clears the I2C ADDR pending flag.
+  * @param  __HANDLE__ specifies the I2C Handle.
+  *         This parameter can be I2C where x: 1, 2, or 3 to select the I2C peripheral.
+  * @retval None
+  */
+#define __HAL_I2C_CLEAR_ADDRFLAG(__HANDLE__)    \
+  do{                                           \
+    __IO uint32_t tmpreg = 0x00U;               \
+    tmpreg = (__HANDLE__)->Instance->SR1;       \
+    tmpreg = (__HANDLE__)->Instance->SR2;       \
+    UNUSED(tmpreg);                             \
+  } while(0)
+
+/** @brief  Clears the I2C STOPF pending flag.
+  * @param  __HANDLE__ specifies the I2C Handle.
+  * @retval None
+  */
+#define __HAL_I2C_CLEAR_STOPFLAG(__HANDLE__)           \
+  do{                                                  \
+    __IO uint32_t tmpreg = 0x00U;                      \
+    tmpreg = (__HANDLE__)->Instance->SR1;              \
+    SET_BIT((__HANDLE__)->Instance->CR1, I2C_CR1_PE);  \
+    UNUSED(tmpreg);                                    \
+  } while(0)
+
+/** @brief  Enable the specified I2C peripheral.
+  * @param  __HANDLE__ specifies the I2C Handle.
+  * @retval None
+  */
+#define __HAL_I2C_ENABLE(__HANDLE__)                  SET_BIT((__HANDLE__)->Instance->CR1, I2C_CR1_PE)
+
+/** @brief  Disable the specified I2C peripheral.
+  * @param  __HANDLE__ specifies the I2C Handle.
+  * @retval None
+  */
+#define __HAL_I2C_DISABLE(__HANDLE__)                 CLEAR_BIT((__HANDLE__)->Instance->CR1, I2C_CR1_PE)
+
+/**
+  * @}
+  */
+
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup I2C_Exported_Functions
+  * @{
+  */
+
+/** @addtogroup I2C_Exported_Functions_Group1 Initialization and de-initialization functions
+  * @{
+  */
+/* Initialization and de-initialization functions******************************/
+HAL_StatusTypeDef HAL_I2C_Init(I2C_HandleTypeDef *hi2c);
+HAL_StatusTypeDef HAL_I2C_DeInit(I2C_HandleTypeDef *hi2c);
+void HAL_I2C_MspInit(I2C_HandleTypeDef *hi2c);
+void HAL_I2C_MspDeInit(I2C_HandleTypeDef *hi2c);
+
+/* Callbacks Register/UnRegister functions  ***********************************/
+#if (USE_HAL_I2C_REGISTER_CALLBACKS == 1)
+HAL_StatusTypeDef HAL_I2C_RegisterCallback(I2C_HandleTypeDef *hi2c, HAL_I2C_CallbackIDTypeDef CallbackID, pI2C_CallbackTypeDef pCallback);
+HAL_StatusTypeDef HAL_I2C_UnRegisterCallback(I2C_HandleTypeDef *hi2c, HAL_I2C_CallbackIDTypeDef CallbackID);
+
+HAL_StatusTypeDef HAL_I2C_RegisterAddrCallback(I2C_HandleTypeDef *hi2c, pI2C_AddrCallbackTypeDef pCallback);
+HAL_StatusTypeDef HAL_I2C_UnRegisterAddrCallback(I2C_HandleTypeDef *hi2c);
+#endif /* USE_HAL_I2C_REGISTER_CALLBACKS */
+/**
+  * @}
+  */
+
+/** @addtogroup I2C_Exported_Functions_Group2 Input and Output operation functions
+  * @{
+  */
+/* IO operation functions  ****************************************************/
+/******* Blocking mode: Polling */
+HAL_StatusTypeDef HAL_I2C_Master_Transmit(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData, uint16_t Size, uint32_t Timeout);
+HAL_StatusTypeDef HAL_I2C_Master_Receive(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData, uint16_t Size, uint32_t Timeout);
+HAL_StatusTypeDef HAL_I2C_Slave_Transmit(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size, uint32_t Timeout);
+HAL_StatusTypeDef HAL_I2C_Slave_Receive(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size, uint32_t Timeout);
+HAL_StatusTypeDef HAL_I2C_Mem_Write(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress, uint16_t MemAddSize, uint8_t *pData, uint16_t Size, uint32_t Timeout);
+HAL_StatusTypeDef HAL_I2C_Mem_Read(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress, uint16_t MemAddSize, uint8_t *pData, uint16_t Size, uint32_t Timeout);
+HAL_StatusTypeDef HAL_I2C_IsDeviceReady(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint32_t Trials, uint32_t Timeout);
+
+/******* Non-Blocking mode: Interrupt */
+HAL_StatusTypeDef HAL_I2C_Master_Transmit_IT(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_I2C_Master_Receive_IT(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_I2C_Slave_Transmit_IT(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_I2C_Slave_Receive_IT(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_I2C_Mem_Write_IT(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress, uint16_t MemAddSize, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_I2C_Mem_Read_IT(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress, uint16_t MemAddSize, uint8_t *pData, uint16_t Size);
+
+HAL_StatusTypeDef HAL_I2C_Master_Seq_Transmit_IT(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData, uint16_t Size, uint32_t XferOptions);
+HAL_StatusTypeDef HAL_I2C_Master_Seq_Receive_IT(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData, uint16_t Size, uint32_t XferOptions);
+HAL_StatusTypeDef HAL_I2C_Slave_Seq_Transmit_IT(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size, uint32_t XferOptions);
+HAL_StatusTypeDef HAL_I2C_Slave_Seq_Receive_IT(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size, uint32_t XferOptions);
+HAL_StatusTypeDef HAL_I2C_EnableListen_IT(I2C_HandleTypeDef *hi2c);
+HAL_StatusTypeDef HAL_I2C_DisableListen_IT(I2C_HandleTypeDef *hi2c);
+HAL_StatusTypeDef HAL_I2C_Master_Abort_IT(I2C_HandleTypeDef *hi2c, uint16_t DevAddress);
+
+/******* Non-Blocking mode: DMA */
+HAL_StatusTypeDef HAL_I2C_Master_Transmit_DMA(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_I2C_Master_Receive_DMA(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_I2C_Slave_Transmit_DMA(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_I2C_Slave_Receive_DMA(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_I2C_Mem_Write_DMA(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress, uint16_t MemAddSize, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_I2C_Mem_Read_DMA(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress, uint16_t MemAddSize, uint8_t *pData, uint16_t Size);
+
+HAL_StatusTypeDef HAL_I2C_Master_Seq_Transmit_DMA(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData, uint16_t Size, uint32_t XferOptions);
+HAL_StatusTypeDef HAL_I2C_Master_Seq_Receive_DMA(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData, uint16_t Size, uint32_t XferOptions);
+HAL_StatusTypeDef HAL_I2C_Slave_Seq_Transmit_DMA(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size, uint32_t XferOptions);
+HAL_StatusTypeDef HAL_I2C_Slave_Seq_Receive_DMA(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size, uint32_t XferOptions);
+/**
+  * @}
+  */
+
+/** @addtogroup I2C_IRQ_Handler_and_Callbacks IRQ Handler and Callbacks
+ * @{
+ */
+/******* I2C IRQHandler and Callbacks used in non blocking modes (Interrupt and DMA) */
+void HAL_I2C_EV_IRQHandler(I2C_HandleTypeDef *hi2c);
+void HAL_I2C_ER_IRQHandler(I2C_HandleTypeDef *hi2c);
+void HAL_I2C_MasterTxCpltCallback(I2C_HandleTypeDef *hi2c);
+void HAL_I2C_MasterRxCpltCallback(I2C_HandleTypeDef *hi2c);
+void HAL_I2C_SlaveTxCpltCallback(I2C_HandleTypeDef *hi2c);
+void HAL_I2C_SlaveRxCpltCallback(I2C_HandleTypeDef *hi2c);
+void HAL_I2C_AddrCallback(I2C_HandleTypeDef *hi2c, uint8_t TransferDirection, uint16_t AddrMatchCode);
+void HAL_I2C_ListenCpltCallback(I2C_HandleTypeDef *hi2c);
+void HAL_I2C_MemTxCpltCallback(I2C_HandleTypeDef *hi2c);
+void HAL_I2C_MemRxCpltCallback(I2C_HandleTypeDef *hi2c);
+void HAL_I2C_ErrorCallback(I2C_HandleTypeDef *hi2c);
+void HAL_I2C_AbortCpltCallback(I2C_HandleTypeDef *hi2c);
+/**
+  * @}
+  */
+
+/** @addtogroup I2C_Exported_Functions_Group3 Peripheral State, Mode and Error functions
+  * @{
+  */
+/* Peripheral State, Mode and Error functions  *********************************/
+HAL_I2C_StateTypeDef HAL_I2C_GetState(I2C_HandleTypeDef *hi2c);
+HAL_I2C_ModeTypeDef HAL_I2C_GetMode(I2C_HandleTypeDef *hi2c);
+uint32_t HAL_I2C_GetError(I2C_HandleTypeDef *hi2c);
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+/* Private types -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private constants ---------------------------------------------------------*/
+/** @defgroup I2C_Private_Constants I2C Private Constants
+  * @{
+  */
+#define I2C_FLAG_MASK                    0x0000FFFFU
+#define I2C_MIN_PCLK_FREQ_STANDARD       2000000U     /*!< 2 MHz                     */
+#define I2C_MIN_PCLK_FREQ_FAST           4000000U     /*!< 4 MHz                     */
+/**
+  * @}
+  */
+
+/* Private macros ------------------------------------------------------------*/
+/** @defgroup I2C_Private_Macros I2C Private Macros
+  * @{
+  */
+
+#define I2C_MIN_PCLK_FREQ(__PCLK__, __SPEED__)             (((__SPEED__) <= 100000U) ? ((__PCLK__) < I2C_MIN_PCLK_FREQ_STANDARD) : ((__PCLK__) < I2C_MIN_PCLK_FREQ_FAST))
+#define I2C_CCR_CALCULATION(__PCLK__, __SPEED__, __COEFF__)     (((((__PCLK__) - 1U)/((__SPEED__) * (__COEFF__))) + 1U) & I2C_CCR_CCR)
+#define I2C_FREQRANGE(__PCLK__)                            ((__PCLK__)/1000000U)
+#define I2C_RISE_TIME(__FREQRANGE__, __SPEED__)            (((__SPEED__) <= 100000U) ? ((__FREQRANGE__) + 1U) : ((((__FREQRANGE__) * 300U) / 1000U) + 1U))
+#define I2C_SPEED_STANDARD(__PCLK__, __SPEED__)            ((I2C_CCR_CALCULATION((__PCLK__), (__SPEED__), 2U) < 4U)? 4U:I2C_CCR_CALCULATION((__PCLK__), (__SPEED__), 2U))
+#define I2C_SPEED_FAST(__PCLK__, __SPEED__, __DUTYCYCLE__) (((__DUTYCYCLE__) == I2C_DUTYCYCLE_2)? I2C_CCR_CALCULATION((__PCLK__), (__SPEED__), 3U) : (I2C_CCR_CALCULATION((__PCLK__), (__SPEED__), 25U) | I2C_DUTYCYCLE_16_9))
+#define I2C_SPEED(__PCLK__, __SPEED__, __DUTYCYCLE__)      (((__SPEED__) <= 100000U)? (I2C_SPEED_STANDARD((__PCLK__), (__SPEED__))) : \
+                                                                  ((I2C_SPEED_FAST((__PCLK__), (__SPEED__), (__DUTYCYCLE__)) & I2C_CCR_CCR) == 0U)? 1U : \
+                                                                  ((I2C_SPEED_FAST((__PCLK__), (__SPEED__), (__DUTYCYCLE__))) | I2C_CCR_FS))
+
+#define I2C_7BIT_ADD_WRITE(__ADDRESS__)                    ((uint8_t)((__ADDRESS__) & (uint8_t)(~I2C_OAR1_ADD0)))
+#define I2C_7BIT_ADD_READ(__ADDRESS__)                     ((uint8_t)((__ADDRESS__) | I2C_OAR1_ADD0))
+
+#define I2C_10BIT_ADDRESS(__ADDRESS__)                     ((uint8_t)((uint16_t)((__ADDRESS__) & (uint16_t)0x00FF)))
+#define I2C_10BIT_HEADER_WRITE(__ADDRESS__)                ((uint8_t)((uint16_t)((uint16_t)(((uint16_t)((__ADDRESS__) & (uint16_t)0x0300)) >> 7) | (uint16_t)0x00F0)))
+#define I2C_10BIT_HEADER_READ(__ADDRESS__)                 ((uint8_t)((uint16_t)((uint16_t)(((uint16_t)((__ADDRESS__) & (uint16_t)0x0300)) >> 7) | (uint16_t)(0x00F1))))
+
+#define I2C_MEM_ADD_MSB(__ADDRESS__)                       ((uint8_t)((uint16_t)(((uint16_t)((__ADDRESS__) & (uint16_t)0xFF00)) >> 8)))
+#define I2C_MEM_ADD_LSB(__ADDRESS__)                       ((uint8_t)((uint16_t)((__ADDRESS__) & (uint16_t)0x00FF)))
+
+/** @defgroup I2C_IS_RTC_Definitions I2C Private macros to check input parameters
+  * @{
+  */
+#define IS_I2C_DUTY_CYCLE(CYCLE) (((CYCLE) == I2C_DUTYCYCLE_2) || \
+                                  ((CYCLE) == I2C_DUTYCYCLE_16_9))
+#define IS_I2C_ADDRESSING_MODE(ADDRESS) (((ADDRESS) == I2C_ADDRESSINGMODE_7BIT) || \
+                                         ((ADDRESS) == I2C_ADDRESSINGMODE_10BIT))
+#define IS_I2C_DUAL_ADDRESS(ADDRESS) (((ADDRESS) == I2C_DUALADDRESS_DISABLE) || \
+                                      ((ADDRESS) == I2C_DUALADDRESS_ENABLE))
+#define IS_I2C_GENERAL_CALL(CALL) (((CALL) == I2C_GENERALCALL_DISABLE) || \
+                                   ((CALL) == I2C_GENERALCALL_ENABLE))
+#define IS_I2C_NO_STRETCH(STRETCH) (((STRETCH) == I2C_NOSTRETCH_DISABLE) || \
+                                    ((STRETCH) == I2C_NOSTRETCH_ENABLE))
+#define IS_I2C_MEMADD_SIZE(SIZE) (((SIZE) == I2C_MEMADD_SIZE_8BIT) || \
+                                  ((SIZE) == I2C_MEMADD_SIZE_16BIT))
+#define IS_I2C_CLOCK_SPEED(SPEED) (((SPEED) > 0U) && ((SPEED) <= 400000U))
+#define IS_I2C_OWN_ADDRESS1(ADDRESS1) (((ADDRESS1) & 0xFFFFFC00U) == 0U)
+#define IS_I2C_OWN_ADDRESS2(ADDRESS2) (((ADDRESS2) & 0xFFFFFF01U) == 0U)
+#define IS_I2C_TRANSFER_OPTIONS_REQUEST(REQUEST)      (((REQUEST) == I2C_FIRST_FRAME)              || \
+                                                       ((REQUEST) == I2C_FIRST_AND_NEXT_FRAME)     || \
+                                                       ((REQUEST) == I2C_NEXT_FRAME)               || \
+                                                       ((REQUEST) == I2C_FIRST_AND_LAST_FRAME)     || \
+                                                       ((REQUEST) == I2C_LAST_FRAME)               || \
+                                                       ((REQUEST) == I2C_LAST_FRAME_NO_STOP)       || \
+                                                       IS_I2C_TRANSFER_OTHER_OPTIONS_REQUEST(REQUEST))
+
+#define IS_I2C_TRANSFER_OTHER_OPTIONS_REQUEST(REQUEST) (((REQUEST) == I2C_OTHER_FRAME)     || \
+                                                        ((REQUEST) == I2C_OTHER_AND_LAST_FRAME))
+
+#define I2C_CHECK_FLAG(__ISR__, __FLAG__)         ((((__ISR__) & ((__FLAG__) & I2C_FLAG_MASK)) == ((__FLAG__) & I2C_FLAG_MASK)) ? SET : RESET)
+#define I2C_CHECK_IT_SOURCE(__CR1__, __IT__)      ((((__CR1__) & (__IT__)) == (__IT__)) ? SET : RESET)
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Private functions ---------------------------------------------------------*/
+/** @defgroup I2C_Private_Functions I2C Private Functions
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+
+#endif /* __STM32F1xx_HAL_I2C_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_i2s.h

@@ -0,0 +1,556 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_hal_i2s.h
+  * @author  MCD Application Team
+  * @brief   Header file of I2S HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef STM32F1xx_HAL_I2S_H
+#define STM32F1xx_HAL_I2S_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_hal_def.h"
+
+#if defined(SPI_I2S_SUPPORT)
+/** @addtogroup STM32F1xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup I2S
+  * @{
+  */
+
+/* Exported types ------------------------------------------------------------*/
+/** @defgroup I2S_Exported_Types I2S Exported Types
+  * @{
+  */
+
+/**
+  * @brief I2S Init structure definition
+  */
+typedef struct
+{
+  uint32_t Mode;                /*!< Specifies the I2S operating mode.
+                                     This parameter can be a value of @ref I2S_Mode */
+
+  uint32_t Standard;            /*!< Specifies the standard used for the I2S communication.
+                                     This parameter can be a value of @ref I2S_Standard */
+
+  uint32_t DataFormat;          /*!< Specifies the data format for the I2S communication.
+                                     This parameter can be a value of @ref I2S_Data_Format */
+
+  uint32_t MCLKOutput;          /*!< Specifies whether the I2S MCLK output is enabled or not.
+                                     This parameter can be a value of @ref I2S_MCLK_Output */
+
+  uint32_t AudioFreq;           /*!< Specifies the frequency selected for the I2S communication.
+                                     This parameter can be a value of @ref I2S_Audio_Frequency */
+
+  uint32_t CPOL;                /*!< Specifies the idle state of the I2S clock.
+                                     This parameter can be a value of @ref I2S_Clock_Polarity */
+} I2S_InitTypeDef;
+
+/**
+  * @brief  HAL State structures definition
+  */
+typedef enum
+{
+  HAL_I2S_STATE_RESET      = 0x00U,  /*!< I2S not yet initialized or disabled                */
+  HAL_I2S_STATE_READY      = 0x01U,  /*!< I2S initialized and ready for use                  */
+  HAL_I2S_STATE_BUSY       = 0x02U,  /*!< I2S internal process is ongoing                    */
+  HAL_I2S_STATE_BUSY_TX    = 0x03U,  /*!< Data Transmission process is ongoing               */
+  HAL_I2S_STATE_BUSY_RX    = 0x04U,  /*!< Data Reception process is ongoing                  */
+  HAL_I2S_STATE_TIMEOUT    = 0x06U,  /*!< I2S timeout state                                  */
+  HAL_I2S_STATE_ERROR      = 0x07U   /*!< I2S error state                                    */
+} HAL_I2S_StateTypeDef;
+
+/**
+  * @brief I2S handle Structure definition
+  */
+#if (USE_HAL_I2S_REGISTER_CALLBACKS == 1)
+typedef struct __I2S_HandleTypeDef
+#else
+typedef struct
+#endif /* USE_HAL_I2S_REGISTER_CALLBACKS */
+{
+  SPI_TypeDef                *Instance;    /*!< I2S registers base address */
+
+  I2S_InitTypeDef            Init;         /*!< I2S communication parameters */
+
+  uint16_t                   *pTxBuffPtr;  /*!< Pointer to I2S Tx transfer buffer */
+
+  __IO uint16_t              TxXferSize;   /*!< I2S Tx transfer size */
+
+  __IO uint16_t              TxXferCount;  /*!< I2S Tx transfer Counter */
+
+  uint16_t                   *pRxBuffPtr;  /*!< Pointer to I2S Rx transfer buffer */
+
+  __IO uint16_t              RxXferSize;   /*!< I2S Rx transfer size */
+
+  __IO uint16_t              RxXferCount;  /*!< I2S Rx transfer counter
+                                              (This field is initialized at the
+                                               same value as transfer size at the
+                                               beginning of the transfer and
+                                               decremented when a sample is received
+                                               NbSamplesReceived = RxBufferSize-RxBufferCount) */
+  DMA_HandleTypeDef          *hdmatx;      /*!< I2S Tx DMA handle parameters */
+
+  DMA_HandleTypeDef          *hdmarx;      /*!< I2S Rx DMA handle parameters */
+
+  __IO HAL_LockTypeDef       Lock;         /*!< I2S locking object */
+
+  __IO HAL_I2S_StateTypeDef  State;        /*!< I2S communication state */
+
+  __IO uint32_t              ErrorCode;    /*!< I2S Error code
+                                                This parameter can be a value of @ref I2S_Error */
+
+#if (USE_HAL_I2S_REGISTER_CALLBACKS == 1U)
+  void (* TxCpltCallback)(struct __I2S_HandleTypeDef *hi2s);             /*!< I2S Tx Completed callback          */
+  void (* RxCpltCallback)(struct __I2S_HandleTypeDef *hi2s);             /*!< I2S Rx Completed callback          */
+  void (* TxHalfCpltCallback)(struct __I2S_HandleTypeDef *hi2s);         /*!< I2S Tx Half Completed callback     */
+  void (* RxHalfCpltCallback)(struct __I2S_HandleTypeDef *hi2s);         /*!< I2S Rx Half Completed callback     */
+  void (* ErrorCallback)(struct __I2S_HandleTypeDef *hi2s);              /*!< I2S Error callback                 */
+  void (* MspInitCallback)(struct __I2S_HandleTypeDef *hi2s);            /*!< I2S Msp Init callback              */
+  void (* MspDeInitCallback)(struct __I2S_HandleTypeDef *hi2s);          /*!< I2S Msp DeInit callback            */
+
+#endif  /* USE_HAL_I2S_REGISTER_CALLBACKS */
+} I2S_HandleTypeDef;
+
+#if (USE_HAL_I2S_REGISTER_CALLBACKS == 1U)
+/**
+  * @brief  HAL I2S Callback ID enumeration definition
+  */
+typedef enum
+{
+  HAL_I2S_TX_COMPLETE_CB_ID             = 0x00U,    /*!< I2S Tx Completed callback ID         */
+  HAL_I2S_RX_COMPLETE_CB_ID             = 0x01U,    /*!< I2S Rx Completed callback ID         */
+  HAL_I2S_TX_HALF_COMPLETE_CB_ID        = 0x03U,    /*!< I2S Tx Half Completed callback ID    */
+  HAL_I2S_RX_HALF_COMPLETE_CB_ID        = 0x04U,    /*!< I2S Rx Half Completed callback ID    */
+  HAL_I2S_ERROR_CB_ID                   = 0x06U,    /*!< I2S Error callback ID                */
+  HAL_I2S_MSPINIT_CB_ID                 = 0x07U,    /*!< I2S Msp Init callback ID             */
+  HAL_I2S_MSPDEINIT_CB_ID               = 0x08U     /*!< I2S Msp DeInit callback ID           */
+
+} HAL_I2S_CallbackIDTypeDef;
+
+/**
+  * @brief  HAL I2S Callback pointer definition
+  */
+typedef  void (*pI2S_CallbackTypeDef)(I2S_HandleTypeDef *hi2s); /*!< pointer to an I2S callback function */
+
+#endif /* USE_HAL_I2S_REGISTER_CALLBACKS */
+/**
+  * @}
+  */
+
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup I2S_Exported_Constants I2S Exported Constants
+  * @{
+  */
+/** @defgroup I2S_Error I2S Error
+  * @{
+  */
+#define HAL_I2S_ERROR_NONE               (0x00000000U)  /*!< No error                    */
+#define HAL_I2S_ERROR_TIMEOUT            (0x00000001U)  /*!< Timeout error               */
+#define HAL_I2S_ERROR_OVR                (0x00000002U)  /*!< OVR error                   */
+#define HAL_I2S_ERROR_UDR                (0x00000004U)  /*!< UDR error                   */
+#define HAL_I2S_ERROR_DMA                (0x00000008U)  /*!< DMA transfer error          */
+#define HAL_I2S_ERROR_PRESCALER          (0x00000010U)  /*!< Prescaler Calculation error */
+#if (USE_HAL_I2S_REGISTER_CALLBACKS == 1U)
+#define HAL_I2S_ERROR_INVALID_CALLBACK   (0x00000020U)  /*!< Invalid Callback error      */
+#endif /* USE_HAL_I2S_REGISTER_CALLBACKS */
+#define HAL_I2S_ERROR_BUSY_LINE_RX       (0x00000040U)  /*!< Busy Rx Line error          */
+/**
+  * @}
+  */
+
+/** @defgroup I2S_Mode I2S Mode
+  * @{
+  */
+#define I2S_MODE_SLAVE_TX                (0x00000000U)
+#define I2S_MODE_SLAVE_RX                (SPI_I2SCFGR_I2SCFG_0)
+#define I2S_MODE_MASTER_TX               (SPI_I2SCFGR_I2SCFG_1)
+#define I2S_MODE_MASTER_RX               ((SPI_I2SCFGR_I2SCFG_0 | SPI_I2SCFGR_I2SCFG_1))
+/**
+  * @}
+  */
+
+/** @defgroup I2S_Standard I2S Standard
+  * @{
+  */
+#define I2S_STANDARD_PHILIPS             (0x00000000U)
+#define I2S_STANDARD_MSB                 (SPI_I2SCFGR_I2SSTD_0)
+#define I2S_STANDARD_LSB                 (SPI_I2SCFGR_I2SSTD_1)
+#define I2S_STANDARD_PCM_SHORT           ((SPI_I2SCFGR_I2SSTD_0 | SPI_I2SCFGR_I2SSTD_1))
+#define I2S_STANDARD_PCM_LONG            ((SPI_I2SCFGR_I2SSTD_0 | SPI_I2SCFGR_I2SSTD_1 | SPI_I2SCFGR_PCMSYNC))
+/**
+  * @}
+  */
+
+/** @defgroup I2S_Data_Format I2S Data Format
+  * @{
+  */
+#define I2S_DATAFORMAT_16B               (0x00000000U)
+#define I2S_DATAFORMAT_16B_EXTENDED      (SPI_I2SCFGR_CHLEN)
+#define I2S_DATAFORMAT_24B               ((SPI_I2SCFGR_CHLEN | SPI_I2SCFGR_DATLEN_0))
+#define I2S_DATAFORMAT_32B               ((SPI_I2SCFGR_CHLEN | SPI_I2SCFGR_DATLEN_1))
+/**
+  * @}
+  */
+
+/** @defgroup I2S_MCLK_Output I2S MCLK Output
+  * @{
+  */
+#define I2S_MCLKOUTPUT_ENABLE            (SPI_I2SPR_MCKOE)
+#define I2S_MCLKOUTPUT_DISABLE           (0x00000000U)
+/**
+  * @}
+  */
+
+/** @defgroup I2S_Audio_Frequency I2S Audio Frequency
+  * @{
+  */
+#define I2S_AUDIOFREQ_192K               (192000U)
+#define I2S_AUDIOFREQ_96K                (96000U)
+#define I2S_AUDIOFREQ_48K                (48000U)
+#define I2S_AUDIOFREQ_44K                (44100U)
+#define I2S_AUDIOFREQ_32K                (32000U)
+#define I2S_AUDIOFREQ_22K                (22050U)
+#define I2S_AUDIOFREQ_16K                (16000U)
+#define I2S_AUDIOFREQ_11K                (11025U)
+#define I2S_AUDIOFREQ_8K                 (8000U)
+#define I2S_AUDIOFREQ_DEFAULT            (2U)
+/**
+  * @}
+  */
+
+/** @defgroup I2S_Clock_Polarity I2S Clock Polarity
+  * @{
+  */
+#define I2S_CPOL_LOW                     (0x00000000U)
+#define I2S_CPOL_HIGH                    (SPI_I2SCFGR_CKPOL)
+/**
+  * @}
+  */
+
+/** @defgroup I2S_Interrupts_Definition I2S Interrupts Definition
+  * @{
+  */
+#define I2S_IT_TXE                       SPI_CR2_TXEIE
+#define I2S_IT_RXNE                      SPI_CR2_RXNEIE
+#define I2S_IT_ERR                       SPI_CR2_ERRIE
+/**
+  * @}
+  */
+
+/** @defgroup I2S_Flags_Definition I2S Flags Definition
+  * @{
+  */
+#define I2S_FLAG_TXE                     SPI_SR_TXE
+#define I2S_FLAG_RXNE                    SPI_SR_RXNE
+
+#define I2S_FLAG_UDR                     SPI_SR_UDR
+#define I2S_FLAG_OVR                     SPI_SR_OVR
+#define I2S_FLAG_FRE                     SPI_SR_FRE
+
+#define I2S_FLAG_CHSIDE                  SPI_SR_CHSIDE
+#define I2S_FLAG_BSY                     SPI_SR_BSY
+
+#define I2S_FLAG_MASK                   (SPI_SR_RXNE\
+                                         | SPI_SR_TXE | SPI_SR_UDR | SPI_SR_OVR | SPI_SR_CHSIDE | SPI_SR_BSY)
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Exported macros -----------------------------------------------------------*/
+/** @defgroup I2S_Exported_macros I2S Exported Macros
+  * @{
+  */
+
+/** @brief  Reset I2S handle state
+  * @param  __HANDLE__ specifies the I2S Handle.
+  * @retval None
+  */
+#if (USE_HAL_I2S_REGISTER_CALLBACKS == 1U)
+#define __HAL_I2S_RESET_HANDLE_STATE(__HANDLE__)                do{                                                  \
+                                                                    (__HANDLE__)->State = HAL_I2S_STATE_RESET;       \
+                                                                    (__HANDLE__)->MspInitCallback = NULL;            \
+                                                                    (__HANDLE__)->MspDeInitCallback = NULL;          \
+                                                                  } while(0)
+#else
+#define __HAL_I2S_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_I2S_STATE_RESET)
+#endif /* USE_HAL_I2S_REGISTER_CALLBACKS */
+
+/** @brief  Enable the specified SPI peripheral (in I2S mode).
+  * @param  __HANDLE__ specifies the I2S Handle.
+  * @retval None
+  */
+#define __HAL_I2S_ENABLE(__HANDLE__)    (SET_BIT((__HANDLE__)->Instance->I2SCFGR, SPI_I2SCFGR_I2SE))
+
+/** @brief  Disable the specified SPI peripheral (in I2S mode).
+  * @param  __HANDLE__ specifies the I2S Handle.
+  * @retval None
+  */
+#define __HAL_I2S_DISABLE(__HANDLE__) (CLEAR_BIT((__HANDLE__)->Instance->I2SCFGR, SPI_I2SCFGR_I2SE))
+
+/** @brief  Enable the specified I2S interrupts.
+  * @param  __HANDLE__ specifies the I2S Handle.
+  * @param  __INTERRUPT__ specifies the interrupt source to enable or disable.
+  *         This parameter can be one of the following values:
+  *            @arg I2S_IT_TXE: Tx buffer empty interrupt enable
+  *            @arg I2S_IT_RXNE: RX buffer not empty interrupt enable
+  *            @arg I2S_IT_ERR: Error interrupt enable
+  * @retval None
+  */
+#define __HAL_I2S_ENABLE_IT(__HANDLE__, __INTERRUPT__)    (SET_BIT((__HANDLE__)->Instance->CR2,(__INTERRUPT__)))
+
+/** @brief  Disable the specified I2S interrupts.
+  * @param  __HANDLE__ specifies the I2S Handle.
+  * @param  __INTERRUPT__ specifies the interrupt source to enable or disable.
+  *         This parameter can be one of the following values:
+  *            @arg I2S_IT_TXE: Tx buffer empty interrupt enable
+  *            @arg I2S_IT_RXNE: RX buffer not empty interrupt enable
+  *            @arg I2S_IT_ERR: Error interrupt enable
+  * @retval None
+  */
+#define __HAL_I2S_DISABLE_IT(__HANDLE__, __INTERRUPT__) (CLEAR_BIT((__HANDLE__)->Instance->CR2,(__INTERRUPT__)))
+
+/** @brief  Checks if the specified I2S interrupt source is enabled or disabled.
+  * @param  __HANDLE__ specifies the I2S Handle.
+  *         This parameter can be I2S where x: 1, 2, or 3 to select the I2S peripheral.
+  * @param  __INTERRUPT__ specifies the I2S interrupt source to check.
+  *          This parameter can be one of the following values:
+  *            @arg I2S_IT_TXE: Tx buffer empty interrupt enable
+  *            @arg I2S_IT_RXNE: RX buffer not empty interrupt enable
+  *            @arg I2S_IT_ERR: Error interrupt enable
+  * @retval The new state of __IT__ (TRUE or FALSE).
+  */
+#define __HAL_I2S_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__) ((((__HANDLE__)->Instance->CR2\
+                                                              & (__INTERRUPT__)) == (__INTERRUPT__)) ? SET : RESET)
+
+/** @brief  Checks whether the specified I2S flag is set or not.
+  * @param  __HANDLE__ specifies the I2S Handle.
+  * @param  __FLAG__ specifies the flag to check.
+  *         This parameter can be one of the following values:
+  *            @arg I2S_FLAG_RXNE: Receive buffer not empty flag
+  *            @arg I2S_FLAG_TXE: Transmit buffer empty flag
+  *            @arg I2S_FLAG_UDR: Underrun flag
+  *            @arg I2S_FLAG_OVR: Overrun flag
+  *            @arg I2S_FLAG_FRE: Frame error flag
+  *            @arg I2S_FLAG_CHSIDE: Channel Side flag
+  *            @arg I2S_FLAG_BSY: Busy flag
+  * @retval The new state of __FLAG__ (TRUE or FALSE).
+  */
+#define __HAL_I2S_GET_FLAG(__HANDLE__, __FLAG__) ((((__HANDLE__)->Instance->SR) & (__FLAG__)) == (__FLAG__))
+
+/** @brief Clears the I2S OVR pending flag.
+  * @param  __HANDLE__ specifies the I2S Handle.
+  * @retval None
+  */
+#define __HAL_I2S_CLEAR_OVRFLAG(__HANDLE__) do{ \
+                                                __IO uint32_t tmpreg_ovr = 0x00U; \
+                                                tmpreg_ovr = (__HANDLE__)->Instance->DR; \
+                                                tmpreg_ovr = (__HANDLE__)->Instance->SR; \
+                                                UNUSED(tmpreg_ovr); \
+                                              }while(0U)
+/** @brief Clears the I2S UDR pending flag.
+  * @param  __HANDLE__ specifies the I2S Handle.
+  * @retval None
+  */
+#define __HAL_I2S_CLEAR_UDRFLAG(__HANDLE__) do{\
+                                                __IO uint32_t tmpreg_udr = 0x00U;\
+                                                tmpreg_udr = ((__HANDLE__)->Instance->SR);\
+                                                UNUSED(tmpreg_udr); \
+                                              }while(0U)
+/** @brief Flush the I2S DR Register.
+  * @param  __HANDLE__ specifies the I2S Handle.
+  * @retval None
+  */
+#define __HAL_I2S_FLUSH_RX_DR(__HANDLE__)  do{\
+                                                __IO uint32_t tmpreg_dr = 0x00U;\
+                                                tmpreg_dr = ((__HANDLE__)->Instance->DR);\
+                                                UNUSED(tmpreg_dr); \
+                                              }while(0U)
+/**
+  * @}
+  */
+
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup I2S_Exported_Functions
+  * @{
+  */
+
+/** @addtogroup I2S_Exported_Functions_Group1
+  * @{
+  */
+/* Initialization/de-initialization functions  ********************************/
+HAL_StatusTypeDef HAL_I2S_Init(I2S_HandleTypeDef *hi2s);
+HAL_StatusTypeDef HAL_I2S_DeInit(I2S_HandleTypeDef *hi2s);
+void HAL_I2S_MspInit(I2S_HandleTypeDef *hi2s);
+void HAL_I2S_MspDeInit(I2S_HandleTypeDef *hi2s);
+
+/* Callbacks Register/UnRegister functions  ***********************************/
+#if (USE_HAL_I2S_REGISTER_CALLBACKS == 1U)
+HAL_StatusTypeDef HAL_I2S_RegisterCallback(I2S_HandleTypeDef *hi2s, HAL_I2S_CallbackIDTypeDef CallbackID,
+                                           pI2S_CallbackTypeDef pCallback);
+HAL_StatusTypeDef HAL_I2S_UnRegisterCallback(I2S_HandleTypeDef *hi2s, HAL_I2S_CallbackIDTypeDef CallbackID);
+#endif /* USE_HAL_I2S_REGISTER_CALLBACKS */
+/**
+  * @}
+  */
+
+/** @addtogroup I2S_Exported_Functions_Group2
+  * @{
+  */
+/* I/O operation functions  ***************************************************/
+/* Blocking mode: Polling */
+HAL_StatusTypeDef HAL_I2S_Transmit(I2S_HandleTypeDef *hi2s, uint16_t *pData, uint16_t Size, uint32_t Timeout);
+HAL_StatusTypeDef HAL_I2S_Receive(I2S_HandleTypeDef *hi2s, uint16_t *pData, uint16_t Size, uint32_t Timeout);
+
+/* Non-Blocking mode: Interrupt */
+HAL_StatusTypeDef HAL_I2S_Transmit_IT(I2S_HandleTypeDef *hi2s, uint16_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_I2S_Receive_IT(I2S_HandleTypeDef *hi2s, uint16_t *pData, uint16_t Size);
+void HAL_I2S_IRQHandler(I2S_HandleTypeDef *hi2s);
+
+/* Non-Blocking mode: DMA */
+HAL_StatusTypeDef HAL_I2S_Transmit_DMA(I2S_HandleTypeDef *hi2s, uint16_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_I2S_Receive_DMA(I2S_HandleTypeDef *hi2s, uint16_t *pData, uint16_t Size);
+
+HAL_StatusTypeDef HAL_I2S_DMAPause(I2S_HandleTypeDef *hi2s);
+HAL_StatusTypeDef HAL_I2S_DMAResume(I2S_HandleTypeDef *hi2s);
+HAL_StatusTypeDef HAL_I2S_DMAStop(I2S_HandleTypeDef *hi2s);
+
+/* Callbacks used in non blocking modes (Interrupt and DMA) *******************/
+void HAL_I2S_TxHalfCpltCallback(I2S_HandleTypeDef *hi2s);
+void HAL_I2S_TxCpltCallback(I2S_HandleTypeDef *hi2s);
+void HAL_I2S_RxHalfCpltCallback(I2S_HandleTypeDef *hi2s);
+void HAL_I2S_RxCpltCallback(I2S_HandleTypeDef *hi2s);
+void HAL_I2S_ErrorCallback(I2S_HandleTypeDef *hi2s);
+/**
+  * @}
+  */
+
+/** @addtogroup I2S_Exported_Functions_Group3
+  * @{
+  */
+/* Peripheral Control and State functions  ************************************/
+HAL_I2S_StateTypeDef HAL_I2S_GetState(I2S_HandleTypeDef *hi2s);
+uint32_t HAL_I2S_GetError(I2S_HandleTypeDef *hi2s);
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Private types -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private constants ---------------------------------------------------------*/
+/* Private macros ------------------------------------------------------------*/
+/** @defgroup I2S_Private_Macros I2S Private Macros
+  * @{
+  */
+
+/** @brief  Check whether the specified SPI flag is set or not.
+  * @param  __SR__  copy of I2S SR register.
+  * @param  __FLAG__ specifies the flag to check.
+  *         This parameter can be one of the following values:
+  *            @arg I2S_FLAG_RXNE: Receive buffer not empty flag
+  *            @arg I2S_FLAG_TXE: Transmit buffer empty flag
+  *            @arg I2S_FLAG_UDR: Underrun error flag
+  *            @arg I2S_FLAG_OVR: Overrun flag
+  *            @arg I2S_FLAG_CHSIDE: Channel side flag
+  *            @arg I2S_FLAG_BSY: Busy flag
+  * @retval SET or RESET.
+  */
+#define I2S_CHECK_FLAG(__SR__, __FLAG__)         ((((__SR__)\
+                                                    & ((__FLAG__) & I2S_FLAG_MASK)) == ((__FLAG__) & I2S_FLAG_MASK)) ? SET : RESET)
+
+/** @brief  Check whether the specified SPI Interrupt is set or not.
+  * @param  __CR2__  copy of I2S CR2 register.
+  * @param  __INTERRUPT__ specifies the SPI interrupt source to check.
+  *         This parameter can be one of the following values:
+  *            @arg I2S_IT_TXE: Tx buffer empty interrupt enable
+  *            @arg I2S_IT_RXNE: RX buffer not empty interrupt enable
+  *            @arg I2S_IT_ERR: Error interrupt enable
+  * @retval SET or RESET.
+  */
+#define I2S_CHECK_IT_SOURCE(__CR2__, __INTERRUPT__)      ((((__CR2__)\
+                                                            & (__INTERRUPT__)) == (__INTERRUPT__)) ? SET : RESET)
+
+/** @brief  Checks if I2S Mode parameter is in allowed range.
+  * @param  __MODE__ specifies the I2S Mode.
+  *         This parameter can be a value of @ref I2S_Mode
+  * @retval None
+  */
+#define IS_I2S_MODE(__MODE__) (((__MODE__) == I2S_MODE_SLAVE_TX)  || \
+                               ((__MODE__) == I2S_MODE_SLAVE_RX)  || \
+                               ((__MODE__) == I2S_MODE_MASTER_TX) || \
+                               ((__MODE__) == I2S_MODE_MASTER_RX))
+
+#define IS_I2S_STANDARD(__STANDARD__) (((__STANDARD__) == I2S_STANDARD_PHILIPS)   || \
+                                       ((__STANDARD__) == I2S_STANDARD_MSB)       || \
+                                       ((__STANDARD__) == I2S_STANDARD_LSB)       || \
+                                       ((__STANDARD__) == I2S_STANDARD_PCM_SHORT) || \
+                                       ((__STANDARD__) == I2S_STANDARD_PCM_LONG))
+
+#define IS_I2S_DATA_FORMAT(__FORMAT__) (((__FORMAT__) == I2S_DATAFORMAT_16B)          || \
+                                        ((__FORMAT__) == I2S_DATAFORMAT_16B_EXTENDED) || \
+                                        ((__FORMAT__) == I2S_DATAFORMAT_24B)          || \
+                                        ((__FORMAT__) == I2S_DATAFORMAT_32B))
+
+#define IS_I2S_MCLK_OUTPUT(__OUTPUT__) (((__OUTPUT__) == I2S_MCLKOUTPUT_ENABLE) || \
+                                        ((__OUTPUT__) == I2S_MCLKOUTPUT_DISABLE))
+
+#define IS_I2S_AUDIO_FREQ(__FREQ__) ((((__FREQ__) >= I2S_AUDIOFREQ_8K)    && \
+                                      ((__FREQ__) <= I2S_AUDIOFREQ_192K)) || \
+                                     ((__FREQ__) == I2S_AUDIOFREQ_DEFAULT))
+
+/** @brief  Checks if I2S Serial clock steady state parameter is in allowed range.
+  * @param  __CPOL__ specifies the I2S serial clock steady state.
+  *         This parameter can be a value of @ref I2S_Clock_Polarity
+  * @retval None
+  */
+#define IS_I2S_CPOL(__CPOL__) (((__CPOL__) == I2S_CPOL_LOW) || \
+                               ((__CPOL__) == I2S_CPOL_HIGH))
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+#endif /* SPI_I2S_SUPPORT */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* STM32F1xx_HAL_I2S_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_irda.h

@@ -0,0 +1,672 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_hal_irda.h
+  * @author  MCD Application Team
+  * @brief   Header file of IRDA HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F1xx_HAL_IRDA_H
+#define __STM32F1xx_HAL_IRDA_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_hal_def.h"
+
+/** @addtogroup STM32F1xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup IRDA
+  * @{
+  */
+
+/* Exported types ------------------------------------------------------------*/
+/** @defgroup IRDA_Exported_Types IRDA Exported Types
+  * @{
+  */
+/**
+  * @brief IRDA Init Structure definition
+  */
+typedef struct
+{
+  uint32_t BaudRate;                  /*!< This member configures the IRDA communication baud rate.
+                                           The baud rate is computed using the following formula:
+                                           - IntegerDivider = ((PCLKx) / (16 * (hirda->Init.BaudRate)))
+                                           - FractionalDivider = ((IntegerDivider - ((uint32_t) IntegerDivider)) * 16) + 0.5 */
+
+  uint32_t WordLength;                /*!< Specifies the number of data bits transmitted or received in a frame.
+                                           This parameter can be a value of @ref IRDA_Word_Length */
+
+  uint32_t Parity;                    /*!< Specifies the parity mode.
+                                           This parameter can be a value of @ref IRDA_Parity
+                                           @note When parity is enabled, the computed parity is inserted
+                                                 at the MSB position of the transmitted data (9th bit when
+                                                 the word length is set to 9 data bits; 8th bit when the
+                                                 word length is set to 8 data bits). */
+
+  uint32_t Mode;                      /*!< Specifies whether the Receive or Transmit mode is enabled or disabled.
+                                           This parameter can be a value of @ref IRDA_Mode */
+
+  uint8_t  Prescaler;                 /*!< Specifies the Prescaler value to be programmed
+                                           in the IrDA low-power Baud Register, for defining pulse width on which
+                                           burst acceptance/rejection will be decided. This value is used as divisor
+                                           of system clock to achieve required pulse width. */
+
+  uint32_t IrDAMode;                  /*!< Specifies the IrDA mode
+                                           This parameter can be a value of @ref IRDA_Low_Power */
+} IRDA_InitTypeDef;
+
+/**
+  * @brief HAL IRDA State structures definition
+  * @note  HAL IRDA State value is a combination of 2 different substates: gState and RxState.
+  *        - gState contains IRDA state information related to global Handle management
+  *          and also information related to Tx operations.
+  *          gState value coding follow below described bitmap :
+  *          b7-b6  Error information
+  *             00 : No Error
+  *             01 : (Not Used)
+  *             10 : Timeout
+  *             11 : Error
+  *          b5     IP initialisation status
+  *             0  : Reset (IP not initialized)
+  *             1  : Init done (IP initialized. HAL IRDA Init function already called)
+  *          b4-b3  (not used)
+  *             xx : Should be set to 00
+  *          b2     Intrinsic process state
+  *             0  : Ready
+  *             1  : Busy (IP busy with some configuration or internal operations)
+  *          b1     (not used)
+  *             x  : Should be set to 0
+  *          b0     Tx state
+  *             0  : Ready (no Tx operation ongoing)
+  *             1  : Busy (Tx operation ongoing)
+  *        - RxState contains information related to Rx operations.
+  *          RxState value coding follow below described bitmap :
+  *          b7-b6  (not used)
+  *             xx : Should be set to 00
+  *          b5     IP initialisation status
+  *             0  : Reset (IP not initialized)
+  *             1  : Init done (IP initialized)
+  *          b4-b2  (not used)
+  *            xxx : Should be set to 000
+  *          b1     Rx state
+  *             0  : Ready (no Rx operation ongoing)
+  *             1  : Busy (Rx operation ongoing)
+  *          b0     (not used)
+  *             x  : Should be set to 0.
+  */
+typedef enum
+{
+  HAL_IRDA_STATE_RESET             = 0x00U,    /*!< Peripheral is not yet Initialized
+                                                   Value is allowed for gState and RxState */
+  HAL_IRDA_STATE_READY             = 0x20U,    /*!< Peripheral Initialized and ready for use
+                                                   Value is allowed for gState and RxState */
+  HAL_IRDA_STATE_BUSY              = 0x24U,    /*!< An internal process is ongoing
+                                                   Value is allowed for gState only */
+  HAL_IRDA_STATE_BUSY_TX           = 0x21U,    /*!< Data Transmission process is ongoing
+                                                   Value is allowed for gState only */
+  HAL_IRDA_STATE_BUSY_RX           = 0x22U,    /*!< Data Reception process is ongoing
+                                                   Value is allowed for RxState only */
+  HAL_IRDA_STATE_BUSY_TX_RX        = 0x23U,    /*!< Data Transmission and Reception process is ongoing
+                                                   Not to be used for neither gState nor RxState.
+                                                   Value is result of combination (Or) between gState and RxState values */
+  HAL_IRDA_STATE_TIMEOUT           = 0xA0U,    /*!< Timeout state
+                                                   Value is allowed for gState only */
+  HAL_IRDA_STATE_ERROR             = 0xE0U     /*!< Error
+                                                   Value is allowed for gState only */
+} HAL_IRDA_StateTypeDef;
+
+/**
+  * @brief IRDA handle Structure definition
+  */
+#if (USE_HAL_IRDA_REGISTER_CALLBACKS == 1)
+typedef struct __IRDA_HandleTypeDef
+#else
+typedef struct
+#endif  /* USE_HAL_IRDA_REGISTER_CALLBACKS */
+{
+  USART_TypeDef               *Instance;        /*!<  USART registers base address       */
+
+  IRDA_InitTypeDef            Init;             /*!<  IRDA communication parameters      */
+
+  uint8_t                     *pTxBuffPtr;      /*!<  Pointer to IRDA Tx transfer Buffer */
+
+  uint16_t                    TxXferSize;       /*!<  IRDA Tx Transfer size              */
+
+  __IO uint16_t               TxXferCount;      /*!<  IRDA Tx Transfer Counter           */
+
+  uint8_t                     *pRxBuffPtr;      /*!<  Pointer to IRDA Rx transfer Buffer */
+
+  uint16_t                    RxXferSize;       /*!<  IRDA Rx Transfer size              */
+
+  __IO uint16_t               RxXferCount;      /*!<  IRDA Rx Transfer Counter           */
+
+  DMA_HandleTypeDef           *hdmatx;          /*!<  IRDA Tx DMA Handle parameters      */
+
+  DMA_HandleTypeDef           *hdmarx;          /*!<  IRDA Rx DMA Handle parameters      */
+
+  HAL_LockTypeDef             Lock;             /*!<  Locking object                     */
+
+  __IO HAL_IRDA_StateTypeDef  gState;           /*!<  IRDA state information related to global Handle management
+                                                   and also related to Tx operations.
+                                                   This parameter can be a value of @ref HAL_IRDA_StateTypeDef */
+
+  __IO HAL_IRDA_StateTypeDef  RxState;          /*!<  IRDA state information related to Rx operations.
+                                                   This parameter can be a value of @ref HAL_IRDA_StateTypeDef */
+
+  __IO uint32_t               ErrorCode;        /*!< IRDA Error code                    */
+
+#if (USE_HAL_IRDA_REGISTER_CALLBACKS == 1)
+  void (* TxHalfCpltCallback)(struct __IRDA_HandleTypeDef *hirda);        /*!< IRDA Tx Half Complete Callback        */
+
+  void (* TxCpltCallback)(struct __IRDA_HandleTypeDef *hirda);            /*!< IRDA Tx Complete Callback             */
+
+  void (* RxHalfCpltCallback)(struct __IRDA_HandleTypeDef *hirda);        /*!< IRDA Rx Half Complete Callback        */
+
+  void (* RxCpltCallback)(struct __IRDA_HandleTypeDef *hirda);            /*!< IRDA Rx Complete Callback             */
+
+  void (* ErrorCallback)(struct __IRDA_HandleTypeDef *hirda);             /*!< IRDA Error Callback                   */
+
+  void (* AbortCpltCallback)(struct __IRDA_HandleTypeDef *hirda);         /*!< IRDA Abort Complete Callback          */
+
+  void (* AbortTransmitCpltCallback)(struct __IRDA_HandleTypeDef *hirda); /*!< IRDA Abort Transmit Complete Callback */
+
+  void (* AbortReceiveCpltCallback)(struct __IRDA_HandleTypeDef *hirda);  /*!< IRDA Abort Receive Complete Callback  */
+
+
+  void (* MspInitCallback)(struct __IRDA_HandleTypeDef *hirda);           /*!< IRDA Msp Init callback                */
+
+  void (* MspDeInitCallback)(struct __IRDA_HandleTypeDef *hirda);         /*!< IRDA Msp DeInit callback              */
+#endif  /* USE_HAL_IRDA_REGISTER_CALLBACKS */
+
+} IRDA_HandleTypeDef;
+
+#if (USE_HAL_IRDA_REGISTER_CALLBACKS == 1)
+/**
+  * @brief  HAL IRDA Callback ID enumeration definition
+  */
+typedef enum
+{
+  HAL_IRDA_TX_HALFCOMPLETE_CB_ID         = 0x00U,    /*!< IRDA Tx Half Complete Callback ID        */
+  HAL_IRDA_TX_COMPLETE_CB_ID             = 0x01U,    /*!< IRDA Tx Complete Callback ID             */
+  HAL_IRDA_RX_HALFCOMPLETE_CB_ID         = 0x02U,    /*!< IRDA Rx Half Complete Callback ID        */
+  HAL_IRDA_RX_COMPLETE_CB_ID             = 0x03U,    /*!< IRDA Rx Complete Callback ID             */
+  HAL_IRDA_ERROR_CB_ID                   = 0x04U,    /*!< IRDA Error Callback ID                   */
+  HAL_IRDA_ABORT_COMPLETE_CB_ID          = 0x05U,    /*!< IRDA Abort Complete Callback ID          */
+  HAL_IRDA_ABORT_TRANSMIT_COMPLETE_CB_ID = 0x06U,    /*!< IRDA Abort Transmit Complete Callback ID */
+  HAL_IRDA_ABORT_RECEIVE_COMPLETE_CB_ID  = 0x07U,    /*!< IRDA Abort Receive Complete Callback ID  */
+
+  HAL_IRDA_MSPINIT_CB_ID                 = 0x08U,    /*!< IRDA MspInit callback ID                 */
+  HAL_IRDA_MSPDEINIT_CB_ID               = 0x09U     /*!< IRDA MspDeInit callback ID               */
+
+} HAL_IRDA_CallbackIDTypeDef;
+
+/**
+  * @brief  HAL IRDA Callback pointer definition
+  */
+typedef  void (*pIRDA_CallbackTypeDef)(IRDA_HandleTypeDef *hirda);  /*!< pointer to an IRDA callback function */
+
+#endif /* USE_HAL_IRDA_REGISTER_CALLBACKS */
+
+/**
+  * @}
+  */
+
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup IRDA_Exported_Constants IRDA Exported constants
+  * @{
+  */
+/** @defgroup IRDA_Error_Code IRDA Error Code
+  * @{
+  */
+#define HAL_IRDA_ERROR_NONE        0x00000000U   /*!< No error            */
+#define HAL_IRDA_ERROR_PE          0x00000001U   /*!< Parity error        */
+#define HAL_IRDA_ERROR_NE          0x00000002U   /*!< Noise error         */
+#define HAL_IRDA_ERROR_FE          0x00000004U   /*!< Frame error         */
+#define HAL_IRDA_ERROR_ORE         0x00000008U   /*!< Overrun error       */
+#define HAL_IRDA_ERROR_DMA         0x00000010U   /*!< DMA transfer error  */
+#if (USE_HAL_IRDA_REGISTER_CALLBACKS == 1)
+#define HAL_IRDA_ERROR_INVALID_CALLBACK   ((uint32_t)0x00000020U)   /*!< Invalid Callback error  */
+#endif /* USE_HAL_IRDA_REGISTER_CALLBACKS */
+/**
+  * @}
+  */
+
+/** @defgroup IRDA_Word_Length IRDA Word Length
+  * @{
+  */
+#define IRDA_WORDLENGTH_8B         0x00000000U
+#define IRDA_WORDLENGTH_9B         ((uint32_t)USART_CR1_M)
+/**
+  * @}
+  */
+
+/** @defgroup IRDA_Parity  IRDA Parity
+  * @{
+  */
+#define IRDA_PARITY_NONE           0x00000000U
+#define IRDA_PARITY_EVEN           ((uint32_t)USART_CR1_PCE)
+#define IRDA_PARITY_ODD            ((uint32_t)(USART_CR1_PCE | USART_CR1_PS))
+/**
+  * @}
+  */
+
+/** @defgroup IRDA_Mode IRDA Transfer Mode
+  * @{
+  */
+#define IRDA_MODE_RX               ((uint32_t)USART_CR1_RE)
+#define IRDA_MODE_TX               ((uint32_t)USART_CR1_TE)
+#define IRDA_MODE_TX_RX            ((uint32_t)(USART_CR1_TE |USART_CR1_RE))
+/**
+  * @}
+  */
+
+/** @defgroup IRDA_Low_Power IRDA Low Power
+  * @{
+  */
+#define IRDA_POWERMODE_LOWPOWER    ((uint32_t)USART_CR3_IRLP)
+#define IRDA_POWERMODE_NORMAL      0x00000000U
+/**
+  * @}
+  */
+
+/** @defgroup IRDA_Flags IRDA Flags
+  *        Elements values convention: 0xXXXX
+  *           - 0xXXXX  : Flag mask in the SR register
+  * @{
+  */
+#define IRDA_FLAG_TXE              ((uint32_t)USART_SR_TXE)
+#define IRDA_FLAG_TC               ((uint32_t)USART_SR_TC)
+#define IRDA_FLAG_RXNE             ((uint32_t)USART_SR_RXNE)
+#define IRDA_FLAG_IDLE             ((uint32_t)USART_SR_IDLE)
+#define IRDA_FLAG_ORE              ((uint32_t)USART_SR_ORE)
+#define IRDA_FLAG_NE               ((uint32_t)USART_SR_NE)
+#define IRDA_FLAG_FE               ((uint32_t)USART_SR_FE)
+#define IRDA_FLAG_PE               ((uint32_t)USART_SR_PE)
+/**
+  * @}
+  */
+
+/** @defgroup IRDA_Interrupt_definition IRDA Interrupt Definitions
+  *        Elements values convention: 0xY000XXXX
+  *           - XXXX  : Interrupt mask in the XX register
+  *           - Y  : Interrupt source register (2bits)
+  *                 - 01: CR1 register
+  *                 - 10: CR2 register
+  *                 - 11: CR3 register
+  * @{
+  */
+#define IRDA_IT_PE                 ((uint32_t)(IRDA_CR1_REG_INDEX << 28U | USART_CR1_PEIE))
+#define IRDA_IT_TXE                ((uint32_t)(IRDA_CR1_REG_INDEX << 28U | USART_CR1_TXEIE))
+#define IRDA_IT_TC                 ((uint32_t)(IRDA_CR1_REG_INDEX << 28U | USART_CR1_TCIE))
+#define IRDA_IT_RXNE               ((uint32_t)(IRDA_CR1_REG_INDEX << 28U | USART_CR1_RXNEIE))
+#define IRDA_IT_IDLE               ((uint32_t)(IRDA_CR1_REG_INDEX << 28U | USART_CR1_IDLEIE))
+
+#define IRDA_IT_LBD                ((uint32_t)(IRDA_CR2_REG_INDEX << 28U | USART_CR2_LBDIE))
+
+#define IRDA_IT_CTS                ((uint32_t)(IRDA_CR3_REG_INDEX << 28U | USART_CR3_CTSIE))
+#define IRDA_IT_ERR                ((uint32_t)(IRDA_CR3_REG_INDEX << 28U | USART_CR3_EIE))
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Exported macro ------------------------------------------------------------*/
+/** @defgroup IRDA_Exported_Macros IRDA Exported Macros
+  * @{
+  */
+
+/** @brief Reset IRDA handle gstate & RxState
+  * @param  __HANDLE__ specifies the IRDA Handle.
+  *         IRDA Handle selects the USARTx or UARTy peripheral
+  *         (USART,UART availability and x,y values depending on device).
+  * @retval None
+  */
+#if USE_HAL_IRDA_REGISTER_CALLBACKS == 1
+#define __HAL_IRDA_RESET_HANDLE_STATE(__HANDLE__)  do{                                                   \
+                                                       (__HANDLE__)->gState = HAL_IRDA_STATE_RESET;      \
+                                                       (__HANDLE__)->RxState = HAL_IRDA_STATE_RESET;     \
+                                                       (__HANDLE__)->MspInitCallback = NULL;             \
+                                                       (__HANDLE__)->MspDeInitCallback = NULL;           \
+                                                     } while(0U)
+#else
+#define __HAL_IRDA_RESET_HANDLE_STATE(__HANDLE__)  do{                                                   \
+                                                       (__HANDLE__)->gState = HAL_IRDA_STATE_RESET;      \
+                                                       (__HANDLE__)->RxState = HAL_IRDA_STATE_RESET;     \
+                                                     } while(0U)
+#endif /*USE_HAL_IRDA_REGISTER_CALLBACKS  */
+
+/** @brief  Flush the IRDA DR register
+  * @param  __HANDLE__ specifies the IRDA Handle.
+  *         IRDA Handle selects the USARTx or UARTy peripheral
+  *         (USART,UART availability and x,y values depending on device).
+  * @retval None
+  */
+#define __HAL_IRDA_FLUSH_DRREGISTER(__HANDLE__) ((__HANDLE__)->Instance->DR)
+
+/** @brief  Check whether the specified IRDA flag is set or not.
+  * @param  __HANDLE__ specifies the IRDA Handle.
+  *         IRDA Handle selects the USARTx or UARTy peripheral
+  *         (USART,UART availability and x,y values depending on device).
+  * @param  __FLAG__ specifies the flag to check.
+  *        This parameter can be one of the following values:
+  *            @arg IRDA_FLAG_TXE:  Transmit data register empty flag
+  *            @arg IRDA_FLAG_TC:   Transmission Complete flag
+  *            @arg IRDA_FLAG_RXNE: Receive data register not empty flag
+  *            @arg IRDA_FLAG_IDLE: Idle Line detection flag
+  *            @arg IRDA_FLAG_ORE:  OverRun Error flag
+  *            @arg IRDA_FLAG_NE:   Noise Error flag
+  *            @arg IRDA_FLAG_FE:   Framing Error flag
+  *            @arg IRDA_FLAG_PE:   Parity Error flag
+  * @retval The new state of __FLAG__ (TRUE or FALSE).
+  */
+#define __HAL_IRDA_GET_FLAG(__HANDLE__, __FLAG__) (((__HANDLE__)->Instance->SR & (__FLAG__)) == (__FLAG__))
+
+/** @brief  Clear the specified IRDA pending flag.
+  * @param  __HANDLE__ specifies the IRDA Handle.
+  *         IRDA Handle selects the USARTx or UARTy peripheral
+  *         (USART,UART availability and x,y values depending on device).
+  * @param  __FLAG__ specifies the flag to check.
+  *          This parameter can be any combination of the following values:
+  *            @arg IRDA_FLAG_TC:   Transmission Complete flag.
+  *            @arg IRDA_FLAG_RXNE: Receive data register not empty flag.
+  *
+  * @note   PE (Parity error), FE (Framing error), NE (Noise error), ORE (OverRun
+  *          error) and IDLE (Idle line detected) flags are cleared by software
+  *          sequence: a read operation to USART_SR register followed by a read
+  *          operation to USART_DR register.
+  * @note   RXNE flag can be also cleared by a read to the USART_DR register.
+  * @note   TC flag can be also cleared by software sequence: a read operation to
+  *          USART_SR register followed by a write operation to USART_DR register.
+  * @note   TXE flag is cleared only by a write to the USART_DR register.
+  * @retval None
+  */
+#define __HAL_IRDA_CLEAR_FLAG(__HANDLE__, __FLAG__) ((__HANDLE__)->Instance->SR = ~(__FLAG__))
+
+/** @brief  Clear the IRDA PE pending flag.
+  * @param  __HANDLE__ specifies the IRDA Handle.
+  *         IRDA Handle selects the USARTx or UARTy peripheral
+  *         (USART,UART availability and x,y values depending on device).
+  * @retval None
+  */
+#define __HAL_IRDA_CLEAR_PEFLAG(__HANDLE__)     \
+  do{                                           \
+    __IO uint32_t tmpreg = 0x00U;               \
+    tmpreg = (__HANDLE__)->Instance->SR;        \
+    tmpreg = (__HANDLE__)->Instance->DR;        \
+    UNUSED(tmpreg);                             \
+  } while(0U)
+
+/** @brief  Clear the IRDA FE pending flag.
+  * @param  __HANDLE__ specifies the IRDA Handle.
+  *         IRDA Handle selects the USARTx or UARTy peripheral
+  *         (USART,UART availability and x,y values depending on device).
+  * @retval None
+  */
+#define __HAL_IRDA_CLEAR_FEFLAG(__HANDLE__) __HAL_IRDA_CLEAR_PEFLAG(__HANDLE__)
+
+/** @brief  Clear the IRDA NE pending flag.
+  * @param  __HANDLE__ specifies the IRDA Handle.
+  *         IRDA Handle selects the USARTx or UARTy peripheral
+  *         (USART,UART availability and x,y values depending on device).
+  * @retval None
+  */
+#define __HAL_IRDA_CLEAR_NEFLAG(__HANDLE__) __HAL_IRDA_CLEAR_PEFLAG(__HANDLE__)
+
+/** @brief  Clear the IRDA ORE pending flag.
+  * @param  __HANDLE__ specifies the IRDA Handle.
+  *         IRDA Handle selects the USARTx or UARTy peripheral
+  *         (USART,UART availability and x,y values depending on device).
+  * @retval None
+  */
+#define __HAL_IRDA_CLEAR_OREFLAG(__HANDLE__) __HAL_IRDA_CLEAR_PEFLAG(__HANDLE__)
+
+/** @brief  Clear the IRDA IDLE pending flag.
+  * @param  __HANDLE__ specifies the IRDA Handle.
+  *         IRDA Handle selects the USARTx or UARTy peripheral
+  *         (USART,UART availability and x,y values depending on device).
+  * @retval None
+  */
+#define __HAL_IRDA_CLEAR_IDLEFLAG(__HANDLE__) __HAL_IRDA_CLEAR_PEFLAG(__HANDLE__)
+
+/** @brief  Enable the specified IRDA interrupt.
+  * @param  __HANDLE__ specifies the IRDA Handle.
+  *         IRDA Handle selects the USARTx or UARTy peripheral
+  *         (USART,UART availability and x,y values depending on device).
+  * @param  __INTERRUPT__ specifies the IRDA interrupt source to enable.
+  *          This parameter can be one of the following values:
+  *            @arg IRDA_IT_TXE:  Transmit Data Register empty interrupt
+  *            @arg IRDA_IT_TC:   Transmission complete interrupt
+  *            @arg IRDA_IT_RXNE: Receive Data register not empty interrupt
+  *            @arg IRDA_IT_IDLE: Idle line detection interrupt
+  *            @arg IRDA_IT_PE:   Parity Error interrupt
+  *            @arg IRDA_IT_ERR:  Error interrupt(Frame error, noise error, overrun error)
+  * @retval None
+  */
+#define __HAL_IRDA_ENABLE_IT(__HANDLE__, __INTERRUPT__)   ((((__INTERRUPT__) >> 28U) == IRDA_CR1_REG_INDEX)? ((__HANDLE__)->Instance->CR1 |= ((__INTERRUPT__) & IRDA_IT_MASK)): \
+                                                           (((__INTERRUPT__) >> 28U) == IRDA_CR2_REG_INDEX)? ((__HANDLE__)->Instance->CR2 |=  ((__INTERRUPT__) & IRDA_IT_MASK)): \
+                                                            ((__HANDLE__)->Instance->CR3 |= ((__INTERRUPT__) & IRDA_IT_MASK)))
+/** @brief  Disable the specified IRDA interrupt.
+  * @param  __HANDLE__ specifies the IRDA Handle.
+  *         IRDA Handle selects the USARTx or UARTy peripheral
+  *         (USART,UART availability and x,y values depending on device).
+  * @param  __INTERRUPT__ specifies the IRDA interrupt source to disable.
+  *          This parameter can be one of the following values:
+  *            @arg IRDA_IT_TXE:  Transmit Data Register empty interrupt
+  *            @arg IRDA_IT_TC:   Transmission complete interrupt
+  *            @arg IRDA_IT_RXNE: Receive Data register not empty interrupt
+  *            @arg IRDA_IT_IDLE: Idle line detection interrupt
+  *            @arg IRDA_IT_PE:   Parity Error interrupt
+  *            @arg IRDA_IT_ERR:  Error interrupt(Frame error, noise error, overrun error)
+  * @retval None
+  */
+#define __HAL_IRDA_DISABLE_IT(__HANDLE__, __INTERRUPT__)  ((((__INTERRUPT__) >> 28U) == IRDA_CR1_REG_INDEX)? ((__HANDLE__)->Instance->CR1 &= ~((__INTERRUPT__) & IRDA_IT_MASK)): \
+                                                           (((__INTERRUPT__) >> 28U) == IRDA_CR2_REG_INDEX)? ((__HANDLE__)->Instance->CR2 &= ~((__INTERRUPT__) & IRDA_IT_MASK)): \
+                                                           ((__HANDLE__)->Instance->CR3 &= ~ ((__INTERRUPT__) & IRDA_IT_MASK)))
+
+/** @brief  Check whether the specified IRDA interrupt has occurred or not.
+  * @param  __HANDLE__ specifies the IRDA Handle.
+  *         IRDA Handle selects the USARTx or UARTy peripheral
+  *         (USART,UART availability and x,y values depending on device).
+  * @param  __IT__ specifies the IRDA interrupt source to check.
+  *          This parameter can be one of the following values:
+  *            @arg IRDA_IT_TXE: Transmit Data Register empty interrupt
+  *            @arg IRDA_IT_TC:  Transmission complete interrupt
+  *            @arg IRDA_IT_RXNE: Receive Data register not empty interrupt
+  *            @arg IRDA_IT_IDLE: Idle line detection interrupt
+  *            @arg IRDA_IT_ERR: Error interrupt
+  *            @arg IRDA_IT_PE: Parity Error interrupt
+  * @retval The new state of __IT__ (TRUE or FALSE).
+  */
+#define __HAL_IRDA_GET_IT_SOURCE(__HANDLE__, __IT__) (((((__IT__) >> 28U) == IRDA_CR1_REG_INDEX)? (__HANDLE__)->Instance->CR1:(((((uint32_t)(__IT__)) >> 28U) == IRDA_CR2_REG_INDEX)? \
+                                                      (__HANDLE__)->Instance->CR2 : (__HANDLE__)->Instance->CR3)) & (((uint32_t)(__IT__)) & IRDA_IT_MASK))
+
+/** @brief  Enable UART/USART associated to IRDA Handle
+  * @param  __HANDLE__ specifies the IRDA Handle.
+  *         IRDA Handle selects the USARTx or UARTy peripheral
+  *         (USART,UART availability and x,y values depending on device).
+  * @retval None
+  */
+#define __HAL_IRDA_ENABLE(__HANDLE__)                   (SET_BIT((__HANDLE__)->Instance->CR1, USART_CR1_UE))
+
+/** @brief  Disable UART/USART associated to IRDA Handle
+  * @param  __HANDLE__ specifies the IRDA Handle.
+  *         IRDA Handle selects the USARTx or UARTy peripheral
+  *         (USART,UART availability and x,y values depending on device).
+  * @retval None
+  */
+#define __HAL_IRDA_DISABLE(__HANDLE__)                  (CLEAR_BIT((__HANDLE__)->Instance->CR1, USART_CR1_UE))
+
+/**
+  * @}
+  */
+
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup IRDA_Exported_Functions
+  * @{
+  */
+
+/** @addtogroup IRDA_Exported_Functions_Group1
+  * @{
+  */
+/* Initialization/de-initialization functions  **********************************/
+HAL_StatusTypeDef HAL_IRDA_Init(IRDA_HandleTypeDef *hirda);
+HAL_StatusTypeDef HAL_IRDA_DeInit(IRDA_HandleTypeDef *hirda);
+void HAL_IRDA_MspInit(IRDA_HandleTypeDef *hirda);
+void HAL_IRDA_MspDeInit(IRDA_HandleTypeDef *hirda);
+
+#if (USE_HAL_IRDA_REGISTER_CALLBACKS == 1)
+/* Callbacks Register/UnRegister functions  ***********************************/
+HAL_StatusTypeDef HAL_IRDA_RegisterCallback(IRDA_HandleTypeDef *hirda, HAL_IRDA_CallbackIDTypeDef CallbackID, pIRDA_CallbackTypeDef pCallback);
+HAL_StatusTypeDef HAL_IRDA_UnRegisterCallback(IRDA_HandleTypeDef *hirda, HAL_IRDA_CallbackIDTypeDef CallbackID);
+#endif /* USE_HAL_IRDA_REGISTER_CALLBACKS */
+
+/**
+  * @}
+  */
+
+/** @addtogroup IRDA_Exported_Functions_Group2
+  * @{
+  */
+/* IO operation functions *******************************************************/
+HAL_StatusTypeDef HAL_IRDA_Transmit(IRDA_HandleTypeDef *hirda, uint8_t *pData, uint16_t Size, uint32_t Timeout);
+HAL_StatusTypeDef HAL_IRDA_Receive(IRDA_HandleTypeDef *hirda, uint8_t *pData, uint16_t Size, uint32_t Timeout);
+HAL_StatusTypeDef HAL_IRDA_Transmit_IT(IRDA_HandleTypeDef *hirda, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_IRDA_Receive_IT(IRDA_HandleTypeDef *hirda, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_IRDA_Transmit_DMA(IRDA_HandleTypeDef *hirda, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_IRDA_Receive_DMA(IRDA_HandleTypeDef *hirda, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_IRDA_DMAPause(IRDA_HandleTypeDef *hirda);
+HAL_StatusTypeDef HAL_IRDA_DMAResume(IRDA_HandleTypeDef *hirda);
+HAL_StatusTypeDef HAL_IRDA_DMAStop(IRDA_HandleTypeDef *hirda);
+/* Transfer Abort functions */
+HAL_StatusTypeDef HAL_IRDA_Abort(IRDA_HandleTypeDef *hirda);
+HAL_StatusTypeDef HAL_IRDA_AbortTransmit(IRDA_HandleTypeDef *hirda);
+HAL_StatusTypeDef HAL_IRDA_AbortReceive(IRDA_HandleTypeDef *hirda);
+HAL_StatusTypeDef HAL_IRDA_Abort_IT(IRDA_HandleTypeDef *hirda);
+HAL_StatusTypeDef HAL_IRDA_AbortTransmit_IT(IRDA_HandleTypeDef *hirda);
+HAL_StatusTypeDef HAL_IRDA_AbortReceive_IT(IRDA_HandleTypeDef *hirda);
+
+void HAL_IRDA_IRQHandler(IRDA_HandleTypeDef *hirda);
+void HAL_IRDA_TxCpltCallback(IRDA_HandleTypeDef *hirda);
+void HAL_IRDA_RxCpltCallback(IRDA_HandleTypeDef *hirda);
+void HAL_IRDA_TxHalfCpltCallback(IRDA_HandleTypeDef *hirda);
+void HAL_IRDA_RxHalfCpltCallback(IRDA_HandleTypeDef *hirda);
+void HAL_IRDA_ErrorCallback(IRDA_HandleTypeDef *hirda);
+void HAL_IRDA_AbortCpltCallback(IRDA_HandleTypeDef *hirda);
+void HAL_IRDA_AbortTransmitCpltCallback(IRDA_HandleTypeDef *hirda);
+void HAL_IRDA_AbortReceiveCpltCallback(IRDA_HandleTypeDef *hirda);
+/**
+  * @}
+  */
+
+/** @addtogroup IRDA_Exported_Functions_Group3
+  * @{
+  */
+/* Peripheral State functions  **************************************************/
+HAL_IRDA_StateTypeDef HAL_IRDA_GetState(IRDA_HandleTypeDef *hirda);
+uint32_t HAL_IRDA_GetError(IRDA_HandleTypeDef *hirda);
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Private types -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private constants ---------------------------------------------------------*/
+/** @defgroup IRDA_Private_Constants IRDA Private Constants
+  * @{
+  */
+
+/** @brief IRDA interruptions flag mask
+  *
+  */
+#define IRDA_IT_MASK  ((uint32_t) USART_CR1_PEIE | USART_CR1_TXEIE | USART_CR1_TCIE | USART_CR1_RXNEIE | \
+                                  USART_CR1_IDLEIE | USART_CR2_LBDIE | USART_CR3_CTSIE | USART_CR3_EIE )
+
+#define IRDA_CR1_REG_INDEX         1U
+#define IRDA_CR2_REG_INDEX         2U
+#define IRDA_CR3_REG_INDEX         3U
+/**
+  * @}
+  */
+
+/* Private macros --------------------------------------------------------*/
+/** @defgroup IRDA_Private_Macros   IRDA Private Macros
+  * @{
+  */
+#define IS_IRDA_WORD_LENGTH(LENGTH)   (((LENGTH) == IRDA_WORDLENGTH_8B) || \
+                                       ((LENGTH) == IRDA_WORDLENGTH_9B))
+
+#define IS_IRDA_PARITY(PARITY)        (((PARITY) == IRDA_PARITY_NONE) || \
+                                       ((PARITY) == IRDA_PARITY_EVEN) || \
+                                       ((PARITY) == IRDA_PARITY_ODD))
+
+#define IS_IRDA_MODE(MODE)            ((((MODE) & 0x0000FFF3U) == 0x00U) && ((MODE) != 0x00000000U))
+
+#define IS_IRDA_POWERMODE(MODE)       (((MODE) == IRDA_POWERMODE_LOWPOWER) || \
+                                       ((MODE) == IRDA_POWERMODE_NORMAL))
+
+#define IS_IRDA_BAUDRATE(BAUDRATE)    ((BAUDRATE) < 115201U)
+
+#define IRDA_DIV(_PCLK_, _BAUD_)      (((_PCLK_)*25U)/(4U*(_BAUD_)))
+
+#define IRDA_DIVMANT(_PCLK_, _BAUD_)  (IRDA_DIV((_PCLK_), (_BAUD_))/100U)
+
+#define IRDA_DIVFRAQ(_PCLK_, _BAUD_)  ((((IRDA_DIV((_PCLK_), (_BAUD_)) - (IRDA_DIVMANT((_PCLK_), (_BAUD_)) * 100U)) * 16U) + 50U) / 100U)
+
+/* UART BRR = mantissa + overflow + fraction
+            = (UART DIVMANT << 4) + (UART DIVFRAQ & 0xF0) + (UART DIVFRAQ & 0x0FU) */
+#define IRDA_BRR(_PCLK_, _BAUD_)      (((IRDA_DIVMANT((_PCLK_), (_BAUD_)) << 4U) + \
+                                        (IRDA_DIVFRAQ((_PCLK_), (_BAUD_)) & 0xF0U)) + \
+                                        (IRDA_DIVFRAQ((_PCLK_), (_BAUD_)) & 0x0FU))
+
+/**
+  * @}
+  */
+
+/* Private functions ---------------------------------------------------------*/
+/** @defgroup IRDA_Private_Functions IRDA Private Functions
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F1xx_HAL_IRDA_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_iwdg.h

@@ -0,0 +1,223 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_hal_iwdg.h
+  * @author  MCD Application Team
+  * @brief   Header file of IWDG HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef STM32F1xx_HAL_IWDG_H
+#define STM32F1xx_HAL_IWDG_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_hal_def.h"
+
+/** @addtogroup STM32F1xx_HAL_Driver
+  * @{
+  */
+
+/** @defgroup IWDG IWDG
+  * @{
+  */
+
+/* Exported types ------------------------------------------------------------*/
+/** @defgroup IWDG_Exported_Types IWDG Exported Types
+  * @{
+  */
+
+/**
+  * @brief  IWDG Init structure definition
+  */
+typedef struct
+{
+  uint32_t Prescaler;  /*!< Select the prescaler of the IWDG.
+                            This parameter can be a value of @ref IWDG_Prescaler */
+
+  uint32_t Reload;     /*!< Specifies the IWDG down-counter reload value.
+                            This parameter must be a number between Min_Data = 0 and Max_Data = 0x0FFF */
+
+} IWDG_InitTypeDef;
+
+/**
+  * @brief  IWDG Handle Structure definition
+  */
+typedef struct
+{
+  IWDG_TypeDef                 *Instance;  /*!< Register base address    */
+
+  IWDG_InitTypeDef             Init;       /*!< IWDG required parameters */
+} IWDG_HandleTypeDef;
+
+
+/**
+  * @}
+  */
+
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup IWDG_Exported_Constants IWDG Exported Constants
+  * @{
+  */
+
+/** @defgroup IWDG_Prescaler IWDG Prescaler
+  * @{
+  */
+#define IWDG_PRESCALER_4                0x00000000u                                     /*!< IWDG prescaler set to 4   */
+#define IWDG_PRESCALER_8                IWDG_PR_PR_0                                    /*!< IWDG prescaler set to 8   */
+#define IWDG_PRESCALER_16               IWDG_PR_PR_1                                    /*!< IWDG prescaler set to 16  */
+#define IWDG_PRESCALER_32               (IWDG_PR_PR_1 | IWDG_PR_PR_0)                   /*!< IWDG prescaler set to 32  */
+#define IWDG_PRESCALER_64               IWDG_PR_PR_2                                    /*!< IWDG prescaler set to 64  */
+#define IWDG_PRESCALER_128              (IWDG_PR_PR_2 | IWDG_PR_PR_0)                   /*!< IWDG prescaler set to 128 */
+#define IWDG_PRESCALER_256              (IWDG_PR_PR_2 | IWDG_PR_PR_1)                   /*!< IWDG prescaler set to 256 */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Exported macros -----------------------------------------------------------*/
+/** @defgroup IWDG_Exported_Macros IWDG Exported Macros
+  * @{
+  */
+
+/**
+  * @brief  Enable the IWDG peripheral.
+  * @param  __HANDLE__  IWDG handle
+  * @retval None
+  */
+#define __HAL_IWDG_START(__HANDLE__)                WRITE_REG((__HANDLE__)->Instance->KR, IWDG_KEY_ENABLE)
+
+/**
+  * @brief  Reload IWDG counter with value defined in the reload register
+  *         (write access to IWDG_PR and IWDG_RLR registers disabled).
+  * @param  __HANDLE__  IWDG handle
+  * @retval None
+  */
+#define __HAL_IWDG_RELOAD_COUNTER(__HANDLE__)       WRITE_REG((__HANDLE__)->Instance->KR, IWDG_KEY_RELOAD)
+
+/**
+  * @}
+  */
+
+/* Exported functions --------------------------------------------------------*/
+/** @defgroup IWDG_Exported_Functions  IWDG Exported Functions
+  * @{
+  */
+
+/** @defgroup IWDG_Exported_Functions_Group1 Initialization and Start functions
+  * @{
+  */
+/* Initialization/Start functions  ********************************************/
+HAL_StatusTypeDef     HAL_IWDG_Init(IWDG_HandleTypeDef *hiwdg);
+/**
+  * @}
+  */
+
+/** @defgroup IWDG_Exported_Functions_Group2 IO operation functions
+  * @{
+  */
+/* I/O operation functions ****************************************************/
+HAL_StatusTypeDef     HAL_IWDG_Refresh(IWDG_HandleTypeDef *hiwdg);
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Private constants ---------------------------------------------------------*/
+/** @defgroup IWDG_Private_Constants IWDG Private Constants
+  * @{
+  */
+
+/**
+  * @brief  IWDG Key Register BitMask
+  */
+#define IWDG_KEY_RELOAD                 0x0000AAAAu  /*!< IWDG Reload Counter Enable   */
+#define IWDG_KEY_ENABLE                 0x0000CCCCu  /*!< IWDG Peripheral Enable       */
+#define IWDG_KEY_WRITE_ACCESS_ENABLE    0x00005555u  /*!< IWDG KR Write Access Enable  */
+#define IWDG_KEY_WRITE_ACCESS_DISABLE   0x00000000u  /*!< IWDG KR Write Access Disable */
+
+/**
+  * @}
+  */
+
+/* Private macros ------------------------------------------------------------*/
+/** @defgroup IWDG_Private_Macros IWDG Private Macros
+  * @{
+  */
+
+/**
+  * @brief  Enable write access to IWDG_PR and IWDG_RLR registers.
+  * @param  __HANDLE__  IWDG handle
+  * @retval None
+  */
+#define IWDG_ENABLE_WRITE_ACCESS(__HANDLE__)  WRITE_REG((__HANDLE__)->Instance->KR, IWDG_KEY_WRITE_ACCESS_ENABLE)
+
+/**
+  * @brief  Disable write access to IWDG_PR and IWDG_RLR registers.
+  * @param  __HANDLE__  IWDG handle
+  * @retval None
+  */
+#define IWDG_DISABLE_WRITE_ACCESS(__HANDLE__) WRITE_REG((__HANDLE__)->Instance->KR, IWDG_KEY_WRITE_ACCESS_DISABLE)
+
+/**
+  * @brief  Check IWDG prescaler value.
+  * @param  __PRESCALER__  IWDG prescaler value
+  * @retval None
+  */
+#define IS_IWDG_PRESCALER(__PRESCALER__)      (((__PRESCALER__) == IWDG_PRESCALER_4)  || \
+                                               ((__PRESCALER__) == IWDG_PRESCALER_8)  || \
+                                               ((__PRESCALER__) == IWDG_PRESCALER_16) || \
+                                               ((__PRESCALER__) == IWDG_PRESCALER_32) || \
+                                               ((__PRESCALER__) == IWDG_PRESCALER_64) || \
+                                               ((__PRESCALER__) == IWDG_PRESCALER_128)|| \
+                                               ((__PRESCALER__) == IWDG_PRESCALER_256))
+
+/**
+  * @brief  Check IWDG reload value.
+  * @param  __RELOAD__  IWDG reload value
+  * @retval None
+  */
+#define IS_IWDG_RELOAD(__RELOAD__)            ((__RELOAD__) <= IWDG_RLR_RL)
+
+
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* STM32F1xx_HAL_IWDG_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_mmc.h

@@ -0,0 +1,745 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_hal_mmc.h
+  * @author  MCD Application Team
+  * @brief   Header file of MMC HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2018 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                       opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */ 
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef STM32F1xx_HAL_MMC_H
+#define STM32F1xx_HAL_MMC_H
+
+#if defined(SDIO)
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_ll_sdmmc.h"
+
+/** @addtogroup STM32F1xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup MMC
+  * @{
+  */ 
+
+/* Exported types ------------------------------------------------------------*/ 
+/** @defgroup MMC_Exported_Types MMC Exported Types
+  * @{
+  */
+
+/** @defgroup MMC_Exported_Types_Group1 MMC State enumeration structure
+  * @{
+  */   
+typedef enum
+{
+  HAL_MMC_STATE_RESET                  = 0x00000000U,  /*!< MMC not yet initialized or disabled  */
+  HAL_MMC_STATE_READY                  = 0x00000001U,  /*!< MMC initialized and ready for use    */
+  HAL_MMC_STATE_TIMEOUT                = 0x00000002U,  /*!< MMC Timeout state                    */
+  HAL_MMC_STATE_BUSY                   = 0x00000003U,  /*!< MMC process ongoing                  */
+  HAL_MMC_STATE_PROGRAMMING            = 0x00000004U,  /*!< MMC Programming State                */
+  HAL_MMC_STATE_RECEIVING              = 0x00000005U,  /*!< MMC Receinving State                 */
+  HAL_MMC_STATE_TRANSFER               = 0x00000006U,  /*!< MMC Transfer State                  */
+  HAL_MMC_STATE_ERROR                  = 0x0000000FU   /*!< MMC is in error state                */
+}HAL_MMC_StateTypeDef;
+/** 
+  * @}
+  */
+
+/** @defgroup MMC_Exported_Types_Group2 MMC Card State enumeration structure
+  * @{
+  */   
+typedef uint32_t HAL_MMC_CardStateTypeDef;
+
+#define HAL_MMC_CARD_READY          0x00000001U  /*!< Card state is ready                     */
+#define HAL_MMC_CARD_IDENTIFICATION 0x00000002U  /*!< Card is in identification state         */
+#define HAL_MMC_CARD_STANDBY        0x00000003U  /*!< Card is in standby state                */
+#define HAL_MMC_CARD_TRANSFER       0x00000004U  /*!< Card is in transfer state               */
+#define HAL_MMC_CARD_SENDING        0x00000005U  /*!< Card is sending an operation            */
+#define HAL_MMC_CARD_RECEIVING      0x00000006U  /*!< Card is receiving operation information */
+#define HAL_MMC_CARD_PROGRAMMING    0x00000007U  /*!< Card is in programming state            */
+#define HAL_MMC_CARD_DISCONNECTED   0x00000008U  /*!< Card is disconnected                    */
+#define HAL_MMC_CARD_ERROR          0x000000FFU  /*!< Card response Error                     */
+/** 
+  * @}
+  */
+
+/** @defgroup MMC_Exported_Types_Group3 MMC Handle Structure definition   
+  * @{
+  */
+#define MMC_InitTypeDef      SDIO_InitTypeDef 
+#define MMC_TypeDef          SDIO_TypeDef
+
+/** 
+  * @brief  MMC Card Information Structure definition
+  */ 
+typedef struct
+{
+  uint32_t CardType;                     /*!< Specifies the card Type                         */
+
+  uint32_t Class;                        /*!< Specifies the class of the card class           */
+
+  uint32_t RelCardAdd;                   /*!< Specifies the Relative Card Address             */
+  
+  uint32_t BlockNbr;                     /*!< Specifies the Card Capacity in blocks           */
+
+  uint32_t BlockSize;                    /*!< Specifies one block size in bytes               */
+  
+  uint32_t LogBlockNbr;                  /*!< Specifies the Card logical Capacity in blocks   */
+
+  uint32_t LogBlockSize;                 /*!< Specifies logical block size in bytes           */
+
+}HAL_MMC_CardInfoTypeDef;
+
+/** 
+  * @brief  MMC handle Structure definition
+  */ 
+#if defined (USE_HAL_MMC_REGISTER_CALLBACKS) && (USE_HAL_MMC_REGISTER_CALLBACKS == 1U)
+typedef struct __MMC_HandleTypeDef
+#else
+typedef struct
+#endif /* USE_HAL_MMC_REGISTER_CALLBACKS */
+{
+  MMC_TypeDef                  *Instance;        /*!< MMC registers base address           */
+  
+  MMC_InitTypeDef              Init;             /*!< MMC required parameters              */
+  
+  HAL_LockTypeDef              Lock;             /*!< MMC locking object                   */
+  
+  uint8_t                      *pTxBuffPtr;      /*!< Pointer to MMC Tx transfer Buffer    */
+
+  uint32_t                     TxXferSize;       /*!< MMC Tx Transfer size                 */
+
+  uint8_t                      *pRxBuffPtr;      /*!< Pointer to MMC Rx transfer Buffer    */
+
+  uint32_t                     RxXferSize;       /*!< MMC Rx Transfer size                 */
+  
+  __IO uint32_t                Context;          /*!< MMC transfer context                 */
+ 
+  __IO HAL_MMC_StateTypeDef    State;            /*!< MMC card State                       */
+  
+  __IO uint32_t                ErrorCode;        /*!< MMC Card Error codes                 */  
+ 
+  DMA_HandleTypeDef            *hdmarx;          /*!< MMC Rx DMA handle parameters         */
+  
+  DMA_HandleTypeDef            *hdmatx;          /*!< MMC Tx DMA handle parameters         */
+  
+  HAL_MMC_CardInfoTypeDef      MmcCard;          /*!< MMC Card information                 */
+
+  uint32_t                     CSD[4U];          /*!< MMC card specific data table         */
+  
+  uint32_t                     CID[4U];          /*!< MMC card identification number table */
+  
+#if defined (USE_HAL_MMC_REGISTER_CALLBACKS) && (USE_HAL_MMC_REGISTER_CALLBACKS == 1U)
+  void (* TxCpltCallback)                 (struct __MMC_HandleTypeDef *hmmc);
+  void (* RxCpltCallback)                 (struct __MMC_HandleTypeDef *hmmc);
+  void (* ErrorCallback)                  (struct __MMC_HandleTypeDef *hmmc);
+  void (* AbortCpltCallback)              (struct __MMC_HandleTypeDef *hmmc);
+
+  void (* MspInitCallback)                (struct __MMC_HandleTypeDef *hmmc);
+  void (* MspDeInitCallback)              (struct __MMC_HandleTypeDef *hmmc);
+#endif  
+}MMC_HandleTypeDef;
+
+/** 
+  * @}
+  */
+
+/** @defgroup MMC_Exported_Types_Group4 Card Specific Data: CSD Register 
+  * @{
+  */
+typedef struct
+{
+  __IO uint8_t  CSDStruct;            /*!< CSD structure                         */
+  __IO uint8_t  SysSpecVersion;       /*!< System specification version          */
+  __IO uint8_t  Reserved1;            /*!< Reserved                              */
+  __IO uint8_t  TAAC;                 /*!< Data read access time 1               */
+  __IO uint8_t  NSAC;                 /*!< Data read access time 2 in CLK cycles */
+  __IO uint8_t  MaxBusClkFrec;        /*!< Max. bus clock frequency              */
+  __IO uint16_t CardComdClasses;      /*!< Card command classes                  */
+  __IO uint8_t  RdBlockLen;           /*!< Max. read data block length           */
+  __IO uint8_t  PartBlockRead;        /*!< Partial blocks for read allowed       */
+  __IO uint8_t  WrBlockMisalign;      /*!< Write block misalignment              */
+  __IO uint8_t  RdBlockMisalign;      /*!< Read block misalignment               */
+  __IO uint8_t  DSRImpl;              /*!< DSR implemented                       */
+  __IO uint8_t  Reserved2;            /*!< Reserved                              */
+  __IO uint32_t DeviceSize;           /*!< Device Size                           */
+  __IO uint8_t  MaxRdCurrentVDDMin;   /*!< Max. read current @ VDD min           */
+  __IO uint8_t  MaxRdCurrentVDDMax;   /*!< Max. read current @ VDD max           */
+  __IO uint8_t  MaxWrCurrentVDDMin;   /*!< Max. write current @ VDD min          */
+  __IO uint8_t  MaxWrCurrentVDDMax;   /*!< Max. write current @ VDD max          */
+  __IO uint8_t  DeviceSizeMul;        /*!< Device size multiplier                */
+  __IO uint8_t  EraseGrSize;          /*!< Erase group size                      */
+  __IO uint8_t  EraseGrMul;           /*!< Erase group size multiplier           */
+  __IO uint8_t  WrProtectGrSize;      /*!< Write protect group size              */
+  __IO uint8_t  WrProtectGrEnable;    /*!< Write protect group enable            */
+  __IO uint8_t  ManDeflECC;           /*!< Manufacturer default ECC              */
+  __IO uint8_t  WrSpeedFact;          /*!< Write speed factor                    */
+  __IO uint8_t  MaxWrBlockLen;        /*!< Max. write data block length          */
+  __IO uint8_t  WriteBlockPaPartial;  /*!< Partial blocks for write allowed      */
+  __IO uint8_t  Reserved3;            /*!< Reserved                              */
+  __IO uint8_t  ContentProtectAppli;  /*!< Content protection application        */
+  __IO uint8_t  FileFormatGroup;      /*!< File format group                     */
+  __IO uint8_t  CopyFlag;             /*!< Copy flag (OTP)                       */
+  __IO uint8_t  PermWrProtect;        /*!< Permanent write protection            */
+  __IO uint8_t  TempWrProtect;        /*!< Temporary write protection            */
+  __IO uint8_t  FileFormat;           /*!< File format                           */
+  __IO uint8_t  ECC;                  /*!< ECC code                              */
+  __IO uint8_t  CSD_CRC;              /*!< CSD CRC                               */
+  __IO uint8_t  Reserved4;            /*!< Always 1                              */
+  
+}HAL_MMC_CardCSDTypeDef;
+/** 
+  * @}
+  */
+
+/** @defgroup MMC_Exported_Types_Group5 Card Identification Data: CID Register
+  * @{
+  */
+typedef struct
+{
+  __IO uint8_t  ManufacturerID;  /*!< Manufacturer ID       */
+  __IO uint16_t OEM_AppliID;     /*!< OEM/Application ID    */
+  __IO uint32_t ProdName1;       /*!< Product Name part1    */
+  __IO uint8_t  ProdName2;       /*!< Product Name part2    */
+  __IO uint8_t  ProdRev;         /*!< Product Revision      */
+  __IO uint32_t ProdSN;          /*!< Product Serial Number */
+  __IO uint8_t  Reserved1;       /*!< Reserved1             */
+  __IO uint16_t ManufactDate;    /*!< Manufacturing Date    */
+  __IO uint8_t  CID_CRC;         /*!< CID CRC               */
+  __IO uint8_t  Reserved2;       /*!< Always 1              */
+
+}HAL_MMC_CardCIDTypeDef;
+/** 
+  * @}
+  */
+
+#if defined (USE_HAL_MMC_REGISTER_CALLBACKS) && (USE_HAL_MMC_REGISTER_CALLBACKS == 1U)
+/** @defgroup MMC_Exported_Types_Group6 MMC Callback ID enumeration definition 
+  * @{
+  */
+typedef enum
+{
+  HAL_MMC_TX_CPLT_CB_ID                 = 0x00U,  /*!< MMC Tx Complete Callback ID                     */
+  HAL_MMC_RX_CPLT_CB_ID                 = 0x01U,  /*!< MMC Rx Complete Callback ID                     */
+  HAL_MMC_ERROR_CB_ID                   = 0x02U,  /*!< MMC Error Callback ID                           */
+  HAL_MMC_ABORT_CB_ID                   = 0x03U,  /*!< MMC Abort Callback ID                           */
+
+  HAL_MMC_MSP_INIT_CB_ID                = 0x10U,  /*!< MMC MspInit Callback ID                         */
+  HAL_MMC_MSP_DEINIT_CB_ID              = 0x11U   /*!< MMC MspDeInit Callback ID                       */
+}HAL_MMC_CallbackIDTypeDef;
+/** 
+  * @}
+  */
+
+/** @defgroup MMC_Exported_Types_Group7 MMC Callback pointer definition 
+  * @{
+  */
+typedef void (*pMMC_CallbackTypeDef)           (MMC_HandleTypeDef *hmmc);
+/** 
+  * @}
+  */
+#endif
+/** 
+  * @}
+  */
+
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup MMC_Exported_Constants Exported Constants
+  * @{
+  */
+
+#define MMC_BLOCKSIZE              512U  /*!< Block size is 512 bytes */
+
+/** @defgroup MMC_Exported_Constansts_Group1 MMC Error status enumeration Structure definition 
+  * @{
+  */  
+#define HAL_MMC_ERROR_NONE                     SDMMC_ERROR_NONE                    /*!< No error                                                      */
+#define HAL_MMC_ERROR_CMD_CRC_FAIL             SDMMC_ERROR_CMD_CRC_FAIL            /*!< Command response received (but CRC check failed)              */
+#define HAL_MMC_ERROR_DATA_CRC_FAIL            SDMMC_ERROR_DATA_CRC_FAIL           /*!< Data block sent/received (CRC check failed)                   */
+#define HAL_MMC_ERROR_CMD_RSP_TIMEOUT          SDMMC_ERROR_CMD_RSP_TIMEOUT         /*!< Command response timeout                                      */
+#define HAL_MMC_ERROR_DATA_TIMEOUT             SDMMC_ERROR_DATA_TIMEOUT            /*!< Data timeout                                                  */
+#define HAL_MMC_ERROR_TX_UNDERRUN              SDMMC_ERROR_TX_UNDERRUN             /*!< Transmit FIFO underrun                                        */
+#define HAL_MMC_ERROR_RX_OVERRUN               SDMMC_ERROR_RX_OVERRUN              /*!< Receive FIFO overrun                                          */
+#define HAL_MMC_ERROR_ADDR_MISALIGNED          SDMMC_ERROR_ADDR_MISALIGNED         /*!< Misaligned address                                            */
+#define HAL_MMC_ERROR_BLOCK_LEN_ERR            SDMMC_ERROR_BLOCK_LEN_ERR           /*!< Transferred block length is not allowed for the card or the 
+                                                                                       number of transferred bytes does not match the block length   */
+#define HAL_MMC_ERROR_ERASE_SEQ_ERR            SDMMC_ERROR_ERASE_SEQ_ERR           /*!< An error in the sequence of erase command occurs              */
+#define HAL_MMC_ERROR_BAD_ERASE_PARAM          SDMMC_ERROR_BAD_ERASE_PARAM         /*!< An invalid selection for erase groups                         */
+#define HAL_MMC_ERROR_WRITE_PROT_VIOLATION     SDMMC_ERROR_WRITE_PROT_VIOLATION    /*!< Attempt to program a write protect block                      */
+#define HAL_MMC_ERROR_LOCK_UNLOCK_FAILED       SDMMC_ERROR_LOCK_UNLOCK_FAILED      /*!< Sequence or password error has been detected in unlock 
+                                                                                       command or if there was an attempt to access a locked card    */
+#define HAL_MMC_ERROR_COM_CRC_FAILED           SDMMC_ERROR_COM_CRC_FAILED          /*!< CRC check of the previous command failed                      */
+#define HAL_MMC_ERROR_ILLEGAL_CMD              SDMMC_ERROR_ILLEGAL_CMD             /*!< Command is not legal for the card state                       */
+#define HAL_MMC_ERROR_CARD_ECC_FAILED          SDMMC_ERROR_CARD_ECC_FAILED         /*!< Card internal ECC was applied but failed to correct the data  */
+#define HAL_MMC_ERROR_CC_ERR                   SDMMC_ERROR_CC_ERR                  /*!< Internal card controller error                                */
+#define HAL_MMC_ERROR_GENERAL_UNKNOWN_ERR      SDMMC_ERROR_GENERAL_UNKNOWN_ERR     /*!< General or unknown error                                      */
+#define HAL_MMC_ERROR_STREAM_READ_UNDERRUN     SDMMC_ERROR_STREAM_READ_UNDERRUN    /*!< The card could not sustain data reading in stream rmode       */
+#define HAL_MMC_ERROR_STREAM_WRITE_OVERRUN     SDMMC_ERROR_STREAM_WRITE_OVERRUN    /*!< The card could not sustain data programming in stream mode    */
+#define HAL_MMC_ERROR_CID_CSD_OVERWRITE        SDMMC_ERROR_CID_CSD_OVERWRITE       /*!< CID/CSD overwrite error                                       */
+#define HAL_MMC_ERROR_WP_ERASE_SKIP            SDMMC_ERROR_WP_ERASE_SKIP           /*!< Only partial address space was erased                         */
+#define HAL_MMC_ERROR_CARD_ECC_DISABLED        SDMMC_ERROR_CARD_ECC_DISABLED       /*!< Command has been executed without using internal ECC          */
+#define HAL_MMC_ERROR_ERASE_RESET              SDMMC_ERROR_ERASE_RESET             /*!< Erase sequence was cleared before executing because an out 
+                                                                                       of erase sequence command was received                        */
+#define HAL_MMC_ERROR_AKE_SEQ_ERR              SDMMC_ERROR_AKE_SEQ_ERR             /*!< Error in sequence of authentication                           */
+#define HAL_MMC_ERROR_INVALID_VOLTRANGE        SDMMC_ERROR_INVALID_VOLTRANGE       /*!< Error in case of invalid voltage range                        */        
+#define HAL_MMC_ERROR_ADDR_OUT_OF_RANGE        SDMMC_ERROR_ADDR_OUT_OF_RANGE       /*!< Error when addressed block is out of range                    */        
+#define HAL_MMC_ERROR_REQUEST_NOT_APPLICABLE   SDMMC_ERROR_REQUEST_NOT_APPLICABLE  /*!< Error when command request is not applicable                  */  
+#define HAL_MMC_ERROR_PARAM                    SDMMC_ERROR_INVALID_PARAMETER       /*!< the used parameter is not valid                               */  
+#define HAL_MMC_ERROR_UNSUPPORTED_FEATURE      SDMMC_ERROR_UNSUPPORTED_FEATURE     /*!< Error when feature is not insupported                         */
+#define HAL_MMC_ERROR_BUSY                     SDMMC_ERROR_BUSY                    /*!< Error when transfer process is busy                           */ 
+#define HAL_MMC_ERROR_DMA                      SDMMC_ERROR_DMA                     /*!< Error while DMA transfer                                      */
+#define HAL_MMC_ERROR_TIMEOUT                  SDMMC_ERROR_TIMEOUT                 /*!< Timeout error                                                 */
+                                                
+#if defined (USE_HAL_MMC_REGISTER_CALLBACKS) && (USE_HAL_MMC_REGISTER_CALLBACKS == 1U)
+#define HAL_MMC_ERROR_INVALID_CALLBACK         SDMMC_ERROR_INVALID_PARAMETER       /*!< Invalid callback error                                        */
+#endif
+/** 
+  * @}
+  */
+ 
+/** @defgroup MMC_Exported_Constansts_Group2 MMC context enumeration
+  * @{
+  */ 
+#define   MMC_CONTEXT_NONE                            0x00000000U   /*!< None                             */
+#define   MMC_CONTEXT_READ_SINGLE_BLOCK               0x00000001U   /*!< Read single block operation      */
+#define   MMC_CONTEXT_READ_MULTIPLE_BLOCK             0x00000002U   /*!< Read multiple blocks operation   */
+#define   MMC_CONTEXT_WRITE_SINGLE_BLOCK              0x00000010U   /*!< Write single block operation     */
+#define   MMC_CONTEXT_WRITE_MULTIPLE_BLOCK            0x00000020U   /*!< Write multiple blocks operation  */
+#define   MMC_CONTEXT_IT                              0x00000008U   /*!< Process in Interrupt mode        */
+#define   MMC_CONTEXT_DMA                             0x00000080U   /*!< Process in DMA mode              */
+
+/**
+  * @}
+  */
+
+/** @defgroup MMC_Exported_Constansts_Group3 MMC Voltage mode
+  * @{
+  */
+/** 
+  * @brief 
+  */
+#define MMC_HIGH_VOLTAGE_RANGE         0x80FF8000U  /*!< VALUE OF ARGUMENT            */
+#define MMC_DUAL_VOLTAGE_RANGE         0x80FF8080U  /*!< VALUE OF ARGUMENT            */
+#define eMMC_HIGH_VOLTAGE_RANGE        0xC0FF8000U  /*!< for eMMC > 2Gb sector mode   */
+#define eMMC_DUAL_VOLTAGE_RANGE        0xC0FF8080U  /*!< for eMMC > 2Gb sector mode   */
+#define MMC_INVALID_VOLTAGE_RANGE      0x0001FF01U 
+/**
+  * @}
+  */
+
+/** @defgroup MMC_Exported_Constansts_Group4 MMC Memory Cards
+  * @{
+  */
+#define  MMC_LOW_CAPACITY_CARD                0x00000000U    /*!< MMC Card Capacity <=2Gbytes   */
+#define  MMC_HIGH_CAPACITY_CARD               0x00000001U    /*!< MMC Card Capacity >2Gbytes and <2Tbytes   */
+
+/**
+  * @}
+  */
+      
+/**
+  * @}
+  */
+  
+/* Exported macro ------------------------------------------------------------*/
+/** @defgroup MMC_Exported_macros MMC Exported Macros
+ *  @brief macros to handle interrupts and specific clock configurations
+ * @{
+ */
+/** @brief Reset MMC handle state.
+  * @param  __HANDLE__ : MMC handle.
+  * @retval None
+  */
+#if defined (USE_HAL_MMC_REGISTER_CALLBACKS) && (USE_HAL_MMC_REGISTER_CALLBACKS == 1U)
+#define __HAL_MMC_RESET_HANDLE_STATE(__HANDLE__)           do {                                              \
+                                                               (__HANDLE__)->State = HAL_MMC_STATE_RESET; \
+                                                               (__HANDLE__)->MspInitCallback = NULL;       \
+                                                               (__HANDLE__)->MspDeInitCallback = NULL;     \
+                                                             } while(0)
+#else
+#define __HAL_MMC_RESET_HANDLE_STATE(__HANDLE__)           ((__HANDLE__)->State = HAL_MMC_STATE_RESET)
+#endif
+ 
+/**
+  * @brief  Enable the MMC device.
+  * @retval None
+  */ 
+#define __HAL_MMC_ENABLE(__HANDLE__) __SDIO_ENABLE((__HANDLE__)->Instance)
+
+/**
+  * @brief  Disable the MMC device.
+  * @retval None
+  */
+#define __HAL_MMC_DISABLE(__HANDLE__) __SDIO_DISABLE((__HANDLE__)->Instance)
+
+/**
+  * @brief  Enable the SDMMC DMA transfer.
+  * @retval None
+  */ 
+#define __HAL_MMC_DMA_ENABLE(__HANDLE__) __SDIO_DMA_ENABLE((__HANDLE__)->Instance)
+
+/**
+  * @brief  Disable the SDMMC DMA transfer.
+  * @retval None
+  */
+#define __HAL_MMC_DMA_DISABLE(__HANDLE__)  __SDIO_DMA_DISABLE((__HANDLE__)->Instance)
+ 
+/**
+  * @brief  Enable the MMC device interrupt.
+  * @param  __HANDLE__: MMC Handle  
+  * @param  __INTERRUPT__: specifies the SDMMC interrupt sources to be enabled.
+  *         This parameter can be one or a combination of the following values:
+  *            @arg SDIO_IT_CCRCFAIL: Command response received (CRC check failed) interrupt
+  *            @arg SDIO_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt
+  *            @arg SDIO_IT_CTIMEOUT: Command response timeout interrupt
+  *            @arg SDIO_IT_DTIMEOUT: Data timeout interrupt
+  *            @arg SDIO_IT_TXUNDERR: Transmit FIFO underrun error interrupt
+  *            @arg SDIO_IT_RXOVERR:  Received FIFO overrun error interrupt
+  *            @arg SDIO_IT_CMDREND:  Command response received (CRC check passed) interrupt
+  *            @arg SDIO_IT_CMDSENT:  Command sent (no response required) interrupt
+  *            @arg SDIO_IT_DATAEND:  Data end (data counter, DATACOUNT, is zero) interrupt
+  *            @arg SDIO_IT_DBCKEND:  Data block sent/received (CRC check passed) interrupt
+  *            @arg SDIO_IT_CMDACT:   Command transfer in progress interrupt
+  *            @arg SDIO_IT_TXACT:    Data transmit in progress interrupt
+  *            @arg SDIO_IT_RXACT:    Data receive in progress interrupt
+  *            @arg SDIO_IT_TXFIFOHE: Transmit FIFO Half Empty interrupt
+  *            @arg SDIO_IT_RXFIFOHF: Receive FIFO Half Full interrupt
+  *            @arg SDIO_IT_TXFIFOF:  Transmit FIFO full interrupt
+  *            @arg SDIO_IT_RXFIFOF:  Receive FIFO full interrupt
+  *            @arg SDIO_IT_TXFIFOE:  Transmit FIFO empty interrupt
+  *            @arg SDIO_IT_RXFIFOE:  Receive FIFO empty interrupt
+  *            @arg SDIO_IT_TXDAVL:   Data available in transmit FIFO interrupt
+  *            @arg SDIO_IT_RXDAVL:   Data available in receive FIFO interrupt
+  *            @arg SDIO_IT_SDIOIT:   SD I/O interrupt received interrupt
+  * @retval None
+  */
+#define __HAL_MMC_ENABLE_IT(__HANDLE__, __INTERRUPT__) __SDIO_ENABLE_IT((__HANDLE__)->Instance, (__INTERRUPT__))
+
+/**
+  * @brief  Disable the MMC device interrupt.
+  * @param  __HANDLE__: MMC Handle   
+  * @param  __INTERRUPT__: specifies the SDMMC interrupt sources to be disabled.
+  *          This parameter can be one or a combination of the following values:
+  *            @arg SDIO_IT_CCRCFAIL: Command response received (CRC check failed) interrupt
+  *            @arg SDIO_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt
+  *            @arg SDIO_IT_CTIMEOUT: Command response timeout interrupt
+  *            @arg SDIO_IT_DTIMEOUT: Data timeout interrupt
+  *            @arg SDIO_IT_TXUNDERR: Transmit FIFO underrun error interrupt
+  *            @arg SDIO_IT_RXOVERR:  Received FIFO overrun error interrupt
+  *            @arg SDIO_IT_CMDREND:  Command response received (CRC check passed) interrupt
+  *            @arg SDIO_IT_CMDSENT:  Command sent (no response required) interrupt
+  *            @arg SDIO_IT_DATAEND:  Data end (data counter, DATACOUNT, is zero) interrupt
+  *            @arg SDIO_IT_DBCKEND:  Data block sent/received (CRC check passed) interrupt
+  *            @arg SDIO_IT_CMDACT:   Command transfer in progress interrupt
+  *            @arg SDIO_IT_TXACT:    Data transmit in progress interrupt
+  *            @arg SDIO_IT_RXACT:    Data receive in progress interrupt
+  *            @arg SDIO_IT_TXFIFOHE: Transmit FIFO Half Empty interrupt
+  *            @arg SDIO_IT_RXFIFOHF: Receive FIFO Half Full interrupt
+  *            @arg SDIO_IT_TXFIFOF:  Transmit FIFO full interrupt
+  *            @arg SDIO_IT_RXFIFOF:  Receive FIFO full interrupt
+  *            @arg SDIO_IT_TXFIFOE:  Transmit FIFO empty interrupt
+  *            @arg SDIO_IT_RXFIFOE:  Receive FIFO empty interrupt
+  *            @arg SDIO_IT_TXDAVL:   Data available in transmit FIFO interrupt
+  *            @arg SDIO_IT_RXDAVL:   Data available in receive FIFO interrupt
+  *            @arg SDIO_IT_SDIOIT:   SD I/O interrupt received interrupt   
+  * @retval None
+  */
+#define __HAL_MMC_DISABLE_IT(__HANDLE__, __INTERRUPT__) __SDIO_DISABLE_IT((__HANDLE__)->Instance, (__INTERRUPT__))
+
+/**
+  * @brief  Check whether the specified MMC flag is set or not. 
+  * @param  __HANDLE__: MMC Handle   
+  * @param  __FLAG__: specifies the flag to check. 
+  *          This parameter can be one of the following values:
+  *            @arg SDIO_FLAG_CCRCFAIL: Command response received (CRC check failed)
+  *            @arg SDIO_FLAG_DCRCFAIL: Data block sent/received (CRC check failed)
+  *            @arg SDIO_FLAG_CTIMEOUT: Command response timeout
+  *            @arg SDIO_FLAG_DTIMEOUT: Data timeout
+  *            @arg SDIO_FLAG_TXUNDERR: Transmit FIFO underrun error
+  *            @arg SDIO_FLAG_RXOVERR:  Received FIFO overrun error
+  *            @arg SDIO_FLAG_CMDREND:  Command response received (CRC check passed)
+  *            @arg SDIO_FLAG_CMDSENT:  Command sent (no response required)
+  *            @arg SDIO_FLAG_DATAEND:  Data end (data counter, DATACOUNT, is zero)
+  *            @arg SDIO_FLAG_DBCKEND:  Data block sent/received (CRC check passed)
+  *            @arg SDIO_FLAG_CMDACT:   Command transfer in progress
+  *            @arg SDIO_FLAG_TXACT:    Data transmit in progress
+  *            @arg SDIO_FLAG_RXACT:    Data receive in progress
+  *            @arg SDIO_FLAG_TXFIFOHE: Transmit FIFO Half Empty
+  *            @arg SDIO_FLAG_RXFIFOHF: Receive FIFO Half Full
+  *            @arg SDIO_FLAG_TXFIFOF:  Transmit FIFO full
+  *            @arg SDIO_FLAG_RXFIFOF:  Receive FIFO full
+  *            @arg SDIO_FLAG_TXFIFOE:  Transmit FIFO empty
+  *            @arg SDIO_FLAG_RXFIFOE:  Receive FIFO empty
+  *            @arg SDIO_FLAG_TXDAVL:   Data available in transmit FIFO
+  *            @arg SDIO_FLAG_RXDAVL:   Data available in receive FIFO
+  *            @arg SDIO_FLAG_SDIOIT:   SD I/O interrupt received
+  * @retval The new state of MMC FLAG (SET or RESET).
+  */
+#define __HAL_MMC_GET_FLAG(__HANDLE__, __FLAG__) __SDIO_GET_FLAG((__HANDLE__)->Instance, (__FLAG__))
+
+/**
+  * @brief  Clear the MMC's pending flags.
+  * @param  __HANDLE__: MMC Handle  
+  * @param  __FLAG__: specifies the flag to clear.  
+  *          This parameter can be one or a combination of the following values:
+  *            @arg SDIO_FLAG_CCRCFAIL: Command response received (CRC check failed)
+  *            @arg SDIO_FLAG_DCRCFAIL: Data block sent/received (CRC check failed)
+  *            @arg SDIO_FLAG_CTIMEOUT: Command response timeout
+  *            @arg SDIO_FLAG_DTIMEOUT: Data timeout
+  *            @arg SDIO_FLAG_TXUNDERR: Transmit FIFO underrun error
+  *            @arg SDIO_FLAG_RXOVERR:  Received FIFO overrun error
+  *            @arg SDIO_FLAG_CMDREND:  Command response received (CRC check passed)
+  *            @arg SDIO_FLAG_CMDSENT:  Command sent (no response required)
+  *            @arg SDIO_FLAG_DATAEND:  Data end (data counter, DATACOUNT, is zero)
+  *            @arg SDIO_FLAG_DBCKEND:  Data block sent/received (CRC check passed)
+  *            @arg SDIO_FLAG_SDIOIT:   SD I/O interrupt received
+  * @retval None
+  */
+#define __HAL_MMC_CLEAR_FLAG(__HANDLE__, __FLAG__) __SDIO_CLEAR_FLAG((__HANDLE__)->Instance, (__FLAG__))
+
+/**
+  * @brief  Check whether the specified MMC interrupt has occurred or not.
+  * @param  __HANDLE__: MMC Handle   
+  * @param  __INTERRUPT__: specifies the SDMMC interrupt source to check. 
+  *          This parameter can be one of the following values:
+  *            @arg SDIO_IT_CCRCFAIL: Command response received (CRC check failed) interrupt
+  *            @arg SDIO_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt
+  *            @arg SDIO_IT_CTIMEOUT: Command response timeout interrupt
+  *            @arg SDIO_IT_DTIMEOUT: Data timeout interrupt
+  *            @arg SDIO_IT_TXUNDERR: Transmit FIFO underrun error interrupt
+  *            @arg SDIO_IT_RXOVERR:  Received FIFO overrun error interrupt
+  *            @arg SDIO_IT_CMDREND:  Command response received (CRC check passed) interrupt
+  *            @arg SDIO_IT_CMDSENT:  Command sent (no response required) interrupt
+  *            @arg SDIO_IT_DATAEND:  Data end (data counter, DATACOUNT, is zero) interrupt
+  *            @arg SDIO_IT_DBCKEND:  Data block sent/received (CRC check passed) interrupt
+  *            @arg SDIO_IT_CMDACT:   Command transfer in progress interrupt
+  *            @arg SDIO_IT_TXACT:    Data transmit in progress interrupt
+  *            @arg SDIO_IT_RXACT:    Data receive in progress interrupt
+  *            @arg SDIO_IT_TXFIFOHE: Transmit FIFO Half Empty interrupt
+  *            @arg SDIO_IT_RXFIFOHF: Receive FIFO Half Full interrupt
+  *            @arg SDIO_IT_TXFIFOF:  Transmit FIFO full interrupt
+  *            @arg SDIO_IT_RXFIFOF:  Receive FIFO full interrupt
+  *            @arg SDIO_IT_TXFIFOE:  Transmit FIFO empty interrupt
+  *            @arg SDIO_IT_RXFIFOE:  Receive FIFO empty interrupt
+  *            @arg SDIO_IT_TXDAVL:   Data available in transmit FIFO interrupt
+  *            @arg SDIO_IT_RXDAVL:   Data available in receive FIFO interrupt
+  *            @arg SDIO_IT_SDIOIT:   SD I/O interrupt received interrupt
+  * @retval The new state of MMC IT (SET or RESET).
+  */
+#define __HAL_MMC_GET_IT(__HANDLE__, __INTERRUPT__) __SDIO_GET_IT((__HANDLE__)->Instance, (__INTERRUPT__))
+
+/**
+  * @brief  Clear the MMC's interrupt pending bits.
+  * @param  __HANDLE__: MMC Handle
+  * @param  __INTERRUPT__: specifies the interrupt pending bit to clear. 
+  *          This parameter can be one or a combination of the following values:
+  *            @arg SDIO_IT_CCRCFAIL: Command response received (CRC check failed) interrupt
+  *            @arg SDIO_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt
+  *            @arg SDIO_IT_CTIMEOUT: Command response timeout interrupt
+  *            @arg SDIO_IT_DTIMEOUT: Data timeout interrupt
+  *            @arg SDIO_IT_TXUNDERR: Transmit FIFO underrun error interrupt
+  *            @arg SDIO_IT_RXOVERR:  Received FIFO overrun error interrupt
+  *            @arg SDIO_IT_CMDREND:  Command response received (CRC check passed) interrupt
+  *            @arg SDIO_IT_CMDSENT:  Command sent (no response required) interrupt
+  *            @arg SDIO_IT_DATAEND:  Data end (data counter, DATACOUNT, is zero) interrupt
+  *            @arg SDIO_IT_DBCKEND:    Data block sent/received (CRC check passed) interrupt
+  *            @arg SDIO_IT_TXFIFOHE:   Transmit FIFO Half Empty interrupt
+  *            @arg SDIO_IT_RXFIFOHF:   Receive FIFO Half Full interrupt
+  *            @arg SDIO_IT_RXFIFOF:    Receive FIFO full interrupt
+  *            @arg SDIO_IT_TXFIFOE:    Transmit FIFO empty interrupt
+  *            @arg SDIO_IT_SDIOIT:   SD I/O interrupt received interrupt
+  * @retval None
+  */
+#define __HAL_MMC_CLEAR_IT(__HANDLE__, __INTERRUPT__) __SDIO_CLEAR_IT((__HANDLE__)->Instance, (__INTERRUPT__))
+
+/**
+  * @}
+  */
+  
+/* Exported functions --------------------------------------------------------*/
+/** @defgroup MMC_Exported_Functions MMC Exported Functions
+  * @{
+  */
+  
+/** @defgroup MMC_Exported_Functions_Group1 Initialization and de-initialization functions
+  * @{
+  */
+HAL_StatusTypeDef HAL_MMC_Init(MMC_HandleTypeDef *hmmc);
+HAL_StatusTypeDef HAL_MMC_InitCard(MMC_HandleTypeDef *hmmc);
+HAL_StatusTypeDef HAL_MMC_DeInit (MMC_HandleTypeDef *hmmc);
+void HAL_MMC_MspInit(MMC_HandleTypeDef *hmmc);
+void HAL_MMC_MspDeInit(MMC_HandleTypeDef *hmmc);
+
+/**
+  * @}
+  */
+  
+/** @defgroup MMC_Exported_Functions_Group2 Input and Output operation functions
+  * @{
+  */
+/* Blocking mode: Polling */
+HAL_StatusTypeDef HAL_MMC_ReadBlocks(MMC_HandleTypeDef *hmmc, uint8_t *pData, uint32_t BlockAdd, uint32_t NumberOfBlocks, uint32_t Timeout);
+HAL_StatusTypeDef HAL_MMC_WriteBlocks(MMC_HandleTypeDef *hmmc, uint8_t *pData, uint32_t BlockAdd, uint32_t NumberOfBlocks, uint32_t Timeout);
+HAL_StatusTypeDef HAL_MMC_Erase(MMC_HandleTypeDef *hmmc, uint32_t BlockStartAdd, uint32_t BlockEndAdd);
+/* Non-Blocking mode: IT */
+HAL_StatusTypeDef HAL_MMC_ReadBlocks_IT(MMC_HandleTypeDef *hmmc, uint8_t *pData, uint32_t BlockAdd, uint32_t NumberOfBlocks);
+HAL_StatusTypeDef HAL_MMC_WriteBlocks_IT(MMC_HandleTypeDef *hmmc, uint8_t *pData, uint32_t BlockAdd, uint32_t NumberOfBlocks);
+/* Non-Blocking mode: DMA */
+HAL_StatusTypeDef HAL_MMC_ReadBlocks_DMA(MMC_HandleTypeDef *hmmc, uint8_t *pData, uint32_t BlockAdd, uint32_t NumberOfBlocks);
+HAL_StatusTypeDef HAL_MMC_WriteBlocks_DMA(MMC_HandleTypeDef *hmmc, uint8_t *pData, uint32_t BlockAdd, uint32_t NumberOfBlocks);
+
+void HAL_MMC_IRQHandler(MMC_HandleTypeDef *hmmc);
+
+/* Callback in non blocking modes (DMA) */
+void HAL_MMC_TxCpltCallback(MMC_HandleTypeDef *hmmc);
+void HAL_MMC_RxCpltCallback(MMC_HandleTypeDef *hmmc);
+void HAL_MMC_ErrorCallback(MMC_HandleTypeDef *hmmc);
+void HAL_MMC_AbortCallback(MMC_HandleTypeDef *hmmc);
+
+#if defined (USE_HAL_MMC_REGISTER_CALLBACKS) && (USE_HAL_MMC_REGISTER_CALLBACKS == 1U)
+/* MMC callback registering/unregistering */
+HAL_StatusTypeDef HAL_MMC_RegisterCallback  (MMC_HandleTypeDef *hmmc, HAL_MMC_CallbackIDTypeDef CallbackId, pMMC_CallbackTypeDef pCallback);
+HAL_StatusTypeDef HAL_MMC_UnRegisterCallback(MMC_HandleTypeDef *hmmc, HAL_MMC_CallbackIDTypeDef CallbackId);
+#endif
+/**
+  * @}
+  */
+  
+/** @defgroup MMC_Exported_Functions_Group3 Peripheral Control functions
+  * @{
+  */
+HAL_StatusTypeDef HAL_MMC_ConfigWideBusOperation(MMC_HandleTypeDef *hmmc, uint32_t WideMode);
+/**
+  * @}
+  */
+
+/** @defgroup MMC_Exported_Functions_Group4 MMC card related functions
+  * @{
+  */
+HAL_MMC_CardStateTypeDef HAL_MMC_GetCardState(MMC_HandleTypeDef *hmmc);
+HAL_StatusTypeDef HAL_MMC_GetCardCID(MMC_HandleTypeDef *hmmc, HAL_MMC_CardCIDTypeDef *pCID);
+HAL_StatusTypeDef HAL_MMC_GetCardCSD(MMC_HandleTypeDef *hmmc, HAL_MMC_CardCSDTypeDef *pCSD);
+HAL_StatusTypeDef HAL_MMC_GetCardInfo(MMC_HandleTypeDef *hmmc, HAL_MMC_CardInfoTypeDef *pCardInfo);
+/**
+  * @}
+  */
+
+/** @defgroup MMC_Exported_Functions_Group5 Peripheral State and Errors functions
+  * @{
+  */
+HAL_MMC_StateTypeDef HAL_MMC_GetState(MMC_HandleTypeDef *hmmc);
+uint32_t HAL_MMC_GetError(MMC_HandleTypeDef *hmmc);
+/**
+  * @}
+  */
+
+/** @defgroup MMC_Exported_Functions_Group6 Perioheral Abort management
+  * @{
+  */
+HAL_StatusTypeDef HAL_MMC_Abort(MMC_HandleTypeDef *hmmc);
+HAL_StatusTypeDef HAL_MMC_Abort_IT(MMC_HandleTypeDef *hmmc);
+/**
+  * @}
+  */
+    
+/* Private types -------------------------------------------------------------*/
+/** @defgroup MMC_Private_Types MMC Private Types
+  * @{
+  */
+
+/**
+  * @}
+  */ 
+
+/* Private defines -----------------------------------------------------------*/
+/** @defgroup MMC_Private_Defines MMC Private Defines
+  * @{
+  */
+
+/**
+  * @}
+  */ 
+          
+/* Private variables ---------------------------------------------------------*/
+/** @defgroup MMC_Private_Variables MMC Private Variables
+  * @{
+  */
+
+/**
+  * @}
+  */ 
+
+/* Private constants ---------------------------------------------------------*/
+/** @defgroup MMC_Private_Constants MMC Private Constants
+  * @{
+  */
+
+/**
+  * @}
+  */ 
+
+/* Private macros ------------------------------------------------------------*/
+/** @defgroup MMC_Private_Macros MMC Private Macros
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/* Private functions prototypes ----------------------------------------------*/
+/** @defgroup MMC_Private_Functions_Prototypes MMC Private Functions Prototypes
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/* Private functions ---------------------------------------------------------*/
+/** @defgroup MMC_Private_Functions MMC Private Functions
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+
+/**
+  * @}
+  */ 
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* SDIO */
+
+#endif /* STM32F1xx_HAL_MMC_H */ 
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_nand.h

@@ -0,0 +1,383 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_hal_nand.h
+  * @author  MCD Application Team
+  * @brief   Header file of NAND HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                       opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef STM32F1xx_HAL_NAND_H
+#define STM32F1xx_HAL_NAND_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+#if defined(FSMC_BANK3)
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_ll_fsmc.h"
+
+/** @addtogroup STM32F1xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup NAND
+  * @{
+  */
+
+/* Exported typedef ----------------------------------------------------------*/
+/* Exported types ------------------------------------------------------------*/
+/** @defgroup NAND_Exported_Types NAND Exported Types
+  * @{
+  */
+
+/**
+  * @brief  HAL NAND State structures definition
+  */
+typedef enum
+{
+  HAL_NAND_STATE_RESET     = 0x00U,  /*!< NAND not yet initialized or disabled */
+  HAL_NAND_STATE_READY     = 0x01U,  /*!< NAND initialized and ready for use   */
+  HAL_NAND_STATE_BUSY      = 0x02U,  /*!< NAND internal process is ongoing     */
+  HAL_NAND_STATE_ERROR     = 0x03U   /*!< NAND error state                     */
+} HAL_NAND_StateTypeDef;
+
+/**
+  * @brief  NAND Memory electronic signature Structure definition
+  */
+typedef struct
+{
+  /*<! NAND memory electronic signature maker and device IDs */
+
+  uint8_t Maker_Id;
+
+  uint8_t Device_Id;
+
+  uint8_t Third_Id;
+
+  uint8_t Fourth_Id;
+} NAND_IDTypeDef;
+
+/**
+  * @brief  NAND Memory address Structure definition
+  */
+typedef struct
+{
+  uint16_t Page;   /*!< NAND memory Page address  */
+
+  uint16_t Plane;   /*!< NAND memory Zone address  */
+
+  uint16_t Block;  /*!< NAND memory Block address */
+
+} NAND_AddressTypeDef;
+
+/**
+  * @brief  NAND Memory info Structure definition
+  */
+typedef struct
+{
+  uint32_t        PageSize;              /*!< NAND memory page (without spare area) size measured in bytes
+                                              for 8 bits addressing or words for 16 bits addressing             */
+
+  uint32_t        SpareAreaSize;         /*!< NAND memory spare area size measured in bytes
+                                              for 8 bits addressing or words for 16 bits addressing             */
+
+  uint32_t        BlockSize;             /*!< NAND memory block size measured in number of pages               */
+
+  uint32_t        BlockNbr;              /*!< NAND memory number of total blocks                               */
+
+  uint32_t        PlaneNbr;              /*!< NAND memory number of planes                                     */
+
+  uint32_t        PlaneSize;             /*!< NAND memory zone size measured in number of blocks               */
+
+  FunctionalState ExtraCommandEnable;    /*!< NAND extra command needed for Page reading mode. This
+                                              parameter is mandatory for some NAND parts after the read
+                                              command (NAND_CMD_AREA_TRUE1) and before DATA reading sequence.
+                                              Example: Toshiba THTH58BYG3S0HBAI6.
+                                              This parameter could be ENABLE or DISABLE
+                                              Please check the Read Mode sequnece in the NAND device datasheet */
+} NAND_DeviceConfigTypeDef;
+
+/**
+  * @brief  NAND handle Structure definition
+  */
+#if (USE_HAL_NAND_REGISTER_CALLBACKS == 1)
+typedef struct __NAND_HandleTypeDef
+#else
+typedef struct
+#endif /* USE_HAL_NAND_REGISTER_CALLBACKS  */
+{
+  FSMC_NAND_TypeDef               *Instance;  /*!< Register base address                                 */
+
+  FSMC_NAND_InitTypeDef           Init;       /*!< NAND device control configuration parameters          */
+
+  HAL_LockTypeDef                Lock;       /*!< NAND locking object                                   */
+
+  __IO HAL_NAND_StateTypeDef     State;      /*!< NAND device access state                              */
+
+  NAND_DeviceConfigTypeDef       Config;     /*!< NAND phusical characteristic information structure    */
+
+#if (USE_HAL_NAND_REGISTER_CALLBACKS == 1)
+  void (* MspInitCallback)(struct __NAND_HandleTypeDef *hnand);               /*!< NAND Msp Init callback              */
+  void (* MspDeInitCallback)(struct __NAND_HandleTypeDef *hnand);             /*!< NAND Msp DeInit callback            */
+  void (* ItCallback)(struct __NAND_HandleTypeDef *hnand);                    /*!< NAND IT callback                    */
+#endif /* USE_HAL_NAND_REGISTER_CALLBACKS */
+} NAND_HandleTypeDef;
+
+#if (USE_HAL_NAND_REGISTER_CALLBACKS == 1)
+/**
+  * @brief  HAL NAND Callback ID enumeration definition
+  */
+typedef enum
+{
+  HAL_NAND_MSP_INIT_CB_ID       = 0x00U,  /*!< NAND MspInit Callback ID          */
+  HAL_NAND_MSP_DEINIT_CB_ID     = 0x01U,  /*!< NAND MspDeInit Callback ID        */
+  HAL_NAND_IT_CB_ID             = 0x02U   /*!< NAND IT Callback ID               */
+} HAL_NAND_CallbackIDTypeDef;
+
+/**
+  * @brief  HAL NAND Callback pointer definition
+  */
+typedef void (*pNAND_CallbackTypeDef)(NAND_HandleTypeDef *hnand);
+#endif /* USE_HAL_NAND_REGISTER_CALLBACKS */
+
+/**
+  * @}
+  */
+
+/* Exported constants --------------------------------------------------------*/
+/* Exported macro ------------------------------------------------------------*/
+/** @defgroup NAND_Exported_Macros NAND Exported Macros
+  * @{
+  */
+
+/** @brief Reset NAND handle state
+  * @param  __HANDLE__ specifies the NAND handle.
+  * @retval None
+  */
+#if (USE_HAL_NAND_REGISTER_CALLBACKS == 1)
+#define __HAL_NAND_RESET_HANDLE_STATE(__HANDLE__)         do {                                             \
+                                                               (__HANDLE__)->State = HAL_NAND_STATE_RESET; \
+                                                               (__HANDLE__)->MspInitCallback = NULL;       \
+                                                               (__HANDLE__)->MspDeInitCallback = NULL;     \
+                                                             } while(0)
+#else
+#define __HAL_NAND_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_NAND_STATE_RESET)
+#endif /* USE_HAL_NAND_REGISTER_CALLBACKS */
+
+/**
+  * @}
+  */
+
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup NAND_Exported_Functions NAND Exported Functions
+  * @{
+  */
+
+/** @addtogroup NAND_Exported_Functions_Group1 Initialization and de-initialization functions
+  * @{
+  */
+
+/* Initialization/de-initialization functions  ********************************/
+HAL_StatusTypeDef  HAL_NAND_Init(NAND_HandleTypeDef *hnand, FSMC_NAND_PCC_TimingTypeDef *ComSpace_Timing,
+                                 FSMC_NAND_PCC_TimingTypeDef *AttSpace_Timing);
+HAL_StatusTypeDef  HAL_NAND_DeInit(NAND_HandleTypeDef *hnand);
+
+HAL_StatusTypeDef  HAL_NAND_ConfigDevice(NAND_HandleTypeDef *hnand, NAND_DeviceConfigTypeDef *pDeviceConfig);
+
+HAL_StatusTypeDef  HAL_NAND_Read_ID(NAND_HandleTypeDef *hnand, NAND_IDTypeDef *pNAND_ID);
+
+void               HAL_NAND_MspInit(NAND_HandleTypeDef *hnand);
+void               HAL_NAND_MspDeInit(NAND_HandleTypeDef *hnand);
+void               HAL_NAND_IRQHandler(NAND_HandleTypeDef *hnand);
+void               HAL_NAND_ITCallback(NAND_HandleTypeDef *hnand);
+
+/**
+  * @}
+  */
+
+/** @addtogroup NAND_Exported_Functions_Group2 Input and Output functions
+  * @{
+  */
+
+/* IO operation functions  ****************************************************/
+HAL_StatusTypeDef  HAL_NAND_Reset(NAND_HandleTypeDef *hnand);
+
+HAL_StatusTypeDef  HAL_NAND_Read_Page_8b(NAND_HandleTypeDef *hnand, NAND_AddressTypeDef *pAddress, uint8_t *pBuffer,
+                                         uint32_t NumPageToRead);
+HAL_StatusTypeDef  HAL_NAND_Write_Page_8b(NAND_HandleTypeDef *hnand, NAND_AddressTypeDef *pAddress, uint8_t *pBuffer,
+                                          uint32_t NumPageToWrite);
+HAL_StatusTypeDef  HAL_NAND_Read_SpareArea_8b(NAND_HandleTypeDef *hnand, NAND_AddressTypeDef *pAddress,
+                                              uint8_t *pBuffer, uint32_t NumSpareAreaToRead);
+HAL_StatusTypeDef  HAL_NAND_Write_SpareArea_8b(NAND_HandleTypeDef *hnand, NAND_AddressTypeDef *pAddress,
+                                               uint8_t *pBuffer, uint32_t NumSpareAreaTowrite);
+
+HAL_StatusTypeDef  HAL_NAND_Read_Page_16b(NAND_HandleTypeDef *hnand, NAND_AddressTypeDef *pAddress, uint16_t *pBuffer,
+                                          uint32_t NumPageToRead);
+HAL_StatusTypeDef  HAL_NAND_Write_Page_16b(NAND_HandleTypeDef *hnand, NAND_AddressTypeDef *pAddress, uint16_t *pBuffer,
+                                           uint32_t NumPageToWrite);
+HAL_StatusTypeDef  HAL_NAND_Read_SpareArea_16b(NAND_HandleTypeDef *hnand, NAND_AddressTypeDef *pAddress,
+                                               uint16_t *pBuffer, uint32_t NumSpareAreaToRead);
+HAL_StatusTypeDef  HAL_NAND_Write_SpareArea_16b(NAND_HandleTypeDef *hnand, NAND_AddressTypeDef *pAddress,
+                                                uint16_t *pBuffer, uint32_t NumSpareAreaTowrite);
+
+HAL_StatusTypeDef  HAL_NAND_Erase_Block(NAND_HandleTypeDef *hnand, NAND_AddressTypeDef *pAddress);
+
+uint32_t           HAL_NAND_Address_Inc(NAND_HandleTypeDef *hnand, NAND_AddressTypeDef *pAddress);
+
+#if (USE_HAL_NAND_REGISTER_CALLBACKS == 1)
+/* NAND callback registering/unregistering */
+HAL_StatusTypeDef  HAL_NAND_RegisterCallback(NAND_HandleTypeDef *hnand, HAL_NAND_CallbackIDTypeDef CallbackId,
+                                             pNAND_CallbackTypeDef pCallback);
+HAL_StatusTypeDef  HAL_NAND_UnRegisterCallback(NAND_HandleTypeDef *hnand, HAL_NAND_CallbackIDTypeDef CallbackId);
+#endif /* USE_HAL_NAND_REGISTER_CALLBACKS */
+
+/**
+  * @}
+  */
+
+/** @addtogroup NAND_Exported_Functions_Group3 Peripheral Control functions
+  * @{
+  */
+
+/* NAND Control functions  ****************************************************/
+HAL_StatusTypeDef  HAL_NAND_ECC_Enable(NAND_HandleTypeDef *hnand);
+HAL_StatusTypeDef  HAL_NAND_ECC_Disable(NAND_HandleTypeDef *hnand);
+HAL_StatusTypeDef  HAL_NAND_GetECC(NAND_HandleTypeDef *hnand, uint32_t *ECCval, uint32_t Timeout);
+
+/**
+  * @}
+  */
+
+/** @addtogroup NAND_Exported_Functions_Group4 Peripheral State functions
+  * @{
+  */
+/* NAND State functions *******************************************************/
+HAL_NAND_StateTypeDef HAL_NAND_GetState(NAND_HandleTypeDef *hnand);
+uint32_t              HAL_NAND_Read_Status(NAND_HandleTypeDef *hnand);
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Private types -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private constants ---------------------------------------------------------*/
+/** @defgroup NAND_Private_Constants NAND Private Constants
+  * @{
+  */
+#define NAND_DEVICE1               0x70000000UL
+#define NAND_DEVICE2               0x80000000UL
+#define NAND_WRITE_TIMEOUT         0x01000000UL
+
+#define CMD_AREA                   (1UL<<16U)  /* A16 = CLE high */
+#define ADDR_AREA                  (1UL<<17U)  /* A17 = ALE high */
+
+#define NAND_CMD_AREA_A            ((uint8_t)0x00)
+#define NAND_CMD_AREA_B            ((uint8_t)0x01)
+#define NAND_CMD_AREA_C            ((uint8_t)0x50)
+#define NAND_CMD_AREA_TRUE1        ((uint8_t)0x30)
+
+#define NAND_CMD_WRITE0            ((uint8_t)0x80)
+#define NAND_CMD_WRITE_TRUE1       ((uint8_t)0x10)
+#define NAND_CMD_ERASE0            ((uint8_t)0x60)
+#define NAND_CMD_ERASE1            ((uint8_t)0xD0)
+#define NAND_CMD_READID            ((uint8_t)0x90)
+#define NAND_CMD_STATUS            ((uint8_t)0x70)
+#define NAND_CMD_LOCK_STATUS       ((uint8_t)0x7A)
+#define NAND_CMD_RESET             ((uint8_t)0xFF)
+
+/* NAND memory status */
+#define NAND_VALID_ADDRESS         0x00000100UL
+#define NAND_INVALID_ADDRESS       0x00000200UL
+#define NAND_TIMEOUT_ERROR         0x00000400UL
+#define NAND_BUSY                  0x00000000UL
+#define NAND_ERROR                 0x00000001UL
+#define NAND_READY                 0x00000040UL
+/**
+  * @}
+  */
+
+/* Private macros ------------------------------------------------------------*/
+/** @defgroup NAND_Private_Macros NAND Private Macros
+  * @{
+  */
+
+/**
+  * @brief  NAND memory address computation.
+  * @param  __ADDRESS__ NAND memory address.
+  * @param  __HANDLE__  NAND handle.
+  * @retval NAND Raw address value
+  */
+#define ARRAY_ADDRESS(__ADDRESS__ , __HANDLE__) ((__ADDRESS__)->Page + \
+                                                 (((__ADDRESS__)->Block + \
+                                                   (((__ADDRESS__)->Plane) * \
+                                                    ((__HANDLE__)->Config.PlaneSize))) * \
+                                                  ((__HANDLE__)->Config.BlockSize)))
+
+/**
+  * @brief  NAND memory Column address computation.
+  * @param  __HANDLE__ NAND handle.
+  * @retval NAND Raw address value
+  */
+#define COLUMN_ADDRESS( __HANDLE__) ((__HANDLE__)->Config.PageSize)
+
+/**
+  * @brief  NAND memory address cycling.
+  * @param  __ADDRESS__ NAND memory address.
+  * @retval NAND address cycling value.
+  */
+#define ADDR_1ST_CYCLE(__ADDRESS__)       (uint8_t)(__ADDRESS__)              /* 1st addressing cycle */
+#define ADDR_2ND_CYCLE(__ADDRESS__)       (uint8_t)((__ADDRESS__) >> 8)       /* 2nd addressing cycle */
+#define ADDR_3RD_CYCLE(__ADDRESS__)       (uint8_t)((__ADDRESS__) >> 16)      /* 3rd addressing cycle */
+#define ADDR_4TH_CYCLE(__ADDRESS__)       (uint8_t)((__ADDRESS__) >> 24)      /* 4th addressing cycle */
+
+/**
+  * @brief  NAND memory Columns cycling.
+  * @param  __ADDRESS__ NAND memory address.
+  * @retval NAND Column address cycling value.
+  */
+#define COLUMN_1ST_CYCLE(__ADDRESS__)       (uint8_t)((__ADDRESS__) & 0xFFU)    /* 1st Column addressing cycle */
+#define COLUMN_2ND_CYCLE(__ADDRESS__)       (uint8_t)((__ADDRESS__) >> 8)       /* 2nd Column addressing cycle */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#endif /* FSMC_BANK3 */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* STM32F1xx_HAL_NAND_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_nor.h

@@ -0,0 +1,329 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_hal_nor.h
+  * @author  MCD Application Team
+  * @brief   Header file of NOR HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                       opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef STM32F1xx_HAL_NOR_H
+#define STM32F1xx_HAL_NOR_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+#if defined(FSMC_BANK1)
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_ll_fsmc.h"
+
+/** @addtogroup STM32F1xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup NOR
+  * @{
+  */
+
+/* Exported typedef ----------------------------------------------------------*/
+/** @defgroup NOR_Exported_Types NOR Exported Types
+  * @{
+  */
+
+/**
+  * @brief  HAL SRAM State structures definition
+  */
+typedef enum
+{
+  HAL_NOR_STATE_RESET             = 0x00U,  /*!< NOR not yet initialized or disabled  */
+  HAL_NOR_STATE_READY             = 0x01U,  /*!< NOR initialized and ready for use    */
+  HAL_NOR_STATE_BUSY              = 0x02U,  /*!< NOR internal processing is ongoing   */
+  HAL_NOR_STATE_ERROR             = 0x03U,  /*!< NOR error state                      */
+  HAL_NOR_STATE_PROTECTED         = 0x04U   /*!< NOR NORSRAM device write protected   */
+} HAL_NOR_StateTypeDef;
+
+/**
+  * @brief  FSMC NOR Status typedef
+  */
+typedef enum
+{
+  HAL_NOR_STATUS_SUCCESS  = 0U,
+  HAL_NOR_STATUS_ONGOING,
+  HAL_NOR_STATUS_ERROR,
+  HAL_NOR_STATUS_TIMEOUT
+} HAL_NOR_StatusTypeDef;
+
+/**
+  * @brief  FSMC NOR ID typedef
+  */
+typedef struct
+{
+  uint16_t Manufacturer_Code;  /*!< Defines the device's manufacturer code used to identify the memory       */
+
+  uint16_t Device_Code1;
+
+  uint16_t Device_Code2;
+
+  uint16_t Device_Code3;       /*!< Defines the device's codes used to identify the memory.
+                                    These codes can be accessed by performing read operations with specific
+                                    control signals and addresses set.They can also be accessed by issuing
+                                    an Auto Select command                                                   */
+} NOR_IDTypeDef;
+
+/**
+  * @brief  FSMC NOR CFI typedef
+  */
+typedef struct
+{
+  /*!< Defines the information stored in the memory's Common flash interface
+       which contains a description of various electrical and timing parameters,
+       density information and functions supported by the memory                   */
+
+  uint16_t CFI_1;
+
+  uint16_t CFI_2;
+
+  uint16_t CFI_3;
+
+  uint16_t CFI_4;
+} NOR_CFITypeDef;
+
+/**
+  * @brief  NOR handle Structure definition
+  */
+#if (USE_HAL_NOR_REGISTER_CALLBACKS == 1)
+typedef struct __NOR_HandleTypeDef
+#else
+typedef struct
+#endif /* USE_HAL_NOR_REGISTER_CALLBACKS  */
+
+{
+  FSMC_NORSRAM_TypeDef           *Instance;    /*!< Register base address                        */
+
+  FSMC_NORSRAM_EXTENDED_TypeDef  *Extended;    /*!< Extended mode register base address          */
+
+  FSMC_NORSRAM_InitTypeDef       Init;         /*!< NOR device control configuration parameters  */
+
+  HAL_LockTypeDef               Lock;         /*!< NOR locking object                           */
+
+  __IO HAL_NOR_StateTypeDef     State;        /*!< NOR device access state                      */
+
+  uint32_t                      CommandSet;   /*!< NOR algorithm command set and control        */
+
+#if (USE_HAL_NOR_REGISTER_CALLBACKS == 1)
+  void (* MspInitCallback)(struct __NOR_HandleTypeDef *hnor);               /*!< NOR Msp Init callback              */
+  void (* MspDeInitCallback)(struct __NOR_HandleTypeDef *hnor);             /*!< NOR Msp DeInit callback            */
+#endif /* USE_HAL_NOR_REGISTER_CALLBACKS */
+} NOR_HandleTypeDef;
+
+#if (USE_HAL_NOR_REGISTER_CALLBACKS == 1)
+/**
+  * @brief  HAL NOR Callback ID enumeration definition
+  */
+typedef enum
+{
+  HAL_NOR_MSP_INIT_CB_ID       = 0x00U,  /*!< NOR MspInit Callback ID          */
+  HAL_NOR_MSP_DEINIT_CB_ID     = 0x01U   /*!< NOR MspDeInit Callback ID        */
+} HAL_NOR_CallbackIDTypeDef;
+
+/**
+  * @brief  HAL NOR Callback pointer definition
+  */
+typedef void (*pNOR_CallbackTypeDef)(NOR_HandleTypeDef *hnor);
+#endif /* USE_HAL_NOR_REGISTER_CALLBACKS */
+/**
+  * @}
+  */
+
+/* Exported constants --------------------------------------------------------*/
+/* Exported macro ------------------------------------------------------------*/
+/** @defgroup NOR_Exported_Macros NOR Exported Macros
+  * @{
+  */
+/** @brief Reset NOR handle state
+  * @param  __HANDLE__ specifies the NOR handle.
+  * @retval None
+  */
+#if (USE_HAL_NOR_REGISTER_CALLBACKS == 1)
+#define __HAL_NOR_RESET_HANDLE_STATE(__HANDLE__)          do {                                             \
+                                                               (__HANDLE__)->State = HAL_NOR_STATE_RESET;  \
+                                                               (__HANDLE__)->MspInitCallback = NULL;       \
+                                                               (__HANDLE__)->MspDeInitCallback = NULL;     \
+                                                             } while(0)
+#else
+#define __HAL_NOR_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_NOR_STATE_RESET)
+#endif /* USE_HAL_NOR_REGISTER_CALLBACKS */
+/**
+  * @}
+  */
+
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup NOR_Exported_Functions NOR Exported Functions
+  * @{
+  */
+
+/** @addtogroup NOR_Exported_Functions_Group1 Initialization and de-initialization functions
+  * @{
+  */
+
+/* Initialization/de-initialization functions  ********************************/
+HAL_StatusTypeDef HAL_NOR_Init(NOR_HandleTypeDef *hnor, FSMC_NORSRAM_TimingTypeDef *Timing,
+                               FSMC_NORSRAM_TimingTypeDef *ExtTiming);
+HAL_StatusTypeDef HAL_NOR_DeInit(NOR_HandleTypeDef *hnor);
+void HAL_NOR_MspInit(NOR_HandleTypeDef *hnor);
+void HAL_NOR_MspDeInit(NOR_HandleTypeDef *hnor);
+void HAL_NOR_MspWait(NOR_HandleTypeDef *hnor, uint32_t Timeout);
+/**
+  * @}
+  */
+
+/** @addtogroup NOR_Exported_Functions_Group2 Input and Output functions
+  * @{
+  */
+
+/* I/O operation functions  ***************************************************/
+HAL_StatusTypeDef HAL_NOR_Read_ID(NOR_HandleTypeDef *hnor, NOR_IDTypeDef *pNOR_ID);
+HAL_StatusTypeDef HAL_NOR_ReturnToReadMode(NOR_HandleTypeDef *hnor);
+HAL_StatusTypeDef HAL_NOR_Read(NOR_HandleTypeDef *hnor, uint32_t *pAddress, uint16_t *pData);
+HAL_StatusTypeDef HAL_NOR_Program(NOR_HandleTypeDef *hnor, uint32_t *pAddress, uint16_t *pData);
+
+HAL_StatusTypeDef HAL_NOR_ReadBuffer(NOR_HandleTypeDef *hnor, uint32_t uwAddress, uint16_t *pData,
+                                     uint32_t uwBufferSize);
+HAL_StatusTypeDef HAL_NOR_ProgramBuffer(NOR_HandleTypeDef *hnor, uint32_t uwAddress, uint16_t *pData,
+                                        uint32_t uwBufferSize);
+
+HAL_StatusTypeDef HAL_NOR_Erase_Block(NOR_HandleTypeDef *hnor, uint32_t BlockAddress, uint32_t Address);
+HAL_StatusTypeDef HAL_NOR_Erase_Chip(NOR_HandleTypeDef *hnor, uint32_t Address);
+HAL_StatusTypeDef HAL_NOR_Read_CFI(NOR_HandleTypeDef *hnor, NOR_CFITypeDef *pNOR_CFI);
+
+#if (USE_HAL_NOR_REGISTER_CALLBACKS == 1)
+/* NOR callback registering/unregistering */
+HAL_StatusTypeDef HAL_NOR_RegisterCallback(NOR_HandleTypeDef *hnor, HAL_NOR_CallbackIDTypeDef CallbackId,
+                                           pNOR_CallbackTypeDef pCallback);
+HAL_StatusTypeDef HAL_NOR_UnRegisterCallback(NOR_HandleTypeDef *hnor, HAL_NOR_CallbackIDTypeDef CallbackId);
+#endif /* USE_HAL_NOR_REGISTER_CALLBACKS */
+/**
+  * @}
+  */
+
+/** @addtogroup NOR_Exported_Functions_Group3 NOR Control functions
+  * @{
+  */
+
+/* NOR Control functions  *****************************************************/
+HAL_StatusTypeDef HAL_NOR_WriteOperation_Enable(NOR_HandleTypeDef *hnor);
+HAL_StatusTypeDef HAL_NOR_WriteOperation_Disable(NOR_HandleTypeDef *hnor);
+/**
+  * @}
+  */
+
+/** @addtogroup NOR_Exported_Functions_Group4 NOR State functions
+  * @{
+  */
+
+/* NOR State functions ********************************************************/
+HAL_NOR_StateTypeDef  HAL_NOR_GetState(NOR_HandleTypeDef *hnor);
+HAL_NOR_StatusTypeDef HAL_NOR_GetStatus(NOR_HandleTypeDef *hnor, uint32_t Address, uint32_t Timeout);
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Private types -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private constants ---------------------------------------------------------*/
+/** @defgroup NOR_Private_Constants NOR Private Constants
+  * @{
+  */
+/* NOR device IDs addresses */
+#define MC_ADDRESS               ((uint16_t)0x0000)
+#define DEVICE_CODE1_ADDR        ((uint16_t)0x0001)
+#define DEVICE_CODE2_ADDR        ((uint16_t)0x000E)
+#define DEVICE_CODE3_ADDR        ((uint16_t)0x000F)
+
+/* NOR CFI IDs addresses */
+#define CFI1_ADDRESS             ((uint16_t)0x0061)
+#define CFI2_ADDRESS             ((uint16_t)0x0062)
+#define CFI3_ADDRESS             ((uint16_t)0x0063)
+#define CFI4_ADDRESS             ((uint16_t)0x0064)
+
+/* NOR operation wait timeout */
+#define NOR_TMEOUT               ((uint16_t)0xFFFF)
+
+/* NOR memory data width */
+#define NOR_MEMORY_8B            ((uint8_t)0x00)
+#define NOR_MEMORY_16B           ((uint8_t)0x01)
+
+/* NOR memory device read/write start address */
+#define NOR_MEMORY_ADRESS1       (0x60000000U)
+#define NOR_MEMORY_ADRESS2       (0x64000000U)
+#define NOR_MEMORY_ADRESS3       (0x68000000U)
+#define NOR_MEMORY_ADRESS4       (0x6C000000U)
+/**
+  * @}
+  */
+
+/* Private macros ------------------------------------------------------------*/
+/** @defgroup NOR_Private_Macros NOR Private Macros
+  * @{
+  */
+/**
+  * @brief  NOR memory address shifting.
+  * @param  __NOR_ADDRESS NOR base address
+  * @param  __NOR_MEMORY_WIDTH_ NOR memory width
+  * @param  __ADDRESS__ NOR memory address
+  * @retval NOR shifted address value
+  */
+#define NOR_ADDR_SHIFT(__NOR_ADDRESS, __NOR_MEMORY_WIDTH_, __ADDRESS__)         \
+  ((uint32_t)(((__NOR_MEMORY_WIDTH_) == NOR_MEMORY_16B)?            \
+              ((uint32_t)((__NOR_ADDRESS) + (2U * (__ADDRESS__)))):              \
+              ((uint32_t)((__NOR_ADDRESS) + (__ADDRESS__)))))
+
+/**
+  * @brief  NOR memory write data to specified address.
+  * @param  __ADDRESS__ NOR memory address
+  * @param  __DATA__ Data to write
+  * @retval None
+  */
+#define NOR_WRITE(__ADDRESS__, __DATA__)   do{                                                             \
+                                               (*(__IO uint16_t *)((uint32_t)(__ADDRESS__)) = (__DATA__)); \
+                                               __DSB();                                                    \
+                                             } while(0)
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#endif /* FSMC_BANK1 */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* STM32F1xx_HAL_NOR_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_pccard.h

@@ -0,0 +1,284 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_hal_pccard.h
+  * @author  MCD Application Team
+  * @brief   Header file of PCCARD HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                       opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef STM32F1xx_HAL_PCCARD_H
+#define STM32F1xx_HAL_PCCARD_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+#if defined(FSMC_BANK4)
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_ll_fsmc.h"
+
+/** @addtogroup STM32F1xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup PCCARD
+  * @{
+  */
+
+/* Exported typedef ----------------------------------------------------------*/
+/** @defgroup PCCARD_Exported_Types PCCARD Exported Types
+  * @{
+  */
+
+/**
+  * @brief  HAL PCCARD State structures definition
+  */
+typedef enum
+{
+  HAL_PCCARD_STATE_RESET     = 0x00U,    /*!< PCCARD peripheral not yet initialized or disabled */
+  HAL_PCCARD_STATE_READY     = 0x01U,    /*!< PCCARD peripheral ready                           */
+  HAL_PCCARD_STATE_BUSY      = 0x02U,    /*!< PCCARD peripheral busy                            */
+  HAL_PCCARD_STATE_ERROR     = 0x04U     /*!< PCCARD peripheral error                           */
+} HAL_PCCARD_StateTypeDef;
+
+typedef enum
+{
+  HAL_PCCARD_STATUS_SUCCESS = 0U,
+  HAL_PCCARD_STATUS_ONGOING,
+  HAL_PCCARD_STATUS_ERROR,
+  HAL_PCCARD_STATUS_TIMEOUT
+} HAL_PCCARD_StatusTypeDef;
+
+/**
+  * @brief  FSMC_PCCARD handle Structure definition
+  */
+#if (USE_HAL_PCCARD_REGISTER_CALLBACKS == 1)
+typedef struct __PCCARD_HandleTypeDef
+#else
+typedef struct
+#endif /* USE_HAL_PCCARD_REGISTER_CALLBACKS  */
+{
+  FSMC_PCCARD_TypeDef           *Instance;              /*!< Register base address for PCCARD device          */
+
+  FSMC_PCCARD_InitTypeDef       Init;                   /*!< PCCARD device control configuration parameters   */
+
+  __IO HAL_PCCARD_StateTypeDef State;                  /*!< PCCARD device access state                       */
+
+  HAL_LockTypeDef              Lock;                   /*!< PCCARD Lock                                      */
+
+#if (USE_HAL_PCCARD_REGISTER_CALLBACKS == 1)
+  void (* MspInitCallback)(struct __PCCARD_HandleTypeDef *hpccard);               /*!< PCCARD Msp Init callback              */
+  void (* MspDeInitCallback)(struct __PCCARD_HandleTypeDef *hpccard);             /*!< PCCARD Msp DeInit callback            */
+  void (* ItCallback)(struct __PCCARD_HandleTypeDef *hpccard);                    /*!< PCCARD IT callback                    */
+#endif
+} PCCARD_HandleTypeDef;
+
+#if (USE_HAL_PCCARD_REGISTER_CALLBACKS == 1)
+/**
+  * @brief  HAL PCCARD Callback ID enumeration definition
+  */
+typedef enum
+{
+  HAL_PCCARD_MSP_INIT_CB_ID       = 0x00U,  /*!< PCCARD MspInit Callback ID          */
+  HAL_PCCARD_MSP_DEINIT_CB_ID     = 0x01U,  /*!< PCCARD MspDeInit Callback ID        */
+  HAL_PCCARD_IT_CB_ID             = 0x02U   /*!< PCCARD IT Callback ID               */
+} HAL_PCCARD_CallbackIDTypeDef;
+
+/**
+  * @brief  HAL PCCARD Callback pointer definition
+  */
+typedef void (*pPCCARD_CallbackTypeDef)(PCCARD_HandleTypeDef *hpccard);
+#endif
+/**
+  * @}
+  */
+
+/* Exported constants --------------------------------------------------------*/
+/* Exported macro ------------------------------------------------------------*/
+/** @defgroup PCCARD_Exported_Macros PCCARD Exported Macros
+  * @{
+  */
+/** @brief Reset PCCARD handle state
+  * @param  __HANDLE__ specifies the PCCARD handle.
+  * @retval None
+  */
+#if (USE_HAL_PCCARD_REGISTER_CALLBACKS == 1)
+#define __HAL_PCCARD_RESET_HANDLE_STATE(__HANDLE__)       do {                                               \
+                                                               (__HANDLE__)->State = HAL_PCCARD_STATE_RESET; \
+                                                               (__HANDLE__)->MspInitCallback = NULL;         \
+                                                               (__HANDLE__)->MspDeInitCallback = NULL;       \
+                                                             } while(0)
+#else
+#define __HAL_PCCARD_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_PCCARD_STATE_RESET)
+#endif
+/**
+  * @}
+  */
+
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup PCCARD_Exported_Functions
+  * @{
+  */
+
+/** @addtogroup PCCARD_Exported_Functions_Group1
+  * @{
+  */
+/* Initialization/de-initialization functions  **********************************/
+HAL_StatusTypeDef  HAL_PCCARD_Init(PCCARD_HandleTypeDef *hpccard, FSMC_NAND_PCC_TimingTypeDef *ComSpaceTiming,
+                                   FSMC_NAND_PCC_TimingTypeDef *AttSpaceTiming, FSMC_NAND_PCC_TimingTypeDef *IOSpaceTiming);
+HAL_StatusTypeDef  HAL_PCCARD_DeInit(PCCARD_HandleTypeDef *hpccard);
+void HAL_PCCARD_MspInit(PCCARD_HandleTypeDef *hpccard);
+void HAL_PCCARD_MspDeInit(PCCARD_HandleTypeDef *hpccard);
+/**
+  * @}
+  */
+
+/** @addtogroup PCCARD_Exported_Functions_Group2
+  * @{
+  */
+/* IO operation functions  *****************************************************/
+HAL_StatusTypeDef  HAL_PCCARD_Read_ID(PCCARD_HandleTypeDef *hpccard, uint8_t CompactFlash_ID[], uint8_t *pStatus);
+HAL_StatusTypeDef  HAL_PCCARD_Write_Sector(PCCARD_HandleTypeDef *hpccard, uint16_t *pBuffer, uint16_t SectorAddress,
+                                           uint8_t *pStatus);
+HAL_StatusTypeDef  HAL_PCCARD_Read_Sector(PCCARD_HandleTypeDef *hpccard, uint16_t *pBuffer, uint16_t SectorAddress,
+                                          uint8_t *pStatus);
+HAL_StatusTypeDef  HAL_PCCARD_Erase_Sector(PCCARD_HandleTypeDef *hpccard, uint16_t SectorAddress, uint8_t *pStatus);
+HAL_StatusTypeDef  HAL_PCCARD_Reset(PCCARD_HandleTypeDef *hpccard);
+void               HAL_PCCARD_IRQHandler(PCCARD_HandleTypeDef *hpccard);
+void               HAL_PCCARD_ITCallback(PCCARD_HandleTypeDef *hpccard);
+
+#if (USE_HAL_PCCARD_REGISTER_CALLBACKS == 1)
+/* PCCARD callback registering/unregistering */
+HAL_StatusTypeDef  HAL_PCCARD_RegisterCallback(PCCARD_HandleTypeDef *hpccard, HAL_PCCARD_CallbackIDTypeDef CallbackId,
+                                               pPCCARD_CallbackTypeDef pCallback);
+HAL_StatusTypeDef  HAL_PCCARD_UnRegisterCallback(PCCARD_HandleTypeDef *hpccard,
+                                                 HAL_PCCARD_CallbackIDTypeDef CallbackId);
+#endif
+/**
+  * @}
+  */
+
+/** @addtogroup PCCARD_Exported_Functions_Group3
+  * @{
+  */
+/* PCCARD State functions *******************************************************/
+HAL_PCCARD_StateTypeDef  HAL_PCCARD_GetState(PCCARD_HandleTypeDef *hpccard);
+HAL_PCCARD_StatusTypeDef HAL_PCCARD_GetStatus(PCCARD_HandleTypeDef *hpccard);
+HAL_PCCARD_StatusTypeDef HAL_PCCARD_ReadStatus(PCCARD_HandleTypeDef *hpccard);
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+/* Private types -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private constants ---------------------------------------------------------*/
+/** @defgroup PCCARD_Private_Constants PCCARD Private Constants
+  * @{
+  */
+#define PCCARD_DEVICE_ADDRESS             0x90000000U
+#define PCCARD_ATTRIBUTE_SPACE_ADDRESS    0x98000000U              /* Attribute space size to @0x9BFF FFFF */
+#define PCCARD_COMMON_SPACE_ADDRESS       PCCARD_DEVICE_ADDRESS    /* Common space size to @0x93FF FFFF    */
+#define PCCARD_IO_SPACE_ADDRESS           0x9C000000U              /* IO space size to @0x9FFF FFFF        */
+#define PCCARD_IO_SPACE_PRIMARY_ADDR      0x9C0001F0U              /* IO space size to @0x9FFF FFFF        */
+
+/* Flash-ATA registers description */
+#define ATA_DATA                       ((uint8_t)0x00)    /* Data register */
+#define ATA_SECTOR_COUNT               ((uint8_t)0x02)    /* Sector Count register */
+#define ATA_SECTOR_NUMBER              ((uint8_t)0x03)    /* Sector Number register */
+#define ATA_CYLINDER_LOW               ((uint8_t)0x04)    /* Cylinder low register */
+#define ATA_CYLINDER_HIGH              ((uint8_t)0x05)    /* Cylinder high register */
+#define ATA_CARD_HEAD                  ((uint8_t)0x06)    /* Card/Head register */
+#define ATA_STATUS_CMD                 ((uint8_t)0x07)    /* Status(read)/Command(write) register */
+#define ATA_STATUS_CMD_ALTERNATE       ((uint8_t)0x0E)    /* Alternate Status(read)/Command(write) register */
+#define ATA_COMMON_DATA_AREA           ((uint16_t)0x0400) /* Start of data area (for Common access only!) */
+#define ATA_CARD_CONFIGURATION         ((uint16_t)0x0202) /* Card Configuration and Status Register */
+
+/* Flash-ATA commands */
+#define ATA_READ_SECTOR_CMD            ((uint8_t)0x20)
+#define ATA_WRITE_SECTOR_CMD           ((uint8_t)0x30)
+#define ATA_ERASE_SECTOR_CMD           ((uint8_t)0xC0)
+#define ATA_IDENTIFY_CMD               ((uint8_t)0xEC)
+
+/* PC Card/Compact Flash status */
+#define PCCARD_TIMEOUT_ERROR           ((uint8_t)0x60)
+#define PCCARD_BUSY                    ((uint8_t)0x80)
+#define PCCARD_PROGR                   ((uint8_t)0x01)
+#define PCCARD_READY                   ((uint8_t)0x40)
+
+#define PCCARD_SECTOR_SIZE             255U               /* In half words */
+
+/**
+  * @}
+  */
+/* Compact Flash redefinition */
+#define HAL_CF_Init                 HAL_PCCARD_Init
+#define HAL_CF_DeInit               HAL_PCCARD_DeInit
+#define HAL_CF_MspInit              HAL_PCCARD_MspInit
+#define HAL_CF_MspDeInit            HAL_PCCARD_MspDeInit
+
+#define HAL_CF_Read_ID              HAL_PCCARD_Read_ID
+#define HAL_CF_Write_Sector         HAL_PCCARD_Write_Sector
+#define HAL_CF_Read_Sector          HAL_PCCARD_Read_Sector
+#define HAL_CF_Erase_Sector         HAL_PCCARD_Erase_Sector
+#define HAL_CF_Reset                HAL_PCCARD_Reset
+#define HAL_CF_IRQHandler           HAL_PCCARD_IRQHandler
+#define HAL_CF_ITCallback           HAL_PCCARD_ITCallback
+
+#define HAL_CF_GetState             HAL_PCCARD_GetState
+#define HAL_CF_GetStatus            HAL_PCCARD_GetStatus
+#define HAL_CF_ReadStatus           HAL_PCCARD_ReadStatus
+
+#define HAL_CF_STATUS_SUCCESS       HAL_PCCARD_STATUS_SUCCESS
+#define HAL_CF_STATUS_ONGOING       HAL_PCCARD_STATUS_ONGOING
+#define HAL_CF_STATUS_ERROR         HAL_PCCARD_STATUS_ERROR
+#define HAL_CF_STATUS_TIMEOUT       HAL_PCCARD_STATUS_TIMEOUT
+#define HAL_CF_StatusTypeDef        HAL_PCCARD_StatusTypeDef
+
+#define CF_DEVICE_ADDRESS           PCCARD_DEVICE_ADDRESS
+#define CF_ATTRIBUTE_SPACE_ADDRESS  PCCARD_ATTRIBUTE_SPACE_ADDRESS
+#define CF_COMMON_SPACE_ADDRESS     PCCARD_COMMON_SPACE_ADDRESS
+#define CF_IO_SPACE_ADDRESS         PCCARD_IO_SPACE_ADDRESS
+#define CF_IO_SPACE_PRIMARY_ADDR    PCCARD_IO_SPACE_PRIMARY_ADDR
+
+#define CF_TIMEOUT_ERROR            PCCARD_TIMEOUT_ERROR
+#define CF_BUSY                     PCCARD_BUSY
+#define CF_PROGR                    PCCARD_PROGR
+#define CF_READY                    PCCARD_READY
+
+#define CF_SECTOR_SIZE              PCCARD_SECTOR_SIZE
+
+/* Private macros ------------------------------------------------------------*/
+/**
+  * @}
+  */
+
+
+/**
+  * @}
+  */
+
+#endif /* FSMC_BANK4 */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* STM32F1xx_HAL_PCCARD_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_pcd_ex.h

@@ -0,0 +1,88 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_hal_pcd_ex.h
+  * @author  MCD Application Team
+  * @brief   Header file of PCD HAL Extension module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef STM32F1xx_HAL_PCD_EX_H
+#define STM32F1xx_HAL_PCD_EX_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_hal_def.h"
+
+#if defined (USB) || defined (USB_OTG_FS)
+/** @addtogroup STM32F1xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup PCDEx
+  * @{
+  */
+/* Exported types ------------------------------------------------------------*/
+/* Exported constants --------------------------------------------------------*/
+/* Exported macros -----------------------------------------------------------*/
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup PCDEx_Exported_Functions PCDEx Exported Functions
+  * @{
+  */
+/** @addtogroup PCDEx_Exported_Functions_Group1 Peripheral Control functions
+  * @{
+  */
+
+#if defined (USB_OTG_FS)
+HAL_StatusTypeDef HAL_PCDEx_SetTxFiFo(PCD_HandleTypeDef *hpcd, uint8_t fifo, uint16_t size);
+HAL_StatusTypeDef HAL_PCDEx_SetRxFiFo(PCD_HandleTypeDef *hpcd, uint16_t size);
+#endif /* defined (USB_OTG_FS) */
+
+#if defined (USB)
+HAL_StatusTypeDef  HAL_PCDEx_PMAConfig(PCD_HandleTypeDef *hpcd, uint16_t ep_addr,
+                                       uint16_t ep_kind, uint32_t pmaadress);
+
+void HAL_PCDEx_SetConnectionState(PCD_HandleTypeDef *hpcd, uint8_t state);
+#endif /* defined (USB) */
+void HAL_PCDEx_LPM_Callback(PCD_HandleTypeDef *hpcd, PCD_LPM_MsgTypeDef msg);
+void HAL_PCDEx_BCD_Callback(PCD_HandleTypeDef *hpcd, PCD_BCD_MsgTypeDef msg);
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+#endif /* defined (USB) || defined (USB_OTG_FS) */
+
+#ifdef __cplusplus
+}
+#endif
+
+
+#endif /* STM32F1xx_HAL_PCD_EX_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_pwr.h

@@ -0,0 +1,388 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_hal_pwr.h
+  * @author  MCD Application Team
+  * @brief   Header file of PWR HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F1xx_HAL_PWR_H
+#define __STM32F1xx_HAL_PWR_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_hal_def.h"
+
+/** @addtogroup STM32F1xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup PWR
+  * @{
+  */
+
+/* Exported types ------------------------------------------------------------*/
+
+/** @defgroup PWR_Exported_Types PWR Exported Types
+  * @{
+  */ 
+
+/**
+  * @brief  PWR PVD configuration structure definition
+  */
+typedef struct
+{
+  uint32_t PVDLevel;   /*!< PVDLevel: Specifies the PVD detection level.
+                            This parameter can be a value of @ref PWR_PVD_detection_level */
+
+  uint32_t Mode;      /*!< Mode: Specifies the operating mode for the selected pins.
+                           This parameter can be a value of @ref PWR_PVD_Mode */
+}PWR_PVDTypeDef;
+
+
+/**
+  * @}
+  */
+
+
+/* Internal constants --------------------------------------------------------*/
+
+/** @addtogroup PWR_Private_Constants
+  * @{
+  */ 
+
+#define PWR_EXTI_LINE_PVD  ((uint32_t)0x00010000)  /*!< External interrupt line 16 Connected to the PVD EXTI Line */
+
+/**
+  * @}
+  */
+
+ 
+/* Exported constants --------------------------------------------------------*/
+
+/** @defgroup PWR_Exported_Constants PWR Exported Constants
+  * @{
+  */ 
+
+/** @defgroup PWR_PVD_detection_level PWR PVD detection level
+  * @{
+  */
+#define PWR_PVDLEVEL_0                  PWR_CR_PLS_2V2
+#define PWR_PVDLEVEL_1                  PWR_CR_PLS_2V3
+#define PWR_PVDLEVEL_2                  PWR_CR_PLS_2V4
+#define PWR_PVDLEVEL_3                  PWR_CR_PLS_2V5
+#define PWR_PVDLEVEL_4                  PWR_CR_PLS_2V6
+#define PWR_PVDLEVEL_5                  PWR_CR_PLS_2V7
+#define PWR_PVDLEVEL_6                  PWR_CR_PLS_2V8
+#define PWR_PVDLEVEL_7                  PWR_CR_PLS_2V9 
+                                                          
+/**
+  * @}
+  */
+
+/** @defgroup PWR_PVD_Mode PWR PVD Mode
+  * @{
+  */
+#define PWR_PVD_MODE_NORMAL                 0x00000000U   /*!< basic mode is used */
+#define PWR_PVD_MODE_IT_RISING              0x00010001U   /*!< External Interrupt Mode with Rising edge trigger detection */
+#define PWR_PVD_MODE_IT_FALLING             0x00010002U   /*!< External Interrupt Mode with Falling edge trigger detection */
+#define PWR_PVD_MODE_IT_RISING_FALLING      0x00010003U   /*!< External Interrupt Mode with Rising/Falling edge trigger detection */
+#define PWR_PVD_MODE_EVENT_RISING           0x00020001U   /*!< Event Mode with Rising edge trigger detection */
+#define PWR_PVD_MODE_EVENT_FALLING          0x00020002U   /*!< Event Mode with Falling edge trigger detection */
+#define PWR_PVD_MODE_EVENT_RISING_FALLING   0x00020003U   /*!< Event Mode with Rising/Falling edge trigger detection */
+
+/**
+  * @}
+  */
+
+
+/** @defgroup PWR_WakeUp_Pins PWR WakeUp Pins
+  * @{
+  */
+
+#define PWR_WAKEUP_PIN1                 PWR_CSR_EWUP
+
+/**
+  * @}
+  */
+
+/** @defgroup PWR_Regulator_state_in_SLEEP_STOP_mode PWR Regulator state in SLEEP/STOP mode
+  * @{
+  */
+#define PWR_MAINREGULATOR_ON                        0x00000000U
+#define PWR_LOWPOWERREGULATOR_ON                    PWR_CR_LPDS
+
+/**
+  * @}
+  */
+
+/** @defgroup PWR_SLEEP_mode_entry PWR SLEEP mode entry
+  * @{
+  */
+#define PWR_SLEEPENTRY_WFI              ((uint8_t)0x01)
+#define PWR_SLEEPENTRY_WFE              ((uint8_t)0x02)
+
+/**
+  * @}
+  */
+
+/** @defgroup PWR_STOP_mode_entry PWR STOP mode entry
+  * @{
+  */
+#define PWR_STOPENTRY_WFI               ((uint8_t)0x01)
+#define PWR_STOPENTRY_WFE               ((uint8_t)0x02)
+
+/**
+  * @}
+  */
+
+/** @defgroup PWR_Flag PWR Flag
+  * @{
+  */
+#define PWR_FLAG_WU                     PWR_CSR_WUF
+#define PWR_FLAG_SB                     PWR_CSR_SBF
+#define PWR_FLAG_PVDO                   PWR_CSR_PVDO
+
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Exported macro ------------------------------------------------------------*/
+/** @defgroup PWR_Exported_Macros PWR Exported Macros
+  * @{
+  */
+
+/** @brief  Check PWR flag is set or not.
+  * @param  __FLAG__: specifies the flag to check.
+  *           This parameter can be one of the following values:
+  *            @arg PWR_FLAG_WU: Wake Up flag. This flag indicates that a wakeup event
+  *                  was received from the WKUP pin or from the RTC alarm
+  *                  An additional wakeup event is detected if the WKUP pin is enabled
+  *                  (by setting the EWUP bit) when the WKUP pin level is already high.
+  *            @arg PWR_FLAG_SB: StandBy flag. This flag indicates that the system was
+  *                  resumed from StandBy mode.
+  *            @arg PWR_FLAG_PVDO: PVD Output. This flag is valid only if PVD is enabled
+  *                  by the HAL_PWR_EnablePVD() function. The PVD is stopped by Standby mode
+  *                  For this reason, this bit is equal to 0 after Standby or reset
+  *                  until the PVDE bit is set.
+  * @retval The new state of __FLAG__ (TRUE or FALSE).
+  */
+#define __HAL_PWR_GET_FLAG(__FLAG__) ((PWR->CSR & (__FLAG__)) == (__FLAG__))
+
+/** @brief  Clear the PWR's pending flags.
+  * @param  __FLAG__: specifies the flag to clear.
+  *          This parameter can be one of the following values:
+  *            @arg PWR_FLAG_WU: Wake Up flag
+  *            @arg PWR_FLAG_SB: StandBy flag
+  */
+#define __HAL_PWR_CLEAR_FLAG(__FLAG__) SET_BIT(PWR->CR, ((__FLAG__) << 2))
+
+/**
+  * @brief Enable interrupt on PVD Exti Line 16.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_ENABLE_IT()      SET_BIT(EXTI->IMR, PWR_EXTI_LINE_PVD)
+
+/**
+  * @brief Disable interrupt on PVD Exti Line 16. 
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_DISABLE_IT()     CLEAR_BIT(EXTI->IMR, PWR_EXTI_LINE_PVD)
+
+/**
+  * @brief Enable event on PVD Exti Line 16.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_ENABLE_EVENT()   SET_BIT(EXTI->EMR, PWR_EXTI_LINE_PVD)
+
+/**
+  * @brief Disable event on PVD Exti Line 16.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_DISABLE_EVENT()  CLEAR_BIT(EXTI->EMR, PWR_EXTI_LINE_PVD)
+
+
+/**
+  * @brief  PVD EXTI line configuration: set falling edge trigger.  
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_ENABLE_FALLING_EDGE()  SET_BIT(EXTI->FTSR, PWR_EXTI_LINE_PVD)
+
+
+/**
+  * @brief Disable the PVD Extended Interrupt Falling Trigger.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_DISABLE_FALLING_EDGE()  CLEAR_BIT(EXTI->FTSR, PWR_EXTI_LINE_PVD)
+
+
+/**
+  * @brief  PVD EXTI line configuration: set rising edge trigger.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_ENABLE_RISING_EDGE()   SET_BIT(EXTI->RTSR, PWR_EXTI_LINE_PVD)
+
+/**
+  * @brief Disable the PVD Extended Interrupt Rising Trigger.
+  * This parameter can be:
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_DISABLE_RISING_EDGE()  CLEAR_BIT(EXTI->RTSR, PWR_EXTI_LINE_PVD)
+
+/**
+  * @brief  PVD EXTI line configuration: set rising & falling edge trigger.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_ENABLE_RISING_FALLING_EDGE()   __HAL_PWR_PVD_EXTI_ENABLE_RISING_EDGE();__HAL_PWR_PVD_EXTI_ENABLE_FALLING_EDGE();
+
+/**
+  * @brief Disable the PVD Extended Interrupt Rising & Falling Trigger.
+  * This parameter can be:
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_DISABLE_RISING_FALLING_EDGE()  __HAL_PWR_PVD_EXTI_DISABLE_RISING_EDGE();__HAL_PWR_PVD_EXTI_DISABLE_FALLING_EDGE();
+
+
+
+/**
+  * @brief Check whether the specified PVD EXTI interrupt flag is set or not.
+  * @retval EXTI PVD Line Status.
+  */
+#define __HAL_PWR_PVD_EXTI_GET_FLAG()       (EXTI->PR & (PWR_EXTI_LINE_PVD))
+
+/**
+  * @brief Clear the PVD EXTI flag.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_CLEAR_FLAG()     (EXTI->PR = (PWR_EXTI_LINE_PVD))
+
+/**
+  * @brief Generate a Software interrupt on selected EXTI line.
+  * @retval None.
+  */
+#define __HAL_PWR_PVD_EXTI_GENERATE_SWIT()  SET_BIT(EXTI->SWIER, PWR_EXTI_LINE_PVD)
+/**
+  * @}
+  */
+
+/* Private macro -------------------------------------------------------------*/
+/** @defgroup PWR_Private_Macros PWR Private Macros
+  * @{
+  */
+#define IS_PWR_PVD_LEVEL(LEVEL) (((LEVEL) == PWR_PVDLEVEL_0) || ((LEVEL) == PWR_PVDLEVEL_1)|| \
+                                 ((LEVEL) == PWR_PVDLEVEL_2) || ((LEVEL) == PWR_PVDLEVEL_3)|| \
+                                 ((LEVEL) == PWR_PVDLEVEL_4) || ((LEVEL) == PWR_PVDLEVEL_5)|| \
+                                 ((LEVEL) == PWR_PVDLEVEL_6) || ((LEVEL) == PWR_PVDLEVEL_7))
+
+
+#define IS_PWR_PVD_MODE(MODE) (((MODE) == PWR_PVD_MODE_IT_RISING)|| ((MODE) == PWR_PVD_MODE_IT_FALLING) || \
+                              ((MODE) == PWR_PVD_MODE_IT_RISING_FALLING) || ((MODE) == PWR_PVD_MODE_EVENT_RISING) || \
+                              ((MODE) == PWR_PVD_MODE_EVENT_FALLING) || ((MODE) == PWR_PVD_MODE_EVENT_RISING_FALLING) || \
+                              ((MODE) == PWR_PVD_MODE_NORMAL)) 
+
+#define IS_PWR_WAKEUP_PIN(PIN) (((PIN) == PWR_WAKEUP_PIN1))
+
+#define IS_PWR_REGULATOR(REGULATOR) (((REGULATOR) == PWR_MAINREGULATOR_ON) || \
+                                     ((REGULATOR) == PWR_LOWPOWERREGULATOR_ON))
+
+#define IS_PWR_SLEEP_ENTRY(ENTRY) (((ENTRY) == PWR_SLEEPENTRY_WFI) || ((ENTRY) == PWR_SLEEPENTRY_WFE))
+
+#define IS_PWR_STOP_ENTRY(ENTRY) (((ENTRY) == PWR_STOPENTRY_WFI) || ((ENTRY) == PWR_STOPENTRY_WFE))
+
+/**
+  * @}
+  */
+
+
+
+/* Exported functions --------------------------------------------------------*/
+
+/** @addtogroup PWR_Exported_Functions PWR Exported Functions
+  * @{
+  */
+  
+/** @addtogroup PWR_Exported_Functions_Group1 Initialization and de-initialization functions 
+  * @{
+  */
+
+/* Initialization and de-initialization functions *******************************/
+void HAL_PWR_DeInit(void);
+void HAL_PWR_EnableBkUpAccess(void);
+void HAL_PWR_DisableBkUpAccess(void);
+
+/**
+  * @}
+  */
+
+/** @addtogroup PWR_Exported_Functions_Group2 Peripheral Control functions 
+  * @{
+  */
+
+/* Peripheral Control functions  ************************************************/
+void HAL_PWR_ConfigPVD(PWR_PVDTypeDef *sConfigPVD);
+/* #define HAL_PWR_ConfigPVD 12*/
+void HAL_PWR_EnablePVD(void);
+void HAL_PWR_DisablePVD(void);
+
+/* WakeUp pins configuration functions ****************************************/
+void HAL_PWR_EnableWakeUpPin(uint32_t WakeUpPinx);
+void HAL_PWR_DisableWakeUpPin(uint32_t WakeUpPinx);
+
+/* Low Power modes configuration functions ************************************/
+void HAL_PWR_EnterSTOPMode(uint32_t Regulator, uint8_t STOPEntry);
+void HAL_PWR_EnterSLEEPMode(uint32_t Regulator, uint8_t SLEEPEntry);
+void HAL_PWR_EnterSTANDBYMode(void);
+
+void HAL_PWR_EnableSleepOnExit(void);
+void HAL_PWR_DisableSleepOnExit(void);
+void HAL_PWR_EnableSEVOnPend(void);
+void HAL_PWR_DisableSEVOnPend(void);
+
+
+
+void HAL_PWR_PVD_IRQHandler(void);
+void HAL_PWR_PVDCallback(void);
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+
+#endif /* __STM32F1xx_HAL_PWR_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_rtc.h

@@ -0,0 +1,607 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_hal_rtc.h
+  * @author  MCD Application Team
+  * @brief   Header file of RTC HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F1xx_HAL_RTC_H
+#define __STM32F1xx_HAL_RTC_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_hal_def.h"
+
+/** @addtogroup STM32F1xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup RTC
+  * @{
+  */
+
+/** @addtogroup RTC_Private_Macros
+  * @{
+  */
+
+#define IS_RTC_ASYNCH_PREDIV(PREDIV)  (((PREDIV) <= 0xFFFFFU) || ((PREDIV) == RTC_AUTO_1_SECOND))
+#define IS_RTC_HOUR24(HOUR)           ((HOUR) <= 23U)
+#define IS_RTC_MINUTES(MINUTES)       ((MINUTES) <= 59U)
+#define IS_RTC_SECONDS(SECONDS)       ((SECONDS) <= 59U)
+#define IS_RTC_FORMAT(FORMAT)         (((FORMAT) == RTC_FORMAT_BIN) || ((FORMAT) == RTC_FORMAT_BCD))
+#define IS_RTC_YEAR(YEAR)             ((YEAR) <= 99U)
+#define IS_RTC_MONTH(MONTH)           (((MONTH) >= 1U) && ((MONTH) <= 12U))
+#define IS_RTC_DATE(DATE)             (((DATE) >= 1U) && ((DATE) <= 31U))
+#define IS_RTC_ALARM(ALARM)           ((ALARM) == RTC_ALARM_A)
+#define IS_RTC_CALIB_OUTPUT(__OUTPUT__) (((__OUTPUT__) == RTC_OUTPUTSOURCE_NONE) || \
+                                         ((__OUTPUT__) == RTC_OUTPUTSOURCE_CALIBCLOCK) || \
+                                         ((__OUTPUT__) == RTC_OUTPUTSOURCE_ALARM) || \
+                                         ((__OUTPUT__) == RTC_OUTPUTSOURCE_SECOND))
+
+
+/**
+  * @}
+  */
+
+/** @addtogroup RTC_Private_Constants
+  * @{
+  */
+/** @defgroup RTC_Timeout_Value Default Timeout Value
+  * @{
+  */
+#define RTC_TIMEOUT_VALUE           1000U
+/**
+  * @}
+  */
+
+/** @defgroup RTC_EXTI_Line_Event RTC EXTI Line event
+  * @{
+  */
+#define RTC_EXTI_LINE_ALARM_EVENT   ((uint32_t)EXTI_IMR_MR17)  /*!< External interrupt line 17 Connected to the RTC Alarm event */
+/**
+  * @}
+  */
+
+
+/**
+  * @}
+  */
+
+/* Exported types ------------------------------------------------------------*/
+/** @defgroup RTC_Exported_Types RTC Exported Types
+  * @{
+  */
+/**
+  * @brief  RTC Time structure definition
+  */
+typedef struct
+{
+  uint8_t Hours;            /*!< Specifies the RTC Time Hour.
+                                 This parameter must be a number between Min_Data = 0 and Max_Data = 23 */
+
+  uint8_t Minutes;          /*!< Specifies the RTC Time Minutes.
+                                 This parameter must be a number between Min_Data = 0 and Max_Data = 59 */
+
+  uint8_t Seconds;          /*!< Specifies the RTC Time Seconds.
+                                 This parameter must be a number between Min_Data = 0 and Max_Data = 59 */
+
+} RTC_TimeTypeDef;
+
+/**
+  * @brief  RTC Alarm structure definition
+  */
+typedef struct
+{
+  RTC_TimeTypeDef AlarmTime;     /*!< Specifies the RTC Alarm Time members */
+
+  uint32_t Alarm;                /*!< Specifies the alarm ID (only 1 alarm ID for STM32F1).
+                                      This parameter can be a value of @ref RTC_Alarms_Definitions */
+} RTC_AlarmTypeDef;
+
+/**
+  * @brief  HAL State structures definition
+  */
+typedef enum
+{
+  HAL_RTC_STATE_RESET             = 0x00U,  /*!< RTC not yet initialized or disabled */
+  HAL_RTC_STATE_READY             = 0x01U,  /*!< RTC initialized and ready for use   */
+  HAL_RTC_STATE_BUSY              = 0x02U,  /*!< RTC process is ongoing              */
+  HAL_RTC_STATE_TIMEOUT           = 0x03U,  /*!< RTC timeout state                   */
+  HAL_RTC_STATE_ERROR             = 0x04U   /*!< RTC error state                     */
+
+} HAL_RTCStateTypeDef;
+
+/**
+  * @brief  RTC Configuration Structure definition
+  */
+typedef struct
+{
+  uint32_t AsynchPrediv;    /*!< Specifies the RTC Asynchronous Predivider value.
+                                 This parameter must be a number between Min_Data = 0x00 and Max_Data = 0xFFFFF  or RTC_AUTO_1_SECOND
+                                 If RTC_AUTO_1_SECOND is selected, AsynchPrediv will be set automatically to get 1sec timebase */
+
+  uint32_t OutPut;          /*!< Specifies which signal will be routed to the RTC Tamper pin.
+                                 This parameter can be a value of @ref RTC_output_source_to_output_on_the_Tamper_pin */
+
+} RTC_InitTypeDef;
+
+/**
+  * @brief  RTC Date structure definition
+  */
+typedef struct
+{
+  uint8_t WeekDay;  /*!< Specifies the RTC Date WeekDay (not necessary for HAL_RTC_SetDate).
+                         This parameter can be a value of @ref RTC_WeekDay_Definitions */
+
+  uint8_t Month;    /*!< Specifies the RTC Date Month (in BCD format).
+                         This parameter can be a value of @ref RTC_Month_Date_Definitions */
+
+  uint8_t Date;     /*!< Specifies the RTC Date.
+                         This parameter must be a number between Min_Data = 1 and Max_Data = 31 */
+
+  uint8_t Year;     /*!< Specifies the RTC Date Year.
+                         This parameter must be a number between Min_Data = 0 and Max_Data = 99 */
+
+} RTC_DateTypeDef;
+
+/**
+  * @brief  Time Handle Structure definition
+  */
+#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1)
+typedef struct __RTC_HandleTypeDef
+#else
+typedef struct
+#endif /* (USE_HAL_RTC_REGISTER_CALLBACKS) */
+{
+  RTC_TypeDef                 *Instance;  /*!< Register base address    */
+
+  RTC_InitTypeDef             Init;       /*!< RTC required parameters  */
+
+  RTC_DateTypeDef             DateToUpdate;       /*!< Current date set by user and updated automatically  */
+
+  HAL_LockTypeDef             Lock;       /*!< RTC locking object       */
+
+  __IO HAL_RTCStateTypeDef    State;      /*!< Time communication state */
+
+#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1)
+  void (* AlarmAEventCallback)(struct __RTC_HandleTypeDef *hrtc);           /*!< RTC Alarm A Event callback         */
+
+  void (* Tamper1EventCallback)(struct __RTC_HandleTypeDef *hrtc);          /*!< RTC Tamper 1 Event callback        */
+
+  void (* MspInitCallback)(struct __RTC_HandleTypeDef *hrtc);               /*!< RTC Msp Init callback              */
+
+  void (* MspDeInitCallback)(struct __RTC_HandleTypeDef *hrtc);             /*!< RTC Msp DeInit callback            */
+
+#endif /* (USE_HAL_RTC_REGISTER_CALLBACKS) */
+
+} RTC_HandleTypeDef;
+
+#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1)
+/**
+  * @brief  HAL RTC Callback ID enumeration definition
+  */
+typedef enum
+{
+  HAL_RTC_ALARM_A_EVENT_CB_ID           = 0x00u,    /*!< RTC Alarm A Event Callback ID       */
+  HAL_RTC_TAMPER1_EVENT_CB_ID           = 0x04u,    /*!< RTC Tamper 1 Callback ID            */
+  HAL_RTC_MSPINIT_CB_ID                 = 0x0Eu,    /*!< RTC Msp Init callback ID            */
+  HAL_RTC_MSPDEINIT_CB_ID               = 0x0Fu     /*!< RTC Msp DeInit callback ID          */
+} HAL_RTC_CallbackIDTypeDef;
+
+/**
+  * @brief  HAL RTC Callback pointer definition
+  */
+typedef  void (*pRTC_CallbackTypeDef)(RTC_HandleTypeDef *hrtc);  /*!< pointer to an RTC callback function */
+#endif /* USE_HAL_RTC_REGISTER_CALLBACKS */
+
+/**
+  * @}
+  */
+
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup RTC_Exported_Constants RTC Exported Constants
+  * @{
+  */
+
+/** @defgroup RTC_Automatic_Prediv_1_Second Automatic calculation of prediv for 1sec timebase
+  * @{
+  */
+#define RTC_AUTO_1_SECOND                      0xFFFFFFFFU
+
+/**
+  * @}
+  */
+
+/** @defgroup RTC_Input_parameter_format_definitions Input Parameter Format
+  * @{
+  */
+#define RTC_FORMAT_BIN                         0x000000000U
+#define RTC_FORMAT_BCD                         0x000000001U
+
+/**
+  * @}
+  */
+
+/** @defgroup RTC_Month_Date_Definitions Month Definitions
+  * @{
+  */
+
+/* Coded in BCD format */
+#define RTC_MONTH_JANUARY              ((uint8_t)0x01)
+#define RTC_MONTH_FEBRUARY             ((uint8_t)0x02)
+#define RTC_MONTH_MARCH                ((uint8_t)0x03)
+#define RTC_MONTH_APRIL                ((uint8_t)0x04)
+#define RTC_MONTH_MAY                  ((uint8_t)0x05)
+#define RTC_MONTH_JUNE                 ((uint8_t)0x06)
+#define RTC_MONTH_JULY                 ((uint8_t)0x07)
+#define RTC_MONTH_AUGUST               ((uint8_t)0x08)
+#define RTC_MONTH_SEPTEMBER            ((uint8_t)0x09)
+#define RTC_MONTH_OCTOBER              ((uint8_t)0x10)
+#define RTC_MONTH_NOVEMBER             ((uint8_t)0x11)
+#define RTC_MONTH_DECEMBER             ((uint8_t)0x12)
+
+/**
+  * @}
+  */
+
+/** @defgroup RTC_WeekDay_Definitions WeekDay Definitions
+  * @{
+  */
+#define RTC_WEEKDAY_MONDAY             ((uint8_t)0x01)
+#define RTC_WEEKDAY_TUESDAY            ((uint8_t)0x02)
+#define RTC_WEEKDAY_WEDNESDAY          ((uint8_t)0x03)
+#define RTC_WEEKDAY_THURSDAY           ((uint8_t)0x04)
+#define RTC_WEEKDAY_FRIDAY             ((uint8_t)0x05)
+#define RTC_WEEKDAY_SATURDAY           ((uint8_t)0x06)
+#define RTC_WEEKDAY_SUNDAY             ((uint8_t)0x00)
+
+/**
+  * @}
+  */
+
+/** @defgroup RTC_Alarms_Definitions Alarms Definitions
+  * @{
+  */
+#define RTC_ALARM_A                        0U                                 /*!< Specify alarm ID (mainly for legacy purposes) */
+
+/**
+  * @}
+  */
+
+
+/** @defgroup RTC_output_source_to_output_on_the_Tamper_pin Output source to output on the Tamper pin
+  * @{
+  */
+
+#define RTC_OUTPUTSOURCE_NONE               0x00000000U                       /*!< No output on the TAMPER pin  */
+#define RTC_OUTPUTSOURCE_CALIBCLOCK         BKP_RTCCR_CCO                     /*!< RTC clock with a frequency divided by 64 on the TAMPER pin  */
+#define RTC_OUTPUTSOURCE_ALARM              BKP_RTCCR_ASOE                    /*!< Alarm pulse signal on the TAMPER pin  */
+#define RTC_OUTPUTSOURCE_SECOND             (BKP_RTCCR_ASOS | BKP_RTCCR_ASOE) /*!< Second pulse signal on the TAMPER pin  */
+
+/**
+  * @}
+  */
+
+/** @defgroup RTC_Interrupts_Definitions Interrupts Definitions
+  * @{
+  */
+#define RTC_IT_OW            RTC_CRH_OWIE       /*!< Overflow interrupt */
+#define RTC_IT_ALRA          RTC_CRH_ALRIE      /*!< Alarm interrupt */
+#define RTC_IT_SEC           RTC_CRH_SECIE      /*!< Second interrupt */
+#define RTC_IT_TAMP1         BKP_CSR_TPIE       /*!< TAMPER Pin interrupt enable */
+/**
+  * @}
+  */
+
+/** @defgroup RTC_Flags_Definitions Flags Definitions
+  * @{
+  */
+#define RTC_FLAG_RTOFF       RTC_CRL_RTOFF      /*!< RTC Operation OFF flag */
+#define RTC_FLAG_RSF         RTC_CRL_RSF        /*!< Registers Synchronized flag */
+#define RTC_FLAG_OW          RTC_CRL_OWF        /*!< Overflow flag */
+#define RTC_FLAG_ALRAF       RTC_CRL_ALRF       /*!< Alarm flag */
+#define RTC_FLAG_SEC         RTC_CRL_SECF       /*!< Second flag */
+#define RTC_FLAG_TAMP1F      BKP_CSR_TEF        /*!< Tamper Interrupt Flag */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Exported macro ------------------------------------------------------------*/
+/** @defgroup RTC_Exported_macros RTC Exported Macros
+  * @{
+  */
+
+/** @brief  Reset RTC handle state
+  * @param  __HANDLE__: RTC handle.
+  * @retval None
+  */
+#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1)
+#define __HAL_RTC_RESET_HANDLE_STATE(__HANDLE__) do{\
+                                                      (__HANDLE__)->State = HAL_RTC_STATE_RESET;\
+                                                      (__HANDLE__)->MspInitCallback = NULL;\
+                                                      (__HANDLE__)->MspDeInitCallback = NULL;\
+                                                     }while(0u)
+#else
+#define __HAL_RTC_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_RTC_STATE_RESET)
+#endif /* USE_HAL_RTC_REGISTER_CALLBACKS */
+
+/**
+  * @brief  Disable the write protection for RTC registers.
+  * @param  __HANDLE__: specifies the RTC handle.
+  * @retval None
+  */
+#define __HAL_RTC_WRITEPROTECTION_DISABLE(__HANDLE__)         SET_BIT((__HANDLE__)->Instance->CRL, RTC_CRL_CNF)
+
+/**
+  * @brief  Enable the write protection for RTC registers.
+  * @param  __HANDLE__: specifies the RTC handle.
+  * @retval None
+  */
+#define __HAL_RTC_WRITEPROTECTION_ENABLE(__HANDLE__)          CLEAR_BIT((__HANDLE__)->Instance->CRL, RTC_CRL_CNF)
+
+/**
+  * @brief  Enable the RTC Alarm interrupt.
+  * @param  __HANDLE__: specifies the RTC handle.
+  * @param  __INTERRUPT__: specifies the RTC Alarm interrupt sources to be enabled or disabled.
+  *          This parameter can be any combination of the following values:
+  *            @arg RTC_IT_ALRA: Alarm A interrupt
+  * @retval None
+  */
+#define __HAL_RTC_ALARM_ENABLE_IT(__HANDLE__, __INTERRUPT__)  SET_BIT((__HANDLE__)->Instance->CRH, (__INTERRUPT__))
+
+/**
+  * @brief  Disable the RTC Alarm interrupt.
+  * @param  __HANDLE__: specifies the RTC handle.
+  * @param  __INTERRUPT__: specifies the RTC Alarm interrupt sources to be enabled or disabled.
+  *         This parameter can be any combination of the following values:
+  *            @arg RTC_IT_ALRA: Alarm A interrupt
+  * @retval None
+  */
+#define __HAL_RTC_ALARM_DISABLE_IT(__HANDLE__, __INTERRUPT__) CLEAR_BIT((__HANDLE__)->Instance->CRH, (__INTERRUPT__))
+
+/**
+  * @brief  Check whether the specified RTC Alarm interrupt has been enabled or not.
+  * @param  __HANDLE__: specifies the RTC handle.
+  * @param  __INTERRUPT__: specifies the RTC Alarm interrupt sources to be checked
+  *         This parameter can be:
+  *            @arg RTC_IT_ALRA: Alarm A interrupt
+  * @retval None
+  */
+#define __HAL_RTC_ALARM_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__)     ((((((__HANDLE__)->Instance->CRH)& ((__INTERRUPT__)))) != RESET)? SET : RESET)
+
+/**
+  * @brief  Get the selected RTC Alarm's flag status.
+  * @param  __HANDLE__: specifies the RTC handle.
+  * @param  __FLAG__: specifies the RTC Alarm Flag sources to be enabled or disabled.
+  *          This parameter can be:
+  *            @arg RTC_FLAG_ALRAF
+  * @retval None
+  */
+#define __HAL_RTC_ALARM_GET_FLAG(__HANDLE__, __FLAG__)        (((((__HANDLE__)->Instance->CRL) & (__FLAG__)) != RESET)? SET : RESET)
+
+/**
+  * @brief  Check whether the specified RTC Alarm interrupt has occurred or not.
+  * @param  __HANDLE__: specifies the RTC handle.
+  * @param  __INTERRUPT__: specifies the RTC Alarm interrupt sources to check.
+  *         This parameter can be:
+  *            @arg RTC_IT_ALRA: Alarm A interrupt
+  * @retval None
+  */
+#define __HAL_RTC_ALARM_GET_IT(__HANDLE__, __INTERRUPT__)        (((((__HANDLE__)->Instance->CRL) & (__INTERRUPT__)) != RESET)? SET : RESET)
+
+/**
+  * @brief  Clear the RTC Alarm's pending flags.
+  * @param  __HANDLE__: specifies the RTC handle.
+  * @param  __FLAG__: specifies the RTC Alarm Flag sources to be enabled or disabled.
+  *         This parameter can be:
+  *            @arg RTC_FLAG_ALRAF
+  * @retval None
+  */
+#define __HAL_RTC_ALARM_CLEAR_FLAG(__HANDLE__, __FLAG__)      ((__HANDLE__)->Instance->CRL) &= ~(__FLAG__)
+
+/**
+  * @brief Enable interrupt on ALARM Exti Line 17.
+  * @retval None.
+  */
+#define __HAL_RTC_ALARM_EXTI_ENABLE_IT()                  SET_BIT(EXTI->IMR, RTC_EXTI_LINE_ALARM_EVENT)
+
+/**
+  * @brief Disable interrupt on ALARM Exti Line 17.
+  * @retval None.
+  */
+#define __HAL_RTC_ALARM_EXTI_DISABLE_IT()                 CLEAR_BIT(EXTI->IMR, RTC_EXTI_LINE_ALARM_EVENT)
+
+/**
+  * @brief Enable event on ALARM Exti Line 17.
+  * @retval None.
+  */
+#define __HAL_RTC_ALARM_EXTI_ENABLE_EVENT()               SET_BIT(EXTI->EMR, RTC_EXTI_LINE_ALARM_EVENT)
+
+/**
+  * @brief Disable event on ALARM Exti Line 17.
+  * @retval None.
+  */
+#define __HAL_RTC_ALARM_EXTI_DISABLE_EVENT()              CLEAR_BIT(EXTI->EMR, RTC_EXTI_LINE_ALARM_EVENT)
+
+
+/**
+  * @brief  ALARM EXTI line configuration: set falling edge trigger.
+  * @retval None.
+  */
+#define __HAL_RTC_ALARM_EXTI_ENABLE_FALLING_EDGE()        SET_BIT(EXTI->FTSR, RTC_EXTI_LINE_ALARM_EVENT)
+
+
+/**
+  * @brief Disable the ALARM Extended Interrupt Falling Trigger.
+  * @retval None.
+  */
+#define __HAL_RTC_ALARM_EXTI_DISABLE_FALLING_EDGE()       CLEAR_BIT(EXTI->FTSR, RTC_EXTI_LINE_ALARM_EVENT)
+
+
+/**
+  * @brief  ALARM EXTI line configuration: set rising edge trigger.
+  * @retval None.
+  */
+#define __HAL_RTC_ALARM_EXTI_ENABLE_RISING_EDGE()         SET_BIT(EXTI->RTSR, RTC_EXTI_LINE_ALARM_EVENT)
+
+/**
+  * @brief Disable the ALARM Extended Interrupt Rising Trigger.
+  * This parameter can be:
+  * @retval None.
+  */
+#define __HAL_RTC_ALARM_EXTI_DISABLE_RISING_EDGE()        CLEAR_BIT(EXTI->RTSR, RTC_EXTI_LINE_ALARM_EVENT)
+
+/**
+  * @brief  ALARM EXTI line configuration: set rising & falling edge trigger.
+  * @retval None.
+  */
+#define __HAL_RTC_ALARM_EXTI_ENABLE_RISING_FALLING_EDGE()      \
+do{                                                            \
+    __HAL_RTC_ALARM_EXTI_ENABLE_RISING_EDGE();                 \
+    __HAL_RTC_ALARM_EXTI_ENABLE_FALLING_EDGE();                \
+  } while(0U)
+
+/**
+  * @brief Disable the ALARM Extended Interrupt Rising & Falling Trigger.
+  * This parameter can be:
+  * @retval None.
+  */
+#define __HAL_RTC_ALARM_EXTI_DISABLE_RISING_FALLING_EDGE()      \
+do{                                                             \
+    __HAL_RTC_ALARM_EXTI_DISABLE_RISING_EDGE();                 \
+    __HAL_RTC_ALARM_EXTI_DISABLE_FALLING_EDGE();                \
+  } while(0U)
+
+/**
+  * @brief Check whether the specified ALARM EXTI interrupt flag is set or not.
+  * @retval EXTI ALARM Line Status.
+  */
+#define __HAL_RTC_ALARM_EXTI_GET_FLAG()                   (EXTI->PR & (RTC_EXTI_LINE_ALARM_EVENT))
+
+/**
+  * @brief Clear the ALARM EXTI flag.
+  * @retval None.
+  */
+#define __HAL_RTC_ALARM_EXTI_CLEAR_FLAG()                 (EXTI->PR = (RTC_EXTI_LINE_ALARM_EVENT))
+
+/**
+  * @brief Generate a Software interrupt on selected EXTI line.
+  * @retval None.
+  */
+#define __HAL_RTC_ALARM_EXTI_GENERATE_SWIT()              SET_BIT(EXTI->SWIER, RTC_EXTI_LINE_ALARM_EVENT)
+/**
+  * @}
+  */
+
+/* Include RTC HAL Extension module */
+#include "stm32f1xx_hal_rtc_ex.h"
+
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup RTC_Exported_Functions
+  * @{
+  */
+
+
+/* Initialization and de-initialization functions  ****************************/
+/** @addtogroup RTC_Exported_Functions_Group1
+  * @{
+  */
+HAL_StatusTypeDef HAL_RTC_Init(RTC_HandleTypeDef *hrtc);
+HAL_StatusTypeDef HAL_RTC_DeInit(RTC_HandleTypeDef *hrtc);
+void              HAL_RTC_MspInit(RTC_HandleTypeDef *hrtc);
+void              HAL_RTC_MspDeInit(RTC_HandleTypeDef *hrtc);
+
+/* Callbacks Register/UnRegister functions  ***********************************/
+#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1)
+HAL_StatusTypeDef HAL_RTC_RegisterCallback(RTC_HandleTypeDef *hrtc, HAL_RTC_CallbackIDTypeDef CallbackID, pRTC_CallbackTypeDef pCallback);
+HAL_StatusTypeDef HAL_RTC_UnRegisterCallback(RTC_HandleTypeDef *hrtc, HAL_RTC_CallbackIDTypeDef CallbackID);
+#endif /* USE_HAL_RTC_REGISTER_CALLBACKS */
+/**
+  * @}
+  */
+
+/* RTC Time and Date functions ************************************************/
+/** @addtogroup RTC_Exported_Functions_Group2
+  * @{
+  */
+HAL_StatusTypeDef HAL_RTC_SetTime(RTC_HandleTypeDef *hrtc, RTC_TimeTypeDef *sTime, uint32_t Format);
+HAL_StatusTypeDef HAL_RTC_GetTime(RTC_HandleTypeDef *hrtc, RTC_TimeTypeDef *sTime, uint32_t Format);
+HAL_StatusTypeDef HAL_RTC_SetDate(RTC_HandleTypeDef *hrtc, RTC_DateTypeDef *sDate, uint32_t Format);
+HAL_StatusTypeDef HAL_RTC_GetDate(RTC_HandleTypeDef *hrtc, RTC_DateTypeDef *sDate, uint32_t Format);
+/**
+  * @}
+  */
+
+/* RTC Alarm functions ********************************************************/
+/** @addtogroup RTC_Exported_Functions_Group3
+  * @{
+  */
+HAL_StatusTypeDef HAL_RTC_SetAlarm(RTC_HandleTypeDef *hrtc, RTC_AlarmTypeDef *sAlarm, uint32_t Format);
+HAL_StatusTypeDef HAL_RTC_SetAlarm_IT(RTC_HandleTypeDef *hrtc, RTC_AlarmTypeDef *sAlarm, uint32_t Format);
+HAL_StatusTypeDef HAL_RTC_DeactivateAlarm(RTC_HandleTypeDef *hrtc, uint32_t Alarm);
+HAL_StatusTypeDef HAL_RTC_GetAlarm(RTC_HandleTypeDef *hrtc, RTC_AlarmTypeDef *sAlarm, uint32_t Alarm, uint32_t Format);
+void              HAL_RTC_AlarmIRQHandler(RTC_HandleTypeDef *hrtc);
+HAL_StatusTypeDef HAL_RTC_PollForAlarmAEvent(RTC_HandleTypeDef *hrtc, uint32_t Timeout);
+void              HAL_RTC_AlarmAEventCallback(RTC_HandleTypeDef *hrtc);
+/**
+  * @}
+  */
+
+/* Peripheral State functions *************************************************/
+/** @addtogroup RTC_Exported_Functions_Group4
+  * @{
+  */
+HAL_RTCStateTypeDef HAL_RTC_GetState(RTC_HandleTypeDef *hrtc);
+/**
+  * @}
+  */
+
+/* Peripheral Control functions ***********************************************/
+/** @addtogroup RTC_Exported_Functions_Group5
+  * @{
+  */
+HAL_StatusTypeDef   HAL_RTC_WaitForSynchro(RTC_HandleTypeDef *hrtc);
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F1xx_HAL_RTC_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_rtc_ex.h

@@ -0,0 +1,412 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_hal_rtc_ex.h
+  * @author  MCD Application Team
+  * @brief   Header file of RTC HAL Extension module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F1xx_HAL_RTC_EX_H
+#define __STM32F1xx_HAL_RTC_EX_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_hal_def.h"
+
+/** @addtogroup STM32F1xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup RTCEx
+  * @{
+  */
+
+/** @addtogroup RTCEx_Private_Macros
+  * @{
+  */
+
+/** @defgroup RTCEx_Alias_For_Legacy Alias define maintained for legacy
+  * @{
+  */
+#define HAL_RTCEx_TamperTimeStampIRQHandler HAL_RTCEx_TamperIRQHandler
+
+/**
+  * @}
+  */
+
+/** @defgroup RTCEx_IS_RTC_Definitions Private macros to check input parameters
+  * @{
+  */
+#define IS_RTC_TAMPER(__TAMPER__) ((__TAMPER__) == RTC_TAMPER_1)
+
+#define IS_RTC_TAMPER_TRIGGER(__TRIGGER__)  (((__TRIGGER__) == RTC_TAMPERTRIGGER_LOWLEVEL) || \
+                                             ((__TRIGGER__) == RTC_TAMPERTRIGGER_HIGHLEVEL))
+
+#if RTC_BKP_NUMBER > 10U
+#define IS_RTC_BKP(BKP)                   (((BKP) <= (uint32_t)RTC_BKP_DR10) || (((BKP) >= (uint32_t)RTC_BKP_DR11) && ((BKP) <= (uint32_t)RTC_BKP_DR42)))
+#else
+#define IS_RTC_BKP(BKP)                   ((BKP) <= (uint32_t)RTC_BKP_NUMBER)
+#endif
+#define IS_RTC_SMOOTH_CALIB_MINUS(__VALUE__) ((__VALUE__) <= 0x0000007FU)
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Exported types ------------------------------------------------------------*/
+/** @defgroup RTCEx_Exported_Types RTCEx Exported Types
+  * @{
+  */
+/**
+  * @brief  RTC Tamper structure definition
+  */
+typedef struct
+{
+  uint32_t Tamper;                      /*!< Specifies the Tamper Pin.
+                                             This parameter can be a value of @ref  RTCEx_Tamper_Pins_Definitions */
+
+  uint32_t Trigger;                     /*!< Specifies the Tamper Trigger.
+                                             This parameter can be a value of @ref  RTCEx_Tamper_Trigger_Definitions */
+
+} RTC_TamperTypeDef;
+
+/**
+  * @}
+  */
+
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup RTCEx_Exported_Constants RTCEx Exported Constants
+  * @{
+  */
+
+/** @defgroup RTCEx_Tamper_Pins_Definitions Tamper Pins Definitions
+  * @{
+  */
+#define RTC_TAMPER_1                        BKP_CR_TPE            /*!< Select tamper to be enabled (mainly for legacy purposes) */
+
+/**
+  * @}
+  */
+
+/** @defgroup RTCEx_Tamper_Trigger_Definitions Tamper Trigger Definitions
+  * @{
+  */
+#define RTC_TAMPERTRIGGER_LOWLEVEL          BKP_CR_TPAL           /*!< A high level on the TAMPER pin resets all data backup registers (if TPE bit is set) */
+#define RTC_TAMPERTRIGGER_HIGHLEVEL         0x00000000U           /*!< A low level on the TAMPER pin resets all data backup registers (if TPE bit is set) */
+
+/**
+  * @}
+  */
+
+/** @defgroup RTCEx_Backup_Registers_Definitions Backup Registers Definitions
+  * @{
+  */
+#if RTC_BKP_NUMBER > 0U
+#define RTC_BKP_DR1                         0x00000001U
+#define RTC_BKP_DR2                         0x00000002U
+#define RTC_BKP_DR3                         0x00000003U
+#define RTC_BKP_DR4                         0x00000004U
+#define RTC_BKP_DR5                         0x00000005U
+#define RTC_BKP_DR6                         0x00000006U
+#define RTC_BKP_DR7                         0x00000007U
+#define RTC_BKP_DR8                         0x00000008U
+#define RTC_BKP_DR9                         0x00000009U
+#define RTC_BKP_DR10                        0x0000000AU
+#endif /* RTC_BKP_NUMBER > 0 */
+
+#if RTC_BKP_NUMBER > 10U
+#define RTC_BKP_DR11                        0x00000010U
+#define RTC_BKP_DR12                        0x00000011U
+#define RTC_BKP_DR13                        0x00000012U
+#define RTC_BKP_DR14                        0x00000013U
+#define RTC_BKP_DR15                        0x00000014U
+#define RTC_BKP_DR16                        0x00000015U
+#define RTC_BKP_DR17                        0x00000016U
+#define RTC_BKP_DR18                        0x00000017U
+#define RTC_BKP_DR19                        0x00000018U
+#define RTC_BKP_DR20                        0x00000019U
+#define RTC_BKP_DR21                        0x0000001AU
+#define RTC_BKP_DR22                        0x0000001BU
+#define RTC_BKP_DR23                        0x0000001CU
+#define RTC_BKP_DR24                        0x0000001DU
+#define RTC_BKP_DR25                        0x0000001EU
+#define RTC_BKP_DR26                        0x0000001FU
+#define RTC_BKP_DR27                        0x00000020U
+#define RTC_BKP_DR28                        0x00000021U
+#define RTC_BKP_DR29                        0x00000022U
+#define RTC_BKP_DR30                        0x00000023U
+#define RTC_BKP_DR31                        0x00000024U
+#define RTC_BKP_DR32                        0x00000025U
+#define RTC_BKP_DR33                        0x00000026U
+#define RTC_BKP_DR34                        0x00000027U
+#define RTC_BKP_DR35                        0x00000028U
+#define RTC_BKP_DR36                        0x00000029U
+#define RTC_BKP_DR37                        0x0000002AU
+#define RTC_BKP_DR38                        0x0000002BU
+#define RTC_BKP_DR39                        0x0000002CU
+#define RTC_BKP_DR40                        0x0000002DU
+#define RTC_BKP_DR41                        0x0000002EU
+#define RTC_BKP_DR42                        0x0000002FU
+#endif /* RTC_BKP_NUMBER > 10 */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Exported macro ------------------------------------------------------------*/
+/** @defgroup RTCEx_Exported_Macros RTCEx Exported Macros
+  * @{
+  */
+
+/**
+  * @brief  Enable the RTC Tamper interrupt.
+  * @param  __HANDLE__: specifies the RTC handle.
+  * @param  __INTERRUPT__: specifies the RTC Tamper interrupt sources to be enabled
+  *          This parameter can be any combination of the following values:
+  *            @arg RTC_IT_TAMP1: Tamper A interrupt
+  * @retval None
+  */
+#define __HAL_RTC_TAMPER_ENABLE_IT(__HANDLE__, __INTERRUPT__) SET_BIT(BKP->CSR, (__INTERRUPT__))
+
+/**
+  * @brief  Disable the RTC Tamper interrupt.
+  * @param  __HANDLE__: specifies the RTC handle.
+  * @param  __INTERRUPT__: specifies the RTC Tamper interrupt sources to be disabled.
+  *         This parameter can be any combination of the following values:
+  *            @arg RTC_IT_TAMP1: Tamper A interrupt
+  * @retval None
+  */
+#define __HAL_RTC_TAMPER_DISABLE_IT(__HANDLE__, __INTERRUPT__)  CLEAR_BIT(BKP->CSR, (__INTERRUPT__))
+
+/**
+  * @brief  Check whether the specified RTC Tamper interrupt has been enabled or not.
+  * @param  __HANDLE__: specifies the RTC handle.
+  * @param  __INTERRUPT__: specifies the RTC Tamper interrupt sources to be checked.
+  *         This parameter can be:
+  *            @arg  RTC_IT_TAMP1
+  * @retval None
+  */
+#define __HAL_RTC_TAMPER_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__)    ((((BKP->CSR) & ((__INTERRUPT__))) != RESET)? SET : RESET)
+
+/**
+  * @brief  Get the selected RTC Tamper's flag status.
+  * @param  __HANDLE__: specifies the RTC handle.
+  * @param  __FLAG__: specifies the RTC Tamper Flag sources to be enabled or disabled.
+  *         This parameter can be:
+  *            @arg RTC_FLAG_TAMP1F
+  * @retval None
+  */
+#define __HAL_RTC_TAMPER_GET_FLAG(__HANDLE__, __FLAG__)       ((((BKP->CSR) & (__FLAG__)) != RESET)? SET : RESET)
+
+/**
+  * @brief  Get the selected RTC Tamper's flag status.
+  * @param  __HANDLE__: specifies the RTC handle.
+  * @param  __INTERRUPT__: specifies the RTC Tamper interrupt sources to be checked.
+  *         This parameter can be:
+  *            @arg  RTC_IT_TAMP1
+  * @retval None
+  */
+#define __HAL_RTC_TAMPER_GET_IT(__HANDLE__, __INTERRUPT__)       ((((BKP->CSR) & (BKP_CSR_TEF)) != RESET)? SET : RESET)
+
+/**
+  * @brief  Clear the RTC Tamper's pending flags.
+  * @param  __HANDLE__: specifies the RTC handle.
+  * @param  __FLAG__: specifies the RTC Tamper Flag sources to be enabled or disabled.
+  *         This parameter can be:
+  *            @arg RTC_FLAG_TAMP1F
+  * @retval None
+  */
+#define __HAL_RTC_TAMPER_CLEAR_FLAG(__HANDLE__, __FLAG__)     SET_BIT(BKP->CSR, BKP_CSR_CTE | BKP_CSR_CTI)
+
+/**
+  * @brief  Enable the RTC Second interrupt.
+  * @param  __HANDLE__: specifies the RTC handle.
+  * @param  __INTERRUPT__: specifies the RTC Second interrupt sources to be enabled
+  *          This parameter can be any combination of the following values:
+  *            @arg RTC_IT_SEC: Second A interrupt
+  * @retval None
+  */
+#define __HAL_RTC_SECOND_ENABLE_IT(__HANDLE__, __INTERRUPT__)  SET_BIT((__HANDLE__)->Instance->CRH, (__INTERRUPT__))
+
+/**
+  * @brief  Disable the RTC Second interrupt.
+  * @param  __HANDLE__: specifies the RTC handle.
+  * @param  __INTERRUPT__: specifies the RTC Second interrupt sources to be disabled.
+  *         This parameter can be any combination of the following values:
+  *            @arg RTC_IT_SEC: Second A interrupt
+  * @retval None
+  */
+#define __HAL_RTC_SECOND_DISABLE_IT(__HANDLE__, __INTERRUPT__) CLEAR_BIT((__HANDLE__)->Instance->CRH, (__INTERRUPT__))
+
+/**
+  * @brief  Check whether the specified RTC Second interrupt has occurred or not.
+  * @param  __HANDLE__: specifies the RTC handle.
+  * @param  __INTERRUPT__: specifies the RTC Second interrupt sources to be enabled or disabled.
+  *         This parameter can be:
+  *            @arg RTC_IT_SEC: Second A interrupt
+  * @retval None
+  */
+#define __HAL_RTC_SECOND_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__)      ((((((__HANDLE__)->Instance->CRH)& ((__INTERRUPT__)))) != RESET)? SET : RESET)
+
+/**
+  * @brief  Get the selected RTC Second's flag status.
+  * @param  __HANDLE__: specifies the RTC handle.
+  * @param  __FLAG__: specifies the RTC Second Flag sources to be enabled or disabled.
+  *          This parameter can be:
+  *            @arg RTC_FLAG_SEC
+  * @retval None
+  */
+#define __HAL_RTC_SECOND_GET_FLAG(__HANDLE__, __FLAG__)        (((((__HANDLE__)->Instance->CRL) & (__FLAG__)) != RESET)? SET : RESET)
+
+/**
+  * @brief  Clear the RTC Second's pending flags.
+  * @param  __HANDLE__: specifies the RTC handle.
+  * @param  __FLAG__: specifies the RTC Second Flag sources to be enabled or disabled.
+  *         This parameter can be:
+  *            @arg RTC_FLAG_SEC
+  * @retval None
+  */
+#define __HAL_RTC_SECOND_CLEAR_FLAG(__HANDLE__, __FLAG__)      ((__HANDLE__)->Instance->CRL) &= ~(__FLAG__)
+
+/**
+  * @brief  Enable the RTC Overflow interrupt.
+  * @param  __HANDLE__: specifies the RTC handle.
+  * @param  __INTERRUPT__: specifies the RTC Overflow interrupt sources to be enabled
+  *          This parameter can be any combination of the following values:
+  *            @arg RTC_IT_OW: Overflow A interrupt
+  * @retval None
+  */
+#define __HAL_RTC_OVERFLOW_ENABLE_IT(__HANDLE__, __INTERRUPT__)  SET_BIT((__HANDLE__)->Instance->CRH, (__INTERRUPT__))
+
+/**
+  * @brief  Disable the RTC Overflow interrupt.
+  * @param  __HANDLE__: specifies the RTC handle.
+  * @param  __INTERRUPT__: specifies the RTC Overflow interrupt sources to be disabled.
+  *         This parameter can be any combination of the following values:
+  *            @arg RTC_IT_OW: Overflow A interrupt
+  * @retval None
+  */
+#define __HAL_RTC_OVERFLOW_DISABLE_IT(__HANDLE__, __INTERRUPT__) CLEAR_BIT((__HANDLE__)->Instance->CRH, (__INTERRUPT__))
+
+/**
+  * @brief  Check whether the specified RTC Overflow interrupt has occurred or not.
+  * @param  __HANDLE__: specifies the RTC handle.
+  * @param  __INTERRUPT__: specifies the RTC Overflow interrupt sources to be enabled or disabled.
+  *         This parameter can be:
+  *            @arg RTC_IT_OW: Overflow A interrupt
+  * @retval None
+  */
+#define __HAL_RTC_OVERFLOW_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__)    ((((((__HANDLE__)->Instance->CRH)& ((__INTERRUPT__))) ) != RESET)? SET : RESET)
+
+/**
+  * @brief  Get the selected RTC Overflow's flag status.
+  * @param  __HANDLE__: specifies the RTC handle.
+  * @param  __FLAG__: specifies the RTC Overflow Flag sources to be enabled or disabled.
+  *          This parameter can be:
+  *            @arg RTC_FLAG_OW
+  * @retval None
+  */
+#define __HAL_RTC_OVERFLOW_GET_FLAG(__HANDLE__, __FLAG__)        (((((__HANDLE__)->Instance->CRL) & (__FLAG__)) != RESET)? SET : RESET)
+
+/**
+  * @brief  Clear the RTC Overflow's pending flags.
+  * @param  __HANDLE__: specifies the RTC handle.
+  * @param  __FLAG__: specifies the RTC Overflow Flag sources to be enabled or disabled.
+  *         This parameter can be:
+  *            @arg RTC_FLAG_OW
+  * @retval None
+  */
+#define __HAL_RTC_OVERFLOW_CLEAR_FLAG(__HANDLE__, __FLAG__)      ((__HANDLE__)->Instance->CRL) = ~(__FLAG__)
+
+/**
+  * @}
+  */
+
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup RTCEx_Exported_Functions
+  * @{
+  */
+
+/* RTC Tamper functions *****************************************/
+/** @addtogroup RTCEx_Exported_Functions_Group1
+  * @{
+  */
+HAL_StatusTypeDef HAL_RTCEx_SetTamper(RTC_HandleTypeDef *hrtc, RTC_TamperTypeDef *sTamper);
+HAL_StatusTypeDef HAL_RTCEx_SetTamper_IT(RTC_HandleTypeDef *hrtc, RTC_TamperTypeDef *sTamper);
+HAL_StatusTypeDef HAL_RTCEx_DeactivateTamper(RTC_HandleTypeDef *hrtc, uint32_t Tamper);
+void              HAL_RTCEx_TamperIRQHandler(RTC_HandleTypeDef *hrtc);
+void              HAL_RTCEx_Tamper1EventCallback(RTC_HandleTypeDef *hrtc);
+HAL_StatusTypeDef HAL_RTCEx_PollForTamper1Event(RTC_HandleTypeDef *hrtc, uint32_t Timeout);
+
+/**
+  * @}
+  */
+
+/* RTC Second functions *****************************************/
+/** @addtogroup RTCEx_Exported_Functions_Group2
+  * @{
+  */
+HAL_StatusTypeDef HAL_RTCEx_SetSecond_IT(RTC_HandleTypeDef *hrtc);
+HAL_StatusTypeDef HAL_RTCEx_DeactivateSecond(RTC_HandleTypeDef *hrtc);
+void              HAL_RTCEx_RTCIRQHandler(RTC_HandleTypeDef *hrtc);
+void              HAL_RTCEx_RTCEventCallback(RTC_HandleTypeDef *hrtc);
+void              HAL_RTCEx_RTCEventErrorCallback(RTC_HandleTypeDef *hrtc);
+
+/**
+  * @}
+  */
+
+/* Extension Control functions ************************************************/
+/** @addtogroup RTCEx_Exported_Functions_Group3
+  * @{
+  */
+void              HAL_RTCEx_BKUPWrite(RTC_HandleTypeDef *hrtc, uint32_t BackupRegister, uint32_t Data);
+uint32_t          HAL_RTCEx_BKUPRead(RTC_HandleTypeDef *hrtc, uint32_t BackupRegister);
+
+HAL_StatusTypeDef HAL_RTCEx_SetSmoothCalib(RTC_HandleTypeDef *hrtc, uint32_t SmoothCalibPeriod, uint32_t SmoothCalibPlusPulses, uint32_t SmouthCalibMinusPulsesValue);
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F1xx_HAL_RTC_EX_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_sd.h

@@ -0,0 +1,761 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_hal_sd.h
+  * @author  MCD Application Team
+  * @brief   Header file of SD HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2018 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                       opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */ 
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef STM32F1xx_HAL_SD_H
+#define STM32F1xx_HAL_SD_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+#if defined(SDIO)
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_ll_sdmmc.h"
+
+/** @addtogroup STM32F1xx_HAL_Driver
+  * @{
+  */
+
+/** @defgroup SD SD
+  * @brief SD HAL module driver
+  * @{
+  */ 
+
+/* Exported types ------------------------------------------------------------*/ 
+/** @defgroup SD_Exported_Types SD Exported Types
+  * @{
+  */
+
+/** @defgroup SD_Exported_Types_Group1 SD State enumeration structure
+  * @{
+  */   
+typedef enum
+{
+  HAL_SD_STATE_RESET                  = 0x00000000U,  /*!< SD not yet initialized or disabled  */
+  HAL_SD_STATE_READY                  = 0x00000001U,  /*!< SD initialized and ready for use    */
+  HAL_SD_STATE_TIMEOUT                = 0x00000002U,  /*!< SD Timeout state                    */
+  HAL_SD_STATE_BUSY                   = 0x00000003U,  /*!< SD process ongoing                  */
+  HAL_SD_STATE_PROGRAMMING            = 0x00000004U,  /*!< SD Programming State                */
+  HAL_SD_STATE_RECEIVING              = 0x00000005U,  /*!< SD Receiving State                  */
+  HAL_SD_STATE_TRANSFER               = 0x00000006U,  /*!< SD Transfer State                  */
+  HAL_SD_STATE_ERROR                  = 0x0000000FU   /*!< SD is in error state                */
+}HAL_SD_StateTypeDef;
+/** 
+  * @}
+  */
+
+/** @defgroup SD_Exported_Types_Group2 SD Card State enumeration structure
+  * @{
+  */   
+typedef uint32_t HAL_SD_CardStateTypeDef;
+
+#define HAL_SD_CARD_READY          0x00000001U  /*!< Card state is ready                     */
+#define HAL_SD_CARD_IDENTIFICATION 0x00000002U  /*!< Card is in identification state         */
+#define HAL_SD_CARD_STANDBY        0x00000003U  /*!< Card is in standby state                */
+#define HAL_SD_CARD_TRANSFER       0x00000004U  /*!< Card is in transfer state               */
+#define HAL_SD_CARD_SENDING        0x00000005U  /*!< Card is sending an operation            */
+#define HAL_SD_CARD_RECEIVING      0x00000006U  /*!< Card is receiving operation information */
+#define HAL_SD_CARD_PROGRAMMING    0x00000007U  /*!< Card is in programming state            */
+#define HAL_SD_CARD_DISCONNECTED   0x00000008U  /*!< Card is disconnected                    */
+#define HAL_SD_CARD_ERROR          0x000000FFU  /*!< Card response Error                     */
+/** 
+  * @}
+  */
+
+/** @defgroup SD_Exported_Types_Group3 SD Handle Structure definition   
+  * @{
+  */
+#define SD_InitTypeDef      SDIO_InitTypeDef 
+#define SD_TypeDef          SDIO_TypeDef
+
+/** 
+  * @brief  SD Card Information Structure definition
+  */ 
+typedef struct
+{
+  uint32_t CardType;                     /*!< Specifies the card Type                         */
+  
+  uint32_t CardVersion;                  /*!< Specifies the card version                      */
+
+  uint32_t Class;                        /*!< Specifies the class of the card class           */
+
+  uint32_t RelCardAdd;                   /*!< Specifies the Relative Card Address             */
+  
+  uint32_t BlockNbr;                     /*!< Specifies the Card Capacity in blocks           */
+
+  uint32_t BlockSize;                    /*!< Specifies one block size in bytes               */
+  
+  uint32_t LogBlockNbr;                  /*!< Specifies the Card logical Capacity in blocks   */
+
+  uint32_t LogBlockSize;                 /*!< Specifies logical block size in bytes           */
+
+}HAL_SD_CardInfoTypeDef;
+
+/** 
+  * @brief  SD handle Structure definition
+  */ 
+#if defined (USE_HAL_SD_REGISTER_CALLBACKS) && (USE_HAL_SD_REGISTER_CALLBACKS == 1U)
+typedef struct __SD_HandleTypeDef
+#else
+typedef struct
+#endif /* USE_HAL_SD_REGISTER_CALLBACKS */
+{
+  SD_TypeDef                   *Instance;        /*!< SD registers base address           */
+  
+  SD_InitTypeDef               Init;             /*!< SD required parameters              */
+  
+  HAL_LockTypeDef              Lock;             /*!< SD locking object                   */
+  
+  uint8_t                      *pTxBuffPtr;      /*!< Pointer to SD Tx transfer Buffer    */
+
+  uint32_t                     TxXferSize;       /*!< SD Tx Transfer size                 */
+
+  uint8_t                      *pRxBuffPtr;      /*!< Pointer to SD Rx transfer Buffer    */
+
+  uint32_t                     RxXferSize;       /*!< SD Rx Transfer size                 */
+  
+  __IO uint32_t                Context;          /*!< SD transfer context                 */
+ 
+  __IO HAL_SD_StateTypeDef     State;            /*!< SD card State                       */
+  
+  __IO uint32_t                ErrorCode;        /*!< SD Card Error codes                 */  
+ 
+  DMA_HandleTypeDef            *hdmatx;          /*!< SD Tx DMA handle parameters         */
+
+  DMA_HandleTypeDef            *hdmarx;          /*!< SD Rx DMA handle parameters         */
+  
+  HAL_SD_CardInfoTypeDef       SdCard;           /*!< SD Card information                 */
+  
+  uint32_t                     CSD[4];           /*!< SD card specific data table         */
+  
+  uint32_t                     CID[4];           /*!< SD card identification number table */
+  
+#if defined (USE_HAL_SD_REGISTER_CALLBACKS) && (USE_HAL_SD_REGISTER_CALLBACKS == 1U)
+  void (* TxCpltCallback)                 (struct __SD_HandleTypeDef *hsd);
+  void (* RxCpltCallback)                 (struct __SD_HandleTypeDef *hsd);
+  void (* ErrorCallback)                  (struct __SD_HandleTypeDef *hsd);
+  void (* AbortCpltCallback)              (struct __SD_HandleTypeDef *hsd);
+
+  void (* MspInitCallback)                (struct __SD_HandleTypeDef *hsd);
+  void (* MspDeInitCallback)              (struct __SD_HandleTypeDef *hsd);
+#endif /* USE_HAL_SD_REGISTER_CALLBACKS */
+}SD_HandleTypeDef;
+
+/** 
+  * @}
+  */
+
+/** @defgroup SD_Exported_Types_Group4 Card Specific Data: CSD Register 
+  * @{
+  */
+typedef struct
+{
+  __IO uint8_t  CSDStruct;            /*!< CSD structure                         */
+  __IO uint8_t  SysSpecVersion;       /*!< System specification version          */
+  __IO uint8_t  Reserved1;            /*!< Reserved                              */
+  __IO uint8_t  TAAC;                 /*!< Data read access time 1               */
+  __IO uint8_t  NSAC;                 /*!< Data read access time 2 in CLK cycles */
+  __IO uint8_t  MaxBusClkFrec;        /*!< Max. bus clock frequency              */
+  __IO uint16_t CardComdClasses;      /*!< Card command classes                  */
+  __IO uint8_t  RdBlockLen;           /*!< Max. read data block length           */
+  __IO uint8_t  PartBlockRead;        /*!< Partial blocks for read allowed       */
+  __IO uint8_t  WrBlockMisalign;      /*!< Write block misalignment              */
+  __IO uint8_t  RdBlockMisalign;      /*!< Read block misalignment               */
+  __IO uint8_t  DSRImpl;              /*!< DSR implemented                       */
+  __IO uint8_t  Reserved2;            /*!< Reserved                              */
+  __IO uint32_t DeviceSize;           /*!< Device Size                           */
+  __IO uint8_t  MaxRdCurrentVDDMin;   /*!< Max. read current @ VDD min           */
+  __IO uint8_t  MaxRdCurrentVDDMax;   /*!< Max. read current @ VDD max           */
+  __IO uint8_t  MaxWrCurrentVDDMin;   /*!< Max. write current @ VDD min          */
+  __IO uint8_t  MaxWrCurrentVDDMax;   /*!< Max. write current @ VDD max          */
+  __IO uint8_t  DeviceSizeMul;        /*!< Device size multiplier                */
+  __IO uint8_t  EraseGrSize;          /*!< Erase group size                      */
+  __IO uint8_t  EraseGrMul;           /*!< Erase group size multiplier           */
+  __IO uint8_t  WrProtectGrSize;      /*!< Write protect group size              */
+  __IO uint8_t  WrProtectGrEnable;    /*!< Write protect group enable            */
+  __IO uint8_t  ManDeflECC;           /*!< Manufacturer default ECC              */
+  __IO uint8_t  WrSpeedFact;          /*!< Write speed factor                    */
+  __IO uint8_t  MaxWrBlockLen;        /*!< Max. write data block length          */
+  __IO uint8_t  WriteBlockPaPartial;  /*!< Partial blocks for write allowed      */
+  __IO uint8_t  Reserved3;            /*!< Reserved                              */
+  __IO uint8_t  ContentProtectAppli;  /*!< Content protection application        */
+  __IO uint8_t  FileFormatGroup;      /*!< File format group                     */
+  __IO uint8_t  CopyFlag;             /*!< Copy flag (OTP)                       */
+  __IO uint8_t  PermWrProtect;        /*!< Permanent write protection            */
+  __IO uint8_t  TempWrProtect;        /*!< Temporary write protection            */
+  __IO uint8_t  FileFormat;           /*!< File format                           */
+  __IO uint8_t  ECC;                  /*!< ECC code                              */
+  __IO uint8_t  CSD_CRC;              /*!< CSD CRC                               */
+  __IO uint8_t  Reserved4;            /*!< Always 1                              */
+}HAL_SD_CardCSDTypeDef;
+/** 
+  * @}
+  */
+
+/** @defgroup SD_Exported_Types_Group5 Card Identification Data: CID Register
+  * @{
+  */
+typedef struct
+{
+  __IO uint8_t  ManufacturerID;  /*!< Manufacturer ID       */
+  __IO uint16_t OEM_AppliID;     /*!< OEM/Application ID    */
+  __IO uint32_t ProdName1;       /*!< Product Name part1    */
+  __IO uint8_t  ProdName2;       /*!< Product Name part2    */
+  __IO uint8_t  ProdRev;         /*!< Product Revision      */
+  __IO uint32_t ProdSN;          /*!< Product Serial Number */
+  __IO uint8_t  Reserved1;       /*!< Reserved1             */
+  __IO uint16_t ManufactDate;    /*!< Manufacturing Date    */
+  __IO uint8_t  CID_CRC;         /*!< CID CRC               */
+  __IO uint8_t  Reserved2;       /*!< Always 1              */
+
+}HAL_SD_CardCIDTypeDef;
+/** 
+  * @}
+  */
+
+/** @defgroup SD_Exported_Types_Group6 SD Card Status returned by ACMD13 
+  * @{
+  */
+typedef struct
+{
+  __IO uint8_t  DataBusWidth;           /*!< Shows the currently defined data bus width                 */
+  __IO uint8_t  SecuredMode;            /*!< Card is in secured mode of operation                       */
+  __IO uint16_t CardType;               /*!< Carries information about card type                        */
+  __IO uint32_t ProtectedAreaSize;      /*!< Carries information about the capacity of protected area   */
+  __IO uint8_t  SpeedClass;             /*!< Carries information about the speed class of the card      */
+  __IO uint8_t  PerformanceMove;        /*!< Carries information about the card's performance move      */
+  __IO uint8_t  AllocationUnitSize;     /*!< Carries information about the card's allocation unit size  */
+  __IO uint16_t EraseSize;              /*!< Determines the number of AUs to be erased in one operation */
+  __IO uint8_t  EraseTimeout;           /*!< Determines the timeout for any number of AU erase          */
+  __IO uint8_t  EraseOffset;            /*!< Carries information about the erase offset                 */
+
+}HAL_SD_CardStatusTypeDef;
+/** 
+  * @}
+  */
+
+#if defined (USE_HAL_SD_REGISTER_CALLBACKS) && (USE_HAL_SD_REGISTER_CALLBACKS == 1U)
+/** @defgroup SD_Exported_Types_Group7 SD Callback ID enumeration definition 
+  * @{
+  */
+typedef enum
+{
+  HAL_SD_TX_CPLT_CB_ID                 = 0x00U,  /*!< SD Tx Complete Callback ID                     */
+  HAL_SD_RX_CPLT_CB_ID                 = 0x01U,  /*!< SD Rx Complete Callback ID                     */
+  HAL_SD_ERROR_CB_ID                   = 0x02U,  /*!< SD Error Callback ID                           */
+  HAL_SD_ABORT_CB_ID                   = 0x03U,  /*!< SD Abort Callback ID                           */
+
+  HAL_SD_MSP_INIT_CB_ID                = 0x10U,  /*!< SD MspInit Callback ID                         */
+  HAL_SD_MSP_DEINIT_CB_ID              = 0x11U   /*!< SD MspDeInit Callback ID                       */
+}HAL_SD_CallbackIDTypeDef;
+/** 
+  * @}
+  */
+
+/** @defgroup SD_Exported_Types_Group8 SD Callback pointer definition 
+  * @{
+  */
+typedef void (*pSD_CallbackTypeDef)           (SD_HandleTypeDef *hsd);
+/** 
+  * @}
+  */
+#endif /* USE_HAL_SD_REGISTER_CALLBACKS */
+/** 
+  * @}
+  */
+
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup SD_Exported_Constants Exported Constants
+  * @{
+  */
+
+#define BLOCKSIZE   512U /*!< Block size is 512 bytes */
+
+/** @defgroup SD_Exported_Constansts_Group1 SD Error status enumeration Structure definition 
+  * @{
+  */  
+#define HAL_SD_ERROR_NONE                     SDMMC_ERROR_NONE                    /*!< No error                                                      */
+#define HAL_SD_ERROR_CMD_CRC_FAIL             SDMMC_ERROR_CMD_CRC_FAIL            /*!< Command response received (but CRC check failed)              */
+#define HAL_SD_ERROR_DATA_CRC_FAIL            SDMMC_ERROR_DATA_CRC_FAIL           /*!< Data block sent/received (CRC check failed)                   */
+#define HAL_SD_ERROR_CMD_RSP_TIMEOUT          SDMMC_ERROR_CMD_RSP_TIMEOUT         /*!< Command response timeout                                      */
+#define HAL_SD_ERROR_DATA_TIMEOUT             SDMMC_ERROR_DATA_TIMEOUT            /*!< Data timeout                                                  */
+#define HAL_SD_ERROR_TX_UNDERRUN              SDMMC_ERROR_TX_UNDERRUN             /*!< Transmit FIFO underrun                                        */
+#define HAL_SD_ERROR_RX_OVERRUN               SDMMC_ERROR_RX_OVERRUN              /*!< Receive FIFO overrun                                          */
+#define HAL_SD_ERROR_ADDR_MISALIGNED          SDMMC_ERROR_ADDR_MISALIGNED         /*!< Misaligned address                                            */
+#define HAL_SD_ERROR_BLOCK_LEN_ERR            SDMMC_ERROR_BLOCK_LEN_ERR           /*!< Transferred block length is not allowed for the card or the 
+                                                                                       number of transferred bytes does not match the block length   */
+#define HAL_SD_ERROR_ERASE_SEQ_ERR            SDMMC_ERROR_ERASE_SEQ_ERR           /*!< An error in the sequence of erase command occurs              */
+#define HAL_SD_ERROR_BAD_ERASE_PARAM          SDMMC_ERROR_BAD_ERASE_PARAM         /*!< An invalid selection for erase groups                         */
+#define HAL_SD_ERROR_WRITE_PROT_VIOLATION     SDMMC_ERROR_WRITE_PROT_VIOLATION    /*!< Attempt to program a write protect block                      */
+#define HAL_SD_ERROR_LOCK_UNLOCK_FAILED       SDMMC_ERROR_LOCK_UNLOCK_FAILED      /*!< Sequence or password error has been detected in unlock 
+                                                                                       command or if there was an attempt to access a locked card    */
+#define HAL_SD_ERROR_COM_CRC_FAILED           SDMMC_ERROR_COM_CRC_FAILED          /*!< CRC check of the previous command failed                      */
+#define HAL_SD_ERROR_ILLEGAL_CMD              SDMMC_ERROR_ILLEGAL_CMD             /*!< Command is not legal for the card state                       */
+#define HAL_SD_ERROR_CARD_ECC_FAILED          SDMMC_ERROR_CARD_ECC_FAILED         /*!< Card internal ECC was applied but failed to correct the data  */
+#define HAL_SD_ERROR_CC_ERR                   SDMMC_ERROR_CC_ERR                  /*!< Internal card controller error                                */
+#define HAL_SD_ERROR_GENERAL_UNKNOWN_ERR      SDMMC_ERROR_GENERAL_UNKNOWN_ERR     /*!< General or unknown error                                      */
+#define HAL_SD_ERROR_STREAM_READ_UNDERRUN     SDMMC_ERROR_STREAM_READ_UNDERRUN    /*!< The card could not sustain data reading in stream rmode       */
+#define HAL_SD_ERROR_STREAM_WRITE_OVERRUN     SDMMC_ERROR_STREAM_WRITE_OVERRUN    /*!< The card could not sustain data programming in stream mode    */
+#define HAL_SD_ERROR_CID_CSD_OVERWRITE        SDMMC_ERROR_CID_CSD_OVERWRITE       /*!< CID/CSD overwrite error                                       */
+#define HAL_SD_ERROR_WP_ERASE_SKIP            SDMMC_ERROR_WP_ERASE_SKIP           /*!< Only partial address space was erased                         */
+#define HAL_SD_ERROR_CARD_ECC_DISABLED        SDMMC_ERROR_CARD_ECC_DISABLED       /*!< Command has been executed without using internal ECC          */
+#define HAL_SD_ERROR_ERASE_RESET              SDMMC_ERROR_ERASE_RESET             /*!< Erase sequence was cleared before executing because an out 
+                                                                                       of erase sequence command was received                        */
+#define HAL_SD_ERROR_AKE_SEQ_ERR              SDMMC_ERROR_AKE_SEQ_ERR             /*!< Error in sequence of authentication                           */
+#define HAL_SD_ERROR_INVALID_VOLTRANGE        SDMMC_ERROR_INVALID_VOLTRANGE       /*!< Error in case of invalid voltage range                        */        
+#define HAL_SD_ERROR_ADDR_OUT_OF_RANGE        SDMMC_ERROR_ADDR_OUT_OF_RANGE       /*!< Error when addressed block is out of range                    */        
+#define HAL_SD_ERROR_REQUEST_NOT_APPLICABLE   SDMMC_ERROR_REQUEST_NOT_APPLICABLE  /*!< Error when command request is not applicable                  */  
+#define HAL_SD_ERROR_PARAM                    SDMMC_ERROR_INVALID_PARAMETER       /*!< the used parameter is not valid                               */  
+#define HAL_SD_ERROR_UNSUPPORTED_FEATURE      SDMMC_ERROR_UNSUPPORTED_FEATURE     /*!< Error when feature is not insupported                         */
+#define HAL_SD_ERROR_BUSY                     SDMMC_ERROR_BUSY                    /*!< Error when transfer process is busy                           */ 
+#define HAL_SD_ERROR_DMA                      SDMMC_ERROR_DMA                     /*!< Error while DMA transfer                                      */
+#define HAL_SD_ERROR_TIMEOUT                  SDMMC_ERROR_TIMEOUT                 /*!< Timeout error                                                 */
+                                                
+#if defined (USE_HAL_SD_REGISTER_CALLBACKS) && (USE_HAL_SD_REGISTER_CALLBACKS == 1U)
+#define HAL_SD_ERROR_INVALID_CALLBACK         SDMMC_ERROR_INVALID_PARAMETER       /*!< Invalid callback error                                        */
+#endif /* USE_HAL_SD_REGISTER_CALLBACKS */
+/** 
+  * @}
+  */
+ 
+/** @defgroup SD_Exported_Constansts_Group2 SD context enumeration
+  * @{
+  */ 
+#define SD_CONTEXT_NONE                            0x00000000U   /*!< None                             */
+#define SD_CONTEXT_READ_SINGLE_BLOCK               0x00000001U   /*!< Read single block operation      */
+#define SD_CONTEXT_READ_MULTIPLE_BLOCK             0x00000002U   /*!< Read multiple blocks operation   */
+#define SD_CONTEXT_WRITE_SINGLE_BLOCK              0x00000010U   /*!< Write single block operation     */
+#define SD_CONTEXT_WRITE_MULTIPLE_BLOCK            0x00000020U   /*!< Write multiple blocks operation  */
+#define SD_CONTEXT_IT                              0x00000008U   /*!< Process in Interrupt mode        */
+#define SD_CONTEXT_DMA                             0x00000080U   /*!< Process in DMA mode              */
+
+/**
+  * @}
+  */
+
+/** @defgroup SD_Exported_Constansts_Group3 SD Supported Memory Cards
+  * @{
+  */
+#define CARD_SDSC                  0x00000000U  /*!< SD Standard Capacity <2Go                          */
+#define CARD_SDHC_SDXC             0x00000001U  /*!< SD High Capacity <32Go, SD Extended Capacity <2To  */
+#define CARD_SECURED               0x00000003U
+    
+/**
+  * @}
+  */
+
+/** @defgroup SD_Exported_Constansts_Group4 SD Supported Version
+  * @{
+  */
+#define CARD_V1_X                  0x00000000U
+#define CARD_V2_X                  0x00000001U
+/**
+  * @}
+  */
+      
+/**
+  * @}
+  */
+  
+/* Exported macro ------------------------------------------------------------*/
+/** @defgroup SD_Exported_macros SD Exported Macros
+ *  @brief macros to handle interrupts and specific clock configurations
+ * @{
+ */
+/** @brief Reset SD handle state.
+  * @param  __HANDLE__ : SD handle.
+  * @retval None
+  */
+#if defined (USE_HAL_SD_REGISTER_CALLBACKS) && (USE_HAL_SD_REGISTER_CALLBACKS == 1U)
+#define __HAL_SD_RESET_HANDLE_STATE(__HANDLE__)           do {                                              \
+                                                               (__HANDLE__)->State = HAL_SD_STATE_RESET; \
+                                                               (__HANDLE__)->MspInitCallback = NULL;       \
+                                                               (__HANDLE__)->MspDeInitCallback = NULL;     \
+                                                             } while(0)
+#else
+#define __HAL_SD_RESET_HANDLE_STATE(__HANDLE__)           ((__HANDLE__)->State = HAL_SD_STATE_RESET)
+#endif /* USE_HAL_SD_REGISTER_CALLBACKS */
+ 
+/**
+  * @brief  Enable the SD device.
+  * @retval None
+  */ 
+#define __HAL_SD_ENABLE(__HANDLE__) __SDIO_ENABLE((__HANDLE__)->Instance)
+
+/**
+  * @brief  Disable the SD device.
+  * @retval None
+  */
+#define __HAL_SD_DISABLE(__HANDLE__) __SDIO_DISABLE((__HANDLE__)->Instance)
+
+/**
+  * @brief  Enable the SDMMC DMA transfer.
+  * @retval None
+  */ 
+#define __HAL_SD_DMA_ENABLE(__HANDLE__) __SDIO_DMA_ENABLE((__HANDLE__)->Instance)
+
+/**
+  * @brief  Disable the SDMMC DMA transfer.
+  * @retval None
+  */
+#define __HAL_SD_DMA_DISABLE(__HANDLE__)  __SDIO_DMA_DISABLE((__HANDLE__)->Instance)
+ 
+/**
+  * @brief  Enable the SD device interrupt.
+  * @param  __HANDLE__: SD Handle  
+  * @param  __INTERRUPT__: specifies the SDMMC interrupt sources to be enabled.
+  *         This parameter can be one or a combination of the following values:
+  *            @arg SDIO_IT_CCRCFAIL: Command response received (CRC check failed) interrupt
+  *            @arg SDIO_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt
+  *            @arg SDIO_IT_CTIMEOUT: Command response timeout interrupt
+  *            @arg SDIO_IT_DTIMEOUT: Data timeout interrupt
+  *            @arg SDIO_IT_TXUNDERR: Transmit FIFO underrun error interrupt
+  *            @arg SDIO_IT_RXOVERR:  Received FIFO overrun error interrupt
+  *            @arg SDIO_IT_CMDREND:  Command response received (CRC check passed) interrupt
+  *            @arg SDIO_IT_CMDSENT:  Command sent (no response required) interrupt
+  *            @arg SDIO_IT_DATAEND:  Data end (data counter, DATACOUNT, is zero) interrupt
+  *            @arg SDIO_IT_DBCKEND:  Data block sent/received (CRC check passed) interrupt
+  *            @arg SDIO_IT_CMDACT:   Command transfer in progress interrupt
+  *            @arg SDIO_IT_TXACT:    Data transmit in progress interrupt
+  *            @arg SDIO_IT_RXACT:    Data receive in progress interrupt
+  *            @arg SDIO_IT_TXFIFOHE: Transmit FIFO Half Empty interrupt
+  *            @arg SDIO_IT_RXFIFOHF: Receive FIFO Half Full interrupt
+  *            @arg SDIO_IT_TXFIFOF:  Transmit FIFO full interrupt
+  *            @arg SDIO_IT_RXFIFOF:  Receive FIFO full interrupt
+  *            @arg SDIO_IT_TXFIFOE:  Transmit FIFO empty interrupt
+  *            @arg SDIO_IT_RXFIFOE:  Receive FIFO empty interrupt
+  *            @arg SDIO_IT_TXDAVL:   Data available in transmit FIFO interrupt
+  *            @arg SDIO_IT_RXDAVL:   Data available in receive FIFO interrupt
+  *            @arg SDIO_IT_SDIOIT:   SDIO interrupt received interrupt
+  * @retval None
+  */
+#define __HAL_SD_ENABLE_IT(__HANDLE__, __INTERRUPT__) __SDIO_ENABLE_IT((__HANDLE__)->Instance, (__INTERRUPT__))
+
+/**
+  * @brief  Disable the SD device interrupt.
+  * @param  __HANDLE__: SD Handle   
+  * @param  __INTERRUPT__: specifies the SDMMC interrupt sources to be disabled.
+  *          This parameter can be one or a combination of the following values:
+  *            @arg SDIO_IT_CCRCFAIL: Command response received (CRC check failed) interrupt
+  *            @arg SDIO_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt
+  *            @arg SDIO_IT_CTIMEOUT: Command response timeout interrupt
+  *            @arg SDIO_IT_DTIMEOUT: Data timeout interrupt
+  *            @arg SDIO_IT_TXUNDERR: Transmit FIFO underrun error interrupt
+  *            @arg SDIO_IT_RXOVERR:  Received FIFO overrun error interrupt
+  *            @arg SDIO_IT_CMDREND:  Command response received (CRC check passed) interrupt
+  *            @arg SDIO_IT_CMDSENT:  Command sent (no response required) interrupt
+  *            @arg SDIO_IT_DATAEND:  Data end (data counter, DATACOUNT, is zero) interrupt
+  *            @arg SDIO_IT_DBCKEND:  Data block sent/received (CRC check passed) interrupt
+  *            @arg SDIO_IT_CMDACT:   Command transfer in progress interrupt
+  *            @arg SDIO_IT_TXACT:    Data transmit in progress interrupt
+  *            @arg SDIO_IT_RXACT:    Data receive in progress interrupt
+  *            @arg SDIO_IT_TXFIFOHE: Transmit FIFO Half Empty interrupt
+  *            @arg SDIO_IT_RXFIFOHF: Receive FIFO Half Full interrupt
+  *            @arg SDIO_IT_TXFIFOF:  Transmit FIFO full interrupt
+  *            @arg SDIO_IT_RXFIFOF:  Receive FIFO full interrupt
+  *            @arg SDIO_IT_TXFIFOE:  Transmit FIFO empty interrupt
+  *            @arg SDIO_IT_RXFIFOE:  Receive FIFO empty interrupt
+  *            @arg SDIO_IT_TXDAVL:   Data available in transmit FIFO interrupt
+  *            @arg SDIO_IT_RXDAVL:   Data available in receive FIFO interrupt
+  *            @arg SDIO_IT_SDIOIT:   SDIO interrupt received interrupt   
+  * @retval None
+  */
+#define __HAL_SD_DISABLE_IT(__HANDLE__, __INTERRUPT__) __SDIO_DISABLE_IT((__HANDLE__)->Instance, (__INTERRUPT__))
+
+/**
+  * @brief  Check whether the specified SD flag is set or not. 
+  * @param  __HANDLE__: SD Handle   
+  * @param  __FLAG__: specifies the flag to check. 
+  *          This parameter can be one of the following values:
+  *            @arg SDIO_FLAG_CCRCFAIL: Command response received (CRC check failed)
+  *            @arg SDIO_FLAG_DCRCFAIL: Data block sent/received (CRC check failed)
+  *            @arg SDIO_FLAG_CTIMEOUT: Command response timeout
+  *            @arg SDIO_FLAG_DTIMEOUT: Data timeout
+  *            @arg SDIO_FLAG_TXUNDERR: Transmit FIFO underrun error
+  *            @arg SDIO_FLAG_RXOVERR:  Received FIFO overrun error
+  *            @arg SDIO_FLAG_CMDREND:  Command response received (CRC check passed)
+  *            @arg SDIO_FLAG_CMDSENT:  Command sent (no response required)
+  *            @arg SDIO_FLAG_DATAEND:  Data end (data counter, DATACOUNT, is zero)
+  *            @arg SDIO_FLAG_DBCKEND:  Data block sent/received (CRC check passed)
+  *            @arg SDIO_FLAG_CMDACT:   Command transfer in progress
+  *            @arg SDIO_FLAG_TXACT:    Data transmit in progress
+  *            @arg SDIO_FLAG_RXACT:    Data receive in progress
+  *            @arg SDIO_FLAG_TXFIFOHE: Transmit FIFO Half Empty
+  *            @arg SDIO_FLAG_RXFIFOHF: Receive FIFO Half Full
+  *            @arg SDIO_FLAG_TXFIFOF:  Transmit FIFO full
+  *            @arg SDIO_FLAG_RXFIFOF:  Receive FIFO full
+  *            @arg SDIO_FLAG_TXFIFOE:  Transmit FIFO empty
+  *            @arg SDIO_FLAG_RXFIFOE:  Receive FIFO empty
+  *            @arg SDIO_FLAG_TXDAVL:   Data available in transmit FIFO
+  *            @arg SDIO_FLAG_RXDAVL:   Data available in receive FIFO
+  *            @arg SDIO_FLAG_SDIOIT:   SDIO interrupt received
+  * @retval The new state of SD FLAG (SET or RESET).
+  */
+#define __HAL_SD_GET_FLAG(__HANDLE__, __FLAG__) __SDIO_GET_FLAG((__HANDLE__)->Instance, (__FLAG__))
+
+/**
+  * @brief  Clear the SD's pending flags.
+  * @param  __HANDLE__: SD Handle  
+  * @param  __FLAG__: specifies the flag to clear.  
+  *          This parameter can be one or a combination of the following values:
+  *            @arg SDIO_FLAG_CCRCFAIL: Command response received (CRC check failed)
+  *            @arg SDIO_FLAG_DCRCFAIL: Data block sent/received (CRC check failed)
+  *            @arg SDIO_FLAG_CTIMEOUT: Command response timeout
+  *            @arg SDIO_FLAG_DTIMEOUT: Data timeout
+  *            @arg SDIO_FLAG_TXUNDERR: Transmit FIFO underrun error
+  *            @arg SDIO_FLAG_RXOVERR:  Received FIFO overrun error
+  *            @arg SDIO_FLAG_CMDREND:  Command response received (CRC check passed)
+  *            @arg SDIO_FLAG_CMDSENT:  Command sent (no response required)
+  *            @arg SDIO_FLAG_DATAEND:  Data end (data counter, DATACOUNT, is zero)
+  *            @arg SDIO_FLAG_DBCKEND:  Data block sent/received (CRC check passed)
+  *            @arg SDIO_FLAG_SDIOIT:   SDIO interrupt received
+  * @retval None
+  */
+#define __HAL_SD_CLEAR_FLAG(__HANDLE__, __FLAG__) __SDIO_CLEAR_FLAG((__HANDLE__)->Instance, (__FLAG__))
+
+/**
+  * @brief  Check whether the specified SD interrupt has occurred or not.
+  * @param  __HANDLE__: SD Handle   
+  * @param  __INTERRUPT__: specifies the SDMMC interrupt source to check. 
+  *          This parameter can be one of the following values:
+  *            @arg SDIO_IT_CCRCFAIL: Command response received (CRC check failed) interrupt
+  *            @arg SDIO_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt
+  *            @arg SDIO_IT_CTIMEOUT: Command response timeout interrupt
+  *            @arg SDIO_IT_DTIMEOUT: Data timeout interrupt
+  *            @arg SDIO_IT_TXUNDERR: Transmit FIFO underrun error interrupt
+  *            @arg SDIO_IT_RXOVERR:  Received FIFO overrun error interrupt
+  *            @arg SDIO_IT_CMDREND:  Command response received (CRC check passed) interrupt
+  *            @arg SDIO_IT_CMDSENT:  Command sent (no response required) interrupt
+  *            @arg SDIO_IT_DATAEND:  Data end (data counter, DATACOUNT, is zero) interrupt
+  *            @arg SDIO_IT_DBCKEND:  Data block sent/received (CRC check passed) interrupt
+  *            @arg SDIO_IT_CMDACT:   Command transfer in progress interrupt
+  *            @arg SDIO_IT_TXACT:    Data transmit in progress interrupt
+  *            @arg SDIO_IT_RXACT:    Data receive in progress interrupt
+  *            @arg SDIO_IT_TXFIFOHE: Transmit FIFO Half Empty interrupt
+  *            @arg SDIO_IT_RXFIFOHF: Receive FIFO Half Full interrupt
+  *            @arg SDIO_IT_TXFIFOF:  Transmit FIFO full interrupt
+  *            @arg SDIO_IT_RXFIFOF:  Receive FIFO full interrupt
+  *            @arg SDIO_IT_TXFIFOE:  Transmit FIFO empty interrupt
+  *            @arg SDIO_IT_RXFIFOE:  Receive FIFO empty interrupt
+  *            @arg SDIO_IT_TXDAVL:   Data available in transmit FIFO interrupt
+  *            @arg SDIO_IT_RXDAVL:   Data available in receive FIFO interrupt
+  *            @arg SDIO_IT_SDIOIT:   SDIO interrupt received interrupt
+  * @retval The new state of SD IT (SET or RESET).
+  */
+#define __HAL_SD_GET_IT(__HANDLE__, __INTERRUPT__) __SDIO_GET_IT((__HANDLE__)->Instance, (__INTERRUPT__))
+
+/**
+  * @brief  Clear the SD's interrupt pending bits.
+  * @param  __HANDLE__: SD Handle
+  * @param  __INTERRUPT__: specifies the interrupt pending bit to clear. 
+  *          This parameter can be one or a combination of the following values:
+  *            @arg SDIO_IT_CCRCFAIL: Command response received (CRC check failed) interrupt
+  *            @arg SDIO_IT_DCRCFAIL: Data block sent/received (CRC check failed) interrupt
+  *            @arg SDIO_IT_CTIMEOUT: Command response timeout interrupt
+  *            @arg SDIO_IT_DTIMEOUT: Data timeout interrupt
+  *            @arg SDIO_IT_TXUNDERR: Transmit FIFO underrun error interrupt
+  *            @arg SDIO_IT_RXOVERR:  Received FIFO overrun error interrupt
+  *            @arg SDIO_IT_CMDREND:  Command response received (CRC check passed) interrupt
+  *            @arg SDIO_IT_CMDSENT:  Command sent (no response required) interrupt
+  *            @arg SDIO_IT_DATAEND:  Data end (data counter, DATACOUNT, is zero) interrupt
+  *            @arg SDIO_IT_SDIOIT:   SDIO interrupt received interrupt
+  * @retval None
+  */
+#define __HAL_SD_CLEAR_IT(__HANDLE__, __INTERRUPT__) __SDIO_CLEAR_IT((__HANDLE__)->Instance, (__INTERRUPT__))
+
+/**
+  * @}
+  */
+  
+/* Exported functions --------------------------------------------------------*/
+/** @defgroup SD_Exported_Functions SD Exported Functions
+  * @{
+  */
+  
+/** @defgroup SD_Exported_Functions_Group1 Initialization and de-initialization functions
+  * @{
+  */
+HAL_StatusTypeDef HAL_SD_Init(SD_HandleTypeDef *hsd);
+HAL_StatusTypeDef HAL_SD_InitCard(SD_HandleTypeDef *hsd);
+HAL_StatusTypeDef HAL_SD_DeInit (SD_HandleTypeDef *hsd);
+void HAL_SD_MspInit(SD_HandleTypeDef *hsd);
+void HAL_SD_MspDeInit(SD_HandleTypeDef *hsd);
+/**
+  * @}
+  */
+  
+/** @defgroup SD_Exported_Functions_Group2 Input and Output operation functions
+  * @{
+  */
+/* Blocking mode: Polling */
+HAL_StatusTypeDef HAL_SD_ReadBlocks(SD_HandleTypeDef *hsd, uint8_t *pData, uint32_t BlockAdd, uint32_t NumberOfBlocks, uint32_t Timeout);
+HAL_StatusTypeDef HAL_SD_WriteBlocks(SD_HandleTypeDef *hsd, uint8_t *pData, uint32_t BlockAdd, uint32_t NumberOfBlocks, uint32_t Timeout);
+HAL_StatusTypeDef HAL_SD_Erase(SD_HandleTypeDef *hsd, uint32_t BlockStartAdd, uint32_t BlockEndAdd);
+/* Non-Blocking mode: IT */
+HAL_StatusTypeDef HAL_SD_ReadBlocks_IT(SD_HandleTypeDef *hsd, uint8_t *pData, uint32_t BlockAdd, uint32_t NumberOfBlocks);
+HAL_StatusTypeDef HAL_SD_WriteBlocks_IT(SD_HandleTypeDef *hsd, uint8_t *pData, uint32_t BlockAdd, uint32_t NumberOfBlocks);
+/* Non-Blocking mode: DMA */
+HAL_StatusTypeDef HAL_SD_ReadBlocks_DMA(SD_HandleTypeDef *hsd, uint8_t *pData, uint32_t BlockAdd, uint32_t NumberOfBlocks);
+HAL_StatusTypeDef HAL_SD_WriteBlocks_DMA(SD_HandleTypeDef *hsd, uint8_t *pData, uint32_t BlockAdd, uint32_t NumberOfBlocks);
+
+void HAL_SD_IRQHandler(SD_HandleTypeDef *hsd);
+
+/* Callback in non blocking modes (DMA) */
+void HAL_SD_TxCpltCallback(SD_HandleTypeDef *hsd);
+void HAL_SD_RxCpltCallback(SD_HandleTypeDef *hsd);
+void HAL_SD_ErrorCallback(SD_HandleTypeDef *hsd);
+void HAL_SD_AbortCallback(SD_HandleTypeDef *hsd);
+
+#if defined (USE_HAL_SD_REGISTER_CALLBACKS) && (USE_HAL_SD_REGISTER_CALLBACKS == 1U)
+/* SD callback registering/unregistering */
+HAL_StatusTypeDef HAL_SD_RegisterCallback  (SD_HandleTypeDef *hsd, HAL_SD_CallbackIDTypeDef CallbackId, pSD_CallbackTypeDef pCallback);
+HAL_StatusTypeDef HAL_SD_UnRegisterCallback(SD_HandleTypeDef *hsd, HAL_SD_CallbackIDTypeDef CallbackId);
+#endif /* USE_HAL_SD_REGISTER_CALLBACKS */
+
+/**
+  * @}
+  */
+  
+/** @defgroup SD_Exported_Functions_Group3 Peripheral Control functions
+  * @{
+  */
+HAL_StatusTypeDef HAL_SD_ConfigWideBusOperation(SD_HandleTypeDef *hsd, uint32_t WideMode);
+/**
+  * @}
+  */
+
+/** @defgroup SD_Exported_Functions_Group4 SD card related functions
+  * @{
+  */
+HAL_StatusTypeDef       HAL_SD_SendSDStatus(SD_HandleTypeDef *hsd, uint32_t *pSDstatus);
+HAL_SD_CardStateTypeDef HAL_SD_GetCardState(SD_HandleTypeDef *hsd);
+HAL_StatusTypeDef       HAL_SD_GetCardCID(SD_HandleTypeDef *hsd, HAL_SD_CardCIDTypeDef *pCID);
+HAL_StatusTypeDef       HAL_SD_GetCardCSD(SD_HandleTypeDef *hsd, HAL_SD_CardCSDTypeDef *pCSD);
+HAL_StatusTypeDef       HAL_SD_GetCardStatus(SD_HandleTypeDef *hsd, HAL_SD_CardStatusTypeDef *pStatus);
+HAL_StatusTypeDef       HAL_SD_GetCardInfo(SD_HandleTypeDef *hsd, HAL_SD_CardInfoTypeDef *pCardInfo);
+/**
+  * @}
+  */
+
+/** @defgroup SD_Exported_Functions_Group5 Peripheral State and Errors functions
+  * @{
+  */
+HAL_SD_StateTypeDef HAL_SD_GetState(SD_HandleTypeDef *hsd);
+uint32_t HAL_SD_GetError(SD_HandleTypeDef *hsd);
+/**
+  * @}
+  */
+
+/** @defgroup SD_Exported_Functions_Group6 Perioheral Abort management
+  * @{
+  */
+HAL_StatusTypeDef HAL_SD_Abort(SD_HandleTypeDef *hsd);
+HAL_StatusTypeDef HAL_SD_Abort_IT(SD_HandleTypeDef *hsd);
+/**
+  * @}
+  */
+    
+/* Private types -------------------------------------------------------------*/
+/** @defgroup SD_Private_Types SD Private Types
+  * @{
+  */
+
+/**
+  * @}
+  */ 
+
+/* Private defines -----------------------------------------------------------*/
+/** @defgroup SD_Private_Defines SD Private Defines
+  * @{
+  */
+
+/**
+  * @}
+  */ 
+          
+/* Private variables ---------------------------------------------------------*/
+/** @defgroup SD_Private_Variables SD Private Variables
+  * @{
+  */
+
+/**
+  * @}
+  */ 
+
+/* Private constants ---------------------------------------------------------*/
+/** @defgroup SD_Private_Constants SD Private Constants
+  * @{
+  */
+
+/**
+  * @}
+  */ 
+
+/* Private macros ------------------------------------------------------------*/
+/** @defgroup SD_Private_Macros SD Private Macros
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/* Private functions prototypes ----------------------------------------------*/
+/** @defgroup SD_Private_Functions_Prototypes SD Private Functions Prototypes
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/* Private functions ---------------------------------------------------------*/
+/** @defgroup SD_Private_Functions SD Private Functions
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+
+/**
+  * @}
+  */ 
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#endif /* SDIO */
+
+#ifdef __cplusplus
+}
+#endif
+
+
+#endif /* STM32F1xx_HAL_SD_H */ 
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_smartcard.h

@@ -0,0 +1,745 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_hal_smartcard.h
+  * @author  MCD Application Team
+  * @brief   Header file of SMARTCARD HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F1xx_HAL_SMARTCARD_H
+#define __STM32F1xx_HAL_SMARTCARD_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_hal_def.h"
+
+/** @addtogroup STM32F1xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup SMARTCARD
+  * @{
+  */
+
+/* Exported types ------------------------------------------------------------*/
+/** @defgroup SMARTCARD_Exported_Types SMARTCARD Exported Types
+  * @{
+  */
+
+/**
+  * @brief SMARTCARD Init Structure definition
+  */
+typedef struct
+{
+  uint32_t BaudRate;                  /*!< This member configures the SmartCard communication baud rate.
+                                           The baud rate is computed using the following formula:
+                                           - IntegerDivider = ((PCLKx) / (16 * (hsc->Init.BaudRate)))
+                                           - FractionalDivider = ((IntegerDivider - ((uint32_t) IntegerDivider)) * 16) + 0.5 */
+
+  uint32_t WordLength;                /*!< Specifies the number of data bits transmitted or received in a frame.
+                                           This parameter can be a value of @ref SMARTCARD_Word_Length */
+
+  uint32_t StopBits;                  /*!< Specifies the number of stop bits transmitted.
+                                           This parameter can be a value of @ref SMARTCARD_Stop_Bits */
+
+  uint32_t Parity;                    /*!< Specifies the parity mode.
+                                           This parameter can be a value of @ref SMARTCARD_Parity
+                                           @note When parity is enabled, the computed parity is inserted
+                                                 at the MSB position of the transmitted data (9th bit when
+                                                 the word length is set to 9 data bits; 8th bit when the
+                                                 word length is set to 8 data bits).*/
+
+  uint32_t Mode;                      /*!< Specifies whether the Receive or Transmit mode is enabled or disabled.
+                                           This parameter can be a value of @ref SMARTCARD_Mode */
+
+  uint32_t CLKPolarity;               /*!< Specifies the steady state of the serial clock.
+                                           This parameter can be a value of @ref SMARTCARD_Clock_Polarity */
+
+  uint32_t CLKPhase;                  /*!< Specifies the clock transition on which the bit capture is made.
+                                           This parameter can be a value of @ref SMARTCARD_Clock_Phase */
+
+  uint32_t CLKLastBit;                /*!< Specifies whether the clock pulse corresponding to the last transmitted
+                                           data bit (MSB) has to be output on the SCLK pin in synchronous mode.
+                                           This parameter can be a value of @ref SMARTCARD_Last_Bit */
+
+  uint32_t Prescaler;                 /*!< Specifies the SmartCard Prescaler value used for dividing the system clock
+                                           to provide the smartcard clock. The value given in the register (5 significant bits)
+                                           is multiplied by 2 to give the division factor of the source clock frequency.
+                                           This parameter can be a value of @ref SMARTCARD_Prescaler */
+
+  uint32_t GuardTime;                 /*!< Specifies the SmartCard Guard Time value in terms of number of baud clocks */
+
+  uint32_t NACKState;                 /*!< Specifies the SmartCard NACK Transmission state.
+                                           This parameter can be a value of @ref SMARTCARD_NACK_State */
+}SMARTCARD_InitTypeDef;
+
+/**
+  * @brief HAL SMARTCARD State structures definition
+  * @note  HAL SMARTCARD State value is a combination of 2 different substates: gState and RxState.
+  *        - gState contains SMARTCARD state information related to global Handle management
+  *          and also information related to Tx operations.
+  *          gState value coding follow below described bitmap :
+  *          b7-b6  Error information
+  *             00 : No Error
+  *             01 : (Not Used)
+  *             10 : Timeout
+  *             11 : Error
+  *          b5     IP initialization status
+  *             0  : Reset (IP not initialized)
+  *             1  : Init done (IP initialized. HAL SMARTCARD Init function already called)
+  *          b4-b3  (not used)
+  *             xx : Should be set to 00
+  *          b2     Intrinsic process state
+  *             0  : Ready
+  *             1  : Busy (IP busy with some configuration or internal operations)
+  *          b1     (not used)
+  *             x  : Should be set to 0
+  *          b0     Tx state
+  *             0  : Ready (no Tx operation ongoing)
+  *             1  : Busy (Tx operation ongoing)
+  *        - RxState contains information related to Rx operations.
+  *          RxState value coding follow below described bitmap :
+  *          b7-b6  (not used)
+  *             xx : Should be set to 00
+  *          b5     IP initialization status
+  *             0  : Reset (IP not initialized)
+  *             1  : Init done (IP initialized)
+  *          b4-b2  (not used)
+  *            xxx : Should be set to 000
+  *          b1     Rx state
+  *             0  : Ready (no Rx operation ongoing)
+  *             1  : Busy (Rx operation ongoing)
+  *          b0     (not used)
+  *             x  : Should be set to 0.
+  */
+typedef enum
+{
+  HAL_SMARTCARD_STATE_RESET             = 0x00U,    /*!< Peripheral is not yet Initialized
+                                                        Value is allowed for gState and RxState */
+  HAL_SMARTCARD_STATE_READY             = 0x20U,    /*!< Peripheral Initialized and ready for use
+                                                        Value is allowed for gState and RxState */
+  HAL_SMARTCARD_STATE_BUSY              = 0x24U,    /*!< an internal process is ongoing
+                                                        Value is allowed for gState only */
+  HAL_SMARTCARD_STATE_BUSY_TX           = 0x21U,    /*!< Data Transmission process is ongoing
+                                                        Value is allowed for gState only */
+  HAL_SMARTCARD_STATE_BUSY_RX           = 0x22U,    /*!< Data Reception process is ongoing
+                                                        Value is allowed for RxState only */
+  HAL_SMARTCARD_STATE_BUSY_TX_RX        = 0x23U,    /*!< Data Transmission and Reception process is ongoing
+                                                        Not to be used for neither gState nor RxState.
+                                                        Value is result of combination (Or) between gState and RxState values */
+  HAL_SMARTCARD_STATE_TIMEOUT           = 0xA0U,    /*!< Timeout state
+                                                        Value is allowed for gState only */
+  HAL_SMARTCARD_STATE_ERROR             = 0xE0U     /*!< Error
+                                                        Value is allowed for gState only */
+}HAL_SMARTCARD_StateTypeDef;
+
+/**
+  * @brief  SMARTCARD handle Structure definition
+  */
+typedef struct __SMARTCARD_HandleTypeDef
+{
+  USART_TypeDef                    *Instance;        /*!< USART registers base address */
+
+  SMARTCARD_InitTypeDef            Init;             /*!< SmartCard communication parameters */
+
+  uint8_t                          *pTxBuffPtr;      /*!< Pointer to SmartCard Tx transfer Buffer */
+
+  uint16_t                         TxXferSize;       /*!< SmartCard Tx Transfer size */
+
+  __IO uint16_t                    TxXferCount;      /*!< SmartCard Tx Transfer Counter */
+
+  uint8_t                          *pRxBuffPtr;      /*!< Pointer to SmartCard Rx transfer Buffer */
+
+  uint16_t                         RxXferSize;       /*!< SmartCard Rx Transfer size */
+
+  __IO uint16_t                    RxXferCount;      /*!< SmartCard Rx Transfer Counter */
+
+  DMA_HandleTypeDef                *hdmatx;          /*!< SmartCard Tx DMA Handle parameters */
+
+  DMA_HandleTypeDef                *hdmarx;          /*!< SmartCard Rx DMA Handle parameters */
+
+  HAL_LockTypeDef                  Lock;             /*!< Locking object */
+
+  __IO HAL_SMARTCARD_StateTypeDef  gState;           /*!< SmartCard state information related to global Handle management
+                                                        and also related to Tx operations.
+                                                        This parameter can be a value of @ref HAL_SMARTCARD_StateTypeDef */
+
+  __IO HAL_SMARTCARD_StateTypeDef  RxState;          /*!< SmartCard state information related to Rx operations.
+                                                        This parameter can be a value of @ref HAL_SMARTCARD_StateTypeDef */
+
+  __IO uint32_t                    ErrorCode;        /*!< SmartCard Error code */
+
+#if (USE_HAL_SMARTCARD_REGISTER_CALLBACKS == 1)
+  void (* TxCpltCallback)(struct __SMARTCARD_HandleTypeDef *hsc);            /*!< SMARTCARD Tx Complete Callback             */
+
+  void (* RxCpltCallback)(struct __SMARTCARD_HandleTypeDef *hsc);            /*!< SMARTCARD Rx Complete Callback             */
+
+  void (* ErrorCallback)(struct __SMARTCARD_HandleTypeDef *hsc);             /*!< SMARTCARD Error Callback                   */
+
+  void (* AbortCpltCallback)(struct __SMARTCARD_HandleTypeDef *hsc);         /*!< SMARTCARD Abort Complete Callback          */
+
+  void (* AbortTransmitCpltCallback)(struct __SMARTCARD_HandleTypeDef *hsc); /*!< SMARTCARD Abort Transmit Complete Callback */
+
+  void (* AbortReceiveCpltCallback)(struct __SMARTCARD_HandleTypeDef *hsc);  /*!< SMARTCARD Abort Receive Complete Callback  */
+
+  void (* MspInitCallback)(struct __SMARTCARD_HandleTypeDef *hsc);           /*!< SMARTCARD Msp Init callback                */
+
+  void (* MspDeInitCallback)(struct __SMARTCARD_HandleTypeDef *hsc);         /*!< SMARTCARD Msp DeInit callback              */
+#endif  /* USE_HAL_SMARTCARD_REGISTER_CALLBACKS */
+
+} SMARTCARD_HandleTypeDef;
+
+#if (USE_HAL_SMARTCARD_REGISTER_CALLBACKS == 1)
+/**
+  * @brief  HAL SMARTCARD Callback ID enumeration definition
+  */
+typedef enum
+{
+  HAL_SMARTCARD_TX_COMPLETE_CB_ID             = 0x00U,    /*!< SMARTCARD Tx Complete Callback ID             */
+  HAL_SMARTCARD_RX_COMPLETE_CB_ID             = 0x01U,    /*!< SMARTCARD Rx Complete Callback ID             */
+  HAL_SMARTCARD_ERROR_CB_ID                   = 0x02U,    /*!< SMARTCARD Error Callback ID                   */
+  HAL_SMARTCARD_ABORT_COMPLETE_CB_ID          = 0x03U,    /*!< SMARTCARD Abort Complete Callback ID          */
+  HAL_SMARTCARD_ABORT_TRANSMIT_COMPLETE_CB_ID = 0x04U,    /*!< SMARTCARD Abort Transmit Complete Callback ID */
+  HAL_SMARTCARD_ABORT_RECEIVE_COMPLETE_CB_ID  = 0x05U,    /*!< SMARTCARD Abort Receive Complete Callback ID  */
+
+  HAL_SMARTCARD_MSPINIT_CB_ID                 = 0x08U,    /*!< SMARTCARD MspInit callback ID                 */
+  HAL_SMARTCARD_MSPDEINIT_CB_ID               = 0x09U     /*!< SMARTCARD MspDeInit callback ID               */
+
+} HAL_SMARTCARD_CallbackIDTypeDef;
+
+/**
+  * @brief  HAL SMARTCARD Callback pointer definition
+  */
+typedef  void (*pSMARTCARD_CallbackTypeDef)(SMARTCARD_HandleTypeDef *hsc);  /*!< pointer to an SMARTCARD callback function */
+
+#endif /* USE_HAL_SMARTCARD_REGISTER_CALLBACKS */
+
+/**
+  * @}
+  */
+
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup SMARTCARD_Exported_Constants  SMARTCARD Exported constants
+  * @{
+  */
+
+/** @defgroup SMARTCARD_Error_Code SMARTCARD Error Code
+  * @{
+  */
+#define HAL_SMARTCARD_ERROR_NONE             0x00000000U   /*!< No error            */
+#define HAL_SMARTCARD_ERROR_PE               0x00000001U   /*!< Parity error        */
+#define HAL_SMARTCARD_ERROR_NE               0x00000002U   /*!< Noise error         */
+#define HAL_SMARTCARD_ERROR_FE               0x00000004U   /*!< Frame error         */
+#define HAL_SMARTCARD_ERROR_ORE              0x00000008U   /*!< Overrun error       */
+#define HAL_SMARTCARD_ERROR_DMA              0x00000010U   /*!< DMA transfer error  */
+#if (USE_HAL_SMARTCARD_REGISTER_CALLBACKS == 1)
+#define HAL_SMARTCARD_ERROR_INVALID_CALLBACK 0x00000020U   /*!< Invalid Callback error  */
+#endif /* USE_HAL_SMARTCARD_REGISTER_CALLBACKS */
+/**
+  * @}
+  */
+
+/** @defgroup SMARTCARD_Word_Length SMARTCARD Word Length
+  * @{
+  */
+#define SMARTCARD_WORDLENGTH_9B             ((uint32_t)USART_CR1_M)
+/**
+  * @}
+  */
+
+/** @defgroup SMARTCARD_Stop_Bits SMARTCARD Number of Stop Bits
+  * @{
+  */
+#define SMARTCARD_STOPBITS_0_5              ((uint32_t)USART_CR2_STOP_0)
+#define SMARTCARD_STOPBITS_1_5              ((uint32_t)(USART_CR2_STOP_0 | USART_CR2_STOP_1))
+/**
+  * @}
+  */
+
+/** @defgroup SMARTCARD_Parity SMARTCARD Parity
+  * @{
+  */
+#define SMARTCARD_PARITY_EVEN               ((uint32_t)USART_CR1_PCE)
+#define SMARTCARD_PARITY_ODD                ((uint32_t)(USART_CR1_PCE | USART_CR1_PS))
+/**
+  * @}
+  */
+
+/** @defgroup SMARTCARD_Mode SMARTCARD Mode
+  * @{
+  */
+#define SMARTCARD_MODE_RX                   ((uint32_t)USART_CR1_RE)
+#define SMARTCARD_MODE_TX                   ((uint32_t)USART_CR1_TE)
+#define SMARTCARD_MODE_TX_RX                ((uint32_t)(USART_CR1_TE |USART_CR1_RE))
+/**
+  * @}
+  */
+
+/** @defgroup SMARTCARD_Clock_Polarity SMARTCARD Clock Polarity
+  * @{
+  */
+#define SMARTCARD_POLARITY_LOW              0x00000000U
+#define SMARTCARD_POLARITY_HIGH             ((uint32_t)USART_CR2_CPOL)
+/**
+  * @}
+  */
+
+/** @defgroup SMARTCARD_Clock_Phase  SMARTCARD Clock Phase
+  * @{
+  */
+#define SMARTCARD_PHASE_1EDGE               0x00000000U
+#define SMARTCARD_PHASE_2EDGE               ((uint32_t)USART_CR2_CPHA)
+/**
+  * @}
+  */
+
+/** @defgroup SMARTCARD_Last_Bit  SMARTCARD Last Bit
+  * @{
+  */
+#define SMARTCARD_LASTBIT_DISABLE           0x00000000U
+#define SMARTCARD_LASTBIT_ENABLE            ((uint32_t)USART_CR2_LBCL)
+/**
+  * @}
+  */
+
+/** @defgroup SMARTCARD_NACK_State  SMARTCARD NACK State
+  * @{
+  */
+#define SMARTCARD_NACK_ENABLE               ((uint32_t)USART_CR3_NACK)
+#define SMARTCARD_NACK_DISABLE              0x00000000U
+/**
+  * @}
+  */
+
+/** @defgroup SMARTCARD_DMA_Requests   SMARTCARD DMA requests
+  * @{
+  */
+#define SMARTCARD_DMAREQ_TX                 ((uint32_t)USART_CR3_DMAT)
+#define SMARTCARD_DMAREQ_RX                 ((uint32_t)USART_CR3_DMAR)
+/**
+  * @}
+  */
+
+/** @defgroup SMARTCARD_Prescaler SMARTCARD Prescaler
+  * @{
+  */
+#define SMARTCARD_PRESCALER_SYSCLK_DIV2     0x00000001U          /*!< SYSCLK divided by 2 */
+#define SMARTCARD_PRESCALER_SYSCLK_DIV4     0x00000002U          /*!< SYSCLK divided by 4 */
+#define SMARTCARD_PRESCALER_SYSCLK_DIV6     0x00000003U          /*!< SYSCLK divided by 6 */
+#define SMARTCARD_PRESCALER_SYSCLK_DIV8     0x00000004U          /*!< SYSCLK divided by 8 */
+#define SMARTCARD_PRESCALER_SYSCLK_DIV10    0x00000005U          /*!< SYSCLK divided by 10 */
+#define SMARTCARD_PRESCALER_SYSCLK_DIV12    0x00000006U          /*!< SYSCLK divided by 12 */
+#define SMARTCARD_PRESCALER_SYSCLK_DIV14    0x00000007U          /*!< SYSCLK divided by 14 */
+#define SMARTCARD_PRESCALER_SYSCLK_DIV16    0x00000008U          /*!< SYSCLK divided by 16 */
+#define SMARTCARD_PRESCALER_SYSCLK_DIV18    0x00000009U          /*!< SYSCLK divided by 18 */
+#define SMARTCARD_PRESCALER_SYSCLK_DIV20    0x0000000AU          /*!< SYSCLK divided by 20 */
+#define SMARTCARD_PRESCALER_SYSCLK_DIV22    0x0000000BU          /*!< SYSCLK divided by 22 */
+#define SMARTCARD_PRESCALER_SYSCLK_DIV24    0x0000000CU          /*!< SYSCLK divided by 24 */
+#define SMARTCARD_PRESCALER_SYSCLK_DIV26    0x0000000DU          /*!< SYSCLK divided by 26 */
+#define SMARTCARD_PRESCALER_SYSCLK_DIV28    0x0000000EU          /*!< SYSCLK divided by 28 */
+#define SMARTCARD_PRESCALER_SYSCLK_DIV30    0x0000000FU          /*!< SYSCLK divided by 30 */
+#define SMARTCARD_PRESCALER_SYSCLK_DIV32    0x00000010U          /*!< SYSCLK divided by 32 */
+#define SMARTCARD_PRESCALER_SYSCLK_DIV34    0x00000011U          /*!< SYSCLK divided by 34 */
+#define SMARTCARD_PRESCALER_SYSCLK_DIV36    0x00000012U          /*!< SYSCLK divided by 36 */
+#define SMARTCARD_PRESCALER_SYSCLK_DIV38    0x00000013U          /*!< SYSCLK divided by 38 */
+#define SMARTCARD_PRESCALER_SYSCLK_DIV40    0x00000014U          /*!< SYSCLK divided by 40 */
+#define SMARTCARD_PRESCALER_SYSCLK_DIV42    0x00000015U          /*!< SYSCLK divided by 42 */
+#define SMARTCARD_PRESCALER_SYSCLK_DIV44    0x00000016U          /*!< SYSCLK divided by 44 */
+#define SMARTCARD_PRESCALER_SYSCLK_DIV46    0x00000017U          /*!< SYSCLK divided by 46 */
+#define SMARTCARD_PRESCALER_SYSCLK_DIV48    0x00000018U          /*!< SYSCLK divided by 48 */
+#define SMARTCARD_PRESCALER_SYSCLK_DIV50    0x00000019U          /*!< SYSCLK divided by 50 */
+#define SMARTCARD_PRESCALER_SYSCLK_DIV52    0x0000001AU          /*!< SYSCLK divided by 52 */
+#define SMARTCARD_PRESCALER_SYSCLK_DIV54    0x0000001BU          /*!< SYSCLK divided by 54 */
+#define SMARTCARD_PRESCALER_SYSCLK_DIV56    0x0000001CU          /*!< SYSCLK divided by 56 */
+#define SMARTCARD_PRESCALER_SYSCLK_DIV58    0x0000001DU          /*!< SYSCLK divided by 58 */
+#define SMARTCARD_PRESCALER_SYSCLK_DIV60    0x0000001EU          /*!< SYSCLK divided by 60 */
+#define SMARTCARD_PRESCALER_SYSCLK_DIV62    0x0000001FU          /*!< SYSCLK divided by 62 */
+/**
+  * @}
+  */
+
+/** @defgroup SmartCard_Flags SMARTCARD Flags
+  *        Elements values convention: 0xXXXX
+  *           - 0xXXXX  : Flag mask in the SR register
+  * @{
+  */
+#define SMARTCARD_FLAG_TXE                  ((uint32_t)USART_SR_TXE)
+#define SMARTCARD_FLAG_TC                   ((uint32_t)USART_SR_TC)
+#define SMARTCARD_FLAG_RXNE                 ((uint32_t)USART_SR_RXNE)
+#define SMARTCARD_FLAG_IDLE                 ((uint32_t)USART_SR_IDLE)
+#define SMARTCARD_FLAG_ORE                  ((uint32_t)USART_SR_ORE)
+#define SMARTCARD_FLAG_NE                   ((uint32_t)USART_SR_NE)
+#define SMARTCARD_FLAG_FE                   ((uint32_t)USART_SR_FE)
+#define SMARTCARD_FLAG_PE                   ((uint32_t)USART_SR_PE)
+/**
+  * @}
+  */
+
+/** @defgroup SmartCard_Interrupt_definition SMARTCARD Interrupts Definition
+  *        Elements values convention: 0xY000XXXX
+  *           - XXXX  : Interrupt mask in the Y register
+  *           - Y  : Interrupt source register (2bits)
+  *                 - 01: CR1 register
+  *                 - 11: CR3 register
+  * @{
+  */
+#define SMARTCARD_IT_PE                     ((uint32_t)(SMARTCARD_CR1_REG_INDEX << 28U | USART_CR1_PEIE))
+#define SMARTCARD_IT_TXE                    ((uint32_t)(SMARTCARD_CR1_REG_INDEX << 28U | USART_CR1_TXEIE))
+#define SMARTCARD_IT_TC                     ((uint32_t)(SMARTCARD_CR1_REG_INDEX << 28U | USART_CR1_TCIE))
+#define SMARTCARD_IT_RXNE                   ((uint32_t)(SMARTCARD_CR1_REG_INDEX << 28U | USART_CR1_RXNEIE))
+#define SMARTCARD_IT_IDLE                   ((uint32_t)(SMARTCARD_CR1_REG_INDEX << 28U | USART_CR1_IDLEIE))
+#define SMARTCARD_IT_ERR                    ((uint32_t)(SMARTCARD_CR3_REG_INDEX << 28U | USART_CR3_EIE))
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Exported macro ------------------------------------------------------------*/
+/** @defgroup SMARTCARD_Exported_Macros SMARTCARD Exported Macros
+  * @{
+  */
+
+/** @brief Reset SMARTCARD handle gstate & RxState
+  * @param  __HANDLE__ specifies the SMARTCARD Handle.
+  *         SMARTCARD Handle selects the USARTx peripheral (USART availability and x value depending on device).
+  * @retval None
+  */
+#if USE_HAL_SMARTCARD_REGISTER_CALLBACKS == 1
+#define __HAL_SMARTCARD_RESET_HANDLE_STATE(__HANDLE__)  do{                                                       \
+                                                           (__HANDLE__)->gState = HAL_SMARTCARD_STATE_RESET;      \
+                                                           (__HANDLE__)->RxState = HAL_SMARTCARD_STATE_RESET;     \
+                                                           (__HANDLE__)->MspInitCallback = NULL;                  \
+                                                           (__HANDLE__)->MspDeInitCallback = NULL;                \
+                                                          } while(0U)
+#else
+#define __HAL_SMARTCARD_RESET_HANDLE_STATE(__HANDLE__)  do{                                                       \
+                                                           (__HANDLE__)->gState = HAL_SMARTCARD_STATE_RESET;      \
+                                                           (__HANDLE__)->RxState = HAL_SMARTCARD_STATE_RESET;     \
+                                                          } while(0U)
+#endif /*USE_HAL_SMARTCARD_REGISTER_CALLBACKS  */
+
+/** @brief  Flush the Smartcard DR register
+  * @param  __HANDLE__ specifies the SMARTCARD Handle.
+  *         SMARTCARD Handle selects the USARTx peripheral (USART availability and x value depending on device).
+  * @retval None
+  */
+#define __HAL_SMARTCARD_FLUSH_DRREGISTER(__HANDLE__) ((__HANDLE__)->Instance->DR)
+
+/** @brief  Check whether the specified Smartcard flag is set or not.
+  * @param  __HANDLE__ specifies the SMARTCARD Handle.
+  *         SMARTCARD Handle selects the USARTx peripheral (USART availability and x value depending on device).
+  * @param  __FLAG__ specifies the flag to check.
+  *        This parameter can be one of the following values:
+  *            @arg SMARTCARD_FLAG_TXE:  Transmit data register empty flag
+  *            @arg SMARTCARD_FLAG_TC:   Transmission Complete flag
+  *            @arg SMARTCARD_FLAG_RXNE: Receive data register not empty flag
+  *            @arg SMARTCARD_FLAG_IDLE: Idle Line detection flag
+  *            @arg SMARTCARD_FLAG_ORE:  Overrun Error flag
+  *            @arg SMARTCARD_FLAG_NE:   Noise Error flag
+  *            @arg SMARTCARD_FLAG_FE:   Framing Error flag
+  *            @arg SMARTCARD_FLAG_PE:   Parity Error flag
+  * @retval The new state of __FLAG__ (TRUE or FALSE).
+  */
+#define __HAL_SMARTCARD_GET_FLAG(__HANDLE__, __FLAG__) (((__HANDLE__)->Instance->SR & (__FLAG__)) == (__FLAG__))
+
+/** @brief  Clear the specified Smartcard pending flags.
+  * @param  __HANDLE__ specifies the SMARTCARD Handle.
+  *         SMARTCARD Handle selects the USARTx peripheral (USART availability and x value depending on device).
+  * @param  __FLAG__ specifies the flag to check.
+  *          This parameter can be any combination of the following values:
+  *            @arg SMARTCARD_FLAG_TC:   Transmission Complete flag.
+  *            @arg SMARTCARD_FLAG_RXNE: Receive data register not empty flag.
+  *
+  * @note   PE (Parity error), FE (Framing error), NE (Noise error) and ORE (Overrun
+  *          error) flags are cleared by software sequence: a read operation to
+  *          USART_SR register followed by a read operation to USART_DR register.
+  * @note   RXNE flag can be also cleared by a read to the USART_DR register.
+  * @note   TC flag can be also cleared by software sequence: a read operation to
+  *          USART_SR register followed by a write operation to USART_DR register.
+  * @note   TXE flag is cleared only by a write to the USART_DR register.
+  * @retval None
+  */
+#define __HAL_SMARTCARD_CLEAR_FLAG(__HANDLE__, __FLAG__) ((__HANDLE__)->Instance->SR = ~(__FLAG__))
+
+/** @brief  Clear the SMARTCARD PE pending flag.
+  * @param  __HANDLE__ specifies the USART Handle.
+  *         SMARTCARD Handle selects the USARTx peripheral (USART availability and x value depending on device).
+  * @retval None
+  */
+#define __HAL_SMARTCARD_CLEAR_PEFLAG(__HANDLE__)  \
+    do{                                           \
+      __IO uint32_t tmpreg = 0x00U;               \
+      tmpreg = (__HANDLE__)->Instance->SR;        \
+      tmpreg = (__HANDLE__)->Instance->DR;        \
+      UNUSED(tmpreg);                             \
+    } while(0U)
+
+/** @brief  Clear the SMARTCARD FE pending flag.
+  * @param  __HANDLE__ specifies the USART Handle.
+  *         SMARTCARD Handle selects the USARTx peripheral (USART availability and x value depending on device).
+  * @retval None
+  */
+#define __HAL_SMARTCARD_CLEAR_FEFLAG(__HANDLE__) __HAL_SMARTCARD_CLEAR_PEFLAG(__HANDLE__)
+
+/** @brief  Clear the SMARTCARD NE pending flag.
+  * @param  __HANDLE__ specifies the USART Handle.
+  *         SMARTCARD Handle selects the USARTx peripheral (USART availability and x value depending on device).
+  * @retval None
+  */
+#define __HAL_SMARTCARD_CLEAR_NEFLAG(__HANDLE__) __HAL_SMARTCARD_CLEAR_PEFLAG(__HANDLE__)
+
+/** @brief  Clear the SMARTCARD ORE pending flag.
+  * @param  __HANDLE__ specifies the USART Handle.
+  *         SMARTCARD Handle selects the USARTx peripheral (USART availability and x value depending on device).
+  * @retval None
+  */
+#define __HAL_SMARTCARD_CLEAR_OREFLAG(__HANDLE__) __HAL_SMARTCARD_CLEAR_PEFLAG(__HANDLE__)
+
+/** @brief  Clear the SMARTCARD IDLE pending flag.
+  * @param  __HANDLE__ specifies the USART Handle.
+  *         SMARTCARD Handle selects the USARTx peripheral (USART availability and x value depending on device).
+  * @retval None
+  */
+#define __HAL_SMARTCARD_CLEAR_IDLEFLAG(__HANDLE__) __HAL_SMARTCARD_CLEAR_PEFLAG(__HANDLE__)
+
+/** @brief  Enable the specified SmartCard interrupt.
+  * @param  __HANDLE__ specifies the SMARTCARD Handle.
+  *         SMARTCARD Handle selects the USARTx peripheral (USART availability and x value depending on device).
+  * @param  __INTERRUPT__ specifies the SMARTCARD interrupt to enable.
+  *          This parameter can be one of the following values:
+  *            @arg SMARTCARD_IT_TXE:  Transmit Data Register empty interrupt
+  *            @arg SMARTCARD_IT_TC:   Transmission complete interrupt
+  *            @arg SMARTCARD_IT_RXNE: Receive Data register not empty interrupt
+  *            @arg SMARTCARD_IT_IDLE: Idle line detection interrupt
+  *            @arg SMARTCARD_IT_PE:   Parity Error interrupt
+  *            @arg SMARTCARD_IT_ERR:  Error interrupt(Frame error, noise error, overrun error)
+  * @retval None
+  */
+#define __HAL_SMARTCARD_ENABLE_IT(__HANDLE__, __INTERRUPT__)   ((((__INTERRUPT__) >> 28U) == SMARTCARD_CR1_REG_INDEX)? ((__HANDLE__)->Instance->CR1 |= ((__INTERRUPT__) & SMARTCARD_IT_MASK)): \
+                                                                 ((__HANDLE__)->Instance->CR3 |= ((__INTERRUPT__) & SMARTCARD_IT_MASK)))
+
+/** @brief  Disable the specified SmartCard interrupt.
+  * @param  __HANDLE__ specifies the SMARTCARD Handle.
+  *         SMARTCARD Handle selects the USARTx peripheral (USART availability and x value depending on device).
+  * @param  __INTERRUPT__ specifies the SMARTCARD interrupt to disable.
+  *          This parameter can be one of the following values:
+  *            @arg SMARTCARD_IT_TXE:  Transmit Data Register empty interrupt
+  *            @arg SMARTCARD_IT_TC:   Transmission complete interrupt
+  *            @arg SMARTCARD_IT_RXNE: Receive Data register not empty interrupt
+  *            @arg SMARTCARD_IT_IDLE: Idle line detection interrupt
+  *            @arg SMARTCARD_IT_PE:   Parity Error interrupt
+  *            @arg SMARTCARD_IT_ERR:  Error interrupt(Frame error, noise error, overrun error)
+  * @retval None
+  */
+#define __HAL_SMARTCARD_DISABLE_IT(__HANDLE__, __INTERRUPT__)  ((((__INTERRUPT__) >> 28U) == SMARTCARD_CR1_REG_INDEX)? ((__HANDLE__)->Instance->CR1 &= ~((__INTERRUPT__) & SMARTCARD_IT_MASK)): \
+                                                                 ((__HANDLE__)->Instance->CR3 &= ~ ((__INTERRUPT__) & SMARTCARD_IT_MASK)))
+
+/** @brief  Checks whether the specified SmartCard interrupt has occurred or not.
+  * @param  __HANDLE__ specifies the SmartCard Handle.
+  * @param  __IT__ specifies the SMARTCARD interrupt source to check.
+  *          This parameter can be one of the following values:
+  *            @arg SMARTCARD_IT_TXE: Transmit Data Register empty interrupt
+  *            @arg SMARTCARD_IT_TC:  Transmission complete interrupt
+  *            @arg SMARTCARD_IT_RXNE: Receive Data register not empty interrupt
+  *            @arg SMARTCARD_IT_IDLE: Idle line detection interrupt
+  *            @arg SMARTCARD_IT_ERR: Error interrupt
+  *            @arg SMARTCARD_IT_PE: Parity Error interrupt
+  * @retval The new state of __IT__ (TRUE or FALSE).
+  */
+#define __HAL_SMARTCARD_GET_IT_SOURCE(__HANDLE__, __IT__) (((((__IT__) >> 28U) == SMARTCARD_CR1_REG_INDEX)? (__HANDLE__)->Instance->CR1: (__HANDLE__)->Instance->CR3) & (((uint32_t)(__IT__)) & SMARTCARD_IT_MASK))
+
+/** @brief  Enable the USART associated to the SMARTCARD Handle
+  * @param  __HANDLE__ specifies the SMARTCARD Handle.
+  *         SMARTCARD Handle selects the USARTx peripheral (USART availability and x value depending on device).
+  * @retval None
+  */
+#define __HAL_SMARTCARD_ENABLE(__HANDLE__)  ((__HANDLE__)->Instance->CR1 |=  USART_CR1_UE)
+
+/** @brief  Disable the USART associated to the SMARTCARD Handle
+  * @param  __HANDLE__ specifies the SMARTCARD Handle.
+  *         SMARTCARD Handle selects the USARTx peripheral (USART availability and x value depending on device).
+  * @retval None
+  */
+#define __HAL_SMARTCARD_DISABLE(__HANDLE__)  ((__HANDLE__)->Instance->CR1 &=  ~USART_CR1_UE)
+
+/** @brief  Macros to enable the SmartCard DMA request.
+  * @param  __HANDLE__ specifies the SmartCard Handle.
+  * @param  __REQUEST__ specifies the SmartCard DMA request.
+  *          This parameter can be one of the following values:
+  *            @arg SMARTCARD_DMAREQ_TX: SmartCard DMA transmit request
+  *            @arg SMARTCARD_DMAREQ_RX: SmartCard DMA receive request
+  * @retval None
+  */
+#define __HAL_SMARTCARD_DMA_REQUEST_ENABLE(__HANDLE__, __REQUEST__)    ((__HANDLE__)->Instance->CR3 |=  (__REQUEST__))
+
+/** @brief  Macros to disable the SmartCard DMA request.
+  * @param  __HANDLE__ specifies the SmartCard Handle.
+  * @param  __REQUEST__ specifies the SmartCard DMA request.
+  *          This parameter can be one of the following values:
+  *            @arg SMARTCARD_DMAREQ_TX: SmartCard DMA transmit request
+  *            @arg SMARTCARD_DMAREQ_RX: SmartCard DMA receive request
+  * @retval None
+  */
+#define __HAL_SMARTCARD_DMA_REQUEST_DISABLE(__HANDLE__, __REQUEST__)   ((__HANDLE__)->Instance->CR3 &=  ~(__REQUEST__))
+
+/**
+  * @}
+  */
+
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup SMARTCARD_Exported_Functions
+  * @{
+  */
+
+/** @addtogroup SMARTCARD_Exported_Functions_Group1
+  * @{
+  */
+/* Initialization/de-initialization functions  **********************************/
+HAL_StatusTypeDef HAL_SMARTCARD_Init(SMARTCARD_HandleTypeDef *hsc);
+HAL_StatusTypeDef HAL_SMARTCARD_ReInit(SMARTCARD_HandleTypeDef *hsc);
+HAL_StatusTypeDef HAL_SMARTCARD_DeInit(SMARTCARD_HandleTypeDef *hsc);
+void HAL_SMARTCARD_MspInit(SMARTCARD_HandleTypeDef *hsc);
+void HAL_SMARTCARD_MspDeInit(SMARTCARD_HandleTypeDef *hsc);
+#if (USE_HAL_SMARTCARD_REGISTER_CALLBACKS == 1)
+/* Callbacks Register/UnRegister functions  ***********************************/
+HAL_StatusTypeDef HAL_SMARTCARD_RegisterCallback(SMARTCARD_HandleTypeDef *hsc, HAL_SMARTCARD_CallbackIDTypeDef CallbackID, pSMARTCARD_CallbackTypeDef pCallback);
+HAL_StatusTypeDef HAL_SMARTCARD_UnRegisterCallback(SMARTCARD_HandleTypeDef *hsc, HAL_SMARTCARD_CallbackIDTypeDef CallbackID);
+#endif /* USE_HAL_SMARTCARD_REGISTER_CALLBACKS */
+/**
+  * @}
+  */
+
+/** @addtogroup SMARTCARD_Exported_Functions_Group2
+  * @{
+  */
+/* IO operation functions *******************************************************/
+HAL_StatusTypeDef HAL_SMARTCARD_Transmit(SMARTCARD_HandleTypeDef *hsc, uint8_t *pData, uint16_t Size, uint32_t Timeout);
+HAL_StatusTypeDef HAL_SMARTCARD_Receive(SMARTCARD_HandleTypeDef *hsc, uint8_t *pData, uint16_t Size, uint32_t Timeout);
+HAL_StatusTypeDef HAL_SMARTCARD_Transmit_IT(SMARTCARD_HandleTypeDef *hsc, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_SMARTCARD_Receive_IT(SMARTCARD_HandleTypeDef *hsc, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_SMARTCARD_Transmit_DMA(SMARTCARD_HandleTypeDef *hsc, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_SMARTCARD_Receive_DMA(SMARTCARD_HandleTypeDef *hsc, uint8_t *pData, uint16_t Size);
+/* Transfer Abort functions */
+HAL_StatusTypeDef HAL_SMARTCARD_Abort(SMARTCARD_HandleTypeDef *hsc);
+HAL_StatusTypeDef HAL_SMARTCARD_AbortTransmit(SMARTCARD_HandleTypeDef *hsc);
+HAL_StatusTypeDef HAL_SMARTCARD_AbortReceive(SMARTCARD_HandleTypeDef *hsc);
+HAL_StatusTypeDef HAL_SMARTCARD_Abort_IT(SMARTCARD_HandleTypeDef *hsc);
+HAL_StatusTypeDef HAL_SMARTCARD_AbortTransmit_IT(SMARTCARD_HandleTypeDef *hsc);
+HAL_StatusTypeDef HAL_SMARTCARD_AbortReceive_IT(SMARTCARD_HandleTypeDef *hsc);
+
+void HAL_SMARTCARD_IRQHandler(SMARTCARD_HandleTypeDef *hsc);
+void HAL_SMARTCARD_TxCpltCallback(SMARTCARD_HandleTypeDef *hsc);
+void HAL_SMARTCARD_RxCpltCallback(SMARTCARD_HandleTypeDef *hsc);
+void HAL_SMARTCARD_ErrorCallback(SMARTCARD_HandleTypeDef *hsc);
+void HAL_SMARTCARD_AbortCpltCallback(SMARTCARD_HandleTypeDef *hsc);
+void HAL_SMARTCARD_AbortTransmitCpltCallback(SMARTCARD_HandleTypeDef *hsc);
+void HAL_SMARTCARD_AbortReceiveCpltCallback(SMARTCARD_HandleTypeDef *hsc);
+/**
+  * @}
+  */
+
+/** @addtogroup SMARTCARD_Exported_Functions_Group3
+  * @{
+  */
+/* Peripheral State functions  **************************************************/
+HAL_SMARTCARD_StateTypeDef HAL_SMARTCARD_GetState(SMARTCARD_HandleTypeDef *hsc);
+uint32_t HAL_SMARTCARD_GetError(SMARTCARD_HandleTypeDef *hsc);
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+/* Private types -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private constants ---------------------------------------------------------*/
+/** @defgroup SMARTCARD_Private_Constants SMARTCARD Private Constants
+  * @{
+  */
+
+/** @brief SMARTCARD interruptions flag mask
+  *
+  */
+#define SMARTCARD_IT_MASK                   ((uint32_t) USART_CR1_PEIE | USART_CR1_TXEIE | USART_CR1_TCIE | USART_CR1_RXNEIE | \
+                                                        USART_CR1_IDLEIE | USART_CR3_EIE )
+
+#define SMARTCARD_CR1_REG_INDEX             1U
+#define SMARTCARD_CR3_REG_INDEX             3U
+/**
+  * @}
+  */
+
+/* Private macros --------------------------------------------------------*/
+/** @defgroup SMARTCARD_Private_Macros   SMARTCARD Private Macros
+  * @{
+  */
+#define IS_SMARTCARD_WORD_LENGTH(LENGTH)    ((LENGTH) == SMARTCARD_WORDLENGTH_9B)
+#define IS_SMARTCARD_STOPBITS(STOPBITS)     (((STOPBITS) == SMARTCARD_STOPBITS_0_5) || \
+                                             ((STOPBITS) == SMARTCARD_STOPBITS_1_5))
+#define IS_SMARTCARD_PARITY(PARITY)         (((PARITY) == SMARTCARD_PARITY_EVEN) || \
+                                             ((PARITY) == SMARTCARD_PARITY_ODD))
+#define IS_SMARTCARD_MODE(MODE)             ((((MODE) & 0x0000FFF3U) == 0x00U) && ((MODE) != 0x000000U))
+#define IS_SMARTCARD_POLARITY(CPOL)         (((CPOL) == SMARTCARD_POLARITY_LOW) || ((CPOL) == SMARTCARD_POLARITY_HIGH))
+#define IS_SMARTCARD_PHASE(CPHA)            (((CPHA) == SMARTCARD_PHASE_1EDGE) || ((CPHA) == SMARTCARD_PHASE_2EDGE))
+#define IS_SMARTCARD_LASTBIT(LASTBIT)       (((LASTBIT) == SMARTCARD_LASTBIT_DISABLE) || \
+                                             ((LASTBIT) == SMARTCARD_LASTBIT_ENABLE))
+#define IS_SMARTCARD_NACK_STATE(NACK)       (((NACK) == SMARTCARD_NACK_ENABLE) || \
+                                             ((NACK) == SMARTCARD_NACK_DISABLE))
+#define IS_SMARTCARD_BAUDRATE(BAUDRATE)     ((BAUDRATE) < 4500001U)
+
+#define SMARTCARD_DIV(__PCLK__, __BAUD__)                (((__PCLK__)*25U)/(4U*(__BAUD__)))
+#define SMARTCARD_DIVMANT(__PCLK__, __BAUD__)            (SMARTCARD_DIV((__PCLK__), (__BAUD__))/100U)
+#define SMARTCARD_DIVFRAQ(__PCLK__, __BAUD__)            ((((SMARTCARD_DIV((__PCLK__), (__BAUD__)) - (SMARTCARD_DIVMANT((__PCLK__), (__BAUD__)) * 100U)) * 16U) + 50U) / 100U)
+/* SMARTCARD BRR = mantissa + overflow + fraction
+            = (SMARTCARD DIVMANT << 4) + (SMARTCARD DIVFRAQ & 0xF0) + (SMARTCARD DIVFRAQ & 0x0FU) */
+#define SMARTCARD_BRR(__PCLK__, __BAUD__)       (((SMARTCARD_DIVMANT((__PCLK__), (__BAUD__)) << 4U) + \
+                                                 (SMARTCARD_DIVFRAQ((__PCLK__), (__BAUD__)) & 0xF0U)) + \
+                                                 (SMARTCARD_DIVFRAQ((__PCLK__), (__BAUD__)) & 0x0FU))
+
+/**
+  * @}
+  */
+
+/* Private functions ---------------------------------------------------------*/
+/** @defgroup SMARTCARD_Private_Functions SMARTCARD Private Functions
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F1xx_HAL_SMARTCARD_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_spi.h

@@ -0,0 +1,731 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_hal_spi.h
+  * @author  MCD Application Team
+  * @brief   Header file of SPI HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef STM32F1xx_HAL_SPI_H
+#define STM32F1xx_HAL_SPI_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_hal_def.h"
+
+/** @addtogroup STM32F1xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup SPI
+  * @{
+  */
+
+/* Exported types ------------------------------------------------------------*/
+/** @defgroup SPI_Exported_Types SPI Exported Types
+  * @{
+  */
+
+/**
+  * @brief  SPI Configuration Structure definition
+  */
+typedef struct
+{
+  uint32_t Mode;                /*!< Specifies the SPI operating mode.
+                                     This parameter can be a value of @ref SPI_Mode */
+
+  uint32_t Direction;           /*!< Specifies the SPI bidirectional mode state.
+                                     This parameter can be a value of @ref SPI_Direction */
+
+  uint32_t DataSize;            /*!< Specifies the SPI data size.
+                                     This parameter can be a value of @ref SPI_Data_Size */
+
+  uint32_t CLKPolarity;         /*!< Specifies the serial clock steady state.
+                                     This parameter can be a value of @ref SPI_Clock_Polarity */
+
+  uint32_t CLKPhase;            /*!< Specifies the clock active edge for the bit capture.
+                                     This parameter can be a value of @ref SPI_Clock_Phase */
+
+  uint32_t NSS;                 /*!< Specifies whether the NSS signal is managed by
+                                     hardware (NSS pin) or by software using the SSI bit.
+                                     This parameter can be a value of @ref SPI_Slave_Select_management */
+
+  uint32_t BaudRatePrescaler;   /*!< Specifies the Baud Rate prescaler value which will be
+                                     used to configure the transmit and receive SCK clock.
+                                     This parameter can be a value of @ref SPI_BaudRate_Prescaler
+                                     @note The communication clock is derived from the master
+                                     clock. The slave clock does not need to be set. */
+
+  uint32_t FirstBit;            /*!< Specifies whether data transfers start from MSB or LSB bit.
+                                     This parameter can be a value of @ref SPI_MSB_LSB_transmission */
+
+  uint32_t TIMode;              /*!< Specifies if the TI mode is enabled or not.
+                                     This parameter can be a value of @ref SPI_TI_mode */
+
+  uint32_t CRCCalculation;      /*!< Specifies if the CRC calculation is enabled or not.
+                                     This parameter can be a value of @ref SPI_CRC_Calculation */
+
+  uint32_t CRCPolynomial;       /*!< Specifies the polynomial used for the CRC calculation.
+                                     This parameter must be an odd number between Min_Data = 1 and Max_Data = 65535 */
+} SPI_InitTypeDef;
+
+/**
+  * @brief  HAL SPI State structure definition
+  */
+typedef enum
+{
+  HAL_SPI_STATE_RESET      = 0x00U,    /*!< Peripheral not Initialized                         */
+  HAL_SPI_STATE_READY      = 0x01U,    /*!< Peripheral Initialized and ready for use           */
+  HAL_SPI_STATE_BUSY       = 0x02U,    /*!< an internal process is ongoing                     */
+  HAL_SPI_STATE_BUSY_TX    = 0x03U,    /*!< Data Transmission process is ongoing               */
+  HAL_SPI_STATE_BUSY_RX    = 0x04U,    /*!< Data Reception process is ongoing                  */
+  HAL_SPI_STATE_BUSY_TX_RX = 0x05U,    /*!< Data Transmission and Reception process is ongoing */
+  HAL_SPI_STATE_ERROR      = 0x06U,    /*!< SPI error state                                    */
+  HAL_SPI_STATE_ABORT      = 0x07U     /*!< SPI abort is ongoing                               */
+} HAL_SPI_StateTypeDef;
+
+/**
+  * @brief  SPI handle Structure definition
+  */
+typedef struct __SPI_HandleTypeDef
+{
+  SPI_TypeDef                *Instance;      /*!< SPI registers base address               */
+
+  SPI_InitTypeDef            Init;           /*!< SPI communication parameters             */
+
+  uint8_t                    *pTxBuffPtr;    /*!< Pointer to SPI Tx transfer Buffer        */
+
+  uint16_t                   TxXferSize;     /*!< SPI Tx Transfer size                     */
+
+  __IO uint16_t              TxXferCount;    /*!< SPI Tx Transfer Counter                  */
+
+  uint8_t                    *pRxBuffPtr;    /*!< Pointer to SPI Rx transfer Buffer        */
+
+  uint16_t                   RxXferSize;     /*!< SPI Rx Transfer size                     */
+
+  __IO uint16_t              RxXferCount;    /*!< SPI Rx Transfer Counter                  */
+
+  void (*RxISR)(struct __SPI_HandleTypeDef *hspi);   /*!< function pointer on Rx ISR       */
+
+  void (*TxISR)(struct __SPI_HandleTypeDef *hspi);   /*!< function pointer on Tx ISR       */
+
+  DMA_HandleTypeDef          *hdmatx;        /*!< SPI Tx DMA Handle parameters             */
+
+  DMA_HandleTypeDef          *hdmarx;        /*!< SPI Rx DMA Handle parameters             */
+
+  HAL_LockTypeDef            Lock;           /*!< Locking object                           */
+
+  __IO HAL_SPI_StateTypeDef  State;          /*!< SPI communication state                  */
+
+  __IO uint32_t              ErrorCode;      /*!< SPI Error code                           */
+
+#if (USE_HAL_SPI_REGISTER_CALLBACKS == 1U)
+  void (* TxCpltCallback)(struct __SPI_HandleTypeDef *hspi);             /*!< SPI Tx Completed callback          */
+  void (* RxCpltCallback)(struct __SPI_HandleTypeDef *hspi);             /*!< SPI Rx Completed callback          */
+  void (* TxRxCpltCallback)(struct __SPI_HandleTypeDef *hspi);           /*!< SPI TxRx Completed callback        */
+  void (* TxHalfCpltCallback)(struct __SPI_HandleTypeDef *hspi);         /*!< SPI Tx Half Completed callback     */
+  void (* RxHalfCpltCallback)(struct __SPI_HandleTypeDef *hspi);         /*!< SPI Rx Half Completed callback     */
+  void (* TxRxHalfCpltCallback)(struct __SPI_HandleTypeDef *hspi);       /*!< SPI TxRx Half Completed callback   */
+  void (* ErrorCallback)(struct __SPI_HandleTypeDef *hspi);              /*!< SPI Error callback                 */
+  void (* AbortCpltCallback)(struct __SPI_HandleTypeDef *hspi);          /*!< SPI Abort callback                 */
+  void (* MspInitCallback)(struct __SPI_HandleTypeDef *hspi);            /*!< SPI Msp Init callback              */
+  void (* MspDeInitCallback)(struct __SPI_HandleTypeDef *hspi);          /*!< SPI Msp DeInit callback            */
+
+#endif  /* USE_HAL_SPI_REGISTER_CALLBACKS */
+} SPI_HandleTypeDef;
+
+#if (USE_HAL_SPI_REGISTER_CALLBACKS == 1U)
+/**
+  * @brief  HAL SPI Callback ID enumeration definition
+  */
+typedef enum
+{
+  HAL_SPI_TX_COMPLETE_CB_ID             = 0x00U,    /*!< SPI Tx Completed callback ID         */
+  HAL_SPI_RX_COMPLETE_CB_ID             = 0x01U,    /*!< SPI Rx Completed callback ID         */
+  HAL_SPI_TX_RX_COMPLETE_CB_ID          = 0x02U,    /*!< SPI TxRx Completed callback ID       */
+  HAL_SPI_TX_HALF_COMPLETE_CB_ID        = 0x03U,    /*!< SPI Tx Half Completed callback ID    */
+  HAL_SPI_RX_HALF_COMPLETE_CB_ID        = 0x04U,    /*!< SPI Rx Half Completed callback ID    */
+  HAL_SPI_TX_RX_HALF_COMPLETE_CB_ID     = 0x05U,    /*!< SPI TxRx Half Completed callback ID  */
+  HAL_SPI_ERROR_CB_ID                   = 0x06U,    /*!< SPI Error callback ID                */
+  HAL_SPI_ABORT_CB_ID                   = 0x07U,    /*!< SPI Abort callback ID                */
+  HAL_SPI_MSPINIT_CB_ID                 = 0x08U,    /*!< SPI Msp Init callback ID             */
+  HAL_SPI_MSPDEINIT_CB_ID               = 0x09U     /*!< SPI Msp DeInit callback ID           */
+
+} HAL_SPI_CallbackIDTypeDef;
+
+/**
+  * @brief  HAL SPI Callback pointer definition
+  */
+typedef  void (*pSPI_CallbackTypeDef)(SPI_HandleTypeDef *hspi); /*!< pointer to an SPI callback function */
+
+#endif /* USE_HAL_SPI_REGISTER_CALLBACKS */
+/**
+  * @}
+  */
+
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup SPI_Exported_Constants SPI Exported Constants
+  * @{
+  */
+
+/** @defgroup SPI_Error_Code SPI Error Code
+  * @{
+  */
+#define HAL_SPI_ERROR_NONE              (0x00000000U)   /*!< No error                               */
+#define HAL_SPI_ERROR_MODF              (0x00000001U)   /*!< MODF error                             */
+#define HAL_SPI_ERROR_CRC               (0x00000002U)   /*!< CRC error                              */
+#define HAL_SPI_ERROR_OVR               (0x00000004U)   /*!< OVR error                              */
+#define HAL_SPI_ERROR_DMA               (0x00000010U)   /*!< DMA transfer error                     */
+#define HAL_SPI_ERROR_FLAG              (0x00000020U)   /*!< Error on RXNE/TXE/BSY Flag             */
+#define HAL_SPI_ERROR_ABORT             (0x00000040U)   /*!< Error during SPI Abort procedure       */
+#if (USE_HAL_SPI_REGISTER_CALLBACKS == 1U)
+#define HAL_SPI_ERROR_INVALID_CALLBACK  (0x00000080U)   /*!< Invalid Callback error                 */
+#endif /* USE_HAL_SPI_REGISTER_CALLBACKS */
+/**
+  * @}
+  */
+
+/** @defgroup SPI_Mode SPI Mode
+  * @{
+  */
+#define SPI_MODE_SLAVE                  (0x00000000U)
+#define SPI_MODE_MASTER                 (SPI_CR1_MSTR | SPI_CR1_SSI)
+/**
+  * @}
+  */
+
+/** @defgroup SPI_Direction SPI Direction Mode
+  * @{
+  */
+#define SPI_DIRECTION_2LINES            (0x00000000U)
+#define SPI_DIRECTION_2LINES_RXONLY     SPI_CR1_RXONLY
+#define SPI_DIRECTION_1LINE             SPI_CR1_BIDIMODE
+/**
+  * @}
+  */
+
+/** @defgroup SPI_Data_Size SPI Data Size
+  * @{
+  */
+#define SPI_DATASIZE_8BIT               (0x00000000U)
+#define SPI_DATASIZE_16BIT              SPI_CR1_DFF
+/**
+  * @}
+  */
+
+/** @defgroup SPI_Clock_Polarity SPI Clock Polarity
+  * @{
+  */
+#define SPI_POLARITY_LOW                (0x00000000U)
+#define SPI_POLARITY_HIGH               SPI_CR1_CPOL
+/**
+  * @}
+  */
+
+/** @defgroup SPI_Clock_Phase SPI Clock Phase
+  * @{
+  */
+#define SPI_PHASE_1EDGE                 (0x00000000U)
+#define SPI_PHASE_2EDGE                 SPI_CR1_CPHA
+/**
+  * @}
+  */
+
+/** @defgroup SPI_Slave_Select_management SPI Slave Select Management
+  * @{
+  */
+#define SPI_NSS_SOFT                    SPI_CR1_SSM
+#define SPI_NSS_HARD_INPUT              (0x00000000U)
+#define SPI_NSS_HARD_OUTPUT             (SPI_CR2_SSOE << 16U)
+/**
+  * @}
+  */
+
+/** @defgroup SPI_BaudRate_Prescaler SPI BaudRate Prescaler
+  * @{
+  */
+#define SPI_BAUDRATEPRESCALER_2         (0x00000000U)
+#define SPI_BAUDRATEPRESCALER_4         (SPI_CR1_BR_0)
+#define SPI_BAUDRATEPRESCALER_8         (SPI_CR1_BR_1)
+#define SPI_BAUDRATEPRESCALER_16        (SPI_CR1_BR_1 | SPI_CR1_BR_0)
+#define SPI_BAUDRATEPRESCALER_32        (SPI_CR1_BR_2)
+#define SPI_BAUDRATEPRESCALER_64        (SPI_CR1_BR_2 | SPI_CR1_BR_0)
+#define SPI_BAUDRATEPRESCALER_128       (SPI_CR1_BR_2 | SPI_CR1_BR_1)
+#define SPI_BAUDRATEPRESCALER_256       (SPI_CR1_BR_2 | SPI_CR1_BR_1 | SPI_CR1_BR_0)
+/**
+  * @}
+  */
+
+/** @defgroup SPI_MSB_LSB_transmission SPI MSB LSB Transmission
+  * @{
+  */
+#define SPI_FIRSTBIT_MSB                (0x00000000U)
+#define SPI_FIRSTBIT_LSB                SPI_CR1_LSBFIRST
+/**
+  * @}
+  */
+
+/** @defgroup SPI_TI_mode SPI TI Mode
+  * @{
+  */
+#define SPI_TIMODE_DISABLE              (0x00000000U)
+/**
+  * @}
+  */
+
+/** @defgroup SPI_CRC_Calculation SPI CRC Calculation
+  * @{
+  */
+#define SPI_CRCCALCULATION_DISABLE      (0x00000000U)
+#define SPI_CRCCALCULATION_ENABLE       SPI_CR1_CRCEN
+/**
+  * @}
+  */
+
+/** @defgroup SPI_Interrupt_definition SPI Interrupt Definition
+  * @{
+  */
+#define SPI_IT_TXE                      SPI_CR2_TXEIE
+#define SPI_IT_RXNE                     SPI_CR2_RXNEIE
+#define SPI_IT_ERR                      SPI_CR2_ERRIE
+/**
+  * @}
+  */
+
+/** @defgroup SPI_Flags_definition SPI Flags Definition
+  * @{
+  */
+#define SPI_FLAG_RXNE                   SPI_SR_RXNE   /* SPI status flag: Rx buffer not empty flag       */
+#define SPI_FLAG_TXE                    SPI_SR_TXE    /* SPI status flag: Tx buffer empty flag           */
+#define SPI_FLAG_BSY                    SPI_SR_BSY    /* SPI status flag: Busy flag                      */
+#define SPI_FLAG_CRCERR                 SPI_SR_CRCERR /* SPI Error flag: CRC error flag                  */
+#define SPI_FLAG_MODF                   SPI_SR_MODF   /* SPI Error flag: Mode fault flag                 */
+#define SPI_FLAG_OVR                    SPI_SR_OVR    /* SPI Error flag: Overrun flag                    */
+#define SPI_FLAG_MASK                   (SPI_SR_RXNE | SPI_SR_TXE | SPI_SR_BSY\
+                                         | SPI_SR_CRCERR | SPI_SR_MODF | SPI_SR_OVR)
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Exported macros -----------------------------------------------------------*/
+/** @defgroup SPI_Exported_Macros SPI Exported Macros
+  * @{
+  */
+
+/** @brief  Reset SPI handle state.
+  * @param  __HANDLE__ specifies the SPI Handle.
+  *         This parameter can be SPI where x: 1, 2, or 3 to select the SPI peripheral.
+  * @retval None
+  */
+#if (USE_HAL_SPI_REGISTER_CALLBACKS == 1U)
+#define __HAL_SPI_RESET_HANDLE_STATE(__HANDLE__)                do{                                                  \
+                                                                    (__HANDLE__)->State = HAL_SPI_STATE_RESET;       \
+                                                                    (__HANDLE__)->MspInitCallback = NULL;            \
+                                                                    (__HANDLE__)->MspDeInitCallback = NULL;          \
+                                                                  } while(0)
+#else
+#define __HAL_SPI_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_SPI_STATE_RESET)
+#endif /* USE_HAL_SPI_REGISTER_CALLBACKS */
+
+/** @brief  Enable the specified SPI interrupts.
+  * @param  __HANDLE__ specifies the SPI Handle.
+  *         This parameter can be SPI where x: 1, 2, or 3 to select the SPI peripheral.
+  * @param  __INTERRUPT__ specifies the interrupt source to enable.
+  *         This parameter can be one of the following values:
+  *            @arg SPI_IT_TXE: Tx buffer empty interrupt enable
+  *            @arg SPI_IT_RXNE: RX buffer not empty interrupt enable
+  *            @arg SPI_IT_ERR: Error interrupt enable
+  * @retval None
+  */
+#define __HAL_SPI_ENABLE_IT(__HANDLE__, __INTERRUPT__)   SET_BIT((__HANDLE__)->Instance->CR2, (__INTERRUPT__))
+
+/** @brief  Disable the specified SPI interrupts.
+  * @param  __HANDLE__ specifies the SPI handle.
+  *         This parameter can be SPIx where x: 1, 2, or 3 to select the SPI peripheral.
+  * @param  __INTERRUPT__ specifies the interrupt source to disable.
+  *         This parameter can be one of the following values:
+  *            @arg SPI_IT_TXE: Tx buffer empty interrupt enable
+  *            @arg SPI_IT_RXNE: RX buffer not empty interrupt enable
+  *            @arg SPI_IT_ERR: Error interrupt enable
+  * @retval None
+  */
+#define __HAL_SPI_DISABLE_IT(__HANDLE__, __INTERRUPT__)  CLEAR_BIT((__HANDLE__)->Instance->CR2, (__INTERRUPT__))
+
+/** @brief  Check whether the specified SPI interrupt source is enabled or not.
+  * @param  __HANDLE__ specifies the SPI Handle.
+  *         This parameter can be SPI where x: 1, 2, or 3 to select the SPI peripheral.
+  * @param  __INTERRUPT__ specifies the SPI interrupt source to check.
+  *          This parameter can be one of the following values:
+  *            @arg SPI_IT_TXE: Tx buffer empty interrupt enable
+  *            @arg SPI_IT_RXNE: RX buffer not empty interrupt enable
+  *            @arg SPI_IT_ERR: Error interrupt enable
+  * @retval The new state of __IT__ (TRUE or FALSE).
+  */
+#define __HAL_SPI_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__) ((((__HANDLE__)->Instance->CR2\
+                                                              & (__INTERRUPT__)) == (__INTERRUPT__)) ? SET : RESET)
+
+/** @brief  Check whether the specified SPI flag is set or not.
+  * @param  __HANDLE__ specifies the SPI Handle.
+  *         This parameter can be SPI where x: 1, 2, or 3 to select the SPI peripheral.
+  * @param  __FLAG__ specifies the flag to check.
+  *         This parameter can be one of the following values:
+  *            @arg SPI_FLAG_RXNE: Receive buffer not empty flag
+  *            @arg SPI_FLAG_TXE: Transmit buffer empty flag
+  *            @arg SPI_FLAG_CRCERR: CRC error flag
+  *            @arg SPI_FLAG_MODF: Mode fault flag
+  *            @arg SPI_FLAG_OVR: Overrun flag
+  *            @arg SPI_FLAG_BSY: Busy flag
+  * @retval The new state of __FLAG__ (TRUE or FALSE).
+  */
+#define __HAL_SPI_GET_FLAG(__HANDLE__, __FLAG__) ((((__HANDLE__)->Instance->SR) & (__FLAG__)) == (__FLAG__))
+
+/** @brief  Clear the SPI CRCERR pending flag.
+  * @param  __HANDLE__ specifies the SPI Handle.
+  *         This parameter can be SPI where x: 1, 2, or 3 to select the SPI peripheral.
+  * @retval None
+  */
+#define __HAL_SPI_CLEAR_CRCERRFLAG(__HANDLE__) ((__HANDLE__)->Instance->SR = (uint16_t)(~SPI_FLAG_CRCERR))
+
+/** @brief  Clear the SPI MODF pending flag.
+  * @param  __HANDLE__ specifies the SPI Handle.
+  *         This parameter can be SPI where x: 1, 2, or 3 to select the SPI peripheral.
+  * @retval None
+  */
+#define __HAL_SPI_CLEAR_MODFFLAG(__HANDLE__)             \
+  do{                                                    \
+    __IO uint32_t tmpreg_modf = 0x00U;                   \
+    tmpreg_modf = (__HANDLE__)->Instance->SR;            \
+    CLEAR_BIT((__HANDLE__)->Instance->CR1, SPI_CR1_SPE); \
+    UNUSED(tmpreg_modf);                                 \
+  } while(0U)
+
+/** @brief  Clear the SPI OVR pending flag.
+  * @param  __HANDLE__ specifies the SPI Handle.
+  *         This parameter can be SPI where x: 1, 2, or 3 to select the SPI peripheral.
+  * @retval None
+  */
+#define __HAL_SPI_CLEAR_OVRFLAG(__HANDLE__)        \
+  do{                                              \
+    __IO uint32_t tmpreg_ovr = 0x00U;              \
+    tmpreg_ovr = (__HANDLE__)->Instance->DR;       \
+    tmpreg_ovr = (__HANDLE__)->Instance->SR;       \
+    UNUSED(tmpreg_ovr);                            \
+  } while(0U)
+
+/** @brief  Enable the SPI peripheral.
+  * @param  __HANDLE__ specifies the SPI Handle.
+  *         This parameter can be SPI where x: 1, 2, or 3 to select the SPI peripheral.
+  * @retval None
+  */
+#define __HAL_SPI_ENABLE(__HANDLE__)  SET_BIT((__HANDLE__)->Instance->CR1, SPI_CR1_SPE)
+
+/** @brief  Disable the SPI peripheral.
+  * @param  __HANDLE__ specifies the SPI Handle.
+  *         This parameter can be SPI where x: 1, 2, or 3 to select the SPI peripheral.
+  * @retval None
+  */
+#define __HAL_SPI_DISABLE(__HANDLE__) CLEAR_BIT((__HANDLE__)->Instance->CR1, SPI_CR1_SPE)
+
+/**
+  * @}
+  */
+
+/* Private constants ---------------------------------------------------------*/
+/** @defgroup SPI_Private_Constants SPI Private Constants
+  * @{
+  */
+#define SPI_INVALID_CRC_ERROR     0U          /* CRC error wrongly detected */
+#define SPI_VALID_CRC_ERROR       1U          /* CRC error is true */
+/**
+  * @}
+  */
+
+/* Private macros ------------------------------------------------------------*/
+/** @defgroup SPI_Private_Macros SPI Private Macros
+  * @{
+  */
+
+/** @brief  Set the SPI transmit-only mode.
+  * @param  __HANDLE__ specifies the SPI Handle.
+  *         This parameter can be SPI where x: 1, 2, or 3 to select the SPI peripheral.
+  * @retval None
+  */
+#define SPI_1LINE_TX(__HANDLE__)  SET_BIT((__HANDLE__)->Instance->CR1, SPI_CR1_BIDIOE)
+
+/** @brief  Set the SPI receive-only mode.
+  * @param  __HANDLE__ specifies the SPI Handle.
+  *         This parameter can be SPI where x: 1, 2, or 3 to select the SPI peripheral.
+  * @retval None
+  */
+#define SPI_1LINE_RX(__HANDLE__)  CLEAR_BIT((__HANDLE__)->Instance->CR1, SPI_CR1_BIDIOE)
+
+/** @brief  Reset the CRC calculation of the SPI.
+  * @param  __HANDLE__ specifies the SPI Handle.
+  *         This parameter can be SPI where x: 1, 2, or 3 to select the SPI peripheral.
+  * @retval None
+  */
+#define SPI_RESET_CRC(__HANDLE__) do{CLEAR_BIT((__HANDLE__)->Instance->CR1, SPI_CR1_CRCEN);\
+                                       SET_BIT((__HANDLE__)->Instance->CR1, SPI_CR1_CRCEN);}while(0U)
+
+/** @brief  Check whether the specified SPI flag is set or not.
+  * @param  __SR__  copy of SPI SR register.
+  * @param  __FLAG__ specifies the flag to check.
+  *         This parameter can be one of the following values:
+  *            @arg SPI_FLAG_RXNE: Receive buffer not empty flag
+  *            @arg SPI_FLAG_TXE: Transmit buffer empty flag
+  *            @arg SPI_FLAG_CRCERR: CRC error flag
+  *            @arg SPI_FLAG_MODF: Mode fault flag
+  *            @arg SPI_FLAG_OVR: Overrun flag
+  *            @arg SPI_FLAG_BSY: Busy flag
+  * @retval SET or RESET.
+  */
+#define SPI_CHECK_FLAG(__SR__, __FLAG__) ((((__SR__) & ((__FLAG__) & SPI_FLAG_MASK)) == \
+                                          ((__FLAG__) & SPI_FLAG_MASK)) ? SET : RESET)
+
+/** @brief  Check whether the specified SPI Interrupt is set or not.
+  * @param  __CR2__  copy of SPI CR2 register.
+  * @param  __INTERRUPT__ specifies the SPI interrupt source to check.
+  *         This parameter can be one of the following values:
+  *            @arg SPI_IT_TXE: Tx buffer empty interrupt enable
+  *            @arg SPI_IT_RXNE: RX buffer not empty interrupt enable
+  *            @arg SPI_IT_ERR: Error interrupt enable
+  * @retval SET or RESET.
+  */
+#define SPI_CHECK_IT_SOURCE(__CR2__, __INTERRUPT__) ((((__CR2__) & (__INTERRUPT__)) == \
+                                                     (__INTERRUPT__)) ? SET : RESET)
+
+/** @brief  Checks if SPI Mode parameter is in allowed range.
+  * @param  __MODE__ specifies the SPI Mode.
+  *         This parameter can be a value of @ref SPI_Mode
+  * @retval None
+  */
+#define IS_SPI_MODE(__MODE__)      (((__MODE__) == SPI_MODE_SLAVE)   || \
+                                    ((__MODE__) == SPI_MODE_MASTER))
+
+/** @brief  Checks if SPI Direction Mode parameter is in allowed range.
+  * @param  __MODE__ specifies the SPI Direction Mode.
+  *         This parameter can be a value of @ref SPI_Direction
+  * @retval None
+  */
+#define IS_SPI_DIRECTION(__MODE__) (((__MODE__) == SPI_DIRECTION_2LINES)        || \
+                                    ((__MODE__) == SPI_DIRECTION_2LINES_RXONLY) || \
+                                    ((__MODE__) == SPI_DIRECTION_1LINE))
+
+/** @brief  Checks if SPI Direction Mode parameter is 2 lines.
+  * @param  __MODE__ specifies the SPI Direction Mode.
+  * @retval None
+  */
+#define IS_SPI_DIRECTION_2LINES(__MODE__) ((__MODE__) == SPI_DIRECTION_2LINES)
+
+/** @brief  Checks if SPI Direction Mode parameter is 1 or 2 lines.
+  * @param  __MODE__ specifies the SPI Direction Mode.
+  * @retval None
+  */
+#define IS_SPI_DIRECTION_2LINES_OR_1LINE(__MODE__) (((__MODE__) == SPI_DIRECTION_2LINES) || \
+                                                    ((__MODE__) == SPI_DIRECTION_1LINE))
+
+/** @brief  Checks if SPI Data Size parameter is in allowed range.
+  * @param  __DATASIZE__ specifies the SPI Data Size.
+  *         This parameter can be a value of @ref SPI_Data_Size
+  * @retval None
+  */
+#define IS_SPI_DATASIZE(__DATASIZE__) (((__DATASIZE__) == SPI_DATASIZE_16BIT) || \
+                                       ((__DATASIZE__) == SPI_DATASIZE_8BIT))
+
+/** @brief  Checks if SPI Serial clock steady state parameter is in allowed range.
+  * @param  __CPOL__ specifies the SPI serial clock steady state.
+  *         This parameter can be a value of @ref SPI_Clock_Polarity
+  * @retval None
+  */
+#define IS_SPI_CPOL(__CPOL__)      (((__CPOL__) == SPI_POLARITY_LOW) || \
+                                    ((__CPOL__) == SPI_POLARITY_HIGH))
+
+/** @brief  Checks if SPI Clock Phase parameter is in allowed range.
+  * @param  __CPHA__ specifies the SPI Clock Phase.
+  *         This parameter can be a value of @ref SPI_Clock_Phase
+  * @retval None
+  */
+#define IS_SPI_CPHA(__CPHA__)      (((__CPHA__) == SPI_PHASE_1EDGE) || \
+                                    ((__CPHA__) == SPI_PHASE_2EDGE))
+
+/** @brief  Checks if SPI Slave Select parameter is in allowed range.
+  * @param  __NSS__ specifies the SPI Slave Select management parameter.
+  *         This parameter can be a value of @ref SPI_Slave_Select_management
+  * @retval None
+  */
+#define IS_SPI_NSS(__NSS__)        (((__NSS__) == SPI_NSS_SOFT)       || \
+                                    ((__NSS__) == SPI_NSS_HARD_INPUT) || \
+                                    ((__NSS__) == SPI_NSS_HARD_OUTPUT))
+
+/** @brief  Checks if SPI Baudrate prescaler parameter is in allowed range.
+  * @param  __PRESCALER__ specifies the SPI Baudrate prescaler.
+  *         This parameter can be a value of @ref SPI_BaudRate_Prescaler
+  * @retval None
+  */
+#define IS_SPI_BAUDRATE_PRESCALER(__PRESCALER__) (((__PRESCALER__) == SPI_BAUDRATEPRESCALER_2)   || \
+                                                  ((__PRESCALER__) == SPI_BAUDRATEPRESCALER_4)   || \
+                                                  ((__PRESCALER__) == SPI_BAUDRATEPRESCALER_8)   || \
+                                                  ((__PRESCALER__) == SPI_BAUDRATEPRESCALER_16)  || \
+                                                  ((__PRESCALER__) == SPI_BAUDRATEPRESCALER_32)  || \
+                                                  ((__PRESCALER__) == SPI_BAUDRATEPRESCALER_64)  || \
+                                                  ((__PRESCALER__) == SPI_BAUDRATEPRESCALER_128) || \
+                                                  ((__PRESCALER__) == SPI_BAUDRATEPRESCALER_256))
+
+/** @brief  Checks if SPI MSB LSB transmission parameter is in allowed range.
+  * @param  __BIT__ specifies the SPI MSB LSB transmission (whether data transfer starts from MSB or LSB bit).
+  *         This parameter can be a value of @ref SPI_MSB_LSB_transmission
+  * @retval None
+  */
+#define IS_SPI_FIRST_BIT(__BIT__)  (((__BIT__) == SPI_FIRSTBIT_MSB) || \
+                                    ((__BIT__) == SPI_FIRSTBIT_LSB))
+
+/** @brief  Checks if SPI TI mode parameter is disabled.
+  * @param  __MODE__ SPI_TIMODE_DISABLE. Device not support Ti Mode.
+  *         This parameter can be a value of @ref SPI_TI_mode
+  * @retval None
+  */
+#define IS_SPI_TIMODE(__MODE__) ((__MODE__) == SPI_TIMODE_DISABLE)
+
+/** @brief  Checks if SPI CRC calculation enabled state is in allowed range.
+  * @param  __CALCULATION__ specifies the SPI CRC calculation enable state.
+  *         This parameter can be a value of @ref SPI_CRC_Calculation
+  * @retval None
+  */
+#define IS_SPI_CRC_CALCULATION(__CALCULATION__) (((__CALCULATION__) == SPI_CRCCALCULATION_DISABLE) || \
+                                                 ((__CALCULATION__) == SPI_CRCCALCULATION_ENABLE))
+
+/** @brief  Checks if SPI polynomial value to be used for the CRC calculation, is in allowed range.
+  * @param  __POLYNOMIAL__ specifies the SPI polynomial value to be used for the CRC calculation.
+  *         This parameter must be a number between Min_Data = 0 and Max_Data = 65535
+  * @retval None
+  */
+#define IS_SPI_CRC_POLYNOMIAL(__POLYNOMIAL__) (((__POLYNOMIAL__) >= 0x1U)    && \
+                                               ((__POLYNOMIAL__) <= 0xFFFFU) && \
+                                              (((__POLYNOMIAL__)&0x1U) != 0U))
+
+/** @brief  Checks if DMA handle is valid.
+  * @param  __HANDLE__ specifies a DMA Handle.
+  * @retval None
+  */
+#define IS_SPI_DMA_HANDLE(__HANDLE__) ((__HANDLE__) != NULL)
+
+/**
+  * @}
+  */
+
+/* Private functions ---------------------------------------------------------*/
+/** @defgroup SPI_Private_Functions SPI Private Functions
+  * @{
+  */
+uint8_t SPI_ISCRCErrorValid(SPI_HandleTypeDef *hspi);
+/**
+  * @}
+  */
+
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup SPI_Exported_Functions
+  * @{
+  */
+
+/** @addtogroup SPI_Exported_Functions_Group1
+  * @{
+  */
+/* Initialization/de-initialization functions  ********************************/
+HAL_StatusTypeDef HAL_SPI_Init(SPI_HandleTypeDef *hspi);
+HAL_StatusTypeDef HAL_SPI_DeInit(SPI_HandleTypeDef *hspi);
+void HAL_SPI_MspInit(SPI_HandleTypeDef *hspi);
+void HAL_SPI_MspDeInit(SPI_HandleTypeDef *hspi);
+
+/* Callbacks Register/UnRegister functions  ***********************************/
+#if (USE_HAL_SPI_REGISTER_CALLBACKS == 1U)
+HAL_StatusTypeDef HAL_SPI_RegisterCallback(SPI_HandleTypeDef *hspi, HAL_SPI_CallbackIDTypeDef CallbackID, pSPI_CallbackTypeDef pCallback);
+HAL_StatusTypeDef HAL_SPI_UnRegisterCallback(SPI_HandleTypeDef *hspi, HAL_SPI_CallbackIDTypeDef CallbackID);
+#endif /* USE_HAL_SPI_REGISTER_CALLBACKS */
+/**
+  * @}
+  */
+
+/** @addtogroup SPI_Exported_Functions_Group2
+  * @{
+  */
+/* I/O operation functions  ***************************************************/
+HAL_StatusTypeDef HAL_SPI_Transmit(SPI_HandleTypeDef *hspi, uint8_t *pData, uint16_t Size, uint32_t Timeout);
+HAL_StatusTypeDef HAL_SPI_Receive(SPI_HandleTypeDef *hspi, uint8_t *pData, uint16_t Size, uint32_t Timeout);
+HAL_StatusTypeDef HAL_SPI_TransmitReceive(SPI_HandleTypeDef *hspi, uint8_t *pTxData, uint8_t *pRxData, uint16_t Size,
+                                          uint32_t Timeout);
+HAL_StatusTypeDef HAL_SPI_Transmit_IT(SPI_HandleTypeDef *hspi, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_SPI_Receive_IT(SPI_HandleTypeDef *hspi, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_SPI_TransmitReceive_IT(SPI_HandleTypeDef *hspi, uint8_t *pTxData, uint8_t *pRxData,
+                                             uint16_t Size);
+HAL_StatusTypeDef HAL_SPI_Transmit_DMA(SPI_HandleTypeDef *hspi, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_SPI_Receive_DMA(SPI_HandleTypeDef *hspi, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_SPI_TransmitReceive_DMA(SPI_HandleTypeDef *hspi, uint8_t *pTxData, uint8_t *pRxData,
+                                              uint16_t Size);
+HAL_StatusTypeDef HAL_SPI_DMAPause(SPI_HandleTypeDef *hspi);
+HAL_StatusTypeDef HAL_SPI_DMAResume(SPI_HandleTypeDef *hspi);
+HAL_StatusTypeDef HAL_SPI_DMAStop(SPI_HandleTypeDef *hspi);
+/* Transfer Abort functions */
+HAL_StatusTypeDef HAL_SPI_Abort(SPI_HandleTypeDef *hspi);
+HAL_StatusTypeDef HAL_SPI_Abort_IT(SPI_HandleTypeDef *hspi);
+
+void HAL_SPI_IRQHandler(SPI_HandleTypeDef *hspi);
+void HAL_SPI_TxCpltCallback(SPI_HandleTypeDef *hspi);
+void HAL_SPI_RxCpltCallback(SPI_HandleTypeDef *hspi);
+void HAL_SPI_TxRxCpltCallback(SPI_HandleTypeDef *hspi);
+void HAL_SPI_TxHalfCpltCallback(SPI_HandleTypeDef *hspi);
+void HAL_SPI_RxHalfCpltCallback(SPI_HandleTypeDef *hspi);
+void HAL_SPI_TxRxHalfCpltCallback(SPI_HandleTypeDef *hspi);
+void HAL_SPI_ErrorCallback(SPI_HandleTypeDef *hspi);
+void HAL_SPI_AbortCpltCallback(SPI_HandleTypeDef *hspi);
+/**
+  * @}
+  */
+
+/** @addtogroup SPI_Exported_Functions_Group3
+  * @{
+  */
+/* Peripheral State and Error functions ***************************************/
+HAL_SPI_StateTypeDef HAL_SPI_GetState(SPI_HandleTypeDef *hspi);
+uint32_t             HAL_SPI_GetError(SPI_HandleTypeDef *hspi);
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* STM32F1xx_HAL_SPI_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_sram.h

@@ -0,0 +1,235 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_hal_sram.h
+  * @author  MCD Application Team
+  * @brief   Header file of SRAM HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                       opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef STM32F1xx_HAL_SRAM_H
+#define STM32F1xx_HAL_SRAM_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+#if defined(FSMC_BANK1)
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_ll_fsmc.h"
+
+/** @addtogroup STM32F1xx_HAL_Driver
+  * @{
+  */
+/** @addtogroup SRAM
+  * @{
+  */
+
+/* Exported typedef ----------------------------------------------------------*/
+
+/** @defgroup SRAM_Exported_Types SRAM Exported Types
+  * @{
+  */
+/**
+  * @brief  HAL SRAM State structures definition
+  */
+typedef enum
+{
+  HAL_SRAM_STATE_RESET     = 0x00U,  /*!< SRAM not yet initialized or disabled           */
+  HAL_SRAM_STATE_READY     = 0x01U,  /*!< SRAM initialized and ready for use             */
+  HAL_SRAM_STATE_BUSY      = 0x02U,  /*!< SRAM internal process is ongoing               */
+  HAL_SRAM_STATE_ERROR     = 0x03U,  /*!< SRAM error state                               */
+  HAL_SRAM_STATE_PROTECTED = 0x04U   /*!< SRAM peripheral NORSRAM device write protected */
+
+} HAL_SRAM_StateTypeDef;
+
+/**
+  * @brief  SRAM handle Structure definition
+  */
+#if (USE_HAL_SRAM_REGISTER_CALLBACKS == 1)
+typedef struct __SRAM_HandleTypeDef
+#else
+typedef struct
+#endif /* USE_HAL_SRAM_REGISTER_CALLBACKS  */
+{
+  FSMC_NORSRAM_TypeDef           *Instance;  /*!< Register base address                        */
+
+  FSMC_NORSRAM_EXTENDED_TypeDef  *Extended;  /*!< Extended mode register base address          */
+
+  FSMC_NORSRAM_InitTypeDef       Init;       /*!< SRAM device control configuration parameters */
+
+  HAL_LockTypeDef               Lock;       /*!< SRAM locking object                          */
+
+  __IO HAL_SRAM_StateTypeDef    State;      /*!< SRAM device access state                     */
+
+  DMA_HandleTypeDef             *hdma;      /*!< Pointer DMA handler                          */
+
+#if (USE_HAL_SRAM_REGISTER_CALLBACKS == 1)
+  void (* MspInitCallback)(struct __SRAM_HandleTypeDef *hsram);               /*!< SRAM Msp Init callback              */
+  void (* MspDeInitCallback)(struct __SRAM_HandleTypeDef *hsram);             /*!< SRAM Msp DeInit callback            */
+  void (* DmaXferCpltCallback)(DMA_HandleTypeDef *hdma);                      /*!< SRAM DMA Xfer Complete callback     */
+  void (* DmaXferErrorCallback)(DMA_HandleTypeDef *hdma);                     /*!< SRAM DMA Xfer Error callback        */
+#endif /* USE_HAL_SRAM_REGISTER_CALLBACKS  */
+} SRAM_HandleTypeDef;
+
+#if (USE_HAL_SRAM_REGISTER_CALLBACKS == 1)
+/**
+  * @brief  HAL SRAM Callback ID enumeration definition
+  */
+typedef enum
+{
+  HAL_SRAM_MSP_INIT_CB_ID       = 0x00U,  /*!< SRAM MspInit Callback ID           */
+  HAL_SRAM_MSP_DEINIT_CB_ID     = 0x01U,  /*!< SRAM MspDeInit Callback ID         */
+  HAL_SRAM_DMA_XFER_CPLT_CB_ID  = 0x02U,  /*!< SRAM DMA Xfer Complete Callback ID */
+  HAL_SRAM_DMA_XFER_ERR_CB_ID   = 0x03U   /*!< SRAM DMA Xfer Complete Callback ID */
+} HAL_SRAM_CallbackIDTypeDef;
+
+/**
+  * @brief  HAL SRAM Callback pointer definition
+  */
+typedef void (*pSRAM_CallbackTypeDef)(SRAM_HandleTypeDef *hsram);
+typedef void (*pSRAM_DmaCallbackTypeDef)(DMA_HandleTypeDef *hdma);
+#endif /* USE_HAL_SRAM_REGISTER_CALLBACKS  */
+/**
+  * @}
+  */
+
+/* Exported constants --------------------------------------------------------*/
+/* Exported macro ------------------------------------------------------------*/
+
+/** @defgroup SRAM_Exported_Macros SRAM Exported Macros
+  * @{
+  */
+
+/** @brief Reset SRAM handle state
+  * @param  __HANDLE__ SRAM handle
+  * @retval None
+  */
+#if (USE_HAL_SRAM_REGISTER_CALLBACKS == 1)
+#define __HAL_SRAM_RESET_HANDLE_STATE(__HANDLE__)         do {                                             \
+                                                               (__HANDLE__)->State = HAL_SRAM_STATE_RESET; \
+                                                               (__HANDLE__)->MspInitCallback = NULL;       \
+                                                               (__HANDLE__)->MspDeInitCallback = NULL;     \
+                                                             } while(0)
+#else
+#define __HAL_SRAM_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_SRAM_STATE_RESET)
+#endif /* USE_HAL_SRAM_REGISTER_CALLBACKS  */
+
+/**
+  * @}
+  */
+
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup SRAM_Exported_Functions SRAM Exported Functions
+  * @{
+  */
+
+/** @addtogroup SRAM_Exported_Functions_Group1 Initialization and de-initialization functions
+  * @{
+  */
+
+/* Initialization/de-initialization functions  ********************************/
+HAL_StatusTypeDef HAL_SRAM_Init(SRAM_HandleTypeDef *hsram, FSMC_NORSRAM_TimingTypeDef *Timing,
+                                FSMC_NORSRAM_TimingTypeDef *ExtTiming);
+HAL_StatusTypeDef HAL_SRAM_DeInit(SRAM_HandleTypeDef *hsram);
+void HAL_SRAM_MspInit(SRAM_HandleTypeDef *hsram);
+void HAL_SRAM_MspDeInit(SRAM_HandleTypeDef *hsram);
+
+/**
+  * @}
+  */
+
+/** @addtogroup SRAM_Exported_Functions_Group2 Input Output and memory control functions
+  * @{
+  */
+
+/* I/O operation functions  ***************************************************/
+HAL_StatusTypeDef HAL_SRAM_Read_8b(SRAM_HandleTypeDef *hsram, uint32_t *pAddress, uint8_t *pDstBuffer,
+                                   uint32_t BufferSize);
+HAL_StatusTypeDef HAL_SRAM_Write_8b(SRAM_HandleTypeDef *hsram, uint32_t *pAddress, uint8_t *pSrcBuffer,
+                                    uint32_t BufferSize);
+HAL_StatusTypeDef HAL_SRAM_Read_16b(SRAM_HandleTypeDef *hsram, uint32_t *pAddress, uint16_t *pDstBuffer,
+                                    uint32_t BufferSize);
+HAL_StatusTypeDef HAL_SRAM_Write_16b(SRAM_HandleTypeDef *hsram, uint32_t *pAddress, uint16_t *pSrcBuffer,
+                                     uint32_t BufferSize);
+HAL_StatusTypeDef HAL_SRAM_Read_32b(SRAM_HandleTypeDef *hsram, uint32_t *pAddress, uint32_t *pDstBuffer,
+                                    uint32_t BufferSize);
+HAL_StatusTypeDef HAL_SRAM_Write_32b(SRAM_HandleTypeDef *hsram, uint32_t *pAddress, uint32_t *pSrcBuffer,
+                                     uint32_t BufferSize);
+HAL_StatusTypeDef HAL_SRAM_Read_DMA(SRAM_HandleTypeDef *hsram, uint32_t *pAddress, uint32_t *pDstBuffer,
+                                    uint32_t BufferSize);
+HAL_StatusTypeDef HAL_SRAM_Write_DMA(SRAM_HandleTypeDef *hsram, uint32_t *pAddress, uint32_t *pSrcBuffer,
+                                     uint32_t BufferSize);
+
+void HAL_SRAM_DMA_XferCpltCallback(DMA_HandleTypeDef *hdma);
+void HAL_SRAM_DMA_XferErrorCallback(DMA_HandleTypeDef *hdma);
+
+#if (USE_HAL_SRAM_REGISTER_CALLBACKS == 1)
+/* SRAM callback registering/unregistering */
+HAL_StatusTypeDef HAL_SRAM_RegisterCallback(SRAM_HandleTypeDef *hsram, HAL_SRAM_CallbackIDTypeDef CallbackId,
+                                            pSRAM_CallbackTypeDef pCallback);
+HAL_StatusTypeDef HAL_SRAM_UnRegisterCallback(SRAM_HandleTypeDef *hsram, HAL_SRAM_CallbackIDTypeDef CallbackId);
+HAL_StatusTypeDef HAL_SRAM_RegisterDmaCallback(SRAM_HandleTypeDef *hsram, HAL_SRAM_CallbackIDTypeDef CallbackId,
+                                               pSRAM_DmaCallbackTypeDef pCallback);
+#endif /* USE_HAL_SRAM_REGISTER_CALLBACKS  */
+
+/**
+  * @}
+  */
+
+/** @addtogroup SRAM_Exported_Functions_Group3 Control functions
+  * @{
+  */
+
+/* SRAM Control functions  ****************************************************/
+HAL_StatusTypeDef HAL_SRAM_WriteOperation_Enable(SRAM_HandleTypeDef *hsram);
+HAL_StatusTypeDef HAL_SRAM_WriteOperation_Disable(SRAM_HandleTypeDef *hsram);
+
+/**
+  * @}
+  */
+
+/** @addtogroup SRAM_Exported_Functions_Group4 Peripheral State functions
+  * @{
+  */
+
+/* SRAM  State functions ******************************************************/
+HAL_SRAM_StateTypeDef HAL_SRAM_GetState(SRAM_HandleTypeDef *hsram);
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#endif /* FSMC_BANK1 */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* STM32F1xx_HAL_SRAM_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_tim_ex.h

@@ -0,0 +1,262 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_hal_tim_ex.h
+  * @author  MCD Application Team
+  * @brief   Header file of TIM HAL Extended module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef STM32F1xx_HAL_TIM_EX_H
+#define STM32F1xx_HAL_TIM_EX_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_hal_def.h"
+
+/** @addtogroup STM32F1xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup TIMEx
+  * @{
+  */
+
+/* Exported types ------------------------------------------------------------*/
+/** @defgroup TIMEx_Exported_Types TIM Extended Exported Types
+  * @{
+  */
+
+/**
+  * @brief  TIM Hall sensor Configuration Structure definition
+  */
+
+typedef struct
+{
+  uint32_t IC1Polarity;         /*!< Specifies the active edge of the input signal.
+                                     This parameter can be a value of @ref TIM_Input_Capture_Polarity */
+
+  uint32_t IC1Prescaler;        /*!< Specifies the Input Capture Prescaler.
+                                     This parameter can be a value of @ref TIM_Input_Capture_Prescaler */
+
+  uint32_t IC1Filter;           /*!< Specifies the input capture filter.
+                                     This parameter can be a number between Min_Data = 0x0 and Max_Data = 0xF */
+
+  uint32_t Commutation_Delay;   /*!< Specifies the pulse value to be loaded into the Capture Compare Register.
+                                     This parameter can be a number between Min_Data = 0x0000 and Max_Data = 0xFFFF */
+} TIM_HallSensor_InitTypeDef;
+/**
+  * @}
+  */
+/* End of exported types -----------------------------------------------------*/
+
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup TIMEx_Exported_Constants TIM Extended Exported Constants
+  * @{
+  */
+
+/** @defgroup TIMEx_Remap TIM Extended Remapping
+  * @{
+  */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+/* End of exported constants -------------------------------------------------*/
+
+/* Exported macro ------------------------------------------------------------*/
+/** @defgroup TIMEx_Exported_Macros TIM Extended Exported Macros
+  * @{
+  */
+
+/**
+  * @}
+  */
+/* End of exported macro -----------------------------------------------------*/
+
+/* Private macro -------------------------------------------------------------*/
+/** @defgroup TIMEx_Private_Macros TIM Extended Private Macros
+  * @{
+  */
+
+/**
+  * @}
+  */
+/* End of private macro ------------------------------------------------------*/
+
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup TIMEx_Exported_Functions TIM Extended Exported Functions
+  * @{
+  */
+
+/** @addtogroup TIMEx_Exported_Functions_Group1 Extended Timer Hall Sensor functions
+  *  @brief    Timer Hall Sensor functions
+  * @{
+  */
+/*  Timer Hall Sensor functions  **********************************************/
+HAL_StatusTypeDef HAL_TIMEx_HallSensor_Init(TIM_HandleTypeDef *htim, TIM_HallSensor_InitTypeDef *sConfig);
+HAL_StatusTypeDef HAL_TIMEx_HallSensor_DeInit(TIM_HandleTypeDef *htim);
+
+void HAL_TIMEx_HallSensor_MspInit(TIM_HandleTypeDef *htim);
+void HAL_TIMEx_HallSensor_MspDeInit(TIM_HandleTypeDef *htim);
+
+/* Blocking mode: Polling */
+HAL_StatusTypeDef HAL_TIMEx_HallSensor_Start(TIM_HandleTypeDef *htim);
+HAL_StatusTypeDef HAL_TIMEx_HallSensor_Stop(TIM_HandleTypeDef *htim);
+/* Non-Blocking mode: Interrupt */
+HAL_StatusTypeDef HAL_TIMEx_HallSensor_Start_IT(TIM_HandleTypeDef *htim);
+HAL_StatusTypeDef HAL_TIMEx_HallSensor_Stop_IT(TIM_HandleTypeDef *htim);
+/* Non-Blocking mode: DMA */
+HAL_StatusTypeDef HAL_TIMEx_HallSensor_Start_DMA(TIM_HandleTypeDef *htim, uint32_t *pData, uint16_t Length);
+HAL_StatusTypeDef HAL_TIMEx_HallSensor_Stop_DMA(TIM_HandleTypeDef *htim);
+/**
+  * @}
+  */
+
+/** @addtogroup TIMEx_Exported_Functions_Group2 Extended Timer Complementary Output Compare functions
+  *  @brief   Timer Complementary Output Compare functions
+  * @{
+  */
+/*  Timer Complementary Output Compare functions  *****************************/
+/* Blocking mode: Polling */
+HAL_StatusTypeDef HAL_TIMEx_OCN_Start(TIM_HandleTypeDef *htim, uint32_t Channel);
+HAL_StatusTypeDef HAL_TIMEx_OCN_Stop(TIM_HandleTypeDef *htim, uint32_t Channel);
+
+/* Non-Blocking mode: Interrupt */
+HAL_StatusTypeDef HAL_TIMEx_OCN_Start_IT(TIM_HandleTypeDef *htim, uint32_t Channel);
+HAL_StatusTypeDef HAL_TIMEx_OCN_Stop_IT(TIM_HandleTypeDef *htim, uint32_t Channel);
+
+/* Non-Blocking mode: DMA */
+HAL_StatusTypeDef HAL_TIMEx_OCN_Start_DMA(TIM_HandleTypeDef *htim, uint32_t Channel, uint32_t *pData, uint16_t Length);
+HAL_StatusTypeDef HAL_TIMEx_OCN_Stop_DMA(TIM_HandleTypeDef *htim, uint32_t Channel);
+/**
+  * @}
+  */
+
+/** @addtogroup TIMEx_Exported_Functions_Group3 Extended Timer Complementary PWM functions
+  *  @brief    Timer Complementary PWM functions
+  * @{
+  */
+/*  Timer Complementary PWM functions  ****************************************/
+/* Blocking mode: Polling */
+HAL_StatusTypeDef HAL_TIMEx_PWMN_Start(TIM_HandleTypeDef *htim, uint32_t Channel);
+HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop(TIM_HandleTypeDef *htim, uint32_t Channel);
+
+/* Non-Blocking mode: Interrupt */
+HAL_StatusTypeDef HAL_TIMEx_PWMN_Start_IT(TIM_HandleTypeDef *htim, uint32_t Channel);
+HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop_IT(TIM_HandleTypeDef *htim, uint32_t Channel);
+/* Non-Blocking mode: DMA */
+HAL_StatusTypeDef HAL_TIMEx_PWMN_Start_DMA(TIM_HandleTypeDef *htim, uint32_t Channel, uint32_t *pData, uint16_t Length);
+HAL_StatusTypeDef HAL_TIMEx_PWMN_Stop_DMA(TIM_HandleTypeDef *htim, uint32_t Channel);
+/**
+  * @}
+  */
+
+/** @addtogroup TIMEx_Exported_Functions_Group4 Extended Timer Complementary One Pulse functions
+  *  @brief    Timer Complementary One Pulse functions
+  * @{
+  */
+/*  Timer Complementary One Pulse functions  **********************************/
+/* Blocking mode: Polling */
+HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Start(TIM_HandleTypeDef *htim, uint32_t OutputChannel);
+HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Stop(TIM_HandleTypeDef *htim, uint32_t OutputChannel);
+
+/* Non-Blocking mode: Interrupt */
+HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Start_IT(TIM_HandleTypeDef *htim, uint32_t OutputChannel);
+HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Stop_IT(TIM_HandleTypeDef *htim, uint32_t OutputChannel);
+/**
+  * @}
+  */
+
+/** @addtogroup TIMEx_Exported_Functions_Group5 Extended Peripheral Control functions
+  *  @brief    Peripheral Control functions
+  * @{
+  */
+/* Extended Control functions  ************************************************/
+HAL_StatusTypeDef HAL_TIMEx_ConfigCommutEvent(TIM_HandleTypeDef *htim, uint32_t  InputTrigger,
+                                              uint32_t  CommutationSource);
+HAL_StatusTypeDef HAL_TIMEx_ConfigCommutEvent_IT(TIM_HandleTypeDef *htim, uint32_t  InputTrigger,
+                                                 uint32_t  CommutationSource);
+HAL_StatusTypeDef HAL_TIMEx_ConfigCommutEvent_DMA(TIM_HandleTypeDef *htim, uint32_t  InputTrigger,
+                                                  uint32_t  CommutationSource);
+HAL_StatusTypeDef HAL_TIMEx_MasterConfigSynchronization(TIM_HandleTypeDef *htim,
+                                                        TIM_MasterConfigTypeDef *sMasterConfig);
+HAL_StatusTypeDef HAL_TIMEx_ConfigBreakDeadTime(TIM_HandleTypeDef *htim,
+                                                TIM_BreakDeadTimeConfigTypeDef *sBreakDeadTimeConfig);
+HAL_StatusTypeDef HAL_TIMEx_RemapConfig(TIM_HandleTypeDef *htim, uint32_t Remap);
+/**
+  * @}
+  */
+
+/** @addtogroup TIMEx_Exported_Functions_Group6 Extended Callbacks functions
+  * @brief    Extended Callbacks functions
+  * @{
+  */
+/* Extended Callback **********************************************************/
+void HAL_TIMEx_CommutCallback(TIM_HandleTypeDef *htim);
+void HAL_TIMEx_CommutHalfCpltCallback(TIM_HandleTypeDef *htim);
+void HAL_TIMEx_BreakCallback(TIM_HandleTypeDef *htim);
+/**
+  * @}
+  */
+
+/** @addtogroup TIMEx_Exported_Functions_Group7 Extended Peripheral State functions
+  * @brief    Extended Peripheral State functions
+  * @{
+  */
+/* Extended Peripheral State functions  ***************************************/
+HAL_TIM_StateTypeDef HAL_TIMEx_HallSensor_GetState(TIM_HandleTypeDef *htim);
+HAL_TIM_ChannelStateTypeDef HAL_TIMEx_GetChannelNState(TIM_HandleTypeDef *htim,  uint32_t ChannelN);
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+/* End of exported functions -------------------------------------------------*/
+
+/* Private functions----------------------------------------------------------*/
+/** @addtogroup TIMEx_Private_Functions TIMEx Private Functions
+  * @{
+  */
+void TIMEx_DMACommutationCplt(DMA_HandleTypeDef *hdma);
+void TIMEx_DMACommutationHalfCplt(DMA_HandleTypeDef *hdma);
+/**
+  * @}
+  */
+/* End of private functions --------------------------------------------------*/
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+
+#endif /* STM32F1xx_HAL_TIM_EX_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_uart.h

@@ -0,0 +1,887 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_hal_uart.h
+  * @author  MCD Application Team
+  * @brief   Header file of UART HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F1xx_HAL_UART_H
+#define __STM32F1xx_HAL_UART_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_hal_def.h"
+
+/** @addtogroup STM32F1xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup UART
+  * @{
+  */
+
+/* Exported types ------------------------------------------------------------*/
+/** @defgroup UART_Exported_Types UART Exported Types
+  * @{
+  */
+
+/**
+  * @brief UART Init Structure definition
+  */
+typedef struct
+{
+  uint32_t BaudRate;                  /*!< This member configures the UART communication baud rate.
+                                           The baud rate is computed using the following formula:
+                                           - IntegerDivider = ((PCLKx) / (16 * (huart->Init.BaudRate)))
+                                           - FractionalDivider = ((IntegerDivider - ((uint32_t) IntegerDivider)) * 16) + 0.5 */
+
+  uint32_t WordLength;                /*!< Specifies the number of data bits transmitted or received in a frame.
+                                           This parameter can be a value of @ref UART_Word_Length */
+
+  uint32_t StopBits;                  /*!< Specifies the number of stop bits transmitted.
+                                           This parameter can be a value of @ref UART_Stop_Bits */
+
+  uint32_t Parity;                    /*!< Specifies the parity mode.
+                                           This parameter can be a value of @ref UART_Parity
+                                           @note When parity is enabled, the computed parity is inserted
+                                                 at the MSB position of the transmitted data (9th bit when
+                                                 the word length is set to 9 data bits; 8th bit when the
+                                                 word length is set to 8 data bits). */
+
+  uint32_t Mode;                      /*!< Specifies whether the Receive or Transmit mode is enabled or disabled.
+                                           This parameter can be a value of @ref UART_Mode */
+
+  uint32_t HwFlowCtl;                 /*!< Specifies whether the hardware flow control mode is enabled or disabled.
+                                           This parameter can be a value of @ref UART_Hardware_Flow_Control */
+
+  uint32_t OverSampling;              /*!< Specifies whether the Over sampling 8 is enabled or disabled, to achieve higher speed (up to fPCLK/8).
+                                           This parameter can be a value of @ref UART_Over_Sampling. This feature is only available 
+                                           on STM32F100xx family, so OverSampling parameter should always be set to 16. */
+} UART_InitTypeDef;
+
+/**
+  * @brief HAL UART State structures definition
+  * @note  HAL UART State value is a combination of 2 different substates: gState and RxState.
+  *        - gState contains UART state information related to global Handle management
+  *          and also information related to Tx operations.
+  *          gState value coding follow below described bitmap :
+  *          b7-b6  Error information
+  *             00 : No Error
+  *             01 : (Not Used)
+  *             10 : Timeout
+  *             11 : Error
+  *          b5     Peripheral initialization status
+  *             0  : Reset (Peripheral not initialized)
+  *             1  : Init done (Peripheral initialized. HAL UART Init function already called)
+  *          b4-b3  (not used)
+  *             xx : Should be set to 00
+  *          b2     Intrinsic process state
+  *             0  : Ready
+  *             1  : Busy (Peripheral busy with some configuration or internal operations)
+  *          b1     (not used)
+  *             x  : Should be set to 0
+  *          b0     Tx state
+  *             0  : Ready (no Tx operation ongoing)
+  *             1  : Busy (Tx operation ongoing)
+  *        - RxState contains information related to Rx operations.
+  *          RxState value coding follow below described bitmap :
+  *          b7-b6  (not used)
+  *             xx : Should be set to 00
+  *          b5     Peripheral initialization status
+  *             0  : Reset (Peripheral not initialized)
+  *             1  : Init done (Peripheral initialized)
+  *          b4-b2  (not used)
+  *            xxx : Should be set to 000
+  *          b1     Rx state
+  *             0  : Ready (no Rx operation ongoing)
+  *             1  : Busy (Rx operation ongoing)
+  *          b0     (not used)
+  *             x  : Should be set to 0.
+  */
+typedef enum
+{
+  HAL_UART_STATE_RESET             = 0x00U,    /*!< Peripheral is not yet Initialized
+                                                   Value is allowed for gState and RxState */
+  HAL_UART_STATE_READY             = 0x20U,    /*!< Peripheral Initialized and ready for use
+                                                   Value is allowed for gState and RxState */
+  HAL_UART_STATE_BUSY              = 0x24U,    /*!< an internal process is ongoing
+                                                   Value is allowed for gState only */
+  HAL_UART_STATE_BUSY_TX           = 0x21U,    /*!< Data Transmission process is ongoing
+                                                   Value is allowed for gState only */
+  HAL_UART_STATE_BUSY_RX           = 0x22U,    /*!< Data Reception process is ongoing
+                                                   Value is allowed for RxState only */
+  HAL_UART_STATE_BUSY_TX_RX        = 0x23U,    /*!< Data Transmission and Reception process is ongoing
+                                                   Not to be used for neither gState nor RxState.
+                                                   Value is result of combination (Or) between gState and RxState values */
+  HAL_UART_STATE_TIMEOUT           = 0xA0U,    /*!< Timeout state
+                                                   Value is allowed for gState only */
+  HAL_UART_STATE_ERROR             = 0xE0U     /*!< Error
+                                                   Value is allowed for gState only */
+} HAL_UART_StateTypeDef;
+
+/**
+  * @brief HAL UART Reception type definition
+  * @note  HAL UART Reception type value aims to identify which type of Reception is ongoing.
+  *        It is expected to admit following values :
+  *           HAL_UART_RECEPTION_STANDARD         = 0x00U,
+  *           HAL_UART_RECEPTION_TOIDLE           = 0x01U,
+  */
+typedef uint32_t HAL_UART_RxTypeTypeDef;
+
+/**
+  * @brief  UART handle Structure definition
+  */
+typedef struct __UART_HandleTypeDef
+{
+  USART_TypeDef                 *Instance;        /*!< UART registers base address        */
+
+  UART_InitTypeDef              Init;             /*!< UART communication parameters      */
+
+  uint8_t                       *pTxBuffPtr;      /*!< Pointer to UART Tx transfer Buffer */
+
+  uint16_t                      TxXferSize;       /*!< UART Tx Transfer size              */
+
+  __IO uint16_t                 TxXferCount;      /*!< UART Tx Transfer Counter           */
+
+  uint8_t                       *pRxBuffPtr;      /*!< Pointer to UART Rx transfer Buffer */
+
+  uint16_t                      RxXferSize;       /*!< UART Rx Transfer size              */
+
+  __IO uint16_t                 RxXferCount;      /*!< UART Rx Transfer Counter           */
+
+  __IO HAL_UART_RxTypeTypeDef ReceptionType;      /*!< Type of ongoing reception          */
+
+  DMA_HandleTypeDef             *hdmatx;          /*!< UART Tx DMA Handle parameters      */
+
+  DMA_HandleTypeDef             *hdmarx;          /*!< UART Rx DMA Handle parameters      */
+
+  HAL_LockTypeDef               Lock;             /*!< Locking object                     */
+
+  __IO HAL_UART_StateTypeDef    gState;           /*!< UART state information related to global Handle management
+                                                       and also related to Tx operations.
+                                                       This parameter can be a value of @ref HAL_UART_StateTypeDef */
+
+  __IO HAL_UART_StateTypeDef    RxState;          /*!< UART state information related to Rx operations.
+                                                       This parameter can be a value of @ref HAL_UART_StateTypeDef */
+
+  __IO uint32_t                 ErrorCode;        /*!< UART Error code                    */
+
+#if (USE_HAL_UART_REGISTER_CALLBACKS == 1)
+  void (* TxHalfCpltCallback)(struct __UART_HandleTypeDef *huart);        /*!< UART Tx Half Complete Callback        */
+  void (* TxCpltCallback)(struct __UART_HandleTypeDef *huart);            /*!< UART Tx Complete Callback             */
+  void (* RxHalfCpltCallback)(struct __UART_HandleTypeDef *huart);        /*!< UART Rx Half Complete Callback        */
+  void (* RxCpltCallback)(struct __UART_HandleTypeDef *huart);            /*!< UART Rx Complete Callback             */
+  void (* ErrorCallback)(struct __UART_HandleTypeDef *huart);             /*!< UART Error Callback                   */
+  void (* AbortCpltCallback)(struct __UART_HandleTypeDef *huart);         /*!< UART Abort Complete Callback          */
+  void (* AbortTransmitCpltCallback)(struct __UART_HandleTypeDef *huart); /*!< UART Abort Transmit Complete Callback */
+  void (* AbortReceiveCpltCallback)(struct __UART_HandleTypeDef *huart);  /*!< UART Abort Receive Complete Callback  */
+  void (* WakeupCallback)(struct __UART_HandleTypeDef *huart);            /*!< UART Wakeup Callback                  */
+  void (* RxEventCallback)(struct __UART_HandleTypeDef *huart, uint16_t Pos); /*!< UART Reception Event Callback     */
+
+  void (* MspInitCallback)(struct __UART_HandleTypeDef *huart);           /*!< UART Msp Init callback                */
+  void (* MspDeInitCallback)(struct __UART_HandleTypeDef *huart);         /*!< UART Msp DeInit callback              */
+#endif  /* USE_HAL_UART_REGISTER_CALLBACKS */
+
+} UART_HandleTypeDef;
+
+#if (USE_HAL_UART_REGISTER_CALLBACKS == 1)
+/**
+  * @brief  HAL UART Callback ID enumeration definition
+  */
+typedef enum
+{
+  HAL_UART_TX_HALFCOMPLETE_CB_ID         = 0x00U,    /*!< UART Tx Half Complete Callback ID        */
+  HAL_UART_TX_COMPLETE_CB_ID             = 0x01U,    /*!< UART Tx Complete Callback ID             */
+  HAL_UART_RX_HALFCOMPLETE_CB_ID         = 0x02U,    /*!< UART Rx Half Complete Callback ID        */
+  HAL_UART_RX_COMPLETE_CB_ID             = 0x03U,    /*!< UART Rx Complete Callback ID             */
+  HAL_UART_ERROR_CB_ID                   = 0x04U,    /*!< UART Error Callback ID                   */
+  HAL_UART_ABORT_COMPLETE_CB_ID          = 0x05U,    /*!< UART Abort Complete Callback ID          */
+  HAL_UART_ABORT_TRANSMIT_COMPLETE_CB_ID = 0x06U,    /*!< UART Abort Transmit Complete Callback ID */
+  HAL_UART_ABORT_RECEIVE_COMPLETE_CB_ID  = 0x07U,    /*!< UART Abort Receive Complete Callback ID  */
+  HAL_UART_WAKEUP_CB_ID                  = 0x08U,    /*!< UART Wakeup Callback ID                  */
+
+  HAL_UART_MSPINIT_CB_ID                 = 0x0BU,    /*!< UART MspInit callback ID                 */
+  HAL_UART_MSPDEINIT_CB_ID               = 0x0CU     /*!< UART MspDeInit callback ID               */
+
+} HAL_UART_CallbackIDTypeDef;
+
+/**
+  * @brief  HAL UART Callback pointer definition
+  */
+typedef  void (*pUART_CallbackTypeDef)(UART_HandleTypeDef *huart);  /*!< pointer to an UART callback function */
+typedef  void (*pUART_RxEventCallbackTypeDef)(struct __UART_HandleTypeDef *huart, uint16_t Pos);   /*!< pointer to a UART Rx Event specific callback function */
+
+#endif /* USE_HAL_UART_REGISTER_CALLBACKS */
+
+/**
+  * @}
+  */
+
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup UART_Exported_Constants UART Exported Constants
+  * @{
+  */
+
+/** @defgroup UART_Error_Code UART Error Code
+  * @{
+  */
+#define HAL_UART_ERROR_NONE              0x00000000U   /*!< No error            */
+#define HAL_UART_ERROR_PE                0x00000001U   /*!< Parity error        */
+#define HAL_UART_ERROR_NE                0x00000002U   /*!< Noise error         */
+#define HAL_UART_ERROR_FE                0x00000004U   /*!< Frame error         */
+#define HAL_UART_ERROR_ORE               0x00000008U   /*!< Overrun error       */
+#define HAL_UART_ERROR_DMA               0x00000010U   /*!< DMA transfer error  */
+#if (USE_HAL_UART_REGISTER_CALLBACKS == 1)
+#define  HAL_UART_ERROR_INVALID_CALLBACK 0x00000020U   /*!< Invalid Callback error  */
+#endif /* USE_HAL_UART_REGISTER_CALLBACKS */
+/**
+  * @}
+  */
+
+/** @defgroup UART_Word_Length UART Word Length
+  * @{
+  */
+#define UART_WORDLENGTH_8B                  0x00000000U
+#define UART_WORDLENGTH_9B                  ((uint32_t)USART_CR1_M)
+/**
+  * @}
+  */
+
+/** @defgroup UART_Stop_Bits UART Number of Stop Bits
+  * @{
+  */
+#define UART_STOPBITS_1                     0x00000000U
+#define UART_STOPBITS_2                     ((uint32_t)USART_CR2_STOP_1)
+/**
+  * @}
+  */
+
+/** @defgroup UART_Parity UART Parity
+  * @{
+  */
+#define UART_PARITY_NONE                    0x00000000U
+#define UART_PARITY_EVEN                    ((uint32_t)USART_CR1_PCE)
+#define UART_PARITY_ODD                     ((uint32_t)(USART_CR1_PCE | USART_CR1_PS))
+/**
+  * @}
+  */
+
+/** @defgroup UART_Hardware_Flow_Control UART Hardware Flow Control
+  * @{
+  */
+#define UART_HWCONTROL_NONE                  0x00000000U
+#define UART_HWCONTROL_RTS                   ((uint32_t)USART_CR3_RTSE)
+#define UART_HWCONTROL_CTS                   ((uint32_t)USART_CR3_CTSE)
+#define UART_HWCONTROL_RTS_CTS               ((uint32_t)(USART_CR3_RTSE | USART_CR3_CTSE))
+/**
+  * @}
+  */
+
+/** @defgroup UART_Mode UART Transfer Mode
+  * @{
+  */
+#define UART_MODE_RX                        ((uint32_t)USART_CR1_RE)
+#define UART_MODE_TX                        ((uint32_t)USART_CR1_TE)
+#define UART_MODE_TX_RX                     ((uint32_t)(USART_CR1_TE | USART_CR1_RE))
+/**
+  * @}
+  */
+
+/** @defgroup UART_State UART State
+  * @{
+  */
+#define UART_STATE_DISABLE                  0x00000000U
+#define UART_STATE_ENABLE                   ((uint32_t)USART_CR1_UE)
+/**
+  * @}
+  */
+
+/** @defgroup UART_Over_Sampling UART Over Sampling
+  * @{
+  */
+#define UART_OVERSAMPLING_16                    0x00000000U
+#if defined(USART_CR1_OVER8)
+#define UART_OVERSAMPLING_8                     ((uint32_t)USART_CR1_OVER8)
+#endif /* USART_CR1_OVER8 */
+/**
+  * @}
+  */
+
+/** @defgroup UART_LIN_Break_Detection_Length  UART LIN Break Detection Length
+  * @{
+  */
+#define UART_LINBREAKDETECTLENGTH_10B      0x00000000U
+#define UART_LINBREAKDETECTLENGTH_11B      ((uint32_t)USART_CR2_LBDL)
+/**
+  * @}
+  */
+
+/** @defgroup UART_WakeUp_functions  UART Wakeup Functions
+  * @{
+  */
+#define UART_WAKEUPMETHOD_IDLELINE                0x00000000U
+#define UART_WAKEUPMETHOD_ADDRESSMARK             ((uint32_t)USART_CR1_WAKE)
+/**
+  * @}
+  */
+
+/** @defgroup UART_Flags   UART FLags
+  *        Elements values convention: 0xXXXX
+  *           - 0xXXXX  : Flag mask in the SR register
+  * @{
+  */
+#define UART_FLAG_CTS                       ((uint32_t)USART_SR_CTS)
+#define UART_FLAG_LBD                       ((uint32_t)USART_SR_LBD)
+#define UART_FLAG_TXE                       ((uint32_t)USART_SR_TXE)
+#define UART_FLAG_TC                        ((uint32_t)USART_SR_TC)
+#define UART_FLAG_RXNE                      ((uint32_t)USART_SR_RXNE)
+#define UART_FLAG_IDLE                      ((uint32_t)USART_SR_IDLE)
+#define UART_FLAG_ORE                       ((uint32_t)USART_SR_ORE)
+#define UART_FLAG_NE                        ((uint32_t)USART_SR_NE)
+#define UART_FLAG_FE                        ((uint32_t)USART_SR_FE)
+#define UART_FLAG_PE                        ((uint32_t)USART_SR_PE)
+/**
+  * @}
+  */
+
+/** @defgroup UART_Interrupt_definition  UART Interrupt Definitions
+  *        Elements values convention: 0xY000XXXX
+  *           - XXXX  : Interrupt mask (16 bits) in the Y register
+  *           - Y  : Interrupt source register (2bits)
+  *                   - 0001: CR1 register
+  *                   - 0010: CR2 register
+  *                   - 0011: CR3 register
+  * @{
+  */
+
+#define UART_IT_PE                       ((uint32_t)(UART_CR1_REG_INDEX << 28U | USART_CR1_PEIE))
+#define UART_IT_TXE                      ((uint32_t)(UART_CR1_REG_INDEX << 28U | USART_CR1_TXEIE))
+#define UART_IT_TC                       ((uint32_t)(UART_CR1_REG_INDEX << 28U | USART_CR1_TCIE))
+#define UART_IT_RXNE                     ((uint32_t)(UART_CR1_REG_INDEX << 28U | USART_CR1_RXNEIE))
+#define UART_IT_IDLE                     ((uint32_t)(UART_CR1_REG_INDEX << 28U | USART_CR1_IDLEIE))
+
+#define UART_IT_LBD                      ((uint32_t)(UART_CR2_REG_INDEX << 28U | USART_CR2_LBDIE))
+
+#define UART_IT_CTS                      ((uint32_t)(UART_CR3_REG_INDEX << 28U | USART_CR3_CTSIE))
+#define UART_IT_ERR                      ((uint32_t)(UART_CR3_REG_INDEX << 28U | USART_CR3_EIE))
+/**
+  * @}
+  */
+
+/** @defgroup UART_RECEPTION_TYPE_Values  UART Reception type values
+  * @{
+  */
+#define HAL_UART_RECEPTION_STANDARD          (0x00000000U)             /*!< Standard reception                       */
+#define HAL_UART_RECEPTION_TOIDLE            (0x00000001U)             /*!< Reception till completion or IDLE event  */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Exported macro ------------------------------------------------------------*/
+/** @defgroup UART_Exported_Macros UART Exported Macros
+  * @{
+  */
+
+/** @brief Reset UART handle gstate & RxState
+  * @param  __HANDLE__ specifies the UART Handle.
+  *         UART Handle selects the USARTx or UARTy peripheral
+  *         (USART,UART availability and x,y values depending on device).
+  * @retval None
+  */
+#if (USE_HAL_UART_REGISTER_CALLBACKS == 1)
+#define __HAL_UART_RESET_HANDLE_STATE(__HANDLE__)  do{                                                   \
+                                                       (__HANDLE__)->gState = HAL_UART_STATE_RESET;      \
+                                                       (__HANDLE__)->RxState = HAL_UART_STATE_RESET;     \
+                                                       (__HANDLE__)->MspInitCallback = NULL;             \
+                                                       (__HANDLE__)->MspDeInitCallback = NULL;           \
+                                                     } while(0U)
+#else
+#define __HAL_UART_RESET_HANDLE_STATE(__HANDLE__)  do{                                                   \
+                                                       (__HANDLE__)->gState = HAL_UART_STATE_RESET;      \
+                                                       (__HANDLE__)->RxState = HAL_UART_STATE_RESET;     \
+                                                     } while(0U)
+#endif /*USE_HAL_UART_REGISTER_CALLBACKS */
+
+/** @brief  Flushes the UART DR register
+  * @param  __HANDLE__ specifies the UART Handle.
+  *         UART Handle selects the USARTx or UARTy peripheral
+  *         (USART,UART availability and x,y values depending on device).
+  */
+#define __HAL_UART_FLUSH_DRREGISTER(__HANDLE__) ((__HANDLE__)->Instance->DR)
+
+/** @brief  Checks whether the specified UART flag is set or not.
+  * @param  __HANDLE__ specifies the UART Handle.
+  *         UART Handle selects the USARTx or UARTy peripheral
+  *         (USART,UART availability and x,y values depending on device).
+  * @param  __FLAG__ specifies the flag to check.
+  *        This parameter can be one of the following values:
+  *            @arg UART_FLAG_CTS:  CTS Change flag (not available for UART4 and UART5)
+  *            @arg UART_FLAG_LBD:  LIN Break detection flag
+  *            @arg UART_FLAG_TXE:  Transmit data register empty flag
+  *            @arg UART_FLAG_TC:   Transmission Complete flag
+  *            @arg UART_FLAG_RXNE: Receive data register not empty flag
+  *            @arg UART_FLAG_IDLE: Idle Line detection flag
+  *            @arg UART_FLAG_ORE:  Overrun Error flag
+  *            @arg UART_FLAG_NE:   Noise Error flag
+  *            @arg UART_FLAG_FE:   Framing Error flag
+  *            @arg UART_FLAG_PE:   Parity Error flag
+  * @retval The new state of __FLAG__ (TRUE or FALSE).
+  */
+#define __HAL_UART_GET_FLAG(__HANDLE__, __FLAG__) (((__HANDLE__)->Instance->SR & (__FLAG__)) == (__FLAG__))
+
+/** @brief  Clears the specified UART pending flag.
+  * @param  __HANDLE__ specifies the UART Handle.
+  *         UART Handle selects the USARTx or UARTy peripheral
+  *         (USART,UART availability and x,y values depending on device).
+  * @param  __FLAG__ specifies the flag to check.
+  *          This parameter can be any combination of the following values:
+  *            @arg UART_FLAG_CTS:  CTS Change flag (not available for UART4 and UART5).
+  *            @arg UART_FLAG_LBD:  LIN Break detection flag.
+  *            @arg UART_FLAG_TC:   Transmission Complete flag.
+  *            @arg UART_FLAG_RXNE: Receive data register not empty flag.
+  *
+  * @note   PE (Parity error), FE (Framing error), NE (Noise error), ORE (Overrun
+  *          error) and IDLE (Idle line detected) flags are cleared by software
+  *          sequence: a read operation to USART_SR register followed by a read
+  *          operation to USART_DR register.
+  * @note   RXNE flag can be also cleared by a read to the USART_DR register.
+  * @note   TC flag can be also cleared by software sequence: a read operation to
+  *          USART_SR register followed by a write operation to USART_DR register.
+  * @note   TXE flag is cleared only by a write to the USART_DR register.
+  *
+  * @retval None
+  */
+#define __HAL_UART_CLEAR_FLAG(__HANDLE__, __FLAG__) ((__HANDLE__)->Instance->SR = ~(__FLAG__))
+
+/** @brief  Clears the UART PE pending flag.
+  * @param  __HANDLE__ specifies the UART Handle.
+  *         UART Handle selects the USARTx or UARTy peripheral
+  *         (USART,UART availability and x,y values depending on device).
+  * @retval None
+  */
+#define __HAL_UART_CLEAR_PEFLAG(__HANDLE__)     \
+  do{                                           \
+    __IO uint32_t tmpreg = 0x00U;               \
+    tmpreg = (__HANDLE__)->Instance->SR;        \
+    tmpreg = (__HANDLE__)->Instance->DR;        \
+    UNUSED(tmpreg);                             \
+  } while(0U)
+
+/** @brief  Clears the UART FE pending flag.
+  * @param  __HANDLE__ specifies the UART Handle.
+  *         UART Handle selects the USARTx or UARTy peripheral
+  *         (USART,UART availability and x,y values depending on device).
+  * @retval None
+  */
+#define __HAL_UART_CLEAR_FEFLAG(__HANDLE__) __HAL_UART_CLEAR_PEFLAG(__HANDLE__)
+
+/** @brief  Clears the UART NE pending flag.
+  * @param  __HANDLE__ specifies the UART Handle.
+  *         UART Handle selects the USARTx or UARTy peripheral
+  *         (USART,UART availability and x,y values depending on device).
+  * @retval None
+  */
+#define __HAL_UART_CLEAR_NEFLAG(__HANDLE__) __HAL_UART_CLEAR_PEFLAG(__HANDLE__)
+
+/** @brief  Clears the UART ORE pending flag.
+  * @param  __HANDLE__ specifies the UART Handle.
+  *         UART Handle selects the USARTx or UARTy peripheral
+  *         (USART,UART availability and x,y values depending on device).
+  * @retval None
+  */
+#define __HAL_UART_CLEAR_OREFLAG(__HANDLE__) __HAL_UART_CLEAR_PEFLAG(__HANDLE__)
+
+/** @brief  Clears the UART IDLE pending flag.
+  * @param  __HANDLE__ specifies the UART Handle.
+  *         UART Handle selects the USARTx or UARTy peripheral
+  *         (USART,UART availability and x,y values depending on device).
+  * @retval None
+  */
+#define __HAL_UART_CLEAR_IDLEFLAG(__HANDLE__) __HAL_UART_CLEAR_PEFLAG(__HANDLE__)
+
+/** @brief  Enable the specified UART interrupt.
+  * @param  __HANDLE__ specifies the UART Handle.
+  *         UART Handle selects the USARTx or UARTy peripheral
+  *         (USART,UART availability and x,y values depending on device).
+  * @param  __INTERRUPT__ specifies the UART interrupt source to enable.
+  *          This parameter can be one of the following values:
+  *            @arg UART_IT_CTS:  CTS change interrupt
+  *            @arg UART_IT_LBD:  LIN Break detection interrupt
+  *            @arg UART_IT_TXE:  Transmit Data Register empty interrupt
+  *            @arg UART_IT_TC:   Transmission complete interrupt
+  *            @arg UART_IT_RXNE: Receive Data register not empty interrupt
+  *            @arg UART_IT_IDLE: Idle line detection interrupt
+  *            @arg UART_IT_PE:   Parity Error interrupt
+  *            @arg UART_IT_ERR:  Error interrupt(Frame error, noise error, overrun error)
+  * @retval None
+  */
+#define __HAL_UART_ENABLE_IT(__HANDLE__, __INTERRUPT__)   ((((__INTERRUPT__) >> 28U) == UART_CR1_REG_INDEX)? ((__HANDLE__)->Instance->CR1 |= ((__INTERRUPT__) & UART_IT_MASK)): \
+                                                           (((__INTERRUPT__) >> 28U) == UART_CR2_REG_INDEX)? ((__HANDLE__)->Instance->CR2 |= ((__INTERRUPT__) & UART_IT_MASK)): \
+                                                           ((__HANDLE__)->Instance->CR3 |= ((__INTERRUPT__) & UART_IT_MASK)))
+
+/** @brief  Disable the specified UART interrupt.
+  * @param  __HANDLE__ specifies the UART Handle.
+  *         UART Handle selects the USARTx or UARTy peripheral
+  *         (USART,UART availability and x,y values depending on device).
+  * @param  __INTERRUPT__ specifies the UART interrupt source to disable.
+  *          This parameter can be one of the following values:
+  *            @arg UART_IT_CTS:  CTS change interrupt
+  *            @arg UART_IT_LBD:  LIN Break detection interrupt
+  *            @arg UART_IT_TXE:  Transmit Data Register empty interrupt
+  *            @arg UART_IT_TC:   Transmission complete interrupt
+  *            @arg UART_IT_RXNE: Receive Data register not empty interrupt
+  *            @arg UART_IT_IDLE: Idle line detection interrupt
+  *            @arg UART_IT_PE:   Parity Error interrupt
+  *            @arg UART_IT_ERR:  Error interrupt(Frame error, noise error, overrun error)
+  * @retval None
+  */
+#define __HAL_UART_DISABLE_IT(__HANDLE__, __INTERRUPT__)  ((((__INTERRUPT__) >> 28U) == UART_CR1_REG_INDEX)? ((__HANDLE__)->Instance->CR1 &= ~((__INTERRUPT__) & UART_IT_MASK)): \
+                                                           (((__INTERRUPT__) >> 28U) == UART_CR2_REG_INDEX)? ((__HANDLE__)->Instance->CR2 &= ~((__INTERRUPT__) & UART_IT_MASK)): \
+                                                           ((__HANDLE__)->Instance->CR3 &= ~ ((__INTERRUPT__) & UART_IT_MASK)))
+
+/** @brief  Checks whether the specified UART interrupt source is enabled or not.
+  * @param  __HANDLE__ specifies the UART Handle.
+  *         UART Handle selects the USARTx or UARTy peripheral
+  *         (USART,UART availability and x,y values depending on device).
+  * @param  __IT__ specifies the UART interrupt source to check.
+  *          This parameter can be one of the following values:
+  *            @arg UART_IT_CTS: CTS change interrupt (not available for UART4 and UART5)
+  *            @arg UART_IT_LBD: LIN Break detection interrupt
+  *            @arg UART_IT_TXE: Transmit Data Register empty interrupt
+  *            @arg UART_IT_TC:  Transmission complete interrupt
+  *            @arg UART_IT_RXNE: Receive Data register not empty interrupt
+  *            @arg UART_IT_IDLE: Idle line detection interrupt
+  *            @arg UART_IT_ERR: Error interrupt
+  * @retval The new state of __IT__ (TRUE or FALSE).
+  */
+#define __HAL_UART_GET_IT_SOURCE(__HANDLE__, __IT__) (((((__IT__) >> 28U) == UART_CR1_REG_INDEX)? (__HANDLE__)->Instance->CR1:(((((uint32_t)(__IT__)) >> 28U) == UART_CR2_REG_INDEX)? \
+                                                      (__HANDLE__)->Instance->CR2 : (__HANDLE__)->Instance->CR3)) & (((uint32_t)(__IT__)) & UART_IT_MASK))
+
+/** @brief  Enable CTS flow control
+  * @note   This macro allows to enable CTS hardware flow control for a given UART instance,
+  *         without need to call HAL_UART_Init() function.
+  *         As involving direct access to UART registers, usage of this macro should be fully endorsed by user.
+  * @note   As macro is expected to be used for modifying CTS Hw flow control feature activation, without need
+  *         for USART instance Deinit/Init, following conditions for macro call should be fulfilled :
+  *           - UART instance should have already been initialised (through call of HAL_UART_Init() )
+  *           - macro could only be called when corresponding UART instance is disabled (i.e __HAL_UART_DISABLE(__HANDLE__))
+  *             and should be followed by an Enable macro (i.e __HAL_UART_ENABLE(__HANDLE__)).
+  * @param  __HANDLE__ specifies the UART Handle.
+  *         The Handle Instance can be any USARTx (supporting the HW Flow control feature).
+  *         It is used to select the USART peripheral (USART availability and x value depending on device).
+  * @retval None
+  */
+#define __HAL_UART_HWCONTROL_CTS_ENABLE(__HANDLE__)        \
+  do{                                                      \
+    SET_BIT((__HANDLE__)->Instance->CR3, USART_CR3_CTSE);  \
+    (__HANDLE__)->Init.HwFlowCtl |= USART_CR3_CTSE;        \
+  } while(0U)
+
+/** @brief  Disable CTS flow control
+  * @note   This macro allows to disable CTS hardware flow control for a given UART instance,
+  *         without need to call HAL_UART_Init() function.
+  *         As involving direct access to UART registers, usage of this macro should be fully endorsed by user.
+  * @note   As macro is expected to be used for modifying CTS Hw flow control feature activation, without need
+  *         for USART instance Deinit/Init, following conditions for macro call should be fulfilled :
+  *           - UART instance should have already been initialised (through call of HAL_UART_Init() )
+  *           - macro could only be called when corresponding UART instance is disabled (i.e __HAL_UART_DISABLE(__HANDLE__))
+  *             and should be followed by an Enable macro (i.e __HAL_UART_ENABLE(__HANDLE__)).
+  * @param  __HANDLE__ specifies the UART Handle.
+  *         The Handle Instance can be any USARTx (supporting the HW Flow control feature).
+  *         It is used to select the USART peripheral (USART availability and x value depending on device).
+  * @retval None
+  */
+#define __HAL_UART_HWCONTROL_CTS_DISABLE(__HANDLE__)        \
+  do{                                                       \
+    CLEAR_BIT((__HANDLE__)->Instance->CR3, USART_CR3_CTSE); \
+    (__HANDLE__)->Init.HwFlowCtl &= ~(USART_CR3_CTSE);      \
+  } while(0U)
+
+/** @brief  Enable RTS flow control
+  *         This macro allows to enable RTS hardware flow control for a given UART instance,
+  *         without need to call HAL_UART_Init() function.
+  *         As involving direct access to UART registers, usage of this macro should be fully endorsed by user.
+  * @note   As macro is expected to be used for modifying RTS Hw flow control feature activation, without need
+  *         for USART instance Deinit/Init, following conditions for macro call should be fulfilled :
+  *           - UART instance should have already been initialised (through call of HAL_UART_Init() )
+  *           - macro could only be called when corresponding UART instance is disabled (i.e __HAL_UART_DISABLE(__HANDLE__))
+  *             and should be followed by an Enable macro (i.e __HAL_UART_ENABLE(__HANDLE__)).
+  * @param  __HANDLE__ specifies the UART Handle.
+  *         The Handle Instance can be any USARTx (supporting the HW Flow control feature).
+  *         It is used to select the USART peripheral (USART availability and x value depending on device).
+  * @retval None
+  */
+#define __HAL_UART_HWCONTROL_RTS_ENABLE(__HANDLE__)       \
+  do{                                                     \
+    SET_BIT((__HANDLE__)->Instance->CR3, USART_CR3_RTSE); \
+    (__HANDLE__)->Init.HwFlowCtl |= USART_CR3_RTSE;       \
+  } while(0U)
+
+/** @brief  Disable RTS flow control
+  *         This macro allows to disable RTS hardware flow control for a given UART instance,
+  *         without need to call HAL_UART_Init() function.
+  *         As involving direct access to UART registers, usage of this macro should be fully endorsed by user.
+  * @note   As macro is expected to be used for modifying RTS Hw flow control feature activation, without need
+  *         for USART instance Deinit/Init, following conditions for macro call should be fulfilled :
+  *           - UART instance should have already been initialised (through call of HAL_UART_Init() )
+  *           - macro could only be called when corresponding UART instance is disabled (i.e __HAL_UART_DISABLE(__HANDLE__))
+  *             and should be followed by an Enable macro (i.e __HAL_UART_ENABLE(__HANDLE__)).
+  * @param  __HANDLE__ specifies the UART Handle.
+  *         The Handle Instance can be any USARTx (supporting the HW Flow control feature).
+  *         It is used to select the USART peripheral (USART availability and x value depending on device).
+  * @retval None
+  */
+#define __HAL_UART_HWCONTROL_RTS_DISABLE(__HANDLE__)       \
+  do{                                                      \
+    CLEAR_BIT((__HANDLE__)->Instance->CR3, USART_CR3_RTSE);\
+    (__HANDLE__)->Init.HwFlowCtl &= ~(USART_CR3_RTSE);     \
+  } while(0U)
+#if defined(USART_CR3_ONEBIT)
+
+/** @brief  Macro to enable the UART's one bit sample method
+  * @param  __HANDLE__ specifies the UART Handle.
+  * @retval None
+  */
+#define __HAL_UART_ONE_BIT_SAMPLE_ENABLE(__HANDLE__) ((__HANDLE__)->Instance->CR3|= USART_CR3_ONEBIT)
+
+/** @brief  Macro to disable the UART's one bit sample method
+  * @param  __HANDLE__ specifies the UART Handle.
+  * @retval None
+  */
+#define __HAL_UART_ONE_BIT_SAMPLE_DISABLE(__HANDLE__) ((__HANDLE__)->Instance->CR3 &= (uint16_t)~((uint16_t)USART_CR3_ONEBIT))
+#endif /* UART_ONE_BIT_SAMPLE_Feature */
+
+/** @brief  Enable UART
+  * @param  __HANDLE__ specifies the UART Handle.
+  * @retval None
+  */
+#define __HAL_UART_ENABLE(__HANDLE__)               ((__HANDLE__)->Instance->CR1 |=  USART_CR1_UE)
+
+/** @brief  Disable UART
+  * @param  __HANDLE__ specifies the UART Handle.
+  * @retval None
+  */
+#define __HAL_UART_DISABLE(__HANDLE__)              ((__HANDLE__)->Instance->CR1 &=  ~USART_CR1_UE)
+/**
+  * @}
+  */
+
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup UART_Exported_Functions
+  * @{
+  */
+
+/** @addtogroup UART_Exported_Functions_Group1 Initialization and de-initialization functions
+  * @{
+  */
+
+/* Initialization/de-initialization functions  **********************************/
+HAL_StatusTypeDef HAL_UART_Init(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef HAL_HalfDuplex_Init(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef HAL_LIN_Init(UART_HandleTypeDef *huart, uint32_t BreakDetectLength);
+HAL_StatusTypeDef HAL_MultiProcessor_Init(UART_HandleTypeDef *huart, uint8_t Address, uint32_t WakeUpMethod);
+HAL_StatusTypeDef HAL_UART_DeInit(UART_HandleTypeDef *huart);
+void HAL_UART_MspInit(UART_HandleTypeDef *huart);
+void HAL_UART_MspDeInit(UART_HandleTypeDef *huart);
+
+/* Callbacks Register/UnRegister functions  ***********************************/
+#if (USE_HAL_UART_REGISTER_CALLBACKS == 1)
+HAL_StatusTypeDef HAL_UART_RegisterCallback(UART_HandleTypeDef *huart, HAL_UART_CallbackIDTypeDef CallbackID, pUART_CallbackTypeDef pCallback);
+HAL_StatusTypeDef HAL_UART_UnRegisterCallback(UART_HandleTypeDef *huart, HAL_UART_CallbackIDTypeDef CallbackID);
+
+HAL_StatusTypeDef HAL_UART_RegisterRxEventCallback(UART_HandleTypeDef *huart, pUART_RxEventCallbackTypeDef pCallback);
+HAL_StatusTypeDef HAL_UART_UnRegisterRxEventCallback(UART_HandleTypeDef *huart);
+#endif /* USE_HAL_UART_REGISTER_CALLBACKS */
+
+/**
+  * @}
+  */
+
+/** @addtogroup UART_Exported_Functions_Group2 IO operation functions
+  * @{
+  */
+
+/* IO operation functions *******************************************************/
+HAL_StatusTypeDef HAL_UART_Transmit(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size, uint32_t Timeout);
+HAL_StatusTypeDef HAL_UART_Receive(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size, uint32_t Timeout);
+HAL_StatusTypeDef HAL_UART_Transmit_IT(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_UART_Receive_IT(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_UART_Transmit_DMA(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_UART_Receive_DMA(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_UART_DMAPause(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef HAL_UART_DMAResume(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef HAL_UART_DMAStop(UART_HandleTypeDef *huart);
+
+HAL_StatusTypeDef HAL_UARTEx_ReceiveToIdle(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size, uint16_t *RxLen, uint32_t Timeout);
+HAL_StatusTypeDef HAL_UARTEx_ReceiveToIdle_IT(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_UARTEx_ReceiveToIdle_DMA(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size);
+
+/* Transfer Abort functions */
+HAL_StatusTypeDef HAL_UART_Abort(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef HAL_UART_AbortTransmit(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef HAL_UART_AbortReceive(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef HAL_UART_Abort_IT(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef HAL_UART_AbortTransmit_IT(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef HAL_UART_AbortReceive_IT(UART_HandleTypeDef *huart);
+
+void HAL_UART_IRQHandler(UART_HandleTypeDef *huart);
+void HAL_UART_TxCpltCallback(UART_HandleTypeDef *huart);
+void HAL_UART_TxHalfCpltCallback(UART_HandleTypeDef *huart);
+void HAL_UART_RxCpltCallback(UART_HandleTypeDef *huart);
+void HAL_UART_RxHalfCpltCallback(UART_HandleTypeDef *huart);
+void HAL_UART_ErrorCallback(UART_HandleTypeDef *huart);
+void HAL_UART_AbortCpltCallback(UART_HandleTypeDef *huart);
+void HAL_UART_AbortTransmitCpltCallback(UART_HandleTypeDef *huart);
+void HAL_UART_AbortReceiveCpltCallback(UART_HandleTypeDef *huart);
+
+void HAL_UARTEx_RxEventCallback(UART_HandleTypeDef *huart, uint16_t Size);
+
+/**
+  * @}
+  */
+
+/** @addtogroup UART_Exported_Functions_Group3
+  * @{
+  */
+/* Peripheral Control functions  ************************************************/
+HAL_StatusTypeDef HAL_LIN_SendBreak(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef HAL_MultiProcessor_EnterMuteMode(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef HAL_MultiProcessor_ExitMuteMode(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef HAL_HalfDuplex_EnableTransmitter(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef HAL_HalfDuplex_EnableReceiver(UART_HandleTypeDef *huart);
+/**
+  * @}
+  */
+
+/** @addtogroup UART_Exported_Functions_Group4
+  * @{
+  */
+/* Peripheral State functions  **************************************************/
+HAL_UART_StateTypeDef HAL_UART_GetState(UART_HandleTypeDef *huart);
+uint32_t              HAL_UART_GetError(UART_HandleTypeDef *huart);
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+/* Private types -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private constants ---------------------------------------------------------*/
+/** @defgroup UART_Private_Constants UART Private Constants
+  * @{
+  */
+/** @brief UART interruptions flag mask
+  *
+  */
+#define UART_IT_MASK                     0x0000FFFFU
+
+#define UART_CR1_REG_INDEX               1U
+#define UART_CR2_REG_INDEX               2U
+#define UART_CR3_REG_INDEX               3U
+/**
+  * @}
+  */
+
+/* Private macros ------------------------------------------------------------*/
+/** @defgroup UART_Private_Macros UART Private Macros
+  * @{
+  */
+#define IS_UART_WORD_LENGTH(LENGTH) (((LENGTH) == UART_WORDLENGTH_8B) || \
+                                     ((LENGTH) == UART_WORDLENGTH_9B))
+#define IS_UART_LIN_WORD_LENGTH(LENGTH) (((LENGTH) == UART_WORDLENGTH_8B))
+#define IS_UART_STOPBITS(STOPBITS) (((STOPBITS) == UART_STOPBITS_1) || \
+                                    ((STOPBITS) == UART_STOPBITS_2))
+#define IS_UART_PARITY(PARITY) (((PARITY) == UART_PARITY_NONE) || \
+                                ((PARITY) == UART_PARITY_EVEN) || \
+                                ((PARITY) == UART_PARITY_ODD))
+#define IS_UART_HARDWARE_FLOW_CONTROL(CONTROL)\
+                              (((CONTROL) == UART_HWCONTROL_NONE) || \
+                               ((CONTROL) == UART_HWCONTROL_RTS) || \
+                               ((CONTROL) == UART_HWCONTROL_CTS) || \
+                               ((CONTROL) == UART_HWCONTROL_RTS_CTS))
+#define IS_UART_MODE(MODE) ((((MODE) & 0x0000FFF3U) == 0x00U) && ((MODE) != 0x00U))
+#define IS_UART_STATE(STATE) (((STATE) == UART_STATE_DISABLE) || \
+                              ((STATE) == UART_STATE_ENABLE))
+#if defined(USART_CR1_OVER8)
+#define IS_UART_OVERSAMPLING(SAMPLING) (((SAMPLING) == UART_OVERSAMPLING_16) || \
+                                        ((SAMPLING) == UART_OVERSAMPLING_8))
+#endif /* USART_CR1_OVER8 */
+#define IS_UART_LIN_OVERSAMPLING(SAMPLING) (((SAMPLING) == UART_OVERSAMPLING_16))
+#define IS_UART_LIN_BREAK_DETECT_LENGTH(LENGTH) (((LENGTH) == UART_LINBREAKDETECTLENGTH_10B) || \
+                                                 ((LENGTH) == UART_LINBREAKDETECTLENGTH_11B))
+#define IS_UART_WAKEUPMETHOD(WAKEUP) (((WAKEUP) == UART_WAKEUPMETHOD_IDLELINE) || \
+                                      ((WAKEUP) == UART_WAKEUPMETHOD_ADDRESSMARK))
+#define IS_UART_BAUDRATE(BAUDRATE) ((BAUDRATE) <= 4500000U)
+#define IS_UART_ADDRESS(ADDRESS) ((ADDRESS) <= 0x0FU)
+
+#define UART_DIV_SAMPLING16(_PCLK_, _BAUD_)            (((_PCLK_)*25U)/(4U*(_BAUD_)))
+#define UART_DIVMANT_SAMPLING16(_PCLK_, _BAUD_)        (UART_DIV_SAMPLING16((_PCLK_), (_BAUD_))/100U)
+#define UART_DIVFRAQ_SAMPLING16(_PCLK_, _BAUD_)        ((((UART_DIV_SAMPLING16((_PCLK_), (_BAUD_)) - (UART_DIVMANT_SAMPLING16((_PCLK_), (_BAUD_)) * 100U)) * 16U) + 50U) / 100U)
+/* UART BRR = mantissa + overflow + fraction
+            = (UART DIVMANT << 4) + (UART DIVFRAQ & 0xF0) + (UART DIVFRAQ & 0x0FU) */
+#define UART_BRR_SAMPLING16(_PCLK_, _BAUD_)            (((UART_DIVMANT_SAMPLING16((_PCLK_), (_BAUD_)) << 4U) + \
+                                                        (UART_DIVFRAQ_SAMPLING16((_PCLK_), (_BAUD_)) & 0xF0U)) + \
+                                                        (UART_DIVFRAQ_SAMPLING16((_PCLK_), (_BAUD_)) & 0x0FU))
+
+#define UART_DIV_SAMPLING8(_PCLK_, _BAUD_)             (((_PCLK_)*25U)/(2U*(_BAUD_)))
+#define UART_DIVMANT_SAMPLING8(_PCLK_, _BAUD_)         (UART_DIV_SAMPLING8((_PCLK_), (_BAUD_))/100U)
+#define UART_DIVFRAQ_SAMPLING8(_PCLK_, _BAUD_)         ((((UART_DIV_SAMPLING8((_PCLK_), (_BAUD_)) - (UART_DIVMANT_SAMPLING8((_PCLK_), (_BAUD_)) * 100U)) * 8U) + 50U) / 100U)
+/* UART BRR = mantissa + overflow + fraction
+            = (UART DIVMANT << 4) + ((UART DIVFRAQ & 0xF8) << 1) + (UART DIVFRAQ & 0x07U) */
+#define UART_BRR_SAMPLING8(_PCLK_, _BAUD_)             (((UART_DIVMANT_SAMPLING8((_PCLK_), (_BAUD_)) << 4U) + \
+                                                        ((UART_DIVFRAQ_SAMPLING8((_PCLK_), (_BAUD_)) & 0xF8U) << 1U)) + \
+                                                        (UART_DIVFRAQ_SAMPLING8((_PCLK_), (_BAUD_)) & 0x07U))
+
+/**
+  * @}
+  */
+
+/* Private functions ---------------------------------------------------------*/
+/** @defgroup UART_Private_Functions UART Private Functions
+  * @{
+  */
+
+HAL_StatusTypeDef UART_Start_Receive_IT(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef UART_Start_Receive_DMA(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size);
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F1xx_HAL_UART_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_usart.h

@@ -0,0 +1,645 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_hal_usart.h
+  * @author  MCD Application Team
+  * @brief   Header file of USART HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F1xx_HAL_USART_H
+#define __STM32F1xx_HAL_USART_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_hal_def.h"
+
+/** @addtogroup STM32F1xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup USART
+  * @{
+  */
+
+/* Exported types ------------------------------------------------------------*/
+/** @defgroup USART_Exported_Types USART Exported Types
+  * @{
+  */
+
+/**
+  * @brief USART Init Structure definition
+  */
+typedef struct
+{
+  uint32_t BaudRate;                  /*!< This member configures the Usart communication baud rate.
+                                           The baud rate is computed using the following formula:
+                                           - IntegerDivider = ((PCLKx) / (16 * (husart->Init.BaudRate)))
+                                           - FractionalDivider = ((IntegerDivider - ((uint32_t) IntegerDivider)) * 16) + 0.5 */
+
+  uint32_t WordLength;                /*!< Specifies the number of data bits transmitted or received in a frame.
+                                           This parameter can be a value of @ref USART_Word_Length */
+
+  uint32_t StopBits;                  /*!< Specifies the number of stop bits transmitted.
+                                           This parameter can be a value of @ref USART_Stop_Bits */
+
+  uint32_t Parity;                    /*!< Specifies the parity mode.
+                                           This parameter can be a value of @ref USART_Parity
+                                           @note When parity is enabled, the computed parity is inserted
+                                                 at the MSB position of the transmitted data (9th bit when
+                                                 the word length is set to 9 data bits; 8th bit when the
+                                                 word length is set to 8 data bits). */
+
+  uint32_t Mode;                      /*!< Specifies whether the Receive or Transmit mode is enabled or disabled.
+                                           This parameter can be a value of @ref USART_Mode */
+
+  uint32_t CLKPolarity;               /*!< Specifies the steady state of the serial clock.
+                                           This parameter can be a value of @ref USART_Clock_Polarity */
+
+  uint32_t CLKPhase;                  /*!< Specifies the clock transition on which the bit capture is made.
+                                           This parameter can be a value of @ref USART_Clock_Phase */
+
+  uint32_t CLKLastBit;                /*!< Specifies whether the clock pulse corresponding to the last transmitted
+                                           data bit (MSB) has to be output on the SCLK pin in synchronous mode.
+                                           This parameter can be a value of @ref USART_Last_Bit */
+} USART_InitTypeDef;
+
+/**
+  * @brief HAL State structures definition
+  */
+typedef enum
+{
+  HAL_USART_STATE_RESET             = 0x00U,    /*!< Peripheral is not yet Initialized   */
+  HAL_USART_STATE_READY             = 0x01U,    /*!< Peripheral Initialized and ready for use */
+  HAL_USART_STATE_BUSY              = 0x02U,    /*!< an internal process is ongoing */
+  HAL_USART_STATE_BUSY_TX           = 0x12U,    /*!< Data Transmission process is ongoing */
+  HAL_USART_STATE_BUSY_RX           = 0x22U,    /*!< Data Reception process is ongoing */
+  HAL_USART_STATE_BUSY_TX_RX        = 0x32U,    /*!< Data Transmission Reception process is ongoing */
+  HAL_USART_STATE_TIMEOUT           = 0x03U,    /*!< Timeout state */
+  HAL_USART_STATE_ERROR             = 0x04U     /*!< Error */
+} HAL_USART_StateTypeDef;
+
+/**
+  * @brief  USART handle Structure definition
+  */
+typedef struct __USART_HandleTypeDef
+{
+  USART_TypeDef                 *Instance;        /*!< USART registers base address        */
+
+  USART_InitTypeDef             Init;             /*!< Usart communication parameters      */
+
+  uint8_t                       *pTxBuffPtr;      /*!< Pointer to Usart Tx transfer Buffer */
+
+  uint16_t                      TxXferSize;       /*!< Usart Tx Transfer size              */
+
+  __IO uint16_t                 TxXferCount;      /*!< Usart Tx Transfer Counter           */
+
+  uint8_t                       *pRxBuffPtr;      /*!< Pointer to Usart Rx transfer Buffer */
+
+  uint16_t                      RxXferSize;       /*!< Usart Rx Transfer size              */
+
+  __IO uint16_t                 RxXferCount;      /*!< Usart Rx Transfer Counter           */
+
+  DMA_HandleTypeDef             *hdmatx;          /*!< Usart Tx DMA Handle parameters      */
+
+  DMA_HandleTypeDef             *hdmarx;          /*!< Usart Rx DMA Handle parameters      */
+
+  HAL_LockTypeDef                Lock;            /*!< Locking object                      */
+
+  __IO HAL_USART_StateTypeDef    State;           /*!< Usart communication state           */
+
+  __IO uint32_t                  ErrorCode;       /*!< USART Error code                    */
+
+#if (USE_HAL_USART_REGISTER_CALLBACKS == 1)
+  void (* TxHalfCpltCallback)(struct __USART_HandleTypeDef *husart);        /*!< USART Tx Half Complete Callback        */
+  void (* TxCpltCallback)(struct __USART_HandleTypeDef *husart);            /*!< USART Tx Complete Callback             */
+  void (* RxHalfCpltCallback)(struct __USART_HandleTypeDef *husart);        /*!< USART Rx Half Complete Callback        */
+  void (* RxCpltCallback)(struct __USART_HandleTypeDef *husart);            /*!< USART Rx Complete Callback             */
+  void (* TxRxCpltCallback)(struct __USART_HandleTypeDef *husart);          /*!< USART Tx Rx Complete Callback          */
+  void (* ErrorCallback)(struct __USART_HandleTypeDef *husart);             /*!< USART Error Callback                   */
+  void (* AbortCpltCallback)(struct __USART_HandleTypeDef *husart);         /*!< USART Abort Complete Callback          */
+
+  void (* MspInitCallback)(struct __USART_HandleTypeDef *husart);           /*!< USART Msp Init callback                */
+  void (* MspDeInitCallback)(struct __USART_HandleTypeDef *husart);         /*!< USART Msp DeInit callback              */
+#endif  /* USE_HAL_USART_REGISTER_CALLBACKS */
+
+} USART_HandleTypeDef;
+
+#if (USE_HAL_USART_REGISTER_CALLBACKS == 1)
+/**
+  * @brief  HAL USART Callback ID enumeration definition
+  */
+typedef enum
+{
+  HAL_USART_TX_HALFCOMPLETE_CB_ID         = 0x00U,    /*!< USART Tx Half Complete Callback ID        */
+  HAL_USART_TX_COMPLETE_CB_ID             = 0x01U,    /*!< USART Tx Complete Callback ID             */
+  HAL_USART_RX_HALFCOMPLETE_CB_ID         = 0x02U,    /*!< USART Rx Half Complete Callback ID        */
+  HAL_USART_RX_COMPLETE_CB_ID             = 0x03U,    /*!< USART Rx Complete Callback ID             */
+  HAL_USART_TX_RX_COMPLETE_CB_ID          = 0x04U,    /*!< USART Tx Rx Complete Callback ID          */
+  HAL_USART_ERROR_CB_ID                   = 0x05U,    /*!< USART Error Callback ID                   */
+  HAL_USART_ABORT_COMPLETE_CB_ID          = 0x06U,    /*!< USART Abort Complete Callback ID          */
+
+  HAL_USART_MSPINIT_CB_ID                 = 0x07U,    /*!< USART MspInit callback ID                 */
+  HAL_USART_MSPDEINIT_CB_ID               = 0x08U     /*!< USART MspDeInit callback ID               */
+
+} HAL_USART_CallbackIDTypeDef;
+
+/**
+  * @brief  HAL USART Callback pointer definition
+  */
+typedef  void (*pUSART_CallbackTypeDef)(USART_HandleTypeDef *husart);  /*!< pointer to an USART callback function */
+
+#endif /* USE_HAL_USART_REGISTER_CALLBACKS */
+
+/**
+  * @}
+  */
+
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup USART_Exported_Constants USART Exported Constants
+  * @{
+  */
+
+/** @defgroup USART_Error_Code USART Error Code
+  * @brief    USART Error Code
+  * @{
+  */
+#define HAL_USART_ERROR_NONE             0x00000000U   /*!< No error                */
+#define HAL_USART_ERROR_PE               0x00000001U   /*!< Parity error            */
+#define HAL_USART_ERROR_NE               0x00000002U   /*!< Noise error             */
+#define HAL_USART_ERROR_FE               0x00000004U   /*!< Frame error             */
+#define HAL_USART_ERROR_ORE              0x00000008U   /*!< Overrun error           */
+#define HAL_USART_ERROR_DMA              0x00000010U   /*!< DMA transfer error      */
+#if (USE_HAL_USART_REGISTER_CALLBACKS == 1)
+#define HAL_USART_ERROR_INVALID_CALLBACK 0x00000020U    /*!< Invalid Callback error */
+#endif /* USE_HAL_USART_REGISTER_CALLBACKS */
+/**
+  * @}
+  */
+
+/** @defgroup USART_Word_Length USART Word Length
+  * @{
+  */
+#define USART_WORDLENGTH_8B          0x00000000U
+#define USART_WORDLENGTH_9B          ((uint32_t)USART_CR1_M)
+/**
+  * @}
+  */
+
+/** @defgroup USART_Stop_Bits USART Number of Stop Bits
+  * @{
+  */
+#define USART_STOPBITS_1             0x00000000U
+#define USART_STOPBITS_0_5           ((uint32_t)USART_CR2_STOP_0)
+#define USART_STOPBITS_2             ((uint32_t)USART_CR2_STOP_1)
+#define USART_STOPBITS_1_5           ((uint32_t)(USART_CR2_STOP_0 | USART_CR2_STOP_1))
+/**
+  * @}
+  */
+
+/** @defgroup USART_Parity USART Parity
+  * @{
+  */
+#define USART_PARITY_NONE            0x00000000U
+#define USART_PARITY_EVEN            ((uint32_t)USART_CR1_PCE)
+#define USART_PARITY_ODD             ((uint32_t)(USART_CR1_PCE | USART_CR1_PS))
+/**
+  * @}
+  */
+
+/** @defgroup USART_Mode USART Mode
+  * @{
+  */
+#define USART_MODE_RX                ((uint32_t)USART_CR1_RE)
+#define USART_MODE_TX                ((uint32_t)USART_CR1_TE)
+#define USART_MODE_TX_RX             ((uint32_t)(USART_CR1_TE | USART_CR1_RE))
+/**
+  * @}
+  */
+
+/** @defgroup USART_Clock USART Clock
+  * @{
+  */
+#define USART_CLOCK_DISABLE          0x00000000U
+#define USART_CLOCK_ENABLE           ((uint32_t)USART_CR2_CLKEN)
+/**
+  * @}
+  */
+
+/** @defgroup USART_Clock_Polarity USART Clock Polarity
+  * @{
+  */
+#define USART_POLARITY_LOW           0x00000000U
+#define USART_POLARITY_HIGH          ((uint32_t)USART_CR2_CPOL)
+/**
+  * @}
+  */
+
+/** @defgroup USART_Clock_Phase USART Clock Phase
+  * @{
+  */
+#define USART_PHASE_1EDGE            0x00000000U
+#define USART_PHASE_2EDGE            ((uint32_t)USART_CR2_CPHA)
+/**
+  * @}
+  */
+
+/** @defgroup USART_Last_Bit USART Last Bit
+  * @{
+  */
+#define USART_LASTBIT_DISABLE        0x00000000U
+#define USART_LASTBIT_ENABLE         ((uint32_t)USART_CR2_LBCL)
+/**
+  * @}
+  */
+
+/** @defgroup USART_NACK_State USART NACK State
+  * @{
+  */
+#define USART_NACK_ENABLE            ((uint32_t)USART_CR3_NACK)
+#define USART_NACK_DISABLE           0x00000000U
+/**
+  * @}
+  */
+
+/** @defgroup USART_Flags USART Flags
+  *        Elements values convention: 0xXXXX
+  *           - 0xXXXX  : Flag mask in the SR register
+  * @{
+  */
+#define USART_FLAG_TXE               ((uint32_t)USART_SR_TXE)
+#define USART_FLAG_TC                ((uint32_t)USART_SR_TC)
+#define USART_FLAG_RXNE              ((uint32_t)USART_SR_RXNE)
+#define USART_FLAG_IDLE              ((uint32_t)USART_SR_IDLE)
+#define USART_FLAG_ORE               ((uint32_t)USART_SR_ORE)
+#define USART_FLAG_NE                ((uint32_t)USART_SR_NE)
+#define USART_FLAG_FE                ((uint32_t)USART_SR_FE)
+#define USART_FLAG_PE                ((uint32_t)USART_SR_PE)
+/**
+  * @}
+  */
+
+/** @defgroup USART_Interrupt_definition USART Interrupts Definition
+  *        Elements values convention: 0xY000XXXX
+  *           - XXXX  : Interrupt mask in the XX register
+  *           - Y  : Interrupt source register (2bits)
+  *                 - 01: CR1 register
+  *                 - 10: CR2 register
+  *                 - 11: CR3 register
+  * @{
+  */
+#define USART_IT_PE                  ((uint32_t)(USART_CR1_REG_INDEX << 28U | USART_CR1_PEIE))
+#define USART_IT_TXE                 ((uint32_t)(USART_CR1_REG_INDEX << 28U | USART_CR1_TXEIE))
+#define USART_IT_TC                  ((uint32_t)(USART_CR1_REG_INDEX << 28U | USART_CR1_TCIE))
+#define USART_IT_RXNE                ((uint32_t)(USART_CR1_REG_INDEX << 28U | USART_CR1_RXNEIE))
+#define USART_IT_IDLE                ((uint32_t)(USART_CR1_REG_INDEX << 28U | USART_CR1_IDLEIE))
+#define USART_IT_ERR                 ((uint32_t)(USART_CR3_REG_INDEX << 28U | USART_CR3_EIE))
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Exported macro ------------------------------------------------------------*/
+/** @defgroup USART_Exported_Macros USART Exported Macros
+  * @{
+  */
+
+/** @brief Reset USART handle state
+  * @param  __HANDLE__ specifies the USART Handle.
+  *         USART Handle selects the USARTx peripheral (USART availability and x value depending on device).
+  * @retval None
+  */
+#if (USE_HAL_USART_REGISTER_CALLBACKS == 1)
+#define __HAL_USART_RESET_HANDLE_STATE(__HANDLE__)  do{                                            \
+                                                      (__HANDLE__)->State = HAL_USART_STATE_RESET; \
+                                                      (__HANDLE__)->MspInitCallback = NULL;        \
+                                                      (__HANDLE__)->MspDeInitCallback = NULL;      \
+                                                    } while(0U)
+#else
+#define __HAL_USART_RESET_HANDLE_STATE(__HANDLE__)  ((__HANDLE__)->State = HAL_USART_STATE_RESET)
+#endif /* USE_HAL_USART_REGISTER_CALLBACKS */
+
+/** @brief  Check whether the specified USART flag is set or not.
+  * @param  __HANDLE__ specifies the USART Handle.
+  *         USART Handle selects the USARTx peripheral (USART availability and x value depending on device).
+  * @param  __FLAG__ specifies the flag to check.
+  *        This parameter can be one of the following values:
+  *            @arg USART_FLAG_TXE:  Transmit data register empty flag
+  *            @arg USART_FLAG_TC:   Transmission Complete flag
+  *            @arg USART_FLAG_RXNE: Receive data register not empty flag
+  *            @arg USART_FLAG_IDLE: Idle Line detection flag
+  *            @arg USART_FLAG_ORE:  Overrun Error flag
+  *            @arg USART_FLAG_NE:   Noise Error flag
+  *            @arg USART_FLAG_FE:   Framing Error flag
+  *            @arg USART_FLAG_PE:   Parity Error flag
+  * @retval The new state of __FLAG__ (TRUE or FALSE).
+  */
+#define __HAL_USART_GET_FLAG(__HANDLE__, __FLAG__) (((__HANDLE__)->Instance->SR & (__FLAG__)) == (__FLAG__))
+
+/** @brief  Clear the specified USART pending flags.
+  * @param  __HANDLE__ specifies the USART Handle.
+  *         USART Handle selects the USARTx peripheral (USART availability and x value depending on device).
+  * @param  __FLAG__ specifies the flag to check.
+  *          This parameter can be any combination of the following values:
+  *            @arg USART_FLAG_TC:   Transmission Complete flag.
+  *            @arg USART_FLAG_RXNE: Receive data register not empty flag.
+  *
+  * @note   PE (Parity error), FE (Framing error), NE (Noise error), ORE (Overrun
+  *          error) and IDLE (Idle line detected) flags are cleared by software
+  *          sequence: a read operation to USART_SR register followed by a read
+  *          operation to USART_DR register.
+  * @note   RXNE flag can be also cleared by a read to the USART_DR register.
+  * @note   TC flag can be also cleared by software sequence: a read operation to
+  *          USART_SR register followed by a write operation to USART_DR register.
+  * @note   TXE flag is cleared only by a write to the USART_DR register.
+  *
+  * @retval None
+  */
+#define __HAL_USART_CLEAR_FLAG(__HANDLE__, __FLAG__) ((__HANDLE__)->Instance->SR = ~(__FLAG__))
+
+/** @brief  Clear the USART PE pending flag.
+  * @param  __HANDLE__ specifies the USART Handle.
+  *         USART Handle selects the USARTx peripheral (USART availability and x value depending on device).
+  * @retval None
+  */
+#define __HAL_USART_CLEAR_PEFLAG(__HANDLE__)    \
+  do{                                           \
+    __IO uint32_t tmpreg = 0x00U;               \
+    tmpreg = (__HANDLE__)->Instance->SR;        \
+    tmpreg = (__HANDLE__)->Instance->DR;        \
+    UNUSED(tmpreg);                             \
+  } while(0U)
+
+/** @brief  Clear the USART FE pending flag.
+  * @param  __HANDLE__ specifies the USART Handle.
+  *         USART Handle selects the USARTx peripheral (USART availability and x value depending on device).
+  * @retval None
+  */
+#define __HAL_USART_CLEAR_FEFLAG(__HANDLE__) __HAL_USART_CLEAR_PEFLAG(__HANDLE__)
+
+/** @brief  Clear the USART NE pending flag.
+  * @param  __HANDLE__ specifies the USART Handle.
+  *         USART Handle selects the USARTx peripheral (USART availability and x value depending on device).
+  * @retval None
+  */
+#define __HAL_USART_CLEAR_NEFLAG(__HANDLE__) __HAL_USART_CLEAR_PEFLAG(__HANDLE__)
+
+/** @brief  Clear the USART ORE pending flag.
+  * @param  __HANDLE__ specifies the USART Handle.
+  *         USART Handle selects the USARTx peripheral (USART availability and x value depending on device).
+  * @retval None
+  */
+#define __HAL_USART_CLEAR_OREFLAG(__HANDLE__) __HAL_USART_CLEAR_PEFLAG(__HANDLE__)
+
+/** @brief  Clear the USART IDLE pending flag.
+  * @param  __HANDLE__ specifies the USART Handle.
+  *         USART Handle selects the USARTx peripheral (USART availability and x value depending on device).
+  * @retval None
+  */
+#define __HAL_USART_CLEAR_IDLEFLAG(__HANDLE__) __HAL_USART_CLEAR_PEFLAG(__HANDLE__)
+
+/** @brief  Enables or disables the specified USART interrupts.
+  * @param  __HANDLE__ specifies the USART Handle.
+  *         USART Handle selects the USARTx peripheral (USART availability and x value depending on device).
+  * @param  __INTERRUPT__ specifies the USART interrupt source to check.
+  *          This parameter can be one of the following values:
+  *            @arg USART_IT_TXE:  Transmit Data Register empty interrupt
+  *            @arg USART_IT_TC:   Transmission complete interrupt
+  *            @arg USART_IT_RXNE: Receive Data register not empty interrupt
+  *            @arg USART_IT_IDLE: Idle line detection interrupt
+  *            @arg USART_IT_PE:   Parity Error interrupt
+  *            @arg USART_IT_ERR:  Error interrupt(Frame error, noise error, overrun error)
+  * @retval None
+  */
+#define __HAL_USART_ENABLE_IT(__HANDLE__, __INTERRUPT__)   ((((__INTERRUPT__) >> 28U) == USART_CR1_REG_INDEX)? ((__HANDLE__)->Instance->CR1 |= ((__INTERRUPT__) & USART_IT_MASK)): \
+                                                            (((__INTERRUPT__) >> 28U) == USART_CR2_REG_INDEX)? ((__HANDLE__)->Instance->CR2 |= ((__INTERRUPT__) & USART_IT_MASK)): \
+                                                             ((__HANDLE__)->Instance->CR3 |= ((__INTERRUPT__) & USART_IT_MASK)))
+#define __HAL_USART_DISABLE_IT(__HANDLE__, __INTERRUPT__)  ((((__INTERRUPT__) >> 28U) == USART_CR1_REG_INDEX)? ((__HANDLE__)->Instance->CR1 &= ~((__INTERRUPT__) & USART_IT_MASK)): \
+                                                            (((__INTERRUPT__) >> 28U) == USART_CR2_REG_INDEX)? ((__HANDLE__)->Instance->CR2 &= ~((__INTERRUPT__) & USART_IT_MASK)): \
+                                                             ((__HANDLE__)->Instance->CR3 &= ~ ((__INTERRUPT__) & USART_IT_MASK)))
+
+/** @brief  Checks whether the specified USART interrupt has occurred or not.
+  * @param  __HANDLE__ specifies the USART Handle.
+  *         USART Handle selects the USARTx peripheral (USART availability and x value depending on device).
+  * @param  __IT__ specifies the USART interrupt source to check.
+  *          This parameter can be one of the following values:
+  *            @arg USART_IT_TXE: Transmit Data Register empty interrupt
+  *            @arg USART_IT_TC:  Transmission complete interrupt
+  *            @arg USART_IT_RXNE: Receive Data register not empty interrupt
+  *            @arg USART_IT_IDLE: Idle line detection interrupt
+  *            @arg USART_IT_ERR: Error interrupt
+  *            @arg USART_IT_PE: Parity Error interrupt
+  * @retval The new state of __IT__ (TRUE or FALSE).
+  */
+#define __HAL_USART_GET_IT_SOURCE(__HANDLE__, __IT__) (((((__IT__) >> 28U) == USART_CR1_REG_INDEX)? (__HANDLE__)->Instance->CR1:(((((uint32_t)(__IT__)) >> 28U) == USART_CR2_REG_INDEX)? \
+                                                      (__HANDLE__)->Instance->CR2 : (__HANDLE__)->Instance->CR3)) & (((uint32_t)(__IT__)) & USART_IT_MASK))
+
+/** @brief  Macro to enable the USART's one bit sample method
+  * @param  __HANDLE__ specifies the USART Handle.
+  * @retval None
+  */
+#define __HAL_USART_ONE_BIT_SAMPLE_ENABLE(__HANDLE__) ((__HANDLE__)->Instance->CR3 |= USART_CR3_ONEBIT)
+
+/** @brief  Macro to disable the USART's one bit sample method
+  * @param  __HANDLE__ specifies the USART Handle.
+  * @retval None
+  */
+#define __HAL_USART_ONE_BIT_SAMPLE_DISABLE(__HANDLE__) ((__HANDLE__)->Instance->CR3 &= (uint16_t)~((uint16_t)USART_CR3_ONEBIT))
+
+/** @brief  Enable USART
+  * @param  __HANDLE__ specifies the USART Handle.
+  *         USART Handle selects the USARTx peripheral (USART availability and x value depending on device).
+  * @retval None
+  */
+#define __HAL_USART_ENABLE(__HANDLE__)               ((__HANDLE__)->Instance->CR1 |= USART_CR1_UE)
+
+/** @brief  Disable USART
+  * @param  __HANDLE__ specifies the USART Handle.
+  *         USART Handle selects the USARTx peripheral (USART availability and x value depending on device).
+  * @retval None
+  */
+#define __HAL_USART_DISABLE(__HANDLE__)              ((__HANDLE__)->Instance->CR1 &= ~USART_CR1_UE)
+
+/**
+  * @}
+  */
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup USART_Exported_Functions
+  * @{
+  */
+
+/** @addtogroup USART_Exported_Functions_Group1
+  * @{
+  */
+/* Initialization/de-initialization functions  **********************************/
+HAL_StatusTypeDef HAL_USART_Init(USART_HandleTypeDef *husart);
+HAL_StatusTypeDef HAL_USART_DeInit(USART_HandleTypeDef *husart);
+void HAL_USART_MspInit(USART_HandleTypeDef *husart);
+void HAL_USART_MspDeInit(USART_HandleTypeDef *husart);
+
+/* Callbacks Register/UnRegister functions  ***********************************/
+#if (USE_HAL_USART_REGISTER_CALLBACKS == 1)
+HAL_StatusTypeDef HAL_USART_RegisterCallback(USART_HandleTypeDef *husart, HAL_USART_CallbackIDTypeDef CallbackID, pUSART_CallbackTypeDef pCallback);
+HAL_StatusTypeDef HAL_USART_UnRegisterCallback(USART_HandleTypeDef *husart, HAL_USART_CallbackIDTypeDef CallbackID);
+#endif /* USE_HAL_USART_REGISTER_CALLBACKS */
+
+/**
+  * @}
+  */
+
+/** @addtogroup USART_Exported_Functions_Group2
+  * @{
+  */
+/* IO operation functions *******************************************************/
+HAL_StatusTypeDef HAL_USART_Transmit(USART_HandleTypeDef *husart, uint8_t *pTxData, uint16_t Size, uint32_t Timeout);
+HAL_StatusTypeDef HAL_USART_Receive(USART_HandleTypeDef *husart, uint8_t *pRxData, uint16_t Size, uint32_t Timeout);
+HAL_StatusTypeDef HAL_USART_TransmitReceive(USART_HandleTypeDef *husart, uint8_t *pTxData, uint8_t *pRxData, uint16_t Size, uint32_t Timeout);
+HAL_StatusTypeDef HAL_USART_Transmit_IT(USART_HandleTypeDef *husart, uint8_t *pTxData, uint16_t Size);
+HAL_StatusTypeDef HAL_USART_Receive_IT(USART_HandleTypeDef *husart, uint8_t *pRxData, uint16_t Size);
+HAL_StatusTypeDef HAL_USART_TransmitReceive_IT(USART_HandleTypeDef *husart, uint8_t *pTxData, uint8_t *pRxData,  uint16_t Size);
+HAL_StatusTypeDef HAL_USART_Transmit_DMA(USART_HandleTypeDef *husart, uint8_t *pTxData, uint16_t Size);
+HAL_StatusTypeDef HAL_USART_Receive_DMA(USART_HandleTypeDef *husart, uint8_t *pRxData, uint16_t Size);
+HAL_StatusTypeDef HAL_USART_TransmitReceive_DMA(USART_HandleTypeDef *husart, uint8_t *pTxData, uint8_t *pRxData, uint16_t Size);
+HAL_StatusTypeDef HAL_USART_DMAPause(USART_HandleTypeDef *husart);
+HAL_StatusTypeDef HAL_USART_DMAResume(USART_HandleTypeDef *husart);
+HAL_StatusTypeDef HAL_USART_DMAStop(USART_HandleTypeDef *husart);
+/* Transfer Abort functions */
+HAL_StatusTypeDef HAL_USART_Abort(USART_HandleTypeDef *husart);
+HAL_StatusTypeDef HAL_USART_Abort_IT(USART_HandleTypeDef *husart);
+
+void HAL_USART_IRQHandler(USART_HandleTypeDef *husart);
+void HAL_USART_TxCpltCallback(USART_HandleTypeDef *husart);
+void HAL_USART_TxHalfCpltCallback(USART_HandleTypeDef *husart);
+void HAL_USART_RxCpltCallback(USART_HandleTypeDef *husart);
+void HAL_USART_RxHalfCpltCallback(USART_HandleTypeDef *husart);
+void HAL_USART_TxRxCpltCallback(USART_HandleTypeDef *husart);
+void HAL_USART_ErrorCallback(USART_HandleTypeDef *husart);
+void HAL_USART_AbortCpltCallback(USART_HandleTypeDef *husart);
+/**
+  * @}
+  */
+
+/** @addtogroup USART_Exported_Functions_Group3
+  * @{
+  */
+/* Peripheral State functions  ************************************************/
+HAL_USART_StateTypeDef HAL_USART_GetState(USART_HandleTypeDef *husart);
+uint32_t               HAL_USART_GetError(USART_HandleTypeDef *husart);
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+/* Private types -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private constants ---------------------------------------------------------*/
+/** @defgroup USART_Private_Constants USART Private Constants
+  * @{
+  */
+/** @brief USART interruptions flag mask
+  *
+  */
+#define USART_IT_MASK  ((uint32_t) USART_CR1_PEIE | USART_CR1_TXEIE | USART_CR1_TCIE | USART_CR1_RXNEIE | \
+                                   USART_CR1_IDLEIE | USART_CR2_LBDIE | USART_CR3_CTSIE | USART_CR3_EIE )
+
+#define USART_CR1_REG_INDEX          1U
+#define USART_CR2_REG_INDEX          2U
+#define USART_CR3_REG_INDEX          3U
+/**
+  * @}
+  */
+
+/* Private macros ------------------------------------------------------------*/
+/** @defgroup USART_Private_Macros USART Private Macros
+  * @{
+  */
+#define IS_USART_NACK_STATE(NACK)    (((NACK) == USART_NACK_ENABLE) || \
+                                      ((NACK) == USART_NACK_DISABLE))
+
+#define IS_USART_LASTBIT(LASTBIT)    (((LASTBIT) == USART_LASTBIT_DISABLE) || \
+                                      ((LASTBIT) == USART_LASTBIT_ENABLE))
+
+#define IS_USART_PHASE(CPHA)         (((CPHA) == USART_PHASE_1EDGE) || \
+                                      ((CPHA) == USART_PHASE_2EDGE))
+
+#define IS_USART_POLARITY(CPOL)      (((CPOL) == USART_POLARITY_LOW) || \
+                                      ((CPOL) == USART_POLARITY_HIGH))
+
+#define IS_USART_CLOCK(CLOCK)        (((CLOCK) == USART_CLOCK_DISABLE) || \
+                                      ((CLOCK) == USART_CLOCK_ENABLE))
+
+#define IS_USART_WORD_LENGTH(LENGTH) (((LENGTH) == USART_WORDLENGTH_8B) || \
+                                      ((LENGTH) == USART_WORDLENGTH_9B))
+
+#define IS_USART_STOPBITS(STOPBITS)  (((STOPBITS) == USART_STOPBITS_1) || \
+                                      ((STOPBITS) == USART_STOPBITS_0_5) || \
+                                      ((STOPBITS) == USART_STOPBITS_1_5) || \
+                                      ((STOPBITS) == USART_STOPBITS_2))
+
+#define IS_USART_PARITY(PARITY)      (((PARITY) == USART_PARITY_NONE) || \
+                                      ((PARITY) == USART_PARITY_EVEN) || \
+                                      ((PARITY) == USART_PARITY_ODD))
+
+#define IS_USART_MODE(MODE)          ((((MODE) & (~((uint32_t)USART_MODE_TX_RX))) == 0x00U) && ((MODE) != 0x00U))
+
+#define IS_USART_BAUDRATE(BAUDRATE)  ((BAUDRATE) <= 4500000U)
+
+#define USART_DIV(_PCLK_, _BAUD_)      (((_PCLK_)*25U)/(4U*(_BAUD_)))
+
+#define USART_DIVMANT(_PCLK_, _BAUD_)  (USART_DIV((_PCLK_), (_BAUD_))/100U)
+
+#define USART_DIVFRAQ(_PCLK_, _BAUD_)  ((((USART_DIV((_PCLK_), (_BAUD_)) - (USART_DIVMANT((_PCLK_), (_BAUD_)) * 100U)) * 16U) + 50U) / 100U)
+
+  /* UART BRR = mantissa + overflow + fraction
+              = (UART DIVMANT << 4) + ((UART DIVFRAQ & 0xF0) << 1) + (UART DIVFRAQ & 0x0FU) */
+            
+#define USART_BRR(_PCLK_, _BAUD_)      (((USART_DIVMANT((_PCLK_), (_BAUD_)) << 4U) + \
+                                        ((USART_DIVFRAQ((_PCLK_), (_BAUD_)) & 0xF0U) << 1U)) + \
+                                         (USART_DIVFRAQ((_PCLK_), (_BAUD_)) & 0x0FU))
+/**
+  * @}
+  */
+
+/* Private functions ---------------------------------------------------------*/
+/** @defgroup USART_Private_Functions USART Private Functions
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F1xx_HAL_USART_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_hal_wwdg.h

@@ -0,0 +1,301 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_hal_wwdg.h
+  * @author  MCD Application Team
+  * @brief   Header file of WWDG HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef STM32F1xx_HAL_WWDG_H
+#define STM32F1xx_HAL_WWDG_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_hal_def.h"
+
+/** @addtogroup STM32F1xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup WWDG
+  * @{
+  */
+
+/* Exported types ------------------------------------------------------------*/
+
+/** @defgroup WWDG_Exported_Types WWDG Exported Types
+  * @{
+  */
+
+/**
+  * @brief  WWDG Init structure definition
+  */
+typedef struct
+{
+  uint32_t Prescaler;     /*!< Specifies the prescaler value of the WWDG.
+                               This parameter can be a value of @ref WWDG_Prescaler */
+
+  uint32_t Window;        /*!< Specifies the WWDG window value to be compared to the downcounter.
+                               This parameter must be a number Min_Data = 0x40 and Max_Data = 0x7F */
+
+  uint32_t Counter;       /*!< Specifies the WWDG free-running downcounter  value.
+                               This parameter must be a number between Min_Data = 0x40 and Max_Data = 0x7F */
+
+  uint32_t EWIMode ;      /*!< Specifies if WWDG Early Wakeup Interrupt is enable or not.
+                               This parameter can be a value of @ref WWDG_EWI_Mode */
+
+} WWDG_InitTypeDef;
+
+/**
+  * @brief  WWDG handle Structure definition
+  */
+#if (USE_HAL_WWDG_REGISTER_CALLBACKS == 1)
+typedef struct __WWDG_HandleTypeDef
+#else
+typedef struct
+#endif /* USE_HAL_WWDG_REGISTER_CALLBACKS */
+{
+  WWDG_TypeDef      *Instance;  /*!< Register base address */
+
+  WWDG_InitTypeDef  Init;       /*!< WWDG required parameters */
+
+#if (USE_HAL_WWDG_REGISTER_CALLBACKS == 1)
+  void (* EwiCallback)(struct __WWDG_HandleTypeDef *hwwdg);                  /*!< WWDG Early WakeUp Interrupt callback */
+
+  void (* MspInitCallback)(struct __WWDG_HandleTypeDef *hwwdg);              /*!< WWDG Msp Init callback */
+#endif /* USE_HAL_WWDG_REGISTER_CALLBACKS */
+} WWDG_HandleTypeDef;
+
+#if (USE_HAL_WWDG_REGISTER_CALLBACKS == 1)
+/**
+  * @brief  HAL WWDG common Callback ID enumeration definition
+  */
+typedef enum
+{
+  HAL_WWDG_EWI_CB_ID          = 0x00U,    /*!< WWDG EWI callback ID */
+  HAL_WWDG_MSPINIT_CB_ID      = 0x01U,    /*!< WWDG MspInit callback ID */
+} HAL_WWDG_CallbackIDTypeDef;
+
+/**
+  * @brief  HAL WWDG Callback pointer definition
+  */
+typedef void (*pWWDG_CallbackTypeDef)(WWDG_HandleTypeDef *hppp);  /*!< pointer to a WWDG common callback functions */
+
+#endif /* USE_HAL_WWDG_REGISTER_CALLBACKS */
+/**
+  * @}
+  */
+
+/* Exported constants --------------------------------------------------------*/
+
+/** @defgroup WWDG_Exported_Constants WWDG Exported Constants
+  * @{
+  */
+
+/** @defgroup WWDG_Interrupt_definition WWDG Interrupt definition
+  * @{
+  */
+#define WWDG_IT_EWI                         WWDG_CFR_EWI  /*!< Early wakeup interrupt */
+/**
+  * @}
+  */
+
+/** @defgroup WWDG_Flag_definition WWDG Flag definition
+  * @brief WWDG Flag definition
+  * @{
+  */
+#define WWDG_FLAG_EWIF                      WWDG_SR_EWIF  /*!< Early wakeup interrupt flag */
+/**
+  * @}
+  */
+
+/** @defgroup WWDG_Prescaler WWDG Prescaler
+  * @{
+  */
+#define WWDG_PRESCALER_1                    0x00000000u                              /*!< WWDG counter clock = (PCLK1/4096)/1 */
+#define WWDG_PRESCALER_2                    WWDG_CFR_WDGTB_0                         /*!< WWDG counter clock = (PCLK1/4096)/2 */
+#define WWDG_PRESCALER_4                    WWDG_CFR_WDGTB_1                         /*!< WWDG counter clock = (PCLK1/4096)/4 */
+#define WWDG_PRESCALER_8                    (WWDG_CFR_WDGTB_1 | WWDG_CFR_WDGTB_0)    /*!< WWDG counter clock = (PCLK1/4096)/8 */
+/**
+  * @}
+  */
+
+/** @defgroup WWDG_EWI_Mode WWDG Early Wakeup Interrupt Mode
+  * @{
+  */
+#define WWDG_EWI_DISABLE                    0x00000000u       /*!< EWI Disable */
+#define WWDG_EWI_ENABLE                     WWDG_CFR_EWI      /*!< EWI Enable */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Private macros ------------------------------------------------------------*/
+
+/** @defgroup WWDG_Private_Macros WWDG Private Macros
+  * @{
+  */
+#define IS_WWDG_PRESCALER(__PRESCALER__)    (((__PRESCALER__) == WWDG_PRESCALER_1)  || \
+                                             ((__PRESCALER__) == WWDG_PRESCALER_2)  || \
+                                             ((__PRESCALER__) == WWDG_PRESCALER_4)  || \
+                                             ((__PRESCALER__) == WWDG_PRESCALER_8))
+
+#define IS_WWDG_WINDOW(__WINDOW__)          (((__WINDOW__) >= WWDG_CFR_W_6) && ((__WINDOW__) <= WWDG_CFR_W))
+
+#define IS_WWDG_COUNTER(__COUNTER__)        (((__COUNTER__) >= WWDG_CR_T_6) && ((__COUNTER__) <= WWDG_CR_T))
+
+#define IS_WWDG_EWI_MODE(__MODE__)          (((__MODE__) == WWDG_EWI_ENABLE) || \
+                                             ((__MODE__) == WWDG_EWI_DISABLE))
+/**
+  * @}
+  */
+
+
+/* Exported macros ------------------------------------------------------------*/
+
+/** @defgroup WWDG_Exported_Macros WWDG Exported Macros
+  * @{
+  */
+
+/**
+  * @brief  Enable the WWDG peripheral.
+  * @param  __HANDLE__  WWDG handle
+  * @retval None
+  */
+#define __HAL_WWDG_ENABLE(__HANDLE__)                         SET_BIT((__HANDLE__)->Instance->CR, WWDG_CR_WDGA)
+
+/**
+  * @brief  Enable the WWDG early wakeup interrupt.
+  * @param  __HANDLE__: WWDG handle
+  * @param  __INTERRUPT__  specifies the interrupt to enable.
+  *         This parameter can be one of the following values:
+  *            @arg WWDG_IT_EWI: Early wakeup interrupt
+  * @note   Once enabled this interrupt cannot be disabled except by a system reset.
+  * @retval None
+  */
+#define __HAL_WWDG_ENABLE_IT(__HANDLE__, __INTERRUPT__)       SET_BIT((__HANDLE__)->Instance->CFR, (__INTERRUPT__))
+
+/**
+  * @brief  Check whether the selected WWDG interrupt has occurred or not.
+  * @param  __HANDLE__  WWDG handle
+  * @param  __INTERRUPT__  specifies the it to check.
+  *        This parameter can be one of the following values:
+  *            @arg WWDG_FLAG_EWIF: Early wakeup interrupt IT
+  * @retval The new state of WWDG_FLAG (SET or RESET).
+  */
+#define __HAL_WWDG_GET_IT(__HANDLE__, __INTERRUPT__)        __HAL_WWDG_GET_FLAG((__HANDLE__),(__INTERRUPT__))
+
+/** @brief  Clear the WWDG interrupt pending bits.
+  *         bits to clear the selected interrupt pending bits.
+  * @param  __HANDLE__  WWDG handle
+  * @param  __INTERRUPT__  specifies the interrupt pending bit to clear.
+  *         This parameter can be one of the following values:
+  *            @arg WWDG_FLAG_EWIF: Early wakeup interrupt flag
+  */
+#define __HAL_WWDG_CLEAR_IT(__HANDLE__, __INTERRUPT__)      __HAL_WWDG_CLEAR_FLAG((__HANDLE__), (__INTERRUPT__))
+
+/**
+  * @brief  Check whether the specified WWDG flag is set or not.
+  * @param  __HANDLE__  WWDG handle
+  * @param  __FLAG__  specifies the flag to check.
+  *         This parameter can be one of the following values:
+  *            @arg WWDG_FLAG_EWIF: Early wakeup interrupt flag
+  * @retval The new state of WWDG_FLAG (SET or RESET).
+  */
+#define __HAL_WWDG_GET_FLAG(__HANDLE__, __FLAG__)           (((__HANDLE__)->Instance->SR & (__FLAG__)) == (__FLAG__))
+
+/**
+  * @brief  Clear the WWDG's pending flags.
+  * @param  __HANDLE__  WWDG handle
+  * @param  __FLAG__  specifies the flag to clear.
+  *         This parameter can be one of the following values:
+  *            @arg WWDG_FLAG_EWIF: Early wakeup interrupt flag
+  * @retval None
+  */
+#define __HAL_WWDG_CLEAR_FLAG(__HANDLE__, __FLAG__)         ((__HANDLE__)->Instance->SR = ~(__FLAG__))
+
+/** @brief  Check whether the specified WWDG interrupt source is enabled or not.
+  * @param  __HANDLE__  WWDG Handle.
+  * @param  __INTERRUPT__  specifies the WWDG interrupt source to check.
+  *         This parameter can be one of the following values:
+  *            @arg WWDG_IT_EWI: Early Wakeup Interrupt
+  * @retval state of __INTERRUPT__ (TRUE or FALSE).
+  */
+#define __HAL_WWDG_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__) (((__HANDLE__)->Instance->CFR\
+                                                              & (__INTERRUPT__)) == (__INTERRUPT__))
+
+/**
+  * @}
+  */
+
+/* Exported functions --------------------------------------------------------*/
+
+/** @addtogroup WWDG_Exported_Functions
+  * @{
+  */
+
+/** @addtogroup WWDG_Exported_Functions_Group1
+  * @{
+  */
+/* Initialization/de-initialization functions  **********************************/
+HAL_StatusTypeDef     HAL_WWDG_Init(WWDG_HandleTypeDef *hwwdg);
+void                  HAL_WWDG_MspInit(WWDG_HandleTypeDef *hwwdg);
+/* Callbacks Register/UnRegister functions  ***********************************/
+#if (USE_HAL_WWDG_REGISTER_CALLBACKS == 1)
+HAL_StatusTypeDef     HAL_WWDG_RegisterCallback(WWDG_HandleTypeDef *hwwdg, HAL_WWDG_CallbackIDTypeDef CallbackID,
+                                                pWWDG_CallbackTypeDef pCallback);
+HAL_StatusTypeDef     HAL_WWDG_UnRegisterCallback(WWDG_HandleTypeDef *hwwdg, HAL_WWDG_CallbackIDTypeDef CallbackID);
+#endif /* USE_HAL_WWDG_REGISTER_CALLBACKS */
+
+/**
+  * @}
+  */
+
+/** @addtogroup WWDG_Exported_Functions_Group2
+  * @{
+  */
+/* I/O operation functions ******************************************************/
+HAL_StatusTypeDef     HAL_WWDG_Refresh(WWDG_HandleTypeDef *hwwdg);
+void                  HAL_WWDG_IRQHandler(WWDG_HandleTypeDef *hwwdg);
+void                  HAL_WWDG_EarlyWakeupCallback(WWDG_HandleTypeDef *hwwdg);
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* STM32F1xx_HAL_WWDG_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_ll_cortex.h

@@ -0,0 +1,640 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_ll_cortex.h
+  * @author  MCD Application Team
+  * @brief   Header file of CORTEX LL module.
+  @verbatim
+  ==============================================================================
+                     ##### How to use this driver #####
+  ==============================================================================
+    [..]
+    The LL CORTEX driver contains a set of generic APIs that can be
+    used by user:
+      (+) SYSTICK configuration used by @ref LL_mDelay and @ref LL_Init1msTick
+          functions
+      (+) Low power mode configuration (SCB register of Cortex-MCU)
+      (+) MPU API to configure and enable regions
+          (MPU services provided only on some devices)
+      (+) API to access to MCU info (CPUID register)
+      (+) API to enable fault handler (SHCSR accesses)
+
+  @endverbatim
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F1xx_LL_CORTEX_H
+#define __STM32F1xx_LL_CORTEX_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx.h"
+
+/** @addtogroup STM32F1xx_LL_Driver
+  * @{
+  */
+
+/** @defgroup CORTEX_LL CORTEX
+  * @{
+  */
+
+/* Private types -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+
+/* Private constants ---------------------------------------------------------*/
+
+/* Private macros ------------------------------------------------------------*/
+
+/* Exported types ------------------------------------------------------------*/
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup CORTEX_LL_Exported_Constants CORTEX Exported Constants
+  * @{
+  */
+
+/** @defgroup CORTEX_LL_EC_CLKSOURCE_HCLK SYSTICK Clock Source
+  * @{
+  */
+#define LL_SYSTICK_CLKSOURCE_HCLK_DIV8     0x00000000U                 /*!< AHB clock divided by 8 selected as SysTick clock source.*/
+#define LL_SYSTICK_CLKSOURCE_HCLK          SysTick_CTRL_CLKSOURCE_Msk  /*!< AHB clock selected as SysTick clock source. */
+/**
+  * @}
+  */
+
+/** @defgroup CORTEX_LL_EC_FAULT Handler Fault type
+  * @{
+  */
+#define LL_HANDLER_FAULT_USG               SCB_SHCSR_USGFAULTENA_Msk              /*!< Usage fault */
+#define LL_HANDLER_FAULT_BUS               SCB_SHCSR_BUSFAULTENA_Msk              /*!< Bus fault */
+#define LL_HANDLER_FAULT_MEM               SCB_SHCSR_MEMFAULTENA_Msk              /*!< Memory management fault */
+/**
+  * @}
+  */
+
+#if __MPU_PRESENT
+
+/** @defgroup CORTEX_LL_EC_CTRL_HFNMI_PRIVDEF MPU Control
+  * @{
+  */
+#define LL_MPU_CTRL_HFNMI_PRIVDEF_NONE     0x00000000U                                       /*!< Disable NMI and privileged SW access */
+#define LL_MPU_CTRL_HARDFAULT_NMI          MPU_CTRL_HFNMIENA_Msk                             /*!< Enables the operation of MPU during hard fault, NMI, and FAULTMASK handlers */
+#define LL_MPU_CTRL_PRIVILEGED_DEFAULT     MPU_CTRL_PRIVDEFENA_Msk                           /*!< Enable privileged software access to default memory map */
+#define LL_MPU_CTRL_HFNMI_PRIVDEF          (MPU_CTRL_HFNMIENA_Msk | MPU_CTRL_PRIVDEFENA_Msk) /*!< Enable NMI and privileged SW access */
+/**
+  * @}
+  */
+
+/** @defgroup CORTEX_LL_EC_REGION MPU Region Number
+  * @{
+  */
+#define LL_MPU_REGION_NUMBER0              0x00U /*!< REGION Number 0 */
+#define LL_MPU_REGION_NUMBER1              0x01U /*!< REGION Number 1 */
+#define LL_MPU_REGION_NUMBER2              0x02U /*!< REGION Number 2 */
+#define LL_MPU_REGION_NUMBER3              0x03U /*!< REGION Number 3 */
+#define LL_MPU_REGION_NUMBER4              0x04U /*!< REGION Number 4 */
+#define LL_MPU_REGION_NUMBER5              0x05U /*!< REGION Number 5 */
+#define LL_MPU_REGION_NUMBER6              0x06U /*!< REGION Number 6 */
+#define LL_MPU_REGION_NUMBER7              0x07U /*!< REGION Number 7 */
+/**
+  * @}
+  */
+
+/** @defgroup CORTEX_LL_EC_REGION_SIZE MPU Region Size
+  * @{
+  */
+#define LL_MPU_REGION_SIZE_32B             (0x04U << MPU_RASR_SIZE_Pos) /*!< 32B Size of the MPU protection region */
+#define LL_MPU_REGION_SIZE_64B             (0x05U << MPU_RASR_SIZE_Pos) /*!< 64B Size of the MPU protection region */
+#define LL_MPU_REGION_SIZE_128B            (0x06U << MPU_RASR_SIZE_Pos) /*!< 128B Size of the MPU protection region */
+#define LL_MPU_REGION_SIZE_256B            (0x07U << MPU_RASR_SIZE_Pos) /*!< 256B Size of the MPU protection region */
+#define LL_MPU_REGION_SIZE_512B            (0x08U << MPU_RASR_SIZE_Pos) /*!< 512B Size of the MPU protection region */
+#define LL_MPU_REGION_SIZE_1KB             (0x09U << MPU_RASR_SIZE_Pos) /*!< 1KB Size of the MPU protection region */
+#define LL_MPU_REGION_SIZE_2KB             (0x0AU << MPU_RASR_SIZE_Pos) /*!< 2KB Size of the MPU protection region */
+#define LL_MPU_REGION_SIZE_4KB             (0x0BU << MPU_RASR_SIZE_Pos) /*!< 4KB Size of the MPU protection region */
+#define LL_MPU_REGION_SIZE_8KB             (0x0CU << MPU_RASR_SIZE_Pos) /*!< 8KB Size of the MPU protection region */
+#define LL_MPU_REGION_SIZE_16KB            (0x0DU << MPU_RASR_SIZE_Pos) /*!< 16KB Size of the MPU protection region */
+#define LL_MPU_REGION_SIZE_32KB            (0x0EU << MPU_RASR_SIZE_Pos) /*!< 32KB Size of the MPU protection region */
+#define LL_MPU_REGION_SIZE_64KB            (0x0FU << MPU_RASR_SIZE_Pos) /*!< 64KB Size of the MPU protection region */
+#define LL_MPU_REGION_SIZE_128KB           (0x10U << MPU_RASR_SIZE_Pos) /*!< 128KB Size of the MPU protection region */
+#define LL_MPU_REGION_SIZE_256KB           (0x11U << MPU_RASR_SIZE_Pos) /*!< 256KB Size of the MPU protection region */
+#define LL_MPU_REGION_SIZE_512KB           (0x12U << MPU_RASR_SIZE_Pos) /*!< 512KB Size of the MPU protection region */
+#define LL_MPU_REGION_SIZE_1MB             (0x13U << MPU_RASR_SIZE_Pos) /*!< 1MB Size of the MPU protection region */
+#define LL_MPU_REGION_SIZE_2MB             (0x14U << MPU_RASR_SIZE_Pos) /*!< 2MB Size of the MPU protection region */
+#define LL_MPU_REGION_SIZE_4MB             (0x15U << MPU_RASR_SIZE_Pos) /*!< 4MB Size of the MPU protection region */
+#define LL_MPU_REGION_SIZE_8MB             (0x16U << MPU_RASR_SIZE_Pos) /*!< 8MB Size of the MPU protection region */
+#define LL_MPU_REGION_SIZE_16MB            (0x17U << MPU_RASR_SIZE_Pos) /*!< 16MB Size of the MPU protection region */
+#define LL_MPU_REGION_SIZE_32MB            (0x18U << MPU_RASR_SIZE_Pos) /*!< 32MB Size of the MPU protection region */
+#define LL_MPU_REGION_SIZE_64MB            (0x19U << MPU_RASR_SIZE_Pos) /*!< 64MB Size of the MPU protection region */
+#define LL_MPU_REGION_SIZE_128MB           (0x1AU << MPU_RASR_SIZE_Pos) /*!< 128MB Size of the MPU protection region */
+#define LL_MPU_REGION_SIZE_256MB           (0x1BU << MPU_RASR_SIZE_Pos) /*!< 256MB Size of the MPU protection region */
+#define LL_MPU_REGION_SIZE_512MB           (0x1CU << MPU_RASR_SIZE_Pos) /*!< 512MB Size of the MPU protection region */
+#define LL_MPU_REGION_SIZE_1GB             (0x1DU << MPU_RASR_SIZE_Pos) /*!< 1GB Size of the MPU protection region */
+#define LL_MPU_REGION_SIZE_2GB             (0x1EU << MPU_RASR_SIZE_Pos) /*!< 2GB Size of the MPU protection region */
+#define LL_MPU_REGION_SIZE_4GB             (0x1FU << MPU_RASR_SIZE_Pos) /*!< 4GB Size of the MPU protection region */
+/**
+  * @}
+  */
+
+/** @defgroup CORTEX_LL_EC_REGION_PRIVILEDGES MPU Region Privileges
+  * @{
+  */
+#define LL_MPU_REGION_NO_ACCESS            (0x00U << MPU_RASR_AP_Pos) /*!< No access*/
+#define LL_MPU_REGION_PRIV_RW              (0x01U << MPU_RASR_AP_Pos) /*!< RW privileged (privileged access only)*/
+#define LL_MPU_REGION_PRIV_RW_URO          (0x02U << MPU_RASR_AP_Pos) /*!< RW privileged - RO user (Write in a user program generates a fault) */
+#define LL_MPU_REGION_FULL_ACCESS          (0x03U << MPU_RASR_AP_Pos) /*!< RW privileged & user (Full access) */
+#define LL_MPU_REGION_PRIV_RO              (0x05U << MPU_RASR_AP_Pos) /*!< RO privileged (privileged read only)*/
+#define LL_MPU_REGION_PRIV_RO_URO          (0x06U << MPU_RASR_AP_Pos) /*!< RO privileged & user (read only) */
+/**
+  * @}
+  */
+
+/** @defgroup CORTEX_LL_EC_TEX MPU TEX Level
+  * @{
+  */
+#define LL_MPU_TEX_LEVEL0                  (0x00U << MPU_RASR_TEX_Pos) /*!< b000 for TEX bits */
+#define LL_MPU_TEX_LEVEL1                  (0x01U << MPU_RASR_TEX_Pos) /*!< b001 for TEX bits */
+#define LL_MPU_TEX_LEVEL2                  (0x02U << MPU_RASR_TEX_Pos) /*!< b010 for TEX bits */
+#define LL_MPU_TEX_LEVEL4                  (0x04U << MPU_RASR_TEX_Pos) /*!< b100 for TEX bits */
+/**
+  * @}
+  */
+
+/** @defgroup CORTEX_LL_EC_INSTRUCTION_ACCESS MPU Instruction Access
+  * @{
+  */
+#define LL_MPU_INSTRUCTION_ACCESS_ENABLE   0x00U            /*!< Instruction fetches enabled */
+#define LL_MPU_INSTRUCTION_ACCESS_DISABLE  MPU_RASR_XN_Msk  /*!< Instruction fetches disabled*/
+/**
+  * @}
+  */
+
+/** @defgroup CORTEX_LL_EC_SHAREABLE_ACCESS MPU Shareable Access
+  * @{
+  */
+#define LL_MPU_ACCESS_SHAREABLE            MPU_RASR_S_Msk   /*!< Shareable memory attribute */
+#define LL_MPU_ACCESS_NOT_SHAREABLE        0x00U            /*!< Not Shareable memory attribute */
+/**
+  * @}
+  */
+
+/** @defgroup CORTEX_LL_EC_CACHEABLE_ACCESS MPU Cacheable Access
+  * @{
+  */
+#define LL_MPU_ACCESS_CACHEABLE            MPU_RASR_C_Msk   /*!< Cacheable memory attribute */
+#define LL_MPU_ACCESS_NOT_CACHEABLE        0x00U            /*!< Not Cacheable memory attribute */
+/**
+  * @}
+  */
+
+/** @defgroup CORTEX_LL_EC_BUFFERABLE_ACCESS MPU Bufferable Access
+  * @{
+  */
+#define LL_MPU_ACCESS_BUFFERABLE           MPU_RASR_B_Msk   /*!< Bufferable memory attribute */
+#define LL_MPU_ACCESS_NOT_BUFFERABLE       0x00U            /*!< Not Bufferable memory attribute */
+/**
+  * @}
+  */
+#endif /* __MPU_PRESENT */
+/**
+  * @}
+  */
+
+/* Exported macro ------------------------------------------------------------*/
+
+/* Exported functions --------------------------------------------------------*/
+/** @defgroup CORTEX_LL_Exported_Functions CORTEX Exported Functions
+  * @{
+  */
+
+/** @defgroup CORTEX_LL_EF_SYSTICK SYSTICK
+  * @{
+  */
+
+/**
+  * @brief  This function checks if the Systick counter flag is active or not.
+  * @note   It can be used in timeout function on application side.
+  * @rmtoll STK_CTRL     COUNTFLAG     LL_SYSTICK_IsActiveCounterFlag
+  * @retval State of bit (1 or 0).
+  */
+__STATIC_INLINE uint32_t LL_SYSTICK_IsActiveCounterFlag(void)
+{
+  return ((SysTick->CTRL & SysTick_CTRL_COUNTFLAG_Msk) == (SysTick_CTRL_COUNTFLAG_Msk));
+}
+
+/**
+  * @brief  Configures the SysTick clock source
+  * @rmtoll STK_CTRL     CLKSOURCE     LL_SYSTICK_SetClkSource
+  * @param  Source This parameter can be one of the following values:
+  *         @arg @ref LL_SYSTICK_CLKSOURCE_HCLK_DIV8
+  *         @arg @ref LL_SYSTICK_CLKSOURCE_HCLK
+  * @retval None
+  */
+__STATIC_INLINE void LL_SYSTICK_SetClkSource(uint32_t Source)
+{
+  if (Source == LL_SYSTICK_CLKSOURCE_HCLK)
+  {
+    SET_BIT(SysTick->CTRL, LL_SYSTICK_CLKSOURCE_HCLK);
+  }
+  else
+  {
+    CLEAR_BIT(SysTick->CTRL, LL_SYSTICK_CLKSOURCE_HCLK);
+  }
+}
+
+/**
+  * @brief  Get the SysTick clock source
+  * @rmtoll STK_CTRL     CLKSOURCE     LL_SYSTICK_GetClkSource
+  * @retval Returned value can be one of the following values:
+  *         @arg @ref LL_SYSTICK_CLKSOURCE_HCLK_DIV8
+  *         @arg @ref LL_SYSTICK_CLKSOURCE_HCLK
+  */
+__STATIC_INLINE uint32_t LL_SYSTICK_GetClkSource(void)
+{
+  return READ_BIT(SysTick->CTRL, LL_SYSTICK_CLKSOURCE_HCLK);
+}
+
+/**
+  * @brief  Enable SysTick exception request
+  * @rmtoll STK_CTRL     TICKINT       LL_SYSTICK_EnableIT
+  * @retval None
+  */
+__STATIC_INLINE void LL_SYSTICK_EnableIT(void)
+{
+  SET_BIT(SysTick->CTRL, SysTick_CTRL_TICKINT_Msk);
+}
+
+/**
+  * @brief  Disable SysTick exception request
+  * @rmtoll STK_CTRL     TICKINT       LL_SYSTICK_DisableIT
+  * @retval None
+  */
+__STATIC_INLINE void LL_SYSTICK_DisableIT(void)
+{
+  CLEAR_BIT(SysTick->CTRL, SysTick_CTRL_TICKINT_Msk);
+}
+
+/**
+  * @brief  Checks if the SYSTICK interrupt is enabled or disabled.
+  * @rmtoll STK_CTRL     TICKINT       LL_SYSTICK_IsEnabledIT
+  * @retval State of bit (1 or 0).
+  */
+__STATIC_INLINE uint32_t LL_SYSTICK_IsEnabledIT(void)
+{
+  return (READ_BIT(SysTick->CTRL, SysTick_CTRL_TICKINT_Msk) == (SysTick_CTRL_TICKINT_Msk));
+}
+
+/**
+  * @}
+  */
+
+/** @defgroup CORTEX_LL_EF_LOW_POWER_MODE LOW POWER MODE
+  * @{
+  */
+
+/**
+  * @brief  Processor uses sleep as its low power mode
+  * @rmtoll SCB_SCR      SLEEPDEEP     LL_LPM_EnableSleep
+  * @retval None
+  */
+__STATIC_INLINE void LL_LPM_EnableSleep(void)
+{
+  /* Clear SLEEPDEEP bit of Cortex System Control Register */
+  CLEAR_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SLEEPDEEP_Msk));
+}
+
+/**
+  * @brief  Processor uses deep sleep as its low power mode
+  * @rmtoll SCB_SCR      SLEEPDEEP     LL_LPM_EnableDeepSleep
+  * @retval None
+  */
+__STATIC_INLINE void LL_LPM_EnableDeepSleep(void)
+{
+  /* Set SLEEPDEEP bit of Cortex System Control Register */
+  SET_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SLEEPDEEP_Msk));
+}
+
+/**
+  * @brief  Configures sleep-on-exit when returning from Handler mode to Thread mode.
+  * @note   Setting this bit to 1 enables an interrupt-driven application to avoid returning to an
+  *         empty main application.
+  * @rmtoll SCB_SCR      SLEEPONEXIT   LL_LPM_EnableSleepOnExit
+  * @retval None
+  */
+__STATIC_INLINE void LL_LPM_EnableSleepOnExit(void)
+{
+  /* Set SLEEPONEXIT bit of Cortex System Control Register */
+  SET_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SLEEPONEXIT_Msk));
+}
+
+/**
+  * @brief  Do not sleep when returning to Thread mode.
+  * @rmtoll SCB_SCR      SLEEPONEXIT   LL_LPM_DisableSleepOnExit
+  * @retval None
+  */
+__STATIC_INLINE void LL_LPM_DisableSleepOnExit(void)
+{
+  /* Clear SLEEPONEXIT bit of Cortex System Control Register */
+  CLEAR_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SLEEPONEXIT_Msk));
+}
+
+/**
+  * @brief  Enabled events and all interrupts, including disabled interrupts, can wakeup the
+  *         processor.
+  * @rmtoll SCB_SCR      SEVEONPEND    LL_LPM_EnableEventOnPend
+  * @retval None
+  */
+__STATIC_INLINE void LL_LPM_EnableEventOnPend(void)
+{
+  /* Set SEVEONPEND bit of Cortex System Control Register */
+  SET_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SEVONPEND_Msk));
+}
+
+/**
+  * @brief  Only enabled interrupts or events can wakeup the processor, disabled interrupts are
+  *         excluded
+  * @rmtoll SCB_SCR      SEVEONPEND    LL_LPM_DisableEventOnPend
+  * @retval None
+  */
+__STATIC_INLINE void LL_LPM_DisableEventOnPend(void)
+{
+  /* Clear SEVEONPEND bit of Cortex System Control Register */
+  CLEAR_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SEVONPEND_Msk));
+}
+
+/**
+  * @}
+  */
+
+/** @defgroup CORTEX_LL_EF_HANDLER HANDLER
+  * @{
+  */
+
+/**
+  * @brief  Enable a fault in System handler control register (SHCSR)
+  * @rmtoll SCB_SHCSR    MEMFAULTENA   LL_HANDLER_EnableFault
+  * @param  Fault This parameter can be a combination of the following values:
+  *         @arg @ref LL_HANDLER_FAULT_USG
+  *         @arg @ref LL_HANDLER_FAULT_BUS
+  *         @arg @ref LL_HANDLER_FAULT_MEM
+  * @retval None
+  */
+__STATIC_INLINE void LL_HANDLER_EnableFault(uint32_t Fault)
+{
+  /* Enable the system handler fault */
+  SET_BIT(SCB->SHCSR, Fault);
+}
+
+/**
+  * @brief  Disable a fault in System handler control register (SHCSR)
+  * @rmtoll SCB_SHCSR    MEMFAULTENA   LL_HANDLER_DisableFault
+  * @param  Fault This parameter can be a combination of the following values:
+  *         @arg @ref LL_HANDLER_FAULT_USG
+  *         @arg @ref LL_HANDLER_FAULT_BUS
+  *         @arg @ref LL_HANDLER_FAULT_MEM
+  * @retval None
+  */
+__STATIC_INLINE void LL_HANDLER_DisableFault(uint32_t Fault)
+{
+  /* Disable the system handler fault */
+  CLEAR_BIT(SCB->SHCSR, Fault);
+}
+
+/**
+  * @}
+  */
+
+/** @defgroup CORTEX_LL_EF_MCU_INFO MCU INFO
+  * @{
+  */
+
+/**
+  * @brief  Get Implementer code
+  * @rmtoll SCB_CPUID    IMPLEMENTER   LL_CPUID_GetImplementer
+  * @retval Value should be equal to 0x41 for ARM
+  */
+__STATIC_INLINE uint32_t LL_CPUID_GetImplementer(void)
+{
+  return (uint32_t)(READ_BIT(SCB->CPUID, SCB_CPUID_IMPLEMENTER_Msk) >> SCB_CPUID_IMPLEMENTER_Pos);
+}
+
+/**
+  * @brief  Get Variant number (The r value in the rnpn product revision identifier)
+  * @rmtoll SCB_CPUID    VARIANT       LL_CPUID_GetVariant
+  * @retval Value between 0 and 255 (0x1: revision 1, 0x2: revision 2)
+  */
+__STATIC_INLINE uint32_t LL_CPUID_GetVariant(void)
+{
+  return (uint32_t)(READ_BIT(SCB->CPUID, SCB_CPUID_VARIANT_Msk) >> SCB_CPUID_VARIANT_Pos);
+}
+
+/**
+  * @brief  Get Constant number
+  * @rmtoll SCB_CPUID    ARCHITECTURE  LL_CPUID_GetConstant
+  * @retval Value should be equal to 0xF for Cortex-M3 devices
+  */
+__STATIC_INLINE uint32_t LL_CPUID_GetConstant(void)
+{
+  return (uint32_t)(READ_BIT(SCB->CPUID, SCB_CPUID_ARCHITECTURE_Msk) >> SCB_CPUID_ARCHITECTURE_Pos);
+}
+
+/**
+  * @brief  Get Part number
+  * @rmtoll SCB_CPUID    PARTNO        LL_CPUID_GetParNo
+  * @retval Value should be equal to 0xC23 for Cortex-M3
+  */
+__STATIC_INLINE uint32_t LL_CPUID_GetParNo(void)
+{
+  return (uint32_t)(READ_BIT(SCB->CPUID, SCB_CPUID_PARTNO_Msk) >> SCB_CPUID_PARTNO_Pos);
+}
+
+/**
+  * @brief  Get Revision number (The p value in the rnpn product revision identifier, indicates patch release)
+  * @rmtoll SCB_CPUID    REVISION      LL_CPUID_GetRevision
+  * @retval Value between 0 and 255 (0x0: patch 0, 0x1: patch 1)
+  */
+__STATIC_INLINE uint32_t LL_CPUID_GetRevision(void)
+{
+  return (uint32_t)(READ_BIT(SCB->CPUID, SCB_CPUID_REVISION_Msk) >> SCB_CPUID_REVISION_Pos);
+}
+
+/**
+  * @}
+  */
+
+#if __MPU_PRESENT
+/** @defgroup CORTEX_LL_EF_MPU MPU
+  * @{
+  */
+
+/**
+  * @brief  Enable MPU with input options
+  * @rmtoll MPU_CTRL     ENABLE        LL_MPU_Enable
+  * @param  Options This parameter can be one of the following values:
+  *         @arg @ref LL_MPU_CTRL_HFNMI_PRIVDEF_NONE
+  *         @arg @ref LL_MPU_CTRL_HARDFAULT_NMI
+  *         @arg @ref LL_MPU_CTRL_PRIVILEGED_DEFAULT
+  *         @arg @ref LL_MPU_CTRL_HFNMI_PRIVDEF
+  * @retval None
+  */
+__STATIC_INLINE void LL_MPU_Enable(uint32_t Options)
+{
+  /* Enable the MPU*/
+  WRITE_REG(MPU->CTRL, (MPU_CTRL_ENABLE_Msk | Options));
+  /* Ensure MPU settings take effects */
+  __DSB();
+  /* Sequence instruction fetches using update settings */
+  __ISB();
+}
+
+/**
+  * @brief  Disable MPU
+  * @rmtoll MPU_CTRL     ENABLE        LL_MPU_Disable
+  * @retval None
+  */
+__STATIC_INLINE void LL_MPU_Disable(void)
+{
+  /* Make sure outstanding transfers are done */
+  __DMB();
+  /* Disable MPU*/
+  WRITE_REG(MPU->CTRL, 0U);
+}
+
+/**
+  * @brief  Check if MPU is enabled or not
+  * @rmtoll MPU_CTRL     ENABLE        LL_MPU_IsEnabled
+  * @retval State of bit (1 or 0).
+  */
+__STATIC_INLINE uint32_t LL_MPU_IsEnabled(void)
+{
+  return (READ_BIT(MPU->CTRL, MPU_CTRL_ENABLE_Msk) == (MPU_CTRL_ENABLE_Msk));
+}
+
+/**
+  * @brief  Enable a MPU region
+  * @rmtoll MPU_RASR     ENABLE        LL_MPU_EnableRegion
+  * @param  Region This parameter can be one of the following values:
+  *         @arg @ref LL_MPU_REGION_NUMBER0
+  *         @arg @ref LL_MPU_REGION_NUMBER1
+  *         @arg @ref LL_MPU_REGION_NUMBER2
+  *         @arg @ref LL_MPU_REGION_NUMBER3
+  *         @arg @ref LL_MPU_REGION_NUMBER4
+  *         @arg @ref LL_MPU_REGION_NUMBER5
+  *         @arg @ref LL_MPU_REGION_NUMBER6
+  *         @arg @ref LL_MPU_REGION_NUMBER7
+  * @retval None
+  */
+__STATIC_INLINE void LL_MPU_EnableRegion(uint32_t Region)
+{
+  /* Set Region number */
+  WRITE_REG(MPU->RNR, Region);
+  /* Enable the MPU region */
+  SET_BIT(MPU->RASR, MPU_RASR_ENABLE_Msk);
+}
+
+/**
+  * @brief  Configure and enable a region
+  * @rmtoll MPU_RNR      REGION        LL_MPU_ConfigRegion\n
+  *         MPU_RBAR     REGION        LL_MPU_ConfigRegion\n
+  *         MPU_RBAR     ADDR          LL_MPU_ConfigRegion\n
+  *         MPU_RASR     XN            LL_MPU_ConfigRegion\n
+  *         MPU_RASR     AP            LL_MPU_ConfigRegion\n
+  *         MPU_RASR     S             LL_MPU_ConfigRegion\n
+  *         MPU_RASR     C             LL_MPU_ConfigRegion\n
+  *         MPU_RASR     B             LL_MPU_ConfigRegion\n
+  *         MPU_RASR     SIZE          LL_MPU_ConfigRegion
+  * @param  Region This parameter can be one of the following values:
+  *         @arg @ref LL_MPU_REGION_NUMBER0
+  *         @arg @ref LL_MPU_REGION_NUMBER1
+  *         @arg @ref LL_MPU_REGION_NUMBER2
+  *         @arg @ref LL_MPU_REGION_NUMBER3
+  *         @arg @ref LL_MPU_REGION_NUMBER4
+  *         @arg @ref LL_MPU_REGION_NUMBER5
+  *         @arg @ref LL_MPU_REGION_NUMBER6
+  *         @arg @ref LL_MPU_REGION_NUMBER7
+  * @param  Address Value of region base address
+  * @param  SubRegionDisable Sub-region disable value between Min_Data = 0x00 and Max_Data = 0xFF
+  * @param  Attributes This parameter can be a combination of the following values:
+  *         @arg @ref LL_MPU_REGION_SIZE_32B or @ref LL_MPU_REGION_SIZE_64B or @ref LL_MPU_REGION_SIZE_128B or @ref LL_MPU_REGION_SIZE_256B or @ref LL_MPU_REGION_SIZE_512B
+  *           or @ref LL_MPU_REGION_SIZE_1KB or @ref LL_MPU_REGION_SIZE_2KB or @ref LL_MPU_REGION_SIZE_4KB or @ref LL_MPU_REGION_SIZE_8KB or @ref LL_MPU_REGION_SIZE_16KB
+  *           or @ref LL_MPU_REGION_SIZE_32KB or @ref LL_MPU_REGION_SIZE_64KB or @ref LL_MPU_REGION_SIZE_128KB or @ref LL_MPU_REGION_SIZE_256KB or @ref LL_MPU_REGION_SIZE_512KB
+  *           or @ref LL_MPU_REGION_SIZE_1MB or @ref LL_MPU_REGION_SIZE_2MB or @ref LL_MPU_REGION_SIZE_4MB or @ref LL_MPU_REGION_SIZE_8MB or @ref LL_MPU_REGION_SIZE_16MB
+  *           or @ref LL_MPU_REGION_SIZE_32MB or @ref LL_MPU_REGION_SIZE_64MB or @ref LL_MPU_REGION_SIZE_128MB or @ref LL_MPU_REGION_SIZE_256MB or @ref LL_MPU_REGION_SIZE_512MB
+  *           or @ref LL_MPU_REGION_SIZE_1GB or @ref LL_MPU_REGION_SIZE_2GB or @ref LL_MPU_REGION_SIZE_4GB
+  *         @arg @ref LL_MPU_REGION_NO_ACCESS or @ref LL_MPU_REGION_PRIV_RW or @ref LL_MPU_REGION_PRIV_RW_URO or @ref LL_MPU_REGION_FULL_ACCESS
+  *           or @ref LL_MPU_REGION_PRIV_RO or @ref LL_MPU_REGION_PRIV_RO_URO
+  *         @arg @ref LL_MPU_TEX_LEVEL0 or @ref LL_MPU_TEX_LEVEL1 or @ref LL_MPU_TEX_LEVEL2 or @ref LL_MPU_TEX_LEVEL4
+  *         @arg @ref LL_MPU_INSTRUCTION_ACCESS_ENABLE or  @ref LL_MPU_INSTRUCTION_ACCESS_DISABLE
+  *         @arg @ref LL_MPU_ACCESS_SHAREABLE or @ref LL_MPU_ACCESS_NOT_SHAREABLE
+  *         @arg @ref LL_MPU_ACCESS_CACHEABLE or @ref LL_MPU_ACCESS_NOT_CACHEABLE
+  *         @arg @ref LL_MPU_ACCESS_BUFFERABLE or @ref LL_MPU_ACCESS_NOT_BUFFERABLE
+  * @retval None
+  */
+__STATIC_INLINE void LL_MPU_ConfigRegion(uint32_t Region, uint32_t SubRegionDisable, uint32_t Address, uint32_t Attributes)
+{
+  /* Set Region number */
+  WRITE_REG(MPU->RNR, Region);
+  /* Set base address */
+  WRITE_REG(MPU->RBAR, (Address & 0xFFFFFFE0U));
+  /* Configure MPU */
+  WRITE_REG(MPU->RASR, (MPU_RASR_ENABLE_Msk | Attributes | SubRegionDisable << MPU_RASR_SRD_Pos));
+}
+
+/**
+  * @brief  Disable a region
+  * @rmtoll MPU_RNR      REGION        LL_MPU_DisableRegion\n
+  *         MPU_RASR     ENABLE        LL_MPU_DisableRegion
+  * @param  Region This parameter can be one of the following values:
+  *         @arg @ref LL_MPU_REGION_NUMBER0
+  *         @arg @ref LL_MPU_REGION_NUMBER1
+  *         @arg @ref LL_MPU_REGION_NUMBER2
+  *         @arg @ref LL_MPU_REGION_NUMBER3
+  *         @arg @ref LL_MPU_REGION_NUMBER4
+  *         @arg @ref LL_MPU_REGION_NUMBER5
+  *         @arg @ref LL_MPU_REGION_NUMBER6
+  *         @arg @ref LL_MPU_REGION_NUMBER7
+  * @retval None
+  */
+__STATIC_INLINE void LL_MPU_DisableRegion(uint32_t Region)
+{
+  /* Set Region number */
+  WRITE_REG(MPU->RNR, Region);
+  /* Disable the MPU region */
+  CLEAR_BIT(MPU->RASR, MPU_RASR_ENABLE_Msk);
+}
+
+/**
+  * @}
+  */
+
+#endif /* __MPU_PRESENT */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F1xx_LL_CORTEX_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_ll_crc.h

@@ -0,0 +1,204 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_ll_crc.h
+  * @author  MCD Application Team
+  * @brief   Header file of CRC LL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef STM32F1xx_LL_CRC_H
+#define STM32F1xx_LL_CRC_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx.h"
+
+/** @addtogroup STM32F1xx_LL_Driver
+  * @{
+  */
+
+#if defined(CRC)
+
+/** @defgroup CRC_LL CRC
+  * @{
+  */
+
+/* Private types -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private constants ---------------------------------------------------------*/
+/* Private macros ------------------------------------------------------------*/
+
+/* Exported types ------------------------------------------------------------*/
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup CRC_LL_Exported_Constants CRC Exported Constants
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/* Exported macro ------------------------------------------------------------*/
+/** @defgroup CRC_LL_Exported_Macros CRC Exported Macros
+  * @{
+  */
+
+/** @defgroup CRC_LL_EM_WRITE_READ Common Write and read registers Macros
+  * @{
+  */
+
+/**
+  * @brief  Write a value in CRC register
+  * @param  __INSTANCE__ CRC Instance
+  * @param  __REG__ Register to be written
+  * @param  __VALUE__ Value to be written in the register
+  * @retval None
+  */
+#define LL_CRC_WriteReg(__INSTANCE__, __REG__, __VALUE__) WRITE_REG(__INSTANCE__->__REG__, __VALUE__)
+
+/**
+  * @brief  Read a value in CRC register
+  * @param  __INSTANCE__ CRC Instance
+  * @param  __REG__ Register to be read
+  * @retval Register value
+  */
+#define LL_CRC_ReadReg(__INSTANCE__, __REG__) READ_REG(__INSTANCE__->__REG__)
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+
+/* Exported functions --------------------------------------------------------*/
+/** @defgroup CRC_LL_Exported_Functions CRC Exported Functions
+  * @{
+  */
+
+/** @defgroup CRC_LL_EF_Configuration CRC Configuration functions
+  * @{
+  */
+
+/**
+  * @brief  Reset the CRC calculation unit.
+  * @note   If Programmable Initial CRC value feature
+  *         is available, also set the Data Register to the value stored in the
+  *         CRC_INIT register, otherwise, reset Data Register to its default value.
+  * @rmtoll CR           RESET         LL_CRC_ResetCRCCalculationUnit
+  * @param  CRCx CRC Instance
+  * @retval None
+  */
+__STATIC_INLINE void LL_CRC_ResetCRCCalculationUnit(CRC_TypeDef *CRCx)
+{
+  SET_BIT(CRCx->CR, CRC_CR_RESET);
+}
+
+/**
+  * @}
+  */
+
+/** @defgroup CRC_LL_EF_Data_Management Data_Management
+  * @{
+  */
+
+/**
+  * @brief  Write given 32-bit data to the CRC calculator
+  * @rmtoll DR           DR            LL_CRC_FeedData32
+  * @param  CRCx CRC Instance
+  * @param  InData value to be provided to CRC calculator between between Min_Data=0 and Max_Data=0xFFFFFFFF
+  * @retval None
+  */
+__STATIC_INLINE void LL_CRC_FeedData32(CRC_TypeDef *CRCx, uint32_t InData)
+{
+  WRITE_REG(CRCx->DR, InData);
+}
+
+/**
+  * @brief  Return current CRC calculation result. 32 bits value is returned.
+  * @rmtoll DR           DR            LL_CRC_ReadData32
+  * @param  CRCx CRC Instance
+  * @retval Current CRC calculation result as stored in CRC_DR register (32 bits).
+  */
+__STATIC_INLINE uint32_t LL_CRC_ReadData32(CRC_TypeDef *CRCx)
+{
+  return (uint32_t)(READ_REG(CRCx->DR));
+}
+
+/**
+  * @brief  Return data stored in the Independent Data(IDR) register.
+  * @note   This register can be used as a temporary storage location for one byte.
+  * @rmtoll IDR          IDR           LL_CRC_Read_IDR
+  * @param  CRCx CRC Instance
+  * @retval Value stored in CRC_IDR register (General-purpose 8-bit data register).
+  */
+__STATIC_INLINE uint32_t LL_CRC_Read_IDR(CRC_TypeDef *CRCx)
+{
+  return (uint32_t)(READ_REG(CRCx->IDR));
+}
+
+/**
+  * @brief  Store data in the Independent Data(IDR) register.
+  * @note   This register can be used as a temporary storage location for one byte.
+  * @rmtoll IDR          IDR           LL_CRC_Write_IDR
+  * @param  CRCx CRC Instance
+  * @param  InData value to be stored in CRC_IDR register (8-bit) between Min_Data=0 and Max_Data=0xFF
+  * @retval None
+  */
+__STATIC_INLINE void LL_CRC_Write_IDR(CRC_TypeDef *CRCx, uint32_t InData)
+{
+  *((uint8_t __IO *)(&CRCx->IDR)) = (uint8_t) InData;
+}
+/**
+  * @}
+  */
+
+#if defined(USE_FULL_LL_DRIVER)
+/** @defgroup CRC_LL_EF_Init Initialization and de-initialization functions
+  * @{
+  */
+
+ErrorStatus LL_CRC_DeInit(CRC_TypeDef *CRCx);
+
+/**
+  * @}
+  */
+#endif /* USE_FULL_LL_DRIVER */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#endif /* defined(CRC) */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* STM32F1xx_LL_CRC_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_ll_exti.h

@@ -0,0 +1,888 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_ll_exti.h
+  * @author  MCD Application Team
+  * @brief   Header file of EXTI LL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                        opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef STM32F1xx_LL_EXTI_H
+#define STM32F1xx_LL_EXTI_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx.h"
+
+/** @addtogroup STM32F1xx_LL_Driver
+  * @{
+  */
+
+#if defined (EXTI)
+
+/** @defgroup EXTI_LL EXTI
+  * @{
+  */
+
+/* Private types -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private constants ---------------------------------------------------------*/
+/* Private Macros ------------------------------------------------------------*/
+#if defined(USE_FULL_LL_DRIVER)
+/** @defgroup EXTI_LL_Private_Macros EXTI Private Macros
+  * @{
+  */
+/**
+  * @}
+  */
+#endif /*USE_FULL_LL_DRIVER*/
+/* Exported types ------------------------------------------------------------*/
+#if defined(USE_FULL_LL_DRIVER)
+/** @defgroup EXTI_LL_ES_INIT EXTI Exported Init structure
+  * @{
+  */
+typedef struct
+{
+
+  uint32_t Line_0_31;           /*!< Specifies the EXTI lines to be enabled or disabled for Lines in range 0 to 31
+                                     This parameter can be any combination of @ref EXTI_LL_EC_LINE */
+
+  FunctionalState LineCommand;  /*!< Specifies the new state of the selected EXTI lines.
+                                     This parameter can be set either to ENABLE or DISABLE */
+
+  uint8_t Mode;                 /*!< Specifies the mode for the EXTI lines.
+                                     This parameter can be a value of @ref EXTI_LL_EC_MODE. */
+
+  uint8_t Trigger;              /*!< Specifies the trigger signal active edge for the EXTI lines.
+                                     This parameter can be a value of @ref EXTI_LL_EC_TRIGGER. */
+} LL_EXTI_InitTypeDef;
+
+/**
+  * @}
+  */
+#endif /*USE_FULL_LL_DRIVER*/
+
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup EXTI_LL_Exported_Constants EXTI Exported Constants
+  * @{
+  */
+
+/** @defgroup EXTI_LL_EC_LINE LINE
+  * @{
+  */
+#define LL_EXTI_LINE_0                 EXTI_IMR_IM0           /*!< Extended line 0 */
+#define LL_EXTI_LINE_1                 EXTI_IMR_IM1           /*!< Extended line 1 */
+#define LL_EXTI_LINE_2                 EXTI_IMR_IM2           /*!< Extended line 2 */
+#define LL_EXTI_LINE_3                 EXTI_IMR_IM3           /*!< Extended line 3 */
+#define LL_EXTI_LINE_4                 EXTI_IMR_IM4           /*!< Extended line 4 */
+#define LL_EXTI_LINE_5                 EXTI_IMR_IM5           /*!< Extended line 5 */
+#define LL_EXTI_LINE_6                 EXTI_IMR_IM6           /*!< Extended line 6 */
+#define LL_EXTI_LINE_7                 EXTI_IMR_IM7           /*!< Extended line 7 */
+#define LL_EXTI_LINE_8                 EXTI_IMR_IM8           /*!< Extended line 8 */
+#define LL_EXTI_LINE_9                 EXTI_IMR_IM9           /*!< Extended line 9 */
+#define LL_EXTI_LINE_10                EXTI_IMR_IM10          /*!< Extended line 10 */
+#define LL_EXTI_LINE_11                EXTI_IMR_IM11          /*!< Extended line 11 */
+#define LL_EXTI_LINE_12                EXTI_IMR_IM12          /*!< Extended line 12 */
+#define LL_EXTI_LINE_13                EXTI_IMR_IM13          /*!< Extended line 13 */
+#define LL_EXTI_LINE_14                EXTI_IMR_IM14          /*!< Extended line 14 */
+#define LL_EXTI_LINE_15                EXTI_IMR_IM15          /*!< Extended line 15 */
+#if defined(EXTI_IMR_IM16)
+#define LL_EXTI_LINE_16                EXTI_IMR_IM16          /*!< Extended line 16 */
+#endif
+#define LL_EXTI_LINE_17                EXTI_IMR_IM17          /*!< Extended line 17 */
+#if defined(EXTI_IMR_IM18)
+#define LL_EXTI_LINE_18                EXTI_IMR_IM18          /*!< Extended line 18 */
+#endif
+#if defined(EXTI_IMR_IM19)
+#define LL_EXTI_LINE_19                EXTI_IMR_IM19          /*!< Extended line 19 */
+#endif
+#if defined(EXTI_IMR_IM20)
+#define LL_EXTI_LINE_20                EXTI_IMR_IM20          /*!< Extended line 20 */
+#endif
+#if defined(EXTI_IMR_IM21)
+#define LL_EXTI_LINE_21                EXTI_IMR_IM21          /*!< Extended line 21 */
+#endif
+#if defined(EXTI_IMR_IM22)
+#define LL_EXTI_LINE_22                EXTI_IMR_IM22          /*!< Extended line 22 */
+#endif
+#if defined(EXTI_IMR_IM23)
+#define LL_EXTI_LINE_23                EXTI_IMR_IM23          /*!< Extended line 23 */
+#endif
+#if defined(EXTI_IMR_IM24)
+#define LL_EXTI_LINE_24                EXTI_IMR_IM24          /*!< Extended line 24 */
+#endif
+#if defined(EXTI_IMR_IM25)
+#define LL_EXTI_LINE_25                EXTI_IMR_IM25          /*!< Extended line 25 */
+#endif
+#if defined(EXTI_IMR_IM26)
+#define LL_EXTI_LINE_26                EXTI_IMR_IM26          /*!< Extended line 26 */
+#endif
+#if defined(EXTI_IMR_IM27)
+#define LL_EXTI_LINE_27                EXTI_IMR_IM27          /*!< Extended line 27 */
+#endif
+#if defined(EXTI_IMR_IM28)
+#define LL_EXTI_LINE_28                EXTI_IMR_IM28          /*!< Extended line 28 */
+#endif
+#if defined(EXTI_IMR_IM29)
+#define LL_EXTI_LINE_29                EXTI_IMR_IM29          /*!< Extended line 29 */
+#endif
+#if defined(EXTI_IMR_IM30)
+#define LL_EXTI_LINE_30                EXTI_IMR_IM30          /*!< Extended line 30 */
+#endif
+#if defined(EXTI_IMR_IM31)
+#define LL_EXTI_LINE_31                EXTI_IMR_IM31          /*!< Extended line 31 */
+#endif
+#define LL_EXTI_LINE_ALL_0_31          EXTI_IMR_IM            /*!< All Extended line not reserved*/
+
+
+#define LL_EXTI_LINE_ALL               (0xFFFFFFFFU)  /*!< All Extended line */
+
+#if defined(USE_FULL_LL_DRIVER)
+#define LL_EXTI_LINE_NONE              (0x00000000U)  /*!< None Extended line */
+#endif /*USE_FULL_LL_DRIVER*/
+
+/**
+  * @}
+  */
+#if defined(USE_FULL_LL_DRIVER)
+
+/** @defgroup EXTI_LL_EC_MODE Mode
+  * @{
+  */
+#define LL_EXTI_MODE_IT                 ((uint8_t)0x00) /*!< Interrupt Mode */
+#define LL_EXTI_MODE_EVENT              ((uint8_t)0x01) /*!< Event Mode */
+#define LL_EXTI_MODE_IT_EVENT           ((uint8_t)0x02) /*!< Interrupt & Event Mode */
+/**
+  * @}
+  */
+
+/** @defgroup EXTI_LL_EC_TRIGGER Edge Trigger
+  * @{
+  */
+#define LL_EXTI_TRIGGER_NONE            ((uint8_t)0x00) /*!< No Trigger Mode */
+#define LL_EXTI_TRIGGER_RISING          ((uint8_t)0x01) /*!< Trigger Rising Mode */
+#define LL_EXTI_TRIGGER_FALLING         ((uint8_t)0x02) /*!< Trigger Falling Mode */
+#define LL_EXTI_TRIGGER_RISING_FALLING  ((uint8_t)0x03) /*!< Trigger Rising & Falling Mode */
+
+/**
+  * @}
+  */
+
+
+#endif /*USE_FULL_LL_DRIVER*/
+
+
+/**
+  * @}
+  */
+
+/* Exported macro ------------------------------------------------------------*/
+/** @defgroup EXTI_LL_Exported_Macros EXTI Exported Macros
+  * @{
+  */
+
+/** @defgroup EXTI_LL_EM_WRITE_READ Common Write and read registers Macros
+  * @{
+  */
+
+/**
+  * @brief  Write a value in EXTI register
+  * @param  __REG__ Register to be written
+  * @param  __VALUE__ Value to be written in the register
+  * @retval None
+  */
+#define LL_EXTI_WriteReg(__REG__, __VALUE__) WRITE_REG(EXTI->__REG__, (__VALUE__))
+
+/**
+  * @brief  Read a value in EXTI register
+  * @param  __REG__ Register to be read
+  * @retval Register value
+  */
+#define LL_EXTI_ReadReg(__REG__) READ_REG(EXTI->__REG__)
+/**
+  * @}
+  */
+
+
+/**
+  * @}
+  */
+
+
+
+/* Exported functions --------------------------------------------------------*/
+/** @defgroup EXTI_LL_Exported_Functions EXTI Exported Functions
+ * @{
+ */
+/** @defgroup EXTI_LL_EF_IT_Management IT_Management
+  * @{
+  */
+
+/**
+  * @brief  Enable ExtiLine Interrupt request for Lines in range 0 to 31
+  * @note The reset value for the direct or internal lines (see RM)
+  *       is set to 1 in order to enable the interrupt by default.
+  *       Bits are set automatically at Power on.
+  * @rmtoll IMR         IMx           LL_EXTI_EnableIT_0_31
+  * @param  ExtiLine This parameter can be one of the following values:
+  *         @arg @ref LL_EXTI_LINE_0
+  *         @arg @ref LL_EXTI_LINE_1
+  *         @arg @ref LL_EXTI_LINE_2
+  *         @arg @ref LL_EXTI_LINE_3
+  *         @arg @ref LL_EXTI_LINE_4
+  *         @arg @ref LL_EXTI_LINE_5
+  *         @arg @ref LL_EXTI_LINE_6
+  *         @arg @ref LL_EXTI_LINE_7
+  *         @arg @ref LL_EXTI_LINE_8
+  *         @arg @ref LL_EXTI_LINE_9
+  *         @arg @ref LL_EXTI_LINE_10
+  *         @arg @ref LL_EXTI_LINE_11
+  *         @arg @ref LL_EXTI_LINE_12
+  *         @arg @ref LL_EXTI_LINE_13
+  *         @arg @ref LL_EXTI_LINE_14
+  *         @arg @ref LL_EXTI_LINE_15
+  *         @arg @ref LL_EXTI_LINE_16
+  *         @arg @ref LL_EXTI_LINE_17
+  *         @arg @ref LL_EXTI_LINE_18
+  *         @arg @ref LL_EXTI_LINE_19
+  *         @arg @ref LL_EXTI_LINE_ALL_0_31
+  * @note   Please check each device line mapping for EXTI Line availability
+  * @retval None
+  */
+__STATIC_INLINE void LL_EXTI_EnableIT_0_31(uint32_t ExtiLine)
+{
+  SET_BIT(EXTI->IMR, ExtiLine);
+}
+
+/**
+  * @brief  Disable ExtiLine Interrupt request for Lines in range 0 to 31
+  * @note The reset value for the direct or internal lines (see RM)
+  *       is set to 1 in order to enable the interrupt by default.
+  *       Bits are set automatically at Power on.
+  * @rmtoll IMR         IMx           LL_EXTI_DisableIT_0_31
+  * @param  ExtiLine This parameter can be one of the following values:
+  *         @arg @ref LL_EXTI_LINE_0
+  *         @arg @ref LL_EXTI_LINE_1
+  *         @arg @ref LL_EXTI_LINE_2
+  *         @arg @ref LL_EXTI_LINE_3
+  *         @arg @ref LL_EXTI_LINE_4
+  *         @arg @ref LL_EXTI_LINE_5
+  *         @arg @ref LL_EXTI_LINE_6
+  *         @arg @ref LL_EXTI_LINE_7
+  *         @arg @ref LL_EXTI_LINE_8
+  *         @arg @ref LL_EXTI_LINE_9
+  *         @arg @ref LL_EXTI_LINE_10
+  *         @arg @ref LL_EXTI_LINE_11
+  *         @arg @ref LL_EXTI_LINE_12
+  *         @arg @ref LL_EXTI_LINE_13
+  *         @arg @ref LL_EXTI_LINE_14
+  *         @arg @ref LL_EXTI_LINE_15
+  *         @arg @ref LL_EXTI_LINE_16
+  *         @arg @ref LL_EXTI_LINE_17
+  *         @arg @ref LL_EXTI_LINE_18
+  *         @arg @ref LL_EXTI_LINE_19
+  *         @arg @ref LL_EXTI_LINE_ALL_0_31
+  * @note   Please check each device line mapping for EXTI Line availability
+  * @retval None
+  */
+__STATIC_INLINE void LL_EXTI_DisableIT_0_31(uint32_t ExtiLine)
+{
+  CLEAR_BIT(EXTI->IMR, ExtiLine);
+}
+
+
+/**
+  * @brief  Indicate if ExtiLine Interrupt request is enabled for Lines in range 0 to 31
+  * @note The reset value for the direct or internal lines (see RM)
+  *       is set to 1 in order to enable the interrupt by default.
+  *       Bits are set automatically at Power on.
+  * @rmtoll IMR         IMx           LL_EXTI_IsEnabledIT_0_31
+  * @param  ExtiLine This parameter can be one of the following values:
+  *         @arg @ref LL_EXTI_LINE_0
+  *         @arg @ref LL_EXTI_LINE_1
+  *         @arg @ref LL_EXTI_LINE_2
+  *         @arg @ref LL_EXTI_LINE_3
+  *         @arg @ref LL_EXTI_LINE_4
+  *         @arg @ref LL_EXTI_LINE_5
+  *         @arg @ref LL_EXTI_LINE_6
+  *         @arg @ref LL_EXTI_LINE_7
+  *         @arg @ref LL_EXTI_LINE_8
+  *         @arg @ref LL_EXTI_LINE_9
+  *         @arg @ref LL_EXTI_LINE_10
+  *         @arg @ref LL_EXTI_LINE_11
+  *         @arg @ref LL_EXTI_LINE_12
+  *         @arg @ref LL_EXTI_LINE_13
+  *         @arg @ref LL_EXTI_LINE_14
+  *         @arg @ref LL_EXTI_LINE_15
+  *         @arg @ref LL_EXTI_LINE_16
+  *         @arg @ref LL_EXTI_LINE_17
+  *         @arg @ref LL_EXTI_LINE_18
+  *         @arg @ref LL_EXTI_LINE_19
+  *         @arg @ref LL_EXTI_LINE_ALL_0_31
+  * @note   Please check each device line mapping for EXTI Line availability
+  * @retval State of bit (1 or 0).
+  */
+__STATIC_INLINE uint32_t LL_EXTI_IsEnabledIT_0_31(uint32_t ExtiLine)
+{
+  return (READ_BIT(EXTI->IMR, ExtiLine) == (ExtiLine));
+}
+
+
+/**
+  * @}
+  */
+
+/** @defgroup EXTI_LL_EF_Event_Management Event_Management
+  * @{
+  */
+
+/**
+  * @brief  Enable ExtiLine Event request for Lines in range 0 to 31
+  * @rmtoll EMR         EMx           LL_EXTI_EnableEvent_0_31
+  * @param  ExtiLine This parameter can be one of the following values:
+  *         @arg @ref LL_EXTI_LINE_0
+  *         @arg @ref LL_EXTI_LINE_1
+  *         @arg @ref LL_EXTI_LINE_2
+  *         @arg @ref LL_EXTI_LINE_3
+  *         @arg @ref LL_EXTI_LINE_4
+  *         @arg @ref LL_EXTI_LINE_5
+  *         @arg @ref LL_EXTI_LINE_6
+  *         @arg @ref LL_EXTI_LINE_7
+  *         @arg @ref LL_EXTI_LINE_8
+  *         @arg @ref LL_EXTI_LINE_9
+  *         @arg @ref LL_EXTI_LINE_10
+  *         @arg @ref LL_EXTI_LINE_11
+  *         @arg @ref LL_EXTI_LINE_12
+  *         @arg @ref LL_EXTI_LINE_13
+  *         @arg @ref LL_EXTI_LINE_14
+  *         @arg @ref LL_EXTI_LINE_15
+  *         @arg @ref LL_EXTI_LINE_16
+  *         @arg @ref LL_EXTI_LINE_17
+  *         @arg @ref LL_EXTI_LINE_18
+  *         @arg @ref LL_EXTI_LINE_19
+  *         @arg @ref LL_EXTI_LINE_ALL_0_31
+  * @note   Please check each device line mapping for EXTI Line availability
+  * @retval None
+  */
+__STATIC_INLINE void LL_EXTI_EnableEvent_0_31(uint32_t ExtiLine)
+{
+  SET_BIT(EXTI->EMR, ExtiLine);
+
+}
+
+
+/**
+  * @brief  Disable ExtiLine Event request for Lines in range 0 to 31
+  * @rmtoll EMR         EMx           LL_EXTI_DisableEvent_0_31
+  * @param  ExtiLine This parameter can be one of the following values:
+  *         @arg @ref LL_EXTI_LINE_0
+  *         @arg @ref LL_EXTI_LINE_1
+  *         @arg @ref LL_EXTI_LINE_2
+  *         @arg @ref LL_EXTI_LINE_3
+  *         @arg @ref LL_EXTI_LINE_4
+  *         @arg @ref LL_EXTI_LINE_5
+  *         @arg @ref LL_EXTI_LINE_6
+  *         @arg @ref LL_EXTI_LINE_7
+  *         @arg @ref LL_EXTI_LINE_8
+  *         @arg @ref LL_EXTI_LINE_9
+  *         @arg @ref LL_EXTI_LINE_10
+  *         @arg @ref LL_EXTI_LINE_11
+  *         @arg @ref LL_EXTI_LINE_12
+  *         @arg @ref LL_EXTI_LINE_13
+  *         @arg @ref LL_EXTI_LINE_14
+  *         @arg @ref LL_EXTI_LINE_15
+  *         @arg @ref LL_EXTI_LINE_16
+  *         @arg @ref LL_EXTI_LINE_17
+  *         @arg @ref LL_EXTI_LINE_18
+  *         @arg @ref LL_EXTI_LINE_19
+  *         @arg @ref LL_EXTI_LINE_ALL_0_31
+  * @note   Please check each device line mapping for EXTI Line availability
+  * @retval None
+  */
+__STATIC_INLINE void LL_EXTI_DisableEvent_0_31(uint32_t ExtiLine)
+{
+  CLEAR_BIT(EXTI->EMR, ExtiLine);
+}
+
+
+/**
+  * @brief  Indicate if ExtiLine Event request is enabled for Lines in range 0 to 31
+  * @rmtoll EMR         EMx           LL_EXTI_IsEnabledEvent_0_31
+  * @param  ExtiLine This parameter can be one of the following values:
+  *         @arg @ref LL_EXTI_LINE_0
+  *         @arg @ref LL_EXTI_LINE_1
+  *         @arg @ref LL_EXTI_LINE_2
+  *         @arg @ref LL_EXTI_LINE_3
+  *         @arg @ref LL_EXTI_LINE_4
+  *         @arg @ref LL_EXTI_LINE_5
+  *         @arg @ref LL_EXTI_LINE_6
+  *         @arg @ref LL_EXTI_LINE_7
+  *         @arg @ref LL_EXTI_LINE_8
+  *         @arg @ref LL_EXTI_LINE_9
+  *         @arg @ref LL_EXTI_LINE_10
+  *         @arg @ref LL_EXTI_LINE_11
+  *         @arg @ref LL_EXTI_LINE_12
+  *         @arg @ref LL_EXTI_LINE_13
+  *         @arg @ref LL_EXTI_LINE_14
+  *         @arg @ref LL_EXTI_LINE_15
+  *         @arg @ref LL_EXTI_LINE_16
+  *         @arg @ref LL_EXTI_LINE_17
+  *         @arg @ref LL_EXTI_LINE_18
+  *         @arg @ref LL_EXTI_LINE_19
+  *         @arg @ref LL_EXTI_LINE_ALL_0_31
+  * @note   Please check each device line mapping for EXTI Line availability
+  * @retval State of bit (1 or 0).
+  */
+__STATIC_INLINE uint32_t LL_EXTI_IsEnabledEvent_0_31(uint32_t ExtiLine)
+{
+  return (READ_BIT(EXTI->EMR, ExtiLine) == (ExtiLine));
+
+}
+
+
+/**
+  * @}
+  */
+
+/** @defgroup EXTI_LL_EF_Rising_Trigger_Management Rising_Trigger_Management
+  * @{
+  */
+
+/**
+  * @brief  Enable ExtiLine Rising Edge Trigger for Lines in range 0 to 31
+  * @note The configurable wakeup lines are edge-triggered. No glitch must be
+  *       generated on these lines. If a rising edge on a configurable interrupt
+  *       line occurs during a write operation in the EXTI_RTSR register, the
+  *       pending bit is not set.
+  *       Rising and falling edge triggers can be set for
+  *       the same interrupt line. In this case, both generate a trigger
+  *       condition.
+  * @rmtoll RTSR        RTx           LL_EXTI_EnableRisingTrig_0_31
+  * @param  ExtiLine This parameter can be a combination of the following values:
+  *         @arg @ref LL_EXTI_LINE_0
+  *         @arg @ref LL_EXTI_LINE_1
+  *         @arg @ref LL_EXTI_LINE_2
+  *         @arg @ref LL_EXTI_LINE_3
+  *         @arg @ref LL_EXTI_LINE_4
+  *         @arg @ref LL_EXTI_LINE_5
+  *         @arg @ref LL_EXTI_LINE_6
+  *         @arg @ref LL_EXTI_LINE_7
+  *         @arg @ref LL_EXTI_LINE_8
+  *         @arg @ref LL_EXTI_LINE_9
+  *         @arg @ref LL_EXTI_LINE_10
+  *         @arg @ref LL_EXTI_LINE_11
+  *         @arg @ref LL_EXTI_LINE_12
+  *         @arg @ref LL_EXTI_LINE_13
+  *         @arg @ref LL_EXTI_LINE_14
+  *         @arg @ref LL_EXTI_LINE_15
+  *         @arg @ref LL_EXTI_LINE_16
+  *         @arg @ref LL_EXTI_LINE_18
+  *         @arg @ref LL_EXTI_LINE_19
+  * @note   Please check each device line mapping for EXTI Line availability
+  * @retval None
+  */
+__STATIC_INLINE void LL_EXTI_EnableRisingTrig_0_31(uint32_t ExtiLine)
+{
+  SET_BIT(EXTI->RTSR, ExtiLine);
+
+}
+
+
+/**
+  * @brief  Disable ExtiLine Rising Edge Trigger for Lines in range 0 to 31
+  * @note The configurable wakeup lines are edge-triggered. No glitch must be
+  *       generated on these lines. If a rising edge on a configurable interrupt
+  *       line occurs during a write operation in the EXTI_RTSR register, the
+  *       pending bit is not set.
+  *       Rising and falling edge triggers can be set for
+  *       the same interrupt line. In this case, both generate a trigger
+  *       condition.
+  * @rmtoll RTSR        RTx           LL_EXTI_DisableRisingTrig_0_31
+  * @param  ExtiLine This parameter can be a combination of the following values:
+  *         @arg @ref LL_EXTI_LINE_0
+  *         @arg @ref LL_EXTI_LINE_1
+  *         @arg @ref LL_EXTI_LINE_2
+  *         @arg @ref LL_EXTI_LINE_3
+  *         @arg @ref LL_EXTI_LINE_4
+  *         @arg @ref LL_EXTI_LINE_5
+  *         @arg @ref LL_EXTI_LINE_6
+  *         @arg @ref LL_EXTI_LINE_7
+  *         @arg @ref LL_EXTI_LINE_8
+  *         @arg @ref LL_EXTI_LINE_9
+  *         @arg @ref LL_EXTI_LINE_10
+  *         @arg @ref LL_EXTI_LINE_11
+  *         @arg @ref LL_EXTI_LINE_12
+  *         @arg @ref LL_EXTI_LINE_13
+  *         @arg @ref LL_EXTI_LINE_14
+  *         @arg @ref LL_EXTI_LINE_15
+  *         @arg @ref LL_EXTI_LINE_16
+  *         @arg @ref LL_EXTI_LINE_18
+  *         @arg @ref LL_EXTI_LINE_19
+  * @note   Please check each device line mapping for EXTI Line availability
+  * @retval None
+  */
+__STATIC_INLINE void LL_EXTI_DisableRisingTrig_0_31(uint32_t ExtiLine)
+{
+  CLEAR_BIT(EXTI->RTSR, ExtiLine);
+
+}
+
+
+/**
+  * @brief  Check if rising edge trigger is enabled for Lines in range 0 to 31
+  * @rmtoll RTSR        RTx           LL_EXTI_IsEnabledRisingTrig_0_31
+  * @param  ExtiLine This parameter can be a combination of the following values:
+  *         @arg @ref LL_EXTI_LINE_0
+  *         @arg @ref LL_EXTI_LINE_1
+  *         @arg @ref LL_EXTI_LINE_2
+  *         @arg @ref LL_EXTI_LINE_3
+  *         @arg @ref LL_EXTI_LINE_4
+  *         @arg @ref LL_EXTI_LINE_5
+  *         @arg @ref LL_EXTI_LINE_6
+  *         @arg @ref LL_EXTI_LINE_7
+  *         @arg @ref LL_EXTI_LINE_8
+  *         @arg @ref LL_EXTI_LINE_9
+  *         @arg @ref LL_EXTI_LINE_10
+  *         @arg @ref LL_EXTI_LINE_11
+  *         @arg @ref LL_EXTI_LINE_12
+  *         @arg @ref LL_EXTI_LINE_13
+  *         @arg @ref LL_EXTI_LINE_14
+  *         @arg @ref LL_EXTI_LINE_15
+  *         @arg @ref LL_EXTI_LINE_16
+  *         @arg @ref LL_EXTI_LINE_18
+  *         @arg @ref LL_EXTI_LINE_19
+  * @note   Please check each device line mapping for EXTI Line availability
+  * @retval State of bit (1 or 0).
+  */
+__STATIC_INLINE uint32_t LL_EXTI_IsEnabledRisingTrig_0_31(uint32_t ExtiLine)
+{
+  return (READ_BIT(EXTI->RTSR, ExtiLine) == (ExtiLine));
+}
+
+
+/**
+  * @}
+  */
+
+/** @defgroup EXTI_LL_EF_Falling_Trigger_Management Falling_Trigger_Management
+  * @{
+  */
+
+/**
+  * @brief  Enable ExtiLine Falling Edge Trigger for Lines in range 0 to 31
+  * @note The configurable wakeup lines are edge-triggered. No glitch must be
+  *       generated on these lines. If a falling edge on a configurable interrupt
+  *       line occurs during a write operation in the EXTI_FTSR register, the
+  *       pending bit is not set.
+  *       Rising and falling edge triggers can be set for
+  *       the same interrupt line. In this case, both generate a trigger
+  *       condition.
+  * @rmtoll FTSR        FTx           LL_EXTI_EnableFallingTrig_0_31
+  * @param  ExtiLine This parameter can be a combination of the following values:
+  *         @arg @ref LL_EXTI_LINE_0
+  *         @arg @ref LL_EXTI_LINE_1
+  *         @arg @ref LL_EXTI_LINE_2
+  *         @arg @ref LL_EXTI_LINE_3
+  *         @arg @ref LL_EXTI_LINE_4
+  *         @arg @ref LL_EXTI_LINE_5
+  *         @arg @ref LL_EXTI_LINE_6
+  *         @arg @ref LL_EXTI_LINE_7
+  *         @arg @ref LL_EXTI_LINE_8
+  *         @arg @ref LL_EXTI_LINE_9
+  *         @arg @ref LL_EXTI_LINE_10
+  *         @arg @ref LL_EXTI_LINE_11
+  *         @arg @ref LL_EXTI_LINE_12
+  *         @arg @ref LL_EXTI_LINE_13
+  *         @arg @ref LL_EXTI_LINE_14
+  *         @arg @ref LL_EXTI_LINE_15
+  *         @arg @ref LL_EXTI_LINE_16
+  *         @arg @ref LL_EXTI_LINE_18
+  *         @arg @ref LL_EXTI_LINE_19
+  * @note   Please check each device line mapping for EXTI Line availability
+  * @retval None
+  */
+__STATIC_INLINE void LL_EXTI_EnableFallingTrig_0_31(uint32_t ExtiLine)
+{
+  SET_BIT(EXTI->FTSR, ExtiLine);
+}
+
+
+/**
+  * @brief  Disable ExtiLine Falling Edge Trigger for Lines in range 0 to 31
+  * @note The configurable wakeup lines are edge-triggered. No glitch must be
+  *       generated on these lines. If a Falling edge on a configurable interrupt
+  *       line occurs during a write operation in the EXTI_FTSR register, the
+  *       pending bit is not set.
+  *       Rising and falling edge triggers can be set for the same interrupt line.
+  *       In this case, both generate a trigger condition.
+  * @rmtoll FTSR        FTx           LL_EXTI_DisableFallingTrig_0_31
+  * @param  ExtiLine This parameter can be a combination of the following values:
+  *         @arg @ref LL_EXTI_LINE_0
+  *         @arg @ref LL_EXTI_LINE_1
+  *         @arg @ref LL_EXTI_LINE_2
+  *         @arg @ref LL_EXTI_LINE_3
+  *         @arg @ref LL_EXTI_LINE_4
+  *         @arg @ref LL_EXTI_LINE_5
+  *         @arg @ref LL_EXTI_LINE_6
+  *         @arg @ref LL_EXTI_LINE_7
+  *         @arg @ref LL_EXTI_LINE_8
+  *         @arg @ref LL_EXTI_LINE_9
+  *         @arg @ref LL_EXTI_LINE_10
+  *         @arg @ref LL_EXTI_LINE_11
+  *         @arg @ref LL_EXTI_LINE_12
+  *         @arg @ref LL_EXTI_LINE_13
+  *         @arg @ref LL_EXTI_LINE_14
+  *         @arg @ref LL_EXTI_LINE_15
+  *         @arg @ref LL_EXTI_LINE_16
+  *         @arg @ref LL_EXTI_LINE_18
+  *         @arg @ref LL_EXTI_LINE_19
+  * @note   Please check each device line mapping for EXTI Line availability
+  * @retval None
+  */
+__STATIC_INLINE void LL_EXTI_DisableFallingTrig_0_31(uint32_t ExtiLine)
+{
+  CLEAR_BIT(EXTI->FTSR, ExtiLine);
+}
+
+
+/**
+  * @brief  Check if falling edge trigger is enabled for Lines in range 0 to 31
+  * @rmtoll FTSR        FTx           LL_EXTI_IsEnabledFallingTrig_0_31
+  * @param  ExtiLine This parameter can be a combination of the following values:
+  *         @arg @ref LL_EXTI_LINE_0
+  *         @arg @ref LL_EXTI_LINE_1
+  *         @arg @ref LL_EXTI_LINE_2
+  *         @arg @ref LL_EXTI_LINE_3
+  *         @arg @ref LL_EXTI_LINE_4
+  *         @arg @ref LL_EXTI_LINE_5
+  *         @arg @ref LL_EXTI_LINE_6
+  *         @arg @ref LL_EXTI_LINE_7
+  *         @arg @ref LL_EXTI_LINE_8
+  *         @arg @ref LL_EXTI_LINE_9
+  *         @arg @ref LL_EXTI_LINE_10
+  *         @arg @ref LL_EXTI_LINE_11
+  *         @arg @ref LL_EXTI_LINE_12
+  *         @arg @ref LL_EXTI_LINE_13
+  *         @arg @ref LL_EXTI_LINE_14
+  *         @arg @ref LL_EXTI_LINE_15
+  *         @arg @ref LL_EXTI_LINE_16
+  *         @arg @ref LL_EXTI_LINE_18
+  *         @arg @ref LL_EXTI_LINE_19
+  * @note   Please check each device line mapping for EXTI Line availability
+  * @retval State of bit (1 or 0).
+  */
+__STATIC_INLINE uint32_t LL_EXTI_IsEnabledFallingTrig_0_31(uint32_t ExtiLine)
+{
+  return (READ_BIT(EXTI->FTSR, ExtiLine) == (ExtiLine));
+}
+
+
+/**
+  * @}
+  */
+
+/** @defgroup EXTI_LL_EF_Software_Interrupt_Management Software_Interrupt_Management
+  * @{
+  */
+
+/**
+  * @brief  Generate a software Interrupt Event for Lines in range 0 to 31
+  * @note If the interrupt is enabled on this line in the EXTI_IMR, writing a 1 to
+  *       this bit when it is at '0' sets the corresponding pending bit in EXTI_PR
+  *       resulting in an interrupt request generation.
+  *       This bit is cleared by clearing the corresponding bit in the EXTI_PR
+  *       register (by writing a 1 into the bit)
+  * @rmtoll SWIER       SWIx          LL_EXTI_GenerateSWI_0_31
+  * @param  ExtiLine This parameter can be a combination of the following values:
+  *         @arg @ref LL_EXTI_LINE_0
+  *         @arg @ref LL_EXTI_LINE_1
+  *         @arg @ref LL_EXTI_LINE_2
+  *         @arg @ref LL_EXTI_LINE_3
+  *         @arg @ref LL_EXTI_LINE_4
+  *         @arg @ref LL_EXTI_LINE_5
+  *         @arg @ref LL_EXTI_LINE_6
+  *         @arg @ref LL_EXTI_LINE_7
+  *         @arg @ref LL_EXTI_LINE_8
+  *         @arg @ref LL_EXTI_LINE_9
+  *         @arg @ref LL_EXTI_LINE_10
+  *         @arg @ref LL_EXTI_LINE_11
+  *         @arg @ref LL_EXTI_LINE_12
+  *         @arg @ref LL_EXTI_LINE_13
+  *         @arg @ref LL_EXTI_LINE_14
+  *         @arg @ref LL_EXTI_LINE_15
+  *         @arg @ref LL_EXTI_LINE_16
+  *         @arg @ref LL_EXTI_LINE_18
+  *         @arg @ref LL_EXTI_LINE_19
+  * @note   Please check each device line mapping for EXTI Line availability
+  * @retval None
+  */
+__STATIC_INLINE void LL_EXTI_GenerateSWI_0_31(uint32_t ExtiLine)
+{
+  SET_BIT(EXTI->SWIER, ExtiLine);
+}
+
+
+/**
+  * @}
+  */
+
+/** @defgroup EXTI_LL_EF_Flag_Management Flag_Management
+  * @{
+  */
+
+/**
+  * @brief  Check if the ExtLine Flag is set or not for Lines in range 0 to 31
+  * @note This bit is set when the selected edge event arrives on the interrupt
+  *       line. This bit is cleared by writing a 1 to the bit.
+  * @rmtoll PR          PIFx           LL_EXTI_IsActiveFlag_0_31
+  * @param  ExtiLine This parameter can be a combination of the following values:
+  *         @arg @ref LL_EXTI_LINE_0
+  *         @arg @ref LL_EXTI_LINE_1
+  *         @arg @ref LL_EXTI_LINE_2
+  *         @arg @ref LL_EXTI_LINE_3
+  *         @arg @ref LL_EXTI_LINE_4
+  *         @arg @ref LL_EXTI_LINE_5
+  *         @arg @ref LL_EXTI_LINE_6
+  *         @arg @ref LL_EXTI_LINE_7
+  *         @arg @ref LL_EXTI_LINE_8
+  *         @arg @ref LL_EXTI_LINE_9
+  *         @arg @ref LL_EXTI_LINE_10
+  *         @arg @ref LL_EXTI_LINE_11
+  *         @arg @ref LL_EXTI_LINE_12
+  *         @arg @ref LL_EXTI_LINE_13
+  *         @arg @ref LL_EXTI_LINE_14
+  *         @arg @ref LL_EXTI_LINE_15
+  *         @arg @ref LL_EXTI_LINE_16
+  *         @arg @ref LL_EXTI_LINE_18
+  *         @arg @ref LL_EXTI_LINE_19
+  * @note   Please check each device line mapping for EXTI Line availability
+  * @retval State of bit (1 or 0).
+  */
+__STATIC_INLINE uint32_t LL_EXTI_IsActiveFlag_0_31(uint32_t ExtiLine)
+{
+  return (READ_BIT(EXTI->PR, ExtiLine) == (ExtiLine));
+}
+
+
+/**
+  * @brief  Read ExtLine Combination Flag for Lines in range 0 to 31
+  * @note This bit is set when the selected edge event arrives on the interrupt
+  *       line. This bit is cleared by writing a 1 to the bit.
+  * @rmtoll PR          PIFx           LL_EXTI_ReadFlag_0_31
+  * @param  ExtiLine This parameter can be a combination of the following values:
+  *         @arg @ref LL_EXTI_LINE_0
+  *         @arg @ref LL_EXTI_LINE_1
+  *         @arg @ref LL_EXTI_LINE_2
+  *         @arg @ref LL_EXTI_LINE_3
+  *         @arg @ref LL_EXTI_LINE_4
+  *         @arg @ref LL_EXTI_LINE_5
+  *         @arg @ref LL_EXTI_LINE_6
+  *         @arg @ref LL_EXTI_LINE_7
+  *         @arg @ref LL_EXTI_LINE_8
+  *         @arg @ref LL_EXTI_LINE_9
+  *         @arg @ref LL_EXTI_LINE_10
+  *         @arg @ref LL_EXTI_LINE_11
+  *         @arg @ref LL_EXTI_LINE_12
+  *         @arg @ref LL_EXTI_LINE_13
+  *         @arg @ref LL_EXTI_LINE_14
+  *         @arg @ref LL_EXTI_LINE_15
+  *         @arg @ref LL_EXTI_LINE_16
+  *         @arg @ref LL_EXTI_LINE_18
+  *         @arg @ref LL_EXTI_LINE_19
+  * @note   Please check each device line mapping for EXTI Line availability
+  * @retval @note This bit is set when the selected edge event arrives on the interrupt
+  */
+__STATIC_INLINE uint32_t LL_EXTI_ReadFlag_0_31(uint32_t ExtiLine)
+{
+  return (uint32_t)(READ_BIT(EXTI->PR, ExtiLine));
+}
+
+
+/**
+  * @brief  Clear ExtLine Flags  for Lines in range 0 to 31
+  * @note This bit is set when the selected edge event arrives on the interrupt
+  *       line. This bit is cleared by writing a 1 to the bit.
+  * @rmtoll PR          PIFx           LL_EXTI_ClearFlag_0_31
+  * @param  ExtiLine This parameter can be a combination of the following values:
+  *         @arg @ref LL_EXTI_LINE_0
+  *         @arg @ref LL_EXTI_LINE_1
+  *         @arg @ref LL_EXTI_LINE_2
+  *         @arg @ref LL_EXTI_LINE_3
+  *         @arg @ref LL_EXTI_LINE_4
+  *         @arg @ref LL_EXTI_LINE_5
+  *         @arg @ref LL_EXTI_LINE_6
+  *         @arg @ref LL_EXTI_LINE_7
+  *         @arg @ref LL_EXTI_LINE_8
+  *         @arg @ref LL_EXTI_LINE_9
+  *         @arg @ref LL_EXTI_LINE_10
+  *         @arg @ref LL_EXTI_LINE_11
+  *         @arg @ref LL_EXTI_LINE_12
+  *         @arg @ref LL_EXTI_LINE_13
+  *         @arg @ref LL_EXTI_LINE_14
+  *         @arg @ref LL_EXTI_LINE_15
+  *         @arg @ref LL_EXTI_LINE_16
+  *         @arg @ref LL_EXTI_LINE_18
+  *         @arg @ref LL_EXTI_LINE_19
+  * @note   Please check each device line mapping for EXTI Line availability
+  * @retval None
+  */
+__STATIC_INLINE void LL_EXTI_ClearFlag_0_31(uint32_t ExtiLine)
+{
+  WRITE_REG(EXTI->PR, ExtiLine);
+}
+
+
+/**
+  * @}
+  */
+
+#if defined(USE_FULL_LL_DRIVER)
+/** @defgroup EXTI_LL_EF_Init Initialization and de-initialization functions
+  * @{
+  */
+
+uint32_t LL_EXTI_Init(LL_EXTI_InitTypeDef *EXTI_InitStruct);
+uint32_t LL_EXTI_DeInit(void);
+void LL_EXTI_StructInit(LL_EXTI_InitTypeDef *EXTI_InitStruct);
+
+
+/**
+  * @}
+  */
+#endif /* USE_FULL_LL_DRIVER */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#endif /* EXTI */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* STM32F1xx_LL_EXTI_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

Drivers/STM32F1xx_HAL_Driver/Inc/stm32f1xx_ll_fsmc.h

@@ -0,0 +1,965 @@
+/**
+  ******************************************************************************
+  * @file    stm32f1xx_ll_fsmc.h
+  * @author  MCD Application Team
+  * @brief   Header file of FSMC HAL module.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; Copyright (c) 2016 STMicroelectronics.
+  * All rights reserved.</center></h2>
+  *
+  * This software component is licensed by ST under BSD 3-Clause license,
+  * the "License"; You may not use this file except in compliance with the
+  * License. You may obtain a copy of the License at:
+  *                       opensource.org/licenses/BSD-3-Clause
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef STM32F1xx_LL_FSMC_H
+#define STM32F1xx_LL_FSMC_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f1xx_hal_def.h"
+
+/** @addtogroup STM32F1xx_HAL_Driver
+  * @{
+  */
+
+/** @addtogroup FSMC_LL
+  * @{
+  */
+
+/** @addtogroup FSMC_LL_Private_Macros
+  * @{
+  */
+#if defined(FSMC_BANK1)
+
+#define IS_FSMC_NORSRAM_BANK(__BANK__) (((__BANK__) == FSMC_NORSRAM_BANK1) || \
+                                       ((__BANK__) == FSMC_NORSRAM_BANK2) || \
+                                       ((__BANK__) == FSMC_NORSRAM_BANK3) || \
+                                       ((__BANK__) == FSMC_NORSRAM_BANK4))
+#define IS_FSMC_MUX(__MUX__) (((__MUX__) == FSMC_DATA_ADDRESS_MUX_DISABLE) || \
+                             ((__MUX__) == FSMC_DATA_ADDRESS_MUX_ENABLE))
+#define IS_FSMC_MEMORY(__MEMORY__) (((__MEMORY__) == FSMC_MEMORY_TYPE_SRAM) || \
+                                   ((__MEMORY__) == FSMC_MEMORY_TYPE_PSRAM)|| \
+                                   ((__MEMORY__) == FSMC_MEMORY_TYPE_NOR))
+#define IS_FSMC_NORSRAM_MEMORY_WIDTH(__WIDTH__) (((__WIDTH__) == FSMC_NORSRAM_MEM_BUS_WIDTH_8)  || \
+                                                ((__WIDTH__) == FSMC_NORSRAM_MEM_BUS_WIDTH_16) || \
+                                                ((__WIDTH__) == FSMC_NORSRAM_MEM_BUS_WIDTH_32))
+#define IS_FSMC_PAGESIZE(__SIZE__) (((__SIZE__) == FSMC_PAGE_SIZE_NONE) || \
+                                   ((__SIZE__) == FSMC_PAGE_SIZE_128) || \
+                                   ((__SIZE__) == FSMC_PAGE_SIZE_256) || \
+                                   ((__SIZE__) == FSMC_PAGE_SIZE_512) || \
+                                   ((__SIZE__) == FSMC_PAGE_SIZE_1024))
+#define IS_FSMC_ACCESS_MODE(__MODE__) (((__MODE__) == FSMC_ACCESS_MODE_A) || \
+                                      ((__MODE__) == FSMC_ACCESS_MODE_B) || \
+                                      ((__MODE__) == FSMC_ACCESS_MODE_C) || \
+                                      ((__MODE__) == FSMC_ACCESS_MODE_D))
+#define IS_FSMC_BURSTMODE(__STATE__) (((__STATE__) == FSMC_BURST_ACCESS_MODE_DISABLE) || \
+                                     ((__STATE__) == FSMC_BURST_ACCESS_MODE_ENABLE))
+#define IS_FSMC_WAIT_POLARITY(__POLARITY__) (((__POLARITY__) == FSMC_WAIT_SIGNAL_POLARITY_LOW) || \
+                                            ((__POLARITY__) == FSMC_WAIT_SIGNAL_POLARITY_HIGH))
+#define IS_FSMC_WRAP_MODE(__MODE__) (((__MODE__) == FSMC_WRAP_MODE_DISABLE) || \
+                                             ((__MODE__) == FSMC_WRAP_MODE_ENABLE))
+#define IS_FSMC_WAIT_SIGNAL_ACTIVE(__ACTIVE__) (((__ACTIVE__) == FSMC_WAIT_TIMING_BEFORE_WS) || \
+                                               ((__ACTIVE__) == FSMC_WAIT_TIMING_DURING_WS))
+#define IS_FSMC_WRITE_OPERATION(__OPERATION__) (((__OPERATION__) == FSMC_WRITE_OPERATION_DISABLE) || \
+                                               ((__OPERATION__) == FSMC_WRITE_OPERATION_ENABLE))
+#define IS_FSMC_WAITE_SIGNAL(__SIGNAL__) (((__SIGNAL__) == FSMC_WAIT_SIGNAL_DISABLE) || \
+                                         ((__SIGNAL__) == FSMC_WAIT_SIGNAL_ENABLE))
+#define IS_FSMC_EXTENDED_MODE(__MODE__) (((__MODE__) == FSMC_EXTENDED_MODE_DISABLE) || \
+                                        ((__MODE__) == FSMC_EXTENDED_MODE_ENABLE))
+#define IS_FSMC_ASYNWAIT(__STATE__) (((__STATE__) == FSMC_ASYNCHRONOUS_WAIT_DISABLE) || \
+                                    ((__STATE__) == FSMC_ASYNCHRONOUS_WAIT_ENABLE))
+#define IS_FSMC_DATA_LATENCY(__LATENCY__) (((__LATENCY__) > 1U) && ((__LATENCY__) <= 17U))
+#define IS_FSMC_WRITE_BURST(__BURST__) (((__BURST__) == FSMC_WRITE_BURST_DISABLE) || \
+                                       ((__BURST__) == FSMC_WRITE_BURST_ENABLE))
+#define IS_FSMC_CONTINOUS_CLOCK(__CCLOCK__) (((__CCLOCK__) == FSMC_CONTINUOUS_CLOCK_SYNC_ONLY) || \
+                                            ((__CCLOCK__) == FSMC_CONTINUOUS_CLOCK_SYNC_ASYNC))
+#define IS_FSMC_ADDRESS_SETUP_TIME(__TIME__) ((__TIME__) <= 15U)
+#define IS_FSMC_ADDRESS_HOLD_TIME(__TIME__) (((__TIME__) > 0U) && ((__TIME__) <= 15U))
+#define IS_FSMC_DATASETUP_TIME(__TIME__) (((__TIME__) > 0U) && ((__TIME__) <= 255U))
+#define IS_FSMC_DATAHOLD_DURATION(__DATAHOLD__) ((__DATAHOLD__) <= 3U)
+#define IS_FSMC_TURNAROUND_TIME(__TIME__) ((__TIME__) <= 15U)
+#define IS_FSMC_CLK_DIV(__DIV__) (((__DIV__) > 1U) && ((__DIV__) <= 16U))
+#define IS_FSMC_NORSRAM_DEVICE(__INSTANCE__) ((__INSTANCE__) == FSMC_NORSRAM_DEVICE)
+#define IS_FSMC_NORSRAM_EXTENDED_DEVICE(__INSTANCE__) ((__INSTANCE__) == FSMC_NORSRAM_EXTENDED_DEVICE)
+
+#endif /* FSMC_BANK1 */
+#if defined(FSMC_BANK3)
+
+#define IS_FSMC_NAND_BANK(__BANK__) ((__BANK__) == FSMC_NAND_BANK3)
+#define IS_FSMC_WAIT_FEATURE(__FEATURE__) (((__FEATURE__) == FSMC_NAND_PCC_WAIT_FEATURE_DISABLE) || \
+                                                   ((__FEATURE__) == FSMC_NAND_PCC_WAIT_FEATURE_ENABLE))
+#define IS_FSMC_NAND_MEMORY_WIDTH(__WIDTH__) (((__WIDTH__) == FSMC_NAND_PCC_MEM_BUS_WIDTH_8) || \
+                                                      ((__WIDTH__) == FSMC_NAND_PCC_MEM_BUS_WIDTH_16))
+#define IS_FSMC_ECC_STATE(__STATE__) (((__STATE__) == FSMC_NAND_ECC_DISABLE) || \
+                                     ((__STATE__) == FSMC_NAND_ECC_ENABLE))
+
+#define IS_FSMC_ECCPAGE_SIZE(__SIZE__) (((__SIZE__) == FSMC_NAND_ECC_PAGE_SIZE_256BYTE)  || \
+                                       ((__SIZE__) == FSMC_NAND_ECC_PAGE_SIZE_512BYTE)  || \
+                                       ((__SIZE__) == FSMC_NAND_ECC_PAGE_SIZE_1024BYTE) || \
+                                       ((__SIZE__) == FSMC_NAND_ECC_PAGE_SIZE_2048BYTE) || \
+                                       ((__SIZE__) == FSMC_NAND_ECC_PAGE_SIZE_4096BYTE) || \
+                                       ((__SIZE__) == FSMC_NAND_ECC_PAGE_SIZE_8192BYTE))
+#define IS_FSMC_TCLR_TIME(__TIME__) ((__TIME__) <= 255U)
+#define IS_FSMC_TAR_TIME(__TIME__) ((__TIME__) <= 255U)
+#define IS_FSMC_SETUP_TIME(__TIME__) ((__TIME__) <= 254U)
+#define IS_FSMC_WAIT_TIME(__TIME__) ((__TIME__) <= 254U)
+#define IS_FSMC_HOLD_TIME(__TIME__) ((__TIME__) <= 254U)
+#define IS_FSMC_HIZ_TIME(__TIME__) ((__TIME__) <= 254U)
+#define IS_FSMC_NAND_DEVICE(__INSTANCE__) ((__INSTANCE__) == FSMC_NAND_DEVICE)
+
+#endif /* FSMC_BANK3 */
+#if defined(FSMC_BANK4)
+#define IS_FSMC_PCCARD_DEVICE(__INSTANCE__) ((__INSTANCE__) == FSMC_PCCARD_DEVICE)
+
+#endif /* FSMC_BANK4 */
+
+/**
+  * @}
+  */
+
+/* Exported typedef ----------------------------------------------------------*/
+
+/** @defgroup FSMC_LL_Exported_typedef FSMC Low Layer Exported Types
+  * @{
+  */
+
+#if defined(FSMC_BANK1)
+#define FSMC_NORSRAM_TypeDef            FSMC_Bank1_TypeDef
+#define FSMC_NORSRAM_EXTENDED_TypeDef   FSMC_Bank1E_TypeDef
+#endif /* FSMC_BANK1 */
+#if defined(FSMC_BANK3)
+#define FSMC_NAND_TypeDef               FSMC_Bank2_3_TypeDef
+#endif /* FSMC_BANK3 */
+#if defined(FSMC_BANK4)
+#define FSMC_PCCARD_TypeDef             FSMC_Bank4_TypeDef
+#endif /* FSMC_BANK4 */
+
+#if defined(FSMC_BANK1)
+#define FSMC_NORSRAM_DEVICE             FSMC_Bank1
+#define FSMC_NORSRAM_EXTENDED_DEVICE    FSMC_Bank1E
+#endif /* FSMC_BANK1 */
+#if defined(FSMC_BANK3)
+#define FSMC_NAND_DEVICE                FSMC_Bank2_3
+#endif /* FSMC_BANK3 */
+#if defined(FSMC_BANK4)
+#define FSMC_PCCARD_DEVICE              FSMC_Bank4
+#endif /* FSMC_BANK4 */
+
+#if defined(FSMC_BANK1)
+/**
+  * @brief  FSMC NORSRAM Configuration Structure definition
+  */
+typedef struct
+{
+  uint32_t NSBank;                       /*!< Specifies the NORSRAM memory device that will be used.
+                                              This parameter can be a value of @ref FSMC_NORSRAM_Bank                  */
+
+  uint32_t DataAddressMux;               /*!< Specifies whether the address and data values are
+                                              multiplexed on the data bus or not.
+                                              This parameter can be a value of @ref FSMC_Data_Address_Bus_Multiplexing */
+
+  uint32_t MemoryType;                   /*!< Specifies the type of external memory attached to
+                                              the corresponding memory device.
+                                              This parameter can be a value of @ref FSMC_Memory_Type                   */
+
+  uint32_t MemoryDataWidth;              /*!< Specifies the external memory device width.
+                                              This parameter can be a value of @ref FSMC_NORSRAM_Data_Width            */
+
+  uint32_t BurstAccessMode;              /*!< Enables or disables the burst access mode for Flash memory,
+                                              valid only with synchronous burst Flash memories.
+                                              This parameter can be a value of @ref FSMC_Burst_Access_Mode             */
+
+  uint32_t WaitSignalPolarity;           /*!< Specifies the wait signal polarity, valid only when accessing
+                                              the Flash memory in burst mode.
+                                              This parameter can be a value of @ref FSMC_Wait_Signal_Polarity          */
+
+  uint32_t WrapMode;                     /*!< Enables or disables the Wrapped burst access mode for Flash
+                                              memory, valid only when accessing Flash memories in burst mode.
+                                              This parameter can be a value of @ref FSMC_Wrap_Mode                     */
+
+  uint32_t WaitSignalActive;             /*!< Specifies if the wait signal is asserted by the memory one
+                                              clock cycle before the wait state or during the wait state,
+                                              valid only when accessing memories in burst mode.
+                                              This parameter can be a value of @ref FSMC_Wait_Timing                   */
+
+  uint32_t WriteOperation;               /*!< Enables or disables the write operation in the selected device by the FSMC.
+                                              This parameter can be a value of @ref FSMC_Write_Operation               */
+
+  uint32_t WaitSignal;                   /*!< Enables or disables the wait state insertion via wait
+                                              signal, valid for Flash memory access in burst mode.
+                                              This parameter can be a value of @ref FSMC_Wait_Signal                   */
+
+  uint32_t ExtendedMode;                 /*!< Enables or disables the extended mode.
+                                              This parameter can be a value of @ref FSMC_Extended_Mode                 */
+
+  uint32_t AsynchronousWait;             /*!< Enables or disables wait signal during asynchronous transfers,
+                                              valid only with asynchronous Flash memories.
+                                              This parameter can be a value of @ref FSMC_AsynchronousWait              */
+
+  uint32_t WriteBurst;                   /*!< Enables or disables the write burst operation.
+                                              This parameter can be a value of @ref FSMC_Write_Burst                   */
+
+
+  uint32_t PageSize;                     /*!< Specifies the memory page size.
+                                              This parameter can be a value of @ref FSMC_Page_Size                     */
+} FSMC_NORSRAM_InitTypeDef;
+
+/**
+  * @brief  FSMC NORSRAM Timing parameters structure definition
+  */
+typedef struct
+{
+  uint32_t AddressSetupTime;             /*!< Defines the number of HCLK cycles to configure
+                                              the duration of the address setup time.
+                                              This parameter can be a value between Min_Data = 0 and Max_Data = 15.
+                                              @note This parameter is not used with synchronous NOR Flash memories.   */
+
+  uint32_t AddressHoldTime;              /*!< Defines the number of HCLK cycles to configure
+                                              the duration of the address hold time.
+                                              This parameter can be a value between Min_Data = 1 and Max_Data = 15.
+                                              @note This parameter is not used with synchronous NOR Flash memories.   */
+
+  uint32_t DataSetupTime;                /*!< Defines the number of HCLK cycles to configure
+                                              the duration of the data setup time.
+                                              This parameter can be a value between Min_Data = 1 and Max_Data = 255.
+                                              @note This parameter is used for SRAMs, ROMs and asynchronous multiplexed
+                                              NOR Flash memories.                                                     */
+
+  uint32_t BusTurnAroundDuration;        /*!< Defines the number of HCLK cycles to configure
+                                              the duration of the bus turnaround.
+                                              This parameter can be a value between Min_Data = 0 and Max_Data = 15.
+                                              @note This parameter is only used for multiplexed NOR Flash memories.   */
+
+  uint32_t CLKDivision;                  /*!< Defines the period of CLK clock output signal, expressed in number of
+                                              HCLK cycles. This parameter can be a value between Min_Data = 2 and
+                                              Max_Data = 16.
+                                              @note This parameter is not used for asynchronous NOR Flash, SRAM or ROM
+                                              accesses.                                                               */
+
+  uint32_t DataLatency;                  /*!< Defines the number of memory clock cycles to issue
+                                              to the memory before getting the first data.
+                                              The parameter value depends on the memory type as shown below:
+                                              - It must be set to 0 in case of a CRAM
+                                              - It is don't care in asynchronous NOR, SRAM or ROM accesses
+                                              - It may assume a value between Min_Data = 2 and Max_Data = 17
+                                                in NOR Flash memories with synchronous burst mode enable              */
+
+  uint32_t AccessMode;                   /*!< Specifies the asynchronous access mode.
+                                              This parameter can be a value of @ref FSMC_Access_Mode                   */
+} FSMC_NORSRAM_TimingTypeDef;
+#endif /* FSMC_BANK1 */
+
+#if defined(FSMC_BANK3)
+/**
+  * @brief  FSMC NAND Configuration Structure definition
+  */
+typedef struct
+{
+  uint32_t NandBank;               /*!< Specifies the NAND memory device that will be used.
+                                        This parameter can be a value of @ref FSMC_NAND_Bank                  */
+
+  uint32_t Waitfeature;            /*!< Enables or disables the Wait feature for the NAND Memory device.
+                                        This parameter can be any value of @ref FSMC_Wait_feature             */
+
+  uint32_t MemoryDataWidth;        /*!< Specifies the external memory device width.
+                                        This parameter can be any value of @ref FSMC_NAND_Data_Width          */
+
+  uint32_t EccComputation;         /*!< Enables or disables the ECC computation.
+                                        This parameter can be any value of @ref FSMC_ECC                      */
+
+  uint32_t ECCPageSize;            /*!< Defines the page size for the extended ECC.
+                                        This parameter can be any value of @ref FSMC_ECC_Page_Size            */
+
+  uint32_t TCLRSetupTime;          /*!< Defines the number of HCLK cycles to configure the
+                                        delay between CLE low and RE low.
+                                        This parameter can be a value between Min_Data = 0 and Max_Data = 255  */
+
+  uint32_t TARSetupTime;           /*!< Defines the number of HCLK cycles to configure the
+                                        delay between ALE low and RE low.
+                                        This parameter can be a number between Min_Data = 0 and Max_Data = 255 */
+} FSMC_NAND_InitTypeDef;
+#endif
+
+#if defined(FSMC_BANK3) || defined(FSMC_BANK4)
+/**
+  * @brief  FSMC NAND Timing parameters structure definition
+  */
+typedef struct
+{
+  uint32_t SetupTime;            /*!< Defines the number of HCLK cycles to setup address before
+                                      the command assertion for NAND-Flash read or write access
+                                      to common/Attribute or I/O memory space (depending on
+                                      the memory space timing to be configured).
+                                      This parameter can be a value between Min_Data = 0 and Max_Data = 254    */
+
+  uint32_t WaitSetupTime;        /*!< Defines the minimum number of HCLK cycles to assert the
+                                      command for NAND-Flash read or write access to
+                                      common/Attribute or I/O memory space (depending on the
+                                      memory space timing to be configured).
+                                      This parameter can be a number between Min_Data = 0 and Max_Data = 254   */
+
+  uint32_t HoldSetupTime;        /*!< Defines the number of HCLK clock cycles to hold address
+                                      (and data for write access) after the command de-assertion
+                                      for NAND-Flash read or write access to common/Attribute
+                                      or I/O memory space (depending on the memory space timing
+                                      to be configured).
+                                      This parameter can be a number between Min_Data = 0 and Max_Data = 254   */
+
+  uint32_t HiZSetupTime;         /*!< Defines the number of HCLK clock cycles during which the
+                                      data bus is kept in HiZ after the start of a NAND-Flash
+                                      write access to common/Attribute or I/O memory space (depending
+                                      on the memory space timing to be configured).
+                                      This parameter can be a number between Min_Data = 0 and Max_Data = 254   */
+} FSMC_NAND_PCC_TimingTypeDef;
+#endif /* FSMC_BANK3 */
+
+#if defined(FSMC_BANK4)
+/**
+  * @brief FSMC PCCARD Configuration Structure definition
+  */
+typedef struct
+{
+  uint32_t Waitfeature;            /*!< Enables or disables the Wait feature for the PCCARD Memory device.
+                                        This parameter can be any value of @ref FSMC_Wait_feature      */
+
+  uint32_t TCLRSetupTime;          /*!< Defines the number of HCLK cycles to configure the
+                                        delay between CLE low and RE low.
+                                        This parameter can be a value between Min_Data = 0 and Max_Data = 255  */
+
+  uint32_t TARSetupTime;           /*!< Defines the number of HCLK cycles to configure the
+                                        delay between ALE low and RE low.
+                                        This parameter can be a number between Min_Data = 0 and Max_Data = 255 */
+}FSMC_PCCARD_InitTypeDef;
+#endif
+
+/**
+  * @}
+  */
+
+/* Exported constants --------------------------------------------------------*/
+/** @addtogroup FSMC_LL_Exported_Constants FSMC Low Layer Exported Constants
+  * @{
+  */
+#if defined(FSMC_BANK1)
+
+/** @defgroup FSMC_LL_NOR_SRAM_Controller FSMC NOR/SRAM Controller
+  * @{
+  */
+
+/** @defgroup FSMC_NORSRAM_Bank FSMC NOR/SRAM Bank
+  * @{
+  */
+#define FSMC_NORSRAM_BANK1                       (0x00000000U)
+#define FSMC_NORSRAM_BANK2                       (0x00000002U)
+#define FSMC_NORSRAM_BANK3                       (0x00000004U)
+#define FSMC_NORSRAM_BANK4                       (0x00000006U)
+/**
+  * @}
+  */
+
+/** @defgroup FSMC_Data_Address_Bus_Multiplexing FSMC Data Address Bus Multiplexing
+  * @{
+  */
+#define FSMC_DATA_ADDRESS_MUX_DISABLE            (0x00000000U)
+#define FSMC_DATA_ADDRESS_MUX_ENABLE             (0x00000002U)
+/**
+  * @}
+  */
+
+/** @defgroup FSMC_Memory_Type FSMC Memory Type
+  * @{
+  */
+#define FSMC_MEMORY_TYPE_SRAM                    (0x00000000U)
+#define FSMC_MEMORY_TYPE_PSRAM                   (0x00000004U)
+#define FSMC_MEMORY_TYPE_NOR                     (0x00000008U)
+/**
+  * @}
+  */
+
+/** @defgroup FSMC_NORSRAM_Data_Width FSMC NORSRAM Data Width
+  * @{
+  */
+#define FSMC_NORSRAM_MEM_BUS_WIDTH_8             (0x00000000U)
+#define FSMC_NORSRAM_MEM_BUS_WIDTH_16            (0x00000010U)
+#define FSMC_NORSRAM_MEM_BUS_WIDTH_32            (0x00000020U)
+/**
+  * @}
+  */
+
+/** @defgroup FSMC_NORSRAM_Flash_Access FSMC NOR/SRAM Flash Access
+  * @{
+  */
+#define FSMC_NORSRAM_FLASH_ACCESS_ENABLE         (0x00000040U)
+#define FSMC_NORSRAM_FLASH_ACCESS_DISABLE        (0x00000000U)
+/**
+  * @}
+  */
+
+/** @defgroup FSMC_Burst_Access_Mode FSMC Burst Access Mode
+  * @{
+  */
+#define FSMC_BURST_ACCESS_MODE_DISABLE           (0x00000000U)
+#define FSMC_BURST_ACCESS_MODE_ENABLE            (0x00000100U)
+/**
+  * @}
+  */
+
+/** @defgroup FSMC_Wait_Signal_Polarity FSMC Wait Signal Polarity
+  * @{
+  */
+#define FSMC_WAIT_SIGNAL_POLARITY_LOW            (0x00000000U)
+#define FSMC_WAIT_SIGNAL_POLARITY_HIGH           (0x00000200U)
+/**
+  * @}
+  */
+
+/** @defgroup FSMC_Wrap_Mode FSMC Wrap Mode
+  * @{
+  */
+#define FSMC_WRAP_MODE_DISABLE                   (0x00000000U)
+#define FSMC_WRAP_MODE_ENABLE                    (0x00000400U)
+/**
+  * @}
+  */
+
+/** @defgroup FSMC_Wait_Timing FSMC Wait Timing
+  * @{
+  */
+#define FSMC_WAIT_TIMING_BEFORE_WS               (0x00000000U)
+#define FSMC_WAIT_TIMING_DURING_WS               (0x00000800U)
+/**
+  * @}
+  */
+
+/** @defgroup FSMC_Write_Operation FSMC Write Operation
+  * @{
+  */
+#define FSMC_WRITE_OPERATION_DISABLE             (0x00000000U)
+#define FSMC_WRITE_OPERATION_ENABLE              (0x00001000U)
+/**
+  * @}
+  */
+
+/** @defgroup FSMC_Wait_Signal FSMC Wait Signal
+  * @{
+  */
+#define FSMC_WAIT_SIGNAL_DISABLE                 (0x00000000U)
+#define FSMC_WAIT_SIGNAL_ENABLE                  (0x00002000U)
+/**
+  * @}
+  */
+
+/** @defgroup FSMC_Extended_Mode FSMC Extended Mode
+  * @{
+  */
+#define FSMC_EXTENDED_MODE_DISABLE               (0x00000000U)
+#define FSMC_EXTENDED_MODE_ENABLE                (0x00004000U)
+/**
+  * @}
+  */
+
+/** @defgroup FSMC_AsynchronousWait FSMC Asynchronous Wait
+  * @{
+  */
+#define FSMC_ASYNCHRONOUS_WAIT_DISABLE           (0x00000000U)
+#define FSMC_ASYNCHRONOUS_WAIT_ENABLE            (0x00008000U)
+/**
+  * @}
+  */
+
+/** @defgroup FSMC_Page_Size FSMC Page Size
+  * @{
+  */
+#define FSMC_PAGE_SIZE_NONE                      (0x00000000U)
+#define FSMC_PAGE_SIZE_128                       (0x00010000U)
+#define FSMC_PAGE_SIZE_256                       (0x00020000U)
+#define FSMC_PAGE_SIZE_512                       (0x00030000U)
+#define FSMC_PAGE_SIZE_1024                      (0x00040000U)
+/**
+  * @}
+  */
+
+/** @defgroup FSMC_Write_Burst FSMC Write Burst
+  * @{
+  */
+#define FSMC_WRITE_BURST_DISABLE                 (0x00000000U)
+#define FSMC_WRITE_BURST_ENABLE                  (0x00080000U)
+/**
+  * @}
+  */
+
+/** @defgroup FSMC_Continous_Clock FSMC Continuous Clock
+  * @{
+  */
+#define FSMC_CONTINUOUS_CLOCK_SYNC_ONLY          (0x00000000U)
+#define FSMC_CONTINUOUS_CLOCK_SYNC_ASYNC         (0x00100000U)
+/**
+  * @}
+  */
+
+/** @defgroup FSMC_Access_Mode FSMC Access Mode
+  * @{
+  */
+#define FSMC_ACCESS_MODE_A                       (0x00000000U)
+#define FSMC_ACCESS_MODE_B                       (0x10000000U)
+#define FSMC_ACCESS_MODE_C                       (0x20000000U)
+#define FSMC_ACCESS_MODE_D                       (0x30000000U)
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+#endif /* FSMC_BANK1 */
+
+#if defined(FSMC_BANK3) || defined(FSMC_BANK4)
+
+/** @defgroup FSMC_LL_NAND_Controller FSMC NAND Controller
+  * @{
+  */
+/** @defgroup FSMC_NAND_Bank FSMC NAND Bank
+  * @{
+  */
+#define FSMC_NAND_BANK2                          (0x00000010U)
+#define FSMC_NAND_BANK3                          (0x00000100U)
+/**
+  * @}
+  */
+
+/** @defgroup FSMC_Wait_feature FSMC Wait feature
+  * @{
+  */
+#define FSMC_NAND_PCC_WAIT_FEATURE_DISABLE       (0x00000000U)
+#define FSMC_NAND_PCC_WAIT_FEATURE_ENABLE        (0x00000002U)
+/**
+  * @}
+  */
+
+/** @defgroup FSMC_PCR_Memory_Type FSMC PCR Memory Type
+  * @{
+  */
+#if defined(FSMC_BANK4)
+#define FSMC_PCR_MEMORY_TYPE_PCCARD              (0x00000000U)
+#endif
+#define FSMC_PCR_MEMORY_TYPE_NAND                (0x00000008U)
+/**
+  * @}
+  */
+
+/** @defgroup FSMC_NAND_Data_Width FSMC NAND Data Width
+  * @{
+  */
+#define FSMC_NAND_PCC_MEM_BUS_WIDTH_8            (0x00000000U)
+#define FSMC_NAND_PCC_MEM_BUS_WIDTH_16           (0x00000010U)
+/**
+  * @}
+  */
+
+/** @defgroup FSMC_ECC FSMC ECC
+  * @{
+  */
+#define FSMC_NAND_ECC_DISABLE                    (0x00000000U)
+#define FSMC_NAND_ECC_ENABLE                     (0x00000040U)
+/**
+  * @}
+  */
+
+/** @defgroup FSMC_ECC_Page_Size FSMC ECC Page Size
+  * @{
+  */
+#define FSMC_NAND_ECC_PAGE_SIZE_256BYTE          (0x00000000U)
+#define FSMC_NAND_ECC_PAGE_SIZE_512BYTE          (0x00020000U)
+#define FSMC_NAND_ECC_PAGE_SIZE_1024BYTE         (0x00040000U)
+#define FSMC_NAND_ECC_PAGE_SIZE_2048BYTE         (0x00060000U)
+#define FSMC_NAND_ECC_PAGE_SIZE_4096BYTE         (0x00080000U)
+#define FSMC_NAND_ECC_PAGE_SIZE_8192BYTE         (0x000A0000U)
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+#endif /* FSMC_BANK3 */
+
+
+/** @defgroup FSMC_LL_Interrupt_definition FSMC Low Layer Interrupt definition
+  * @{
+  */
+#if defined(FSMC_BANK3) || defined(FSMC_BANK4)
+#define FSMC_IT_RISING_EDGE                      (0x00000008U)
+#define FSMC_IT_LEVEL                            (0x00000010U)
+#define FSMC_IT_FALLING_EDGE                     (0x00000020U)
+#endif /* FSMC_BANK3 */
+/**
+  * @}
+  */
+
+/** @defgroup FSMC_LL_Flag_definition FSMC Low Layer Flag definition
+  * @{
+  */
+#if defined(FSMC_BANK3) || defined(FSMC_BANK4)
+#define FSMC_FLAG_RISING_EDGE                    (0x00000001U)
+#define FSMC_FLAG_LEVEL                          (0x00000002U)
+#define FSMC_FLAG_FALLING_EDGE                   (0x00000004U)
+#define FSMC_FLAG_FEMPT                          (0x00000040U)
+#endif /* FSMC_BANK3 */
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Private macro -------------------------------------------------------------*/
+/** @defgroup FSMC_LL_Private_Macros FSMC_LL  Private Macros
+  * @{
+  */
+#if defined(FSMC_BANK1)
+/** @defgroup FSMC_LL_NOR_Macros FSMC NOR/SRAM Macros
+  * @brief macros to handle NOR device enable/disable and read/write operations
+  * @{
+  */
+
+/**
+  * @brief  Enable the NORSRAM device access.
+  * @param  __INSTANCE__ FSMC_NORSRAM Instance
+  * @param  __BANK__ FSMC_NORSRAM Bank
+  * @retval None
+  */
+#define __FSMC_NORSRAM_ENABLE(__INSTANCE__, __BANK__)  ((__INSTANCE__)->BTCR[(__BANK__)]\
+                                                       |= FSMC_BCRx_MBKEN)
+
+/**
+  * @brief  Disable the NORSRAM device access.
+  * @param  __INSTANCE__ FSMC_NORSRAM Instance
+  * @param  __BANK__ FSMC_NORSRAM Bank
+  * @retval None
+  */
+#define __FSMC_NORSRAM_DISABLE(__INSTANCE__, __BANK__) ((__INSTANCE__)->BTCR[(__BANK__)]\
+                                                       &= ~FSMC_BCRx_MBKEN)
+
+/**
+  * @}
+  */
+#endif /* FSMC_BANK1 */
+
+#if defined(FSMC_BANK3)
+/** @defgroup FSMC_LL_NAND_Macros FSMC NAND Macros
+  *  @brief macros to handle NAND device enable/disable
+  *  @{
+  */
+
+/**
+  * @brief  Enable the NAND device access.
+  * @param  __INSTANCE__ FSMC_NAND Instance
+  * @param  __BANK__     FSMC_NAND Bank
+  * @retval None
+  */
+#define __FSMC_NAND_ENABLE(__INSTANCE__, __BANK__)  (((__BANK__) == FSMC_NAND_BANK2)? ((__INSTANCE__)->PCR2 |= FSMC_PCRx_PBKEN): \
+                                                             ((__INSTANCE__)->PCR3 |= FSMC_PCRx_PBKEN))
+
+/**
+  * @brief  Disable the NAND device access.
+  * @param  __INSTANCE__ FSMC_NAND Instance
+  * @param  __BANK__     FSMC_NAND Bank
+  * @retval None
+  */
+#define __FSMC_NAND_DISABLE(__INSTANCE__, __BANK__) (((__BANK__) == FSMC_NAND_BANK2)? CLEAR_BIT((__INSTANCE__)->PCR2, FSMC_PCRx_PBKEN): \
+                                                             CLEAR_BIT((__INSTANCE__)->PCR3, FSMC_PCRx_PBKEN))
+
+/**
+  * @}
+  */
+#endif
+
+#if defined(FSMC_BANK4)
+/** @defgroup FSMC_LL_PCCARD_Macros FMC PCCARD Macros
+  *  @brief macros to handle PCCARD read/write operations
+  *  @{
+  */
+/**
+  * @brief  Enable the PCCARD device access.
+  * @param  __INSTANCE__ FSMC_PCCARD Instance
+  * @retval None
+  */
+#define __FSMC_PCCARD_ENABLE(__INSTANCE__)  ((__INSTANCE__)->PCR4 |= FSMC_PCRx_PBKEN)
+
+/**
+  * @brief  Disable the PCCARD device access.
+  * @param  __INSTANCE__ FSMC_PCCARD Instance
+  * @retval None
+  */
+#define __FSMC_PCCARD_DISABLE(__INSTANCE__) ((__INSTANCE__)->PCR4 &= ~FSMC_PCRx_PBKEN)
+/**
+  * @}
+  */
+
+#endif
+#if defined(FSMC_BANK3)
+/** @defgroup FSMC_LL_NAND_Interrupt FSMC NAND Interrupt
+  * @brief macros to handle NAND interrupts
+  * @{
+  */
+
+/**
+  * @brief  Enable the NAND device interrupt.
+  * @param  __INSTANCE__  FSMC_NAND instance
+  * @param  __BANK__     FSMC_NAND Bank
+  * @param  __INTERRUPT__ FSMC_NAND interrupt
+  *         This parameter can be any combination of the following values:
+  *            @arg FSMC_IT_RISING_EDGE: Interrupt rising edge.
+  *            @arg FSMC_IT_LEVEL: Interrupt level.
+  *            @arg FSMC_IT_FALLING_EDGE: Interrupt falling edge.
+  * @retval None
+  */
+#define __FSMC_NAND_ENABLE_IT(__INSTANCE__, __BANK__, __INTERRUPT__)  (((__BANK__) == FSMC_NAND_BANK2)? ((__INSTANCE__)->SR2 |= (__INTERRUPT__)): \
+                                                                               ((__INSTANCE__)->SR3 |= (__INTERRUPT__)))
+
+/**
+  * @brief  Disable the NAND device interrupt.
+  * @param  __INSTANCE__  FSMC_NAND Instance
+  * @param  __BANK__     FSMC_NAND Bank
+  * @param  __INTERRUPT__ FSMC_NAND interrupt
+  *         This parameter can be any combination of the following values:
+  *            @arg FSMC_IT_RISING_EDGE: Interrupt rising edge.
+  *            @arg FSMC_IT_LEVEL: Interrupt level.
+  *            @arg FSMC_IT_FALLING_EDGE: Interrupt falling edge.
+  * @retval None
+  */
+#define __FSMC_NAND_DISABLE_IT(__INSTANCE__, __BANK__, __INTERRUPT__)  (((__BANK__) == FSMC_NAND_BANK2)? ((__INSTANCE__)->SR2 &= ~(__INTERRUPT__)): \
+                                                                                ((__INSTANCE__)->SR3 &= ~(__INTERRUPT__)))
+
+/**
+  * @brief  Get flag status of the NAND device.
+  * @param  __INSTANCE__ FSMC_NAND Instance
+  * @param  __BANK__     FSMC_NAND Bank
+  * @param  __FLAG__     FSMC_NAND flag
+  *         This parameter can be any combination of the following values:
+  *            @arg FSMC_FLAG_RISING_EDGE: Interrupt rising edge flag.
+  *            @arg FSMC_FLAG_LEVEL: Interrupt level edge flag.
+  *            @arg FSMC_FLAG_FALLING_EDGE: Interrupt falling edge flag.
+  *            @arg FSMC_FLAG_FEMPT: FIFO empty flag.
+  * @retval The state of FLAG (SET or RESET).
+  */
+#define __FSMC_NAND_GET_FLAG(__INSTANCE__, __BANK__, __FLAG__)  (((__BANK__) == FSMC_NAND_BANK2)? (((__INSTANCE__)->SR2 &(__FLAG__)) == (__FLAG__)): \
+                                                                         (((__INSTANCE__)->SR3 &(__FLAG__)) == (__FLAG__)))
+
+/**
+  * @brief  Clear flag status of the NAND device.
+  * @param  __INSTANCE__ FSMC_NAND Instance
+  * @param  __BANK__     FSMC_NAND Bank
+  * @param  __FLAG__     FSMC_NAND flag
+  *         This parameter can be any combination of the following values:
+  *            @arg FSMC_FLAG_RISING_EDGE: Interrupt rising edge flag.
+  *            @arg FSMC_FLAG_LEVEL: Interrupt level edge flag.
+  *            @arg FSMC_FLAG_FALLING_EDGE: Interrupt falling edge flag.
+  *            @arg FSMC_FLAG_FEMPT: FIFO empty flag.
+  * @retval None
+  */
+#define __FSMC_NAND_CLEAR_FLAG(__INSTANCE__, __BANK__, __FLAG__)  (((__BANK__) == FSMC_NAND_BANK2)? ((__INSTANCE__)->SR2 &= ~(__FLAG__)): \
+                                                                           ((__INSTANCE__)->SR3 &= ~(__FLAG__)))
+
+/**
+  * @}
+  */
+#endif /* FSMC_BANK3 */
+
+#if defined(FSMC_BANK4)
+/** @defgroup FSMC_LL_PCCARD_Interrupt FSMC PCCARD Interrupt
+  * @brief macros to handle PCCARD interrupts
+  * @{
+  */
+
+/**
+  * @brief  Enable the PCCARD device interrupt.
+  * @param  __INSTANCE__ FSMC_PCCARD instance
+  * @param  __INTERRUPT__ FSMC_PCCARD interrupt
+  *         This parameter can be any combination of the following values:
+  *            @arg FSMC_IT_RISING_EDGE: Interrupt rising edge.
+  *            @arg FSMC_IT_LEVEL: Interrupt level.
+  *            @arg FSMC_IT_FALLING_EDGE: Interrupt falling edge.
+  * @retval None
+  */
+#define __FSMC_PCCARD_ENABLE_IT(__INSTANCE__, __INTERRUPT__)  ((__INSTANCE__)->SR4 |= (__INTERRUPT__))
+
+/**
+  * @brief  Disable the PCCARD device interrupt.
+  * @param  __INSTANCE__ FSMC_PCCARD instance
+  * @param  __INTERRUPT__ FSMC_PCCARD interrupt
+  *         This parameter can be any combination of the following values:
+  *            @arg FSMC_IT_RISING_EDGE: Interrupt rising edge.
+  *            @arg FSMC_IT_LEVEL: Interrupt level.
+  *            @arg FSMC_IT_FALLING_EDGE: Interrupt falling edge.
+  * @retval None
+  */
+#define __FSMC_PCCARD_DISABLE_IT(__INSTANCE__, __INTERRUPT__)  ((__INSTANCE__)->SR4 &= ~(__INTERRUPT__))
+
+/**
+  * @brief  Get flag status of the PCCARD device.
+  * @param  __INSTANCE__ FSMC_PCCARD instance
+  * @param  __FLAG__ FSMC_PCCARD flag
+  *         This parameter can be any combination of the following values:
+  *            @arg  FSMC_FLAG_RISING_EDGE: Interrupt rising edge flag.
+  *            @arg  FSMC_FLAG_LEVEL: Interrupt level edge flag.
+  *            @arg  FSMC_FLAG_FALLING_EDGE: Interrupt falling edge flag.
+  *            @arg  FSMC_FLAG_FEMPT: FIFO empty flag.
+  * @retval The state of FLAG (SET or RESET).
+  */
+#define __FSMC_PCCARD_GET_FLAG(__INSTANCE__, __FLAG__)  (((__INSTANCE__)->SR4 &(__FLAG__)) == (__FLAG__))
+
+/**
+  * @brief  Clear flag status of the PCCARD device.
+  * @param  __INSTANCE__ FSMC_PCCARD instance
+  * @param  __FLAG__ FSMC_PCCARD flag
+  *         This parameter can be any combination of the following values:
+  *            @arg  FSMC_FLAG_RISING_EDGE: Interrupt rising edge flag.
+  *            @arg  FSMC_FLAG_LEVEL: Interrupt level edge flag.
+  *            @arg  FSMC_FLAG_FALLING_EDGE: Interrupt falling edge flag.
+  *            @arg  FSMC_FLAG_FEMPT: FIFO empty flag.
+  * @retval None
+  */
+#define __FSMC_PCCARD_CLEAR_FLAG(__INSTANCE__, __FLAG__)  ((__INSTANCE__)->SR4 &= ~(__FLAG__))
+
+/**
+  * @}
+  */
+#endif
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/* Private functions ---------------------------------------------------------*/
+/** @defgroup FSMC_LL_Private_Functions FSMC LL Private Functions
+  *  @{
+  */
+
+#if defined(FSMC_BANK1)
+/** @defgroup FSMC_LL_NORSRAM  NOR SRAM
+  *  @{
+  */
+/** @defgroup FSMC_LL_NORSRAM_Private_Functions_Group1 NOR SRAM Initialization/de-initialization functions
+  *  @{
+  */
+HAL_StatusTypeDef  FSMC_NORSRAM_Init(FSMC_NORSRAM_TypeDef *Device,
+                                    FSMC_NORSRAM_InitTypeDef *Init);
+HAL_StatusTypeDef  FSMC_NORSRAM_Timing_Init(FSMC_NORSRAM_TypeDef *Device,
+                                           FSMC_NORSRAM_TimingTypeDef *Timing, uint32_t Bank);
+HAL_StatusTypeDef  FSMC_NORSRAM_Extended_Timing_Init(FSMC_NORSRAM_EXTENDED_TypeDef *Device,
+                                                    FSMC_NORSRAM_TimingTypeDef *Timing, uint32_t Bank,
+                                                    uint32_t ExtendedMode);
+HAL_StatusTypeDef  FSMC_NORSRAM_DeInit(FSMC_NORSRAM_TypeDef *Device,
+                                      FSMC_NORSRAM_EXTENDED_TypeDef *ExDevice, uint32_t Bank);
+/**
+  * @}
+  */
+
+/** @defgroup FSMC_LL_NORSRAM_Private_Functions_Group2 NOR SRAM Control functions
+  *  @{
+  */
+HAL_StatusTypeDef  FSMC_NORSRAM_WriteOperation_Enable(FSMC_NORSRAM_TypeDef *Device, uint32_t Bank);
+HAL_StatusTypeDef  FSMC_NORSRAM_WriteOperation_Disable(FSMC_NORSRAM_TypeDef *Device, uint32_t Bank);
+/**
+  * @}
+  */
+/**
+  * @}
+  */
+#endif /* FSMC_BANK1 */
+
+#if defined(FSMC_BANK3)
+/** @defgroup FSMC_LL_NAND NAND
+  *  @{
+  */
+/** @defgroup FSMC_LL_NAND_Private_Functions_Group1 NAND Initialization/de-initialization functions
+  *  @{
+  */
+HAL_StatusTypeDef  FSMC_NAND_Init(FSMC_NAND_TypeDef *Device, FSMC_NAND_InitTypeDef *Init);
+HAL_StatusTypeDef  FSMC_NAND_CommonSpace_Timing_Init(FSMC_NAND_TypeDef *Device,
+                                                    FSMC_NAND_PCC_TimingTypeDef *Timing, uint32_t Bank);
+HAL_StatusTypeDef  FSMC_NAND_AttributeSpace_Timing_Init(FSMC_NAND_TypeDef *Device,
+                                                       FSMC_NAND_PCC_TimingTypeDef *Timing, uint32_t Bank);
+HAL_StatusTypeDef  FSMC_NAND_DeInit(FSMC_NAND_TypeDef *Device, uint32_t Bank);
+/**
+  * @}
+  */
+
+/** @defgroup FSMC_LL_NAND_Private_Functions_Group2 NAND Control functions
+  *  @{
+  */
+HAL_StatusTypeDef  FSMC_NAND_ECC_Enable(FSMC_NAND_TypeDef *Device, uint32_t Bank);
+HAL_StatusTypeDef  FSMC_NAND_ECC_Disable(FSMC_NAND_TypeDef *Device, uint32_t Bank);
+HAL_StatusTypeDef  FSMC_NAND_GetECC(FSMC_NAND_TypeDef *Device, uint32_t *ECCval, uint32_t Bank,
+                                   uint32_t Timeout);
+/**
+  * @}
+  */
+/**
+  * @}
+  */
+#endif /* FSMC_BANK3 */
+
+#if defined(FSMC_BANK4)
+/** @defgroup FSMC_LL_PCCARD PCCARD
+  *  @{
+  */
+/** @defgroup FSMC_LL_PCCARD_Private_Functions_Group1 PCCARD Initialization/de-initialization functions
+  *  @{
+  */
+HAL_StatusTypeDef  FSMC_PCCARD_Init(FSMC_PCCARD_TypeDef *Device, FSMC_PCCARD_InitTypeDef *Init);
+HAL_StatusTypeDef  FSMC_PCCARD_CommonSpace_Timing_Init(FSMC_PCCARD_TypeDef *Device,
+                                                               FSMC_NAND_PCC_TimingTypeDef *Timing);
+HAL_StatusTypeDef  FSMC_PCCARD_AttributeSpace_Timing_Init(FSMC_PCCARD_TypeDef *Device,
+                                                                  FSMC_NAND_PCC_TimingTypeDef *Timing);
+HAL_StatusTypeDef  FSMC_PCCARD_IOSpace_Timing_Init(FSMC_PCCARD_TypeDef *Device,
+                                                           FSMC_NAND_PCC_TimingTypeDef *Timing);
+HAL_StatusTypeDef  FSMC_PCCARD_DeInit(FSMC_PCCARD_TypeDef *Device);
+/**
+  * @}
+  */
+/**
+  * @}
+  */
+#endif /* FSMC_BANK4 */
+
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* STM32F1xx_LL_FSMC_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/